A man comparing an XtremepowerUS and DC House earth auger in an open yard

XtremepowerUS vs DC HOUSE Auger: Corded Plug-In or Gas Engine for Home Holes

Garden Power Scout Amazon Black Friday Banner

Affiliate Disclosure: Garden Power Scout is a proud participant in the Amazon Services LLC Associates Program. As an Amazon Associate, we earn from qualifying purchases, at no extra cost to you.

The XtremepowerUS vs DC HOUSE auger choice comes down to a plug or a fuel can. For a few holes within reach of an outdoor outlet I pick the corded XtremepowerUS 85060 Corded Electric Post Hole Digger with 6-Inch Bit, and for ground beyond the cord I pick the gas DC HOUSE 52cc Gas Earth Auger with 6-Inch and 10-Inch Bits.

Affiliate Disclosure: Garden Power Scout is a proud participant in the Amazon Services LLC Associates Program.

I run a 3.7-acre apricot and plum orchard, and I read a digging tool’s manual line by line before it goes near my ground. On bit size, depth and watts, the manuals and the product pages disagree.

XtremepowerUS vs DC HOUSE Auger: The Short Answer

Pick the XtremepowerUS 85060 if your holes sit within reach of a safe outdoor outlet and you want no fuel to mix, store or burn. The DC HOUSE 52cc is the one for a spot no outlet reaches, or for a kit that the product page sells with 6 in and 10 in bits. Both manuals say not to use the machine in excessively rocky ground, and neither machine goes into the ground before the 811 process is finished.

Head to head, figure by figure as each maker prints it
Row XtremepowerUS 85060 DC HOUSE 52cc
Auger type Corded electric earth auger (the manual calls it a hole digger) Gas earth auger, 2-cycle, recoil start
Power source Corded, 110 V, 60 Hz Mixed gas and oil, 52 cc engine
Motor or engine, maker’s figure 10.9 amp (manual); cover says 1500W, package list says 1200W Maximum output 1.3 kW at 7000 r/min (manual table)
Bits in the kit One bit; the product page says 6 in on a 3/4 in shaft Product page: 6 in and 10 in bits and a fuel mixing bottle; manual: bit set bought separately
Bit size, manual Technical data: 4 in; safety text: no more than 6 in bits Bit set ED52A610: 6 in and 10 in
Digging depth, maker’s figure Manual: 560 mm (about 22 in); product page: up to approximately 28 in No maximum printed in the manual text; it shows a 31.5 in single bit, 55.1 in with an extension rod the kit lacks
Weight, manual’s figure 12.8 kg (about 28 lb), basis not printed 10.4 kg (about 23 lb), basis not printed
Operators, manual Two handles gripped by the operator; no operator count printed Operator plus helper on the support handle for holes of 6 in or larger
Reverse, manual None described None described
Bystander distance, manual None printed Children and animals no nearer than 3 m (10 ft)
Warranty, household Not printed in the manual Manual prints both 18 months and 12 months

Two rows decide it: the power source, because it fixes where you can work, and the bits in the kit, because they fix what you can dig without another purchase.

What Each Kit Is and What Comes in the Box

The XtremepowerUS 85060 post hole digger is a plug-in unit. According to its manual, the box holds the auger, one bit, two bolts and two nuts, a hex spanner and the manual. The DC HOUSE earth auger, model ED52A610, is a gas power head on a looped handlebar frame. According to its manual, the box holds the power head with its handle and gear case, the manual and a fuel mixing bottle, and the bits are bought as a separate set; the product page sells the kit with 6 in and 10 in bits and says it arrives in more than one box. My review of the XtremepowerUS digger goes through the 85060 in more detail.

Full Shutdown Box

Shutdown before you clear or free the bit, change or attach the bit, free a stuck bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger. Never reach toward the bit while it turns, and never clear it or free it with the machine running. Corded electric auger: release the switch or trigger, wait until the bit has stopped completely, then unplug the auger from the outlet by the plug, not the cord. Before transport or storage, also let the motor cool. Gas auger: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire (a spark plug cap on some makes) and secure it away from the plug. Let the engine and muffler cool before you touch the bit or anything near the exhaust. Only then free a stuck bit or clear wrapped material, using only the method your manual specifies (gloves do not make grabbing sharp wire or cutting edges safe), and check the bit and guards for damage. Do not handle unidentified wire, cables or pipes. Do not use reverse or run the engine or motor to back the bit out unless your manual expressly authorizes it for this task, with both hands on the designated handles and everyone clear of the bit; complete the full shutdown again before any further hands-on work. Add every step your manual gives, in its order, and refit every guard and shield before you restart.

Fitting a bit is a hands-on job, so complete the full shutdown for your auger in the shutdown box above first. On the 85060 you slide the bit onto the output shaft, push the bolt through and lock it with the nut, and the manual says to remove any adjusting key or wrench before the tool is switched on. The DC HOUSE bit is secured in the socket with a pin and an R-pin.

Power: Plug-In Motor or Mixed-Fuel Engine

The two machines get their power in opposite ways, and that sets where each one can work and what you must manage around it. The 85060 needs a 110 V outlet; the DC HOUSE needs mixed fuel and open air. My comparison of WORX vs XtremepowerUS auger puts a battery pack against the same cord.

The XtremepowerUS 1500W electric post hole digger draws 10.9 amps at 110 V, according to its manual. The cover says 1500W, its package list says 1200W, and 10.9 amps at 110 V works out to about 1,200 watts, so I read it as a 1200 W class machine. The manual asks for an outdoor extension cord that is heavy enough for the current the tool draws; ask the maker for the gauge and length before a long run. Keep the cord away from the bit, never carry the auger by the cord, and never use it in rain or wet conditions. The tool must be grounded, and the manual forbids adapter plugs on it.

The DC HOUSE manual lists a 52 cc, 2-cycle engine with a maximum output of 1.3 kW at 7000 r/min. The manual’s own lines do not agree on the mix ratio, so use the ratio in your manual, confirm it with DC HOUSE before the first tank, and mix only as the manual says. My DC HOUSE auger review covers the 52cc gas model with its 6 in and 10 in bits.

Before refuelling, complete the full gas shutdown in the shutdown box above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled, and follow the manual’s rules on ignition sources, no smoking and spilled fuel. The manual rejects E85 and gasoline above 10% ethanol, and it says not to store the unit with fuel in its tank.

The gas unit also makes exhaust. Never start or run a gas auger indoors or in a garage or shed, even with the doors open. Start and run it outdoors: the exhaust contains deadly carbon monoxide, which has no color, taste or smell, and small engines have been shown to produce lethal levels in poorly ventilated spaces (1). Let the muffler and engine cool before you touch them.

Winner: the XtremepowerUS wherever an outlet is near, because there is no fuel to mix, age or store; the DC HOUSE wherever none is, because it carries its own power.

Bits and Digging Depth as Each Maker Prints Them

These figures are the makers’ own, and they are not what either machine does in your soil. A bit length is not a digging depth, and a bit diameter is not a promise of hole size, so I read each printed number only for what it says. For footing holes, my roundup of augers for deck footings covers seven gas, battery and corded machines.

The XtremepowerUS post hole digger manual lists a 4 in auger bit in its technical data and says the digger operates with no more than 6 in bits, while the product page describes a 6 in bit on a 3/4 in shaft. For depth, the manual prints a drilling depth of 560 mm, about 22 in, and the product page says up to approximately 28 in. I trust the manual and treat the product page as a claim. Do not fit a bigger bit on the XtremepowerUS auger, because the manual caps the size.

The DC HOUSE bit set ED52A610 is 6 in and 10 in. A manual illustration labels the single bit 31.5 in (80 cm) and shows 55.1 in with an extension rod, and this kit has no rod. That is bit length, not a maximum depth. I set the DC HOUSE against another 52cc kit in DC HOUSE and VEVOR augers.

Winner: none on depth, since the makers print different things. For bit choice, the DC HOUSE if you want two bit sizes in one kit as sold; the XtremepowerUS if you stay at or under the 6 in its manual allows.

Handles, Operators and Weight

Both machines use two handles, but their manuals describe the people differently, and the weights are printed without a basis, so they do not rank the machines.

The 85060 manual says to grip the two handles firmly with both hands and never mentions a helper, and it prints no one-person or two-person rule. The DC HOUSE manual describes an operator on the throttle handle and lower grip and a helper on the support handle, and it says holes of 6 in or larger may be easier with two people. Use the number of people your exact manual specifies. A second person needs to know the plan, hold the unit as the manual describes and stay clear of the bit, and both people stop when either calls a stop. Never operate the DC HOUSE with the handles above chest height, because the manual says you could lose control.

The 85060 manual lists 12.8 kg, about 28 lb, and the DC HOUSE manual lists 10.4 kg, about 23 lb. Neither prints whether the figure includes the bit, so I do not call either one lighter. Before you lift, load, carry or move either machine, complete the full shutdown in the shutdown box above, and never carry the corded unit by its cord. Digging with an auger is heavy, jarring work that twists your arms and back, so take breaks and stop when you are tired or your attention slips.

Winner: a tie, because the weights share no stated basis and the operator rules differ by manual.

Safety Before Either Auger Touches the Ground

Nothing here replaces your own manual, and no step below is optional. If you cannot finish the 811 process, neither machine is an option on that spot.

Call 811 First

An auger can strike a gas line, water line, electric cable, irrigation line or other buried service at the point where it digs down, causing electric shock, fire, explosion or damage to services. Striking buried utilities is a recognised safety risk and cost in excavation work, and simulation training for utility workers cut strikes in one study (2). According to PHMSA, every state runs a one-call notification center, and the call and the marking are free. The 85060 manual says the machine is not designed for work especially in an area with underground electric, gas, water or telephone lines, and the DC HOUSE manual says to beware of underground hazards. Neither manual names 811.

Buried Lines

Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm responses from every notified utility, including markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Follow state ticket-validity and tolerance-zone rules, preserve markings, and keep augers outside the required clearance area. Near marks, use careful hand digging or another locating method permitted by state rules and the utility; obey any stricter auger-manual prohibition. Arrange separate locating for private services that 811 does not cover (irrigation lines, cables). Do not dig where a service’s location remains uncertain, and do not switch to a larger machine to get around it. No augering depth above a buried service is safe.

Clear the Spot and Dress for It

Before you start, walk the spot and remove rocks, sticks, wire, hose, stakes and anything else the bit could catch or throw. Identify irrigation lines, drip lines, cables and sprinkler heads before you start, and take loose garden hoses out of the work area. Do not handle or move unidentified cables, pipes or utility lines: keep the auger away from them and contact the utility if their location is uncertain.

Wear safety glasses with side shields or goggles meeting your manual’s specification, including ANSI Z87.1 where required, and add a face shield where required. Wear hearing protection with gas engines and wherever your manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional protection your manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep hair, clothing, gloves, hands and feet away from moving parts.

The 85060 manual requires eye protection, says individual hearing protection must be worn where sound may exceed 85 dB(A), and asks for heavy-duty, non-slip gloves and sturdy boots with steel toes highly recommended. The DC HOUSE manual names eye protection meeting ANSI Z87.1 or CE requirements, recommends hearing protection whenever the unit is used, and asks for sturdy, no-slip rubber work gloves, long pants, long sleeves and sturdy non-skid shoes, with no shorts and no bare feet. Keep those gloves away from the bit and every moving part. Hearing loss runs deeper in workers who handle vibrating, loud engine tools than noise alone would predict (3), which is one more reason to wear ear protection on the gas unit from the first minute.

Bystanders, Slopes and Soil

Keep children, pets and other people out of the work area and at least the distance specified in your exact manual. The DC HOUSE manual says children and animals should come no nearer than 3 m (10 ft) while the unit is in use, and that is DC HOUSE’s own figure, not a safe distance. The 85060 manual prints no number, so keep everyone well clear of the work area, as it directs. With either machine, stop if anyone enters the work area. No distance makes a work area safe on its own, so keep watching it.

On a slope or uneven ground, slow down, keep firm footing and follow only the slope or footing rule in your own manual. The 85060 manual says normal operation is on level surfaces and warns against overreaching. The DC HOUSE manual says not to stand on slippery, uneven or unstable surfaces, not to work in odd positions or on ladders, and not to overreach. Neither prints a slope rule, so obtain guidance from the manufacturer before using either auger on a slope. Do not dig in frozen or rock-hard ground or in ground full of roots and stones: the bit can bind and the machine can twist or kick.

Binding, a Stuck Bit and the Wrist

If the bit hits a root, a rock or a buried object, it can bind and the machine can twist or kick. Keep firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. Release the throttle or trigger immediately if the bit binds or control is threatened, then complete the full shutdown in the shutdown box and inspect for damage before restarting.

A sudden torque reaction loads the wrist and forearm muscles hard in a lab simulation, even when the torque is a small share of a person’s strength (4), which is why a braced stance and a firm grip matter. Use reverse only where your manual authorizes it for your model; neither manual here describes one.

If the bit sticks in the hole or material wraps around it, do not force it and do not reach for the bit. Stop and complete the full shutdown in the shutdown box before touching or inspecting it. Use only the freeing or clearing method specified in your exact manual; the DC HOUSE manual’s troubleshooting line says to remove the bit from the hole and clear the hole of obstructions, and the 85060 manual prints no freeing method, so obtain manufacturer or qualified service guidance. Do not handle unidentified wire, cables or pipes.

Starting, Digging and Cleaning Up With Each One

Finish the 811 process and read the shutdown box above before you copy any of these moments, and treat none of them as a result for you to match.

The XtremepowerUS 85060

I start with the cord, not the trigger. I lay the outdoor-rated cord out behind me and clear of the bit’s path, because the manual asks for a cord that is suitable for outdoors and heavy enough for the current. The manual then says to set the auger upright on the drilling point, plant my feet stable and away from the bit, and grip both handles firmly. In gloved hands the two looped grips keep my elbows close to my sides, which is where I want them when the trigger goes in.

XtremepowerUS 85060 corded electric post hole digger with orange grips, held by both handles over garden soil
XtremepowerUS 85060 Corded Electric Post Hole Digger with 6-Inch Bit

SHOP ON AMAZON

I squeeze the trigger slowly, as the manual says, and press the handles lightly downward instead of leaning my body weight on the head. When the motor labors, the manual’s overload line says to lift the auger so the motor unloads and the soil can come up out of the hole, and I add one step of my own: after any stall I release the trigger, wait until the bit has stopped and complete the full shutdown in the shutdown box above before I look at anything.

Man gripping both handles of the XtremepowerUS corded post hole digger while its bit drills into garden soil
XtremepowerUS 85060 Corded Electric Post Hole Digger with 6-Inch Bit

SHOP ON AMAZON

Afterward, once I have completed the full shutdown for a corded unit in the shutdown box above, I wipe the housing with a soft cloth dampened with a mild soap and water mixture, as the manual says, and I keep ammonia, chlorine and abrasive cleaners away from it. Before I lift the machine back into the shed I complete the full shutdown in the shutdown box above again, and I never carry it by the cord.

The DC HOUSE 52cc

The DC HOUSE asks for a ritual, and I follow the manual’s order. Before I secure the bit in its socket with the pin and R-pin, I complete the full gas shutdown in the shutdown box above. Then, outdoors in open air, I set the choke for a cold start, move the power switch to I, press the purge bulb 7 to 8 times with the unit tilted so the bubble moves, and pull the starter with my left hand on the frame.

DC HOUSE 52cc gas earth auger with black and white engine, handlebar frame and 6 in and 10 in bits
DC HOUSE 52cc Gas Earth Auger with 6-Inch and 10-Inch Bits

SHOP ON AMAZON

The throttle trigger will not move until the lockout lever is engaged, so my thumb finds the lever before my finger finds the trigger. I wrap thumbs and fingers fully around both handles and keep them below chest height, as the manual asks. Standing the 6 in and 10 in bits side by side, I can see how much more soil the wider one has to move, which explains why the manual says a second person may help with holes of six inches or larger.

I put ear protection on before I pull the starter, since the manual recommends hearing protection whenever the unit is used, and I leave it on until the engine is off and the bit has stopped. If the bit sticks in a root, I release the throttle, complete the full gas shutdown, and then follow the manual’s one troubleshooting line, which is to remove the bit from the hole and clear the hole of obstructions. Before I empty the tank for storage I complete the full gas shutdown in the shutdown box above, because the manual says not to store the unit with fuel in it.

Choose the XtremepowerUS 85060 If

The 85060 suits a small, planned job close to a safe outdoor outlet, where you would rather unplug a cord than carry fuel.

  • You have an outdoor outlet near the spot: the machine runs on 110 V with no engine exhaust.
  • You want no fuel to mix or store: there is no mix ratio to confirm and no tank to empty.
  • You stay at or under 6 in: the manual says the digger operates with no more than 6 in bits.

What I like about the 85060 near the shed is that I can see the outlet it depends on. Skip it if your spot lies beyond a cord you can lay out and watch, or if your ground is excessively rocky.

SHOP ON AMAZON

Choose the DC HOUSE 52cc If

The DC HOUSE suits work beyond the reach of any outlet, and a buyer who wants two bit sizes in one kit.

  • No outlet reaches the spot: the engine carries its own power, outdoors only.
  • You want 6 in and 10 in bits together: the product page sells the kit that way, with no extension rod.
  • A helper is available: the manual describes a helper on the support handle for holes of 6 in or larger.

I read the helper lines aloud to whoever holds the support handle before the bit touches the ground. Skip it if you will not confirm the fuel mix with DC HOUSE, or if you want a single clear one-person rating, which the manual does not give. My roundup of one-person earth augers lists the models you can run alone.

SHOP ON AMAZON

Plug or Fuel Can: Settling on One

The ground decides this before the brand does. If an outdoor outlet sits near your holes, the 85060 asks for a cord, and the DC HOUSE asks for a fuel mix you must confirm with the maker. If your holes lie beyond any outlet, the 52cc is the one that goes there. Whichever you pick, the 811 process comes first and the full shutdown comes before every hands-on task, with ear and eye protection on from the first minute. With those rules in place, the XtremepowerUS vs DC HOUSE auger decision is simple: the 85060 for short jobs near an outlet, the 52cc for holes beyond the cord. My roundup of seven earth augers compares gas, corded and battery models.

Garden Power Scout Amazon Black Friday Banner

Frequently Asked Questions

Which is better, the XtremepowerUS 85060 or the DC HOUSE 52cc auger?

The better pick is the XtremepowerUS 85060 for a few holes within reach of an outdoor outlet, and the DC HOUSE 52cc auger where no outlet reaches or you want 6 in and 10 in bits together. Both manuals warn about buried lines, so finish the 811 process before either machine touches the ground.

What fuel mixture does the DC HOUSE 52cc auger need?

The DC HOUSE 52cc auger needs the 2-cycle gas and oil mixture printed in its manual, whose own lines on the ratio disagree, so confirm it with DC HOUSE first. Before refuelling, complete the full gas shutdown in the shutdown box above, then refuel outdoors on the ground with the engine cooled.

Can the DC HOUSE 52cc auger dig in rocky ground?

The DC HOUSE 52cc auger is not meant for rocky ground, because its manual says not to operate the unit in excessively rocky ground. If the bit binds on a root or rock, release the throttle, complete the full shutdown, and follow the manual’s troubleshooting line before the next hole.

Does the DC HOUSE 52cc auger have reverse?

The DC HOUSE 52cc auger has no reverse described in its manual, so do not count on one to free a stuck bit. Stop, complete the full shutdown in the shutdown box, and clear the hole of obstructions as the manual directs, or ask DC HOUSE for qualified service guidance before you dig again.

How deep does the XtremepowerUS electric post hole digger dig?

The XtremepowerUS manual for item 85060 prints a drilling depth of 560 mm, about 22 in, while the product page says up to approximately 28 in. Treat both as maker figures rather than results in your soil, never choose a bit or depth by chasing them, and finish the 811 process before any hole is started.

References

  1. Hyson BE, Friedman BM, Spear B, Bishop-Freeman SC. Lethal carbon monoxide generated from small internal combustion engines. J Anal Toxicol. 2024;48(8):625-629.
  2. Gallagher AG, Hart M, Cleary D, et al. Proficiency based progression simulation training significantly reduces utility strikes: a prospective, randomized and blinded study. PLoS One. 2020;15(5):e0231979.
  3. Thaper R, Sesek R, Garnett R, Acosta-Sojo Y, Purdy GT. The combined impact of hand-arm vibration and noise exposure on hearing sensitivity of agricultural/forestry workers: a systematic literature review. Int J Environ Res Public Health. 2023;20(5):4276.
  4. Armstrong T, Bir C, Foulke J, Martin B, Finsen L, Sjogaard G. Muscle responses to simulated torque reactions of hand-held power tools. Ergonomics. 1999;42(1):146-159.

Safety Note: Only an adult who has read the manual and understands the controls should use an earth auger or post hole digger, never a child or anyone tired or impaired. Use the number of people your manual specifies, and keep everyone else out of the work area. The rotating bit can catch hair, clothing and gloves, and it can bind on a root, a rock or a buried object: the machine can then twist or kick in your hands. Stand with firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. If utility contact or a gas leak is suspected, stop work immediately. Do not touch, inspect, free or move the auger or exposed service, and do not attempt the normal hands-on shutdown or disconnect electrical connections in the suspected leak area. Leave the area, keep others away and contact the utility from a safe location; call 911 for a suspected gas leak or immediate danger. Otherwise, release the throttle or trigger immediately if the bit binds or control is threatened, then follow the shutdown procedure. On a two-person unit, both operators must understand the controls and agree on start and stop signals before starting; stop whenever either operator calls stop. Use reverse only where your manual expressly authorizes it. Never touch or clear the bit while it turns. Before you clear or free the bit, change or attach the bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger, complete the shutdown for its power type. Corded electric: release the switch or trigger, wait until the bit has stopped completely, then unplug it from the outlet by the plug, not the cord; before transport or storage, also let the motor cool. Battery: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where the model has one. Gas: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire and secure it away from the plug, and let the engine and muffler cool before touching the bit, engine, muffler or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown instructions in both the bit or attachment manual and the power-head or drill manual. If the bit sticks or material wraps around it, stop and complete the full shutdown before touching or inspecting it. Use only the freeing or clearing method specified in the exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when the exact manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. Wear safety glasses with side shields or goggles meeting the manual’s specification, including ANSI Z87.1 where required; add a face shield where required. Wear hearing protection with gas engines and wherever the manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional footwear protection the manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep them, clothing, hair, hands and feet away from moving parts. Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm that every notified utility has responded with markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Preserve the marks and follow your state’s ticket-validity and tolerance-zone rules. Keep the auger out of the required clearance area; near marks, use careful hand digging or another locating method permitted by state rules and the utility. Follow any stricter prohibition in the auger’s manual. Marks do not show a safe drilling depth. Arrange to locate private irrigation lines, cables and other services that 811 may not cover. If a line’s location remains uncertain, do not dig there. Do not handle or move unidentified cables, pipes or utility lines. Before you start, remove rocks, sticks, wire and loose hoses, and identify irrigation lines, drip lines and sprinkler heads. Keep children, pets and other people out of the work area and at least the distance your exact manual specifies. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs. No single distance is safe for every auger. On a slope or uneven ground, slow down, keep firm footing and follow only your manual’s rule. Do not dig in frozen or rock-hard ground. Before refuelling, complete the full gas shutdown described above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Keep fuel away from smoking, flames, sparks and other ignition sources. Use an approved fuel container, avoid overfilling, secure the cap and follow the manual’s spill-cleanup and restart-location instructions; do not start with a fuel leak. Use the specified fuel and oil arrangement for that engine. Never start or run a gas auger indoors, in a garage or shed, or in an enclosed or poorly ventilated area, even with doors open. Operate outdoors where exhaust cannot accumulate or enter occupied spaces through doors, windows or air intakes. Exhaust contains deadly carbon monoxide. For a corded auger, inspect the cord and extension cord before use and do not use damaged cords or plugs. Use an outdoor extension cord meeting the exact manual’s gauge, length, plug and grounding requirements, and follow its GFCI instructions. Keep connections dry and the cord clear of the bit, heat, oil and sharp edges. Never carry the auger by its cord or wrap the cord around your body. Do not use it in rain or wet conditions prohibited by the manual. Use only manufacturer-approved batteries and chargers for the exact model. Complete the battery shutdown before removing or changing a battery, and keep the switch off and fingers off the trigger when installing one. Do not use damaged or modified batteries or chargers. Keep loose battery terminals away from metal objects, and follow the battery and charger manuals for moisture exposure, charging temperature, cooling and storage. Load and unload only as your manual describes, and store the auger dry and out of children’s reach. Take breaks and stop when you are tired.

Scroll to Top