The best battery powered lawn edger cuts a clean lawn edge without a cord, a fuel can or a recoil pull. I used the seven below along the borders of my concrete work pad, the path to the house and the strips under the plum rows, and I say where each one falls short.
My top pick is the EGO Power+ ME0801 8-Inch Edger Attachment Kit, a kit with the battery and charger in the box. After the reviews I explain how to choose, what the battery really costs and the safety steps I follow every time.
Best Battery Powered Lawn Edger Reviews 2026: 7 Cordless Edgers I Put to Work
These seven are my picks for the best cordless edger for lawn borders: four kits with a battery and a charger in the box, and three tools sold without one. I ranked them on what is in the box, the blade and depth, the weight and what each edger asks of you. Every review says who should skip it.
1. EGO Power+ ME0801 8-Inch Edger Attachment Kit Best Overall
The EGO Power+ ME0801 is the cordless edger I recommend first to anyone who wants a complete kit and a tool that can do more than edge later. The box holds the 8 in edger attachment, the 56V power head, a 2.5Ah battery and a charger, so the first edge gets cut the day it arrives. According to EGO, the edger cuts up to 3 in deep, and the same power head takes other EGO attachments that you buy separately.
WHY I CHOSE THIS ✓
I put the ME0801 first because it is the complete way into a 56V system at a mid-range price: attachment, power head, battery and charger in one box, with a head that takes more EGO attachments later. It is the cordless edger I recommend for a quarter-acre lawn with a pad, a path and a few borders. The small pack is its weak point, and a second pack fixes that.
EGO Power+ ME0801 8-Inch Edger Attachment Kit Specs
Key Features:
- Variable-speed power head: you hold the lock-off, pull the trigger and set high or low speed with the switch on the head, so one pack covers a light pass and a harder cut.
- 8 in blade, up to 3 in deep: that is EGO’s maximum, and the manual asks you to set the blade so it just touches the ground or breaks the surface of the soil.
- Guide wheel on a depth bar: loosen one knob, slide the wheel along the bar and tighten it again once the blade has stopped and the battery is out, so depth is continuous and not stepped.
- Removable guide plate: EGO calls it an optional guide for cutting against pavement, and the manual shows how to take it off.
- Fixed blade guard and debris flap: the guard is set at the factory so its arrow and open side point away from you, and EGO says never to adjust it.
- Replaceable blade: the manual names the AEB0800 blade, says to replace a cracked or worn blade at once and forbids sharpening, straightening or welding it.
- One head for more tools: the edger works only on EGO’s own 56V power heads, and the same head takes other EGO attachments.
I set the depth with the battery out and checked it again in my working stance, because EGO says to set the blade so it just touches the ground or breaks the surface. Along the lawn edge beside the concrete work pad I let the guide wheel follow the edge and kept the blade clear of the concrete, which gave me a clean line. If the blade bogs down, EGO says you are going too fast, and I drop to a normal walking pace.
The pack is the part to weigh. EGO publishes no run time for this kit, and the 2.5Ah battery is a small one, so I plan a long edge in sections and start with a full charge. EGO lists 5.09 lb for the attachment, 5.82 lb for the power head and 2.77 lb for a 2.5Ah pack, which comes to about 13.7 lb with that pack by my sum, and along the whole border of the house lawn my forearms felt the difference between the empty tool and the full one.
The guide plate gave the kit a second job on the 4 ft concrete path to the house door. I keep it on beside the path, where it rides the paving, and I take it off along the tilled strip under the plum trees, where there is no hard edge to follow. The limit is gravel. EGO says not to use the edger on or near graveled surfaces, so the crushed-stone yard stays with a rake and a spade.
Switch off, wait for the blade to stop and take the battery out before you move the guide wheel, and edge on dry soil: EGO says wet soil or wet grass clogs the guard and leaves an uneven edge.
Wear eye protection with side shields marked ANSI Z87.1, hearing protection, heavy long pants, boots and gloves every time, and clear rocks, glass and wire from the edge first. EGO says visitors should be kept at a distance from the work area and gives no figure in feet for the edger, so I keep people and pets well back and stop the edger when anyone comes closer.
Before I touch the blade, clear the guard or change the attachment, I switch off, wait for the blade to stop and take the battery out, because EGO says battery tools are always in operating condition. Charge the pack between 41 and 104 F, store the tool indoors and dry with the battery removed, and call 811 before you cut a new edge into soil.
Buy it if you want one box that edges today and takes more EGO attachments later, and your edges are the lawn borders of a small to medium property. Skip it if your edge runs along gravel, if you want a stand-alone edger with no power head, or if you already own batteries from another maker.
FINAL VERDICT
Buy the ME0801 when you want everything in one box and room to add attachments. The small pack is the price of that simplicity, and a second pack answers it.
It is the complete cordless edger kit I recommend to most lawn owners.
2. DEWALT DCED472X1 60V MAX 7-1/2 Inch Edger Kit Best Premium
The DEWALT DCED472X1 is the edger kit I recommend when you want a wide 7-1/2 in blade on DEWALT’s 60V MAX FLEXVOLT platform. It is attachment capable: the edger goes on a powerhead that takes other DEWALT attachments, which you buy separately, and the kit includes the FLEXVOLT battery and the charger. It sits in the premium price tier, and much of that price is the platform.
WHY I CHOSE THIS ✓
I put the DEWALT second because it is the premium kit on the 60V MAX FLEXVOLT platform, with a hardened 7-1/2 in blade and a 3-year limited warranty. It is the premium pick for an owner who wants more than an edger out of one battery system. The price tier is real, so choose it for the platform as well as the edger.
DEWALT DCED472X1 60V MAX 7-1/2 Inch Edger Kit Specs
Key Features:
- 60V MAX FLEXVOLT battery: DEWALT says the FLEXVOLT pack is backwards compatible with its 20V MAX tools, so the kit battery can also run those tools.
- Brushless motor: DEWALT calls it professional grade and says it maximizes runtime, though it publishes no minutes.
- Variable trigger and HI/LO switch: the powerhead manual says LO extends runtime and HI shortens it, so you trade speed for minutes on the same pack.
- 7-1/2 in hardened steel blade: two wear indicators show when to replace it, and the manual recommends starting at the minimum depth to extend blade life.
- Large front wheel and a separate edge guide: the guide rests against the paved edge with the wheel on the pavement, which holds a straight line along a path.
- Auxiliary handle: one hand goes on the powerhead handle and one on the auxiliary handle, and the manual says never to use the pole as a gripping surface.
- Attachment-capable powerhead: it accepts other DEWALT attachments, and the edger attachment works only on DEWALT powerheads.
The edge guide is the part I noticed first. Lined up against the paved edge with the wheel on the pavement, it held a straight line along the 4 ft path to the house door without me steering the blade. DEWALT’s manual recommends 1 in of depth for edging and says to start at the minimum, and I keep the 2-1/2 in maximum for cutting a new border, where I make the depth deeper only after a shallow test pass.
To avoid kickback the manual says to tilt the handle down so the blade is above the ground, switch on, then raise the handle slowly to lower the blade. On the first edging of the season DEWALT says to move forward slowly because the grass is thickest then, and to back up an inch or two if the tool slows until the blade recovers speed. The powerhead manual says LO extends runtime and HI gives performance and shortens it.
A blade change shows what a premium kit expects from you. The wrench for the flange nut, 13 mm or 17 mm according to the manual, is not in the box, so I put one beside the charger before I needed it. The manual has you switch off, wait for the blade to stop and remove the battery, then work with gloves and eye protection, the tool on its side and the edger attachment off the powerhead, then lock the shaft with the rod and turn the nut clockwise to loosen it.
Never lock the trigger on, and let the blade stop before you put the tool down, because DEWALT says the blade rotates momentarily after the switch is released.
DEWALT asks for ANSI Z87.1 eye protection, ANSI S12.6 hearing protection and a dust mask where dust rises, and it says to keep bystanders and pets at least 100 ft away. Do not use it on wet grass or wet soil, and if the tool gets wet, DEWALT says to let it dry for at least 48 hours.
Store it with the battery removed, the guard cleaned and the tool hung by its handle, never by the trigger, and away from fertilizers and chemicals. DEWALT lists no weight or run time for this kit, so check the feel of the auxiliary handle and both grips before you commit. Noise and vibration figures are not listed either, so I wear hearing protection from the first squeeze and take a break along a long border. Other DEWALT attachments need their own manual and are bought separately, and DEWALT says the edger attachment works only with DEWALT powerheads, so check the fit before you add a second tool to the platform.
Choose it if you want a wide blade on the FLEXVOLT platform, or if your DEWALT 20V MAX tools can share the kit’s FLEXVOLT battery. Skip it if you want the lowest price, a published weight before you buy, or a stand-alone edger with nothing else attached to the platform.
FINAL VERDICT
Pick the DCED472X1 if the FLEXVOLT platform is the reason you are shopping. You pay for the system, and the wide blade, the edge guide and the 3-year limited warranty come with it.
It is the premium edger kit I pick for DEWALT battery owners.
3. Greenworks 40V 8-Inch Brushless Edger Kit Best Value
The Greenworks 40V ED40L410 is the edger kit I recommend when you want a brushless 8 in edger with the battery and charger in the box at the lowest price tier of the kits on this page. According to Greenworks, the 40V battery runs more than 75 tools in its line, so the pack is not locked to the edger. It is my value pick for small to medium lawn borders, and it asks for nothing beyond what is in the box.
WHY I CHOSE THIS ✓
I give the Greenworks the value label for complete battery kits: it has the lowest price tier of the kits with a battery and a charger in the box, a brushless motor and a 3-year warranty. It is the one I recommend to a lawn owner who wants a working kit and no platform commitment. Its weak spots are a modest maximum depth, a warranty that covers personal use only and no attachment option.
Greenworks 40V 8-Inch Brushless Edger Kit Specs
Key Features:
- Brushless 40V motor: the manual lists a no-load speed of 6,500 rpm, and a variable-speed trigger lets you ease into the cut.
- Tool-free depth knob: it sits on the front wheel assembly, and the manual says to set it until the blade barely touches the ground in your normal working posture.
- Front guide wheel: it rides the pavement edge, and the manual lists it as a replaceable part.
- Replaceable skid plate: the manual lists it as a wear part too, so a worn plate is a repair and not a new edger.
- Guard and heavy-duty trail shield: Greenworks lists the shield with the guard, so a guard covers the blade and the shield sits over the debris side.
- Battery and charger in the box: the kit pack is a 40V 4.0Ah battery, and Greenworks gives a charge time of 120 minutes with the included 2A charger.
- Auxiliary handle: the manual has the right hand on the rear handle at about hip height and the left on the front handle, with the edger held away from your body.
The manual says to set the depth so the blade barely touches the ground in a normal working posture, then to check it again standing up. Greenworks says dry grass gives the best result, and if the blade begins to bog down, you are edging too fast. On the thick turf of the first edging of spring it did bog, and the manual’s troubleshooting list, depth set too low or walking too fast, told me where to look.
Greenworks claims up to 60 minutes with the included battery and states no conditions, so I plan the work in sections: the pad, the path and the house lawn border, with the charger ready between them. A full recharge takes 120 minutes with the 2A charger, according to Greenworks. That figure sets my rhythm more than the minutes on the box, because the second half of a big job waits on the charger.
Weight is 9.59 lb without the battery, and Greenworks publishes no figure with it, so the edger gets heavier by the pack along a long border. The tool cuts straight up and down only, with no bevel and no attachment option, and Greenworks says plainly that its edgers are not attachment capable. On the packed-soil paths of the vegetable plot I cleared the wood-chip mulch back before I edged, since the blade throws whatever sits at the edge, and clearing loose material comes before any edging.
Stop the edger, wait for the motor to stop and take the battery out before you clear the guard, because Greenworks says wet soil and wet grass can clog it and leave an uneven edge.
Wear safety glasses with side shields marked ANSI Z87.1, because everyday glasses are not safety glasses, and keep all bystanders, children and pets at least 50 ft away; Greenworks warns that thrown objects can ricochet. Do not use the edger in rain or damp conditions.
The battery and charger are Greenworks BAF and CAF series, and the manual says to charge between 39 and 104 F. The warranty covers personal use only, so a landscaper should look elsewhere. Store the edger without the battery, away from garden chemicals and de-icing salts, and call 811 before you cut a new edge into the soil.
Pick it for a small to medium lawn border along a pad, a path or a bed, especially if you already own Greenworks 40V tools. Skip it if your edge runs along gravel, if the turf is thick and overgrown, or if you need an attachment or a commercial warranty.
FINAL VERDICT
The ED40L410 is where I send a lawn owner who wants a complete brushless kit and no platform commitment. The shallow maximum depth and the personal-use warranty are the limits to accept.
It is the budget-friendly edger kit I recommend for small and medium lawns.
4. EGO Power+ MHC1603 Multi-Head Combo Kit Best Trimmer Edger Combo
The EGO Power+ MHC1603 is the best cordless lawn trimmer edger for an owner who wants one 56V power head to run a string trimmer and an edger. The box holds the PH1420 power head, a 16 in string trimmer attachment, an 8 in carbon fiber edger attachment, a 4.0Ah battery and a charger. It sits in the premium price tier because you buy two tools.
WHY I CHOSE THIS ✓
I chose the MHC1603 for the owner who wants the trimmer and the edger from a single battery system. It is the combo kit I recommend for a lawn with fences, beds and a pad. The trade-off is weight.
EGO Power+ MHC1603 Multi-Head Combo Kit Specs
Key Features:
- Two attachments on one head: they couple by an arrow and a wing knob with the battery out.
- Low and high speed modes: the manual says low gives better control and longer run time per charge.
- Carbon fiber edger shaft: EGO lists a lifetime warranty on the shaft when you register within 90 days.
- 8 in blade, up to 3 in deep: a guide wheel on a depth bar and a removable guide plate set the cut.
- Variable-speed trigger with lock-off: you hold the lock-off before the trigger works.
On the house lawn I cut the borders with the edger, then swap to the 16 in trimmer for the places a blade cannot reach. The swap is blade stopped, battery out, arrows aligned, wing knob fully tightened, and EGO says to check that knob again while you work, which I do after the first few minutes. Low speed gave me the control for the pass along the work pad.
According to EGO, the edger runs up to 75 minutes on one charge on the low setting with the 4.0Ah pack, and the trimmer up to 45 minutes. EGO gives no minutes for high, so I keep high for a stubborn corner. By my sum of EGO’s part weights the kit is about 16 lb with a 4.87 lb BA2240 4.0Ah pack. I set its run time and handling against a gas kit in my MHC1603 against ECHO PAS-225VP comparison.
Keep the edger off gravel. EGO says wet soil clogs the guard, so edge on dry ground.
Wear eye protection with side shields marked ANSI Z87.1, hearing protection and heavy long pants, boots and gloves. EGO gives no distance in feet for the edger, so I keep people and pets well back and stop when anyone walks closer.
The power head stops when it or the battery runs hot and restarts below 152 F, according to EGO’s manual. Switch off, wait for the blade to stop and take the battery out before you change the attachment, clear the guard or touch the blade.
Choose it if you want one power head for trimming and edging along fences, beds and a pad. Skip it if you only need an edger, if your edges are gravel, or if your batteries come from another maker.
FINAL VERDICT
Reach for the MHC1603 when one 56V head has to trim and edge. Expect to carry more weight and pay for two tools, and in return you get EGO’s longest stated edger run time and a long tool warranty.
It is the one-head kit I recommend for a trimmer and an edger.
5. Greenworks 80V 8-Inch Brushless Edger, Tool Only Best High-Voltage
The Greenworks 80V ED80L00 is the high-voltage edger for an owner who already has Greenworks 80V batteries. The box holds the edger and nothing else: no battery and no charger. You still need the Greenworks 2901302 pack or another BAB-series pack, and the CAB801 charger or another CAB-series charger.
WHY I CHOSE THIS ✓
I rank the Greenworks 80V fifth because it is the only 80V edger here, with a 4-year warranty, while the pack and charger cost extra. It is the right edger for an owner who already holds 80V batteries.
Greenworks 80V 8-Inch Brushless Edger, Tool Only Specs
Key Features:
- 80V brushless motor: the manual lists a no-load speed of 7,000 rpm, and you pull back the lock-out button before the trigger works.
- Depth knob: loosen it and set the depth until the blade barely touches the ground in your normal working posture.
- Wheel and skid plate: the wheel rolls on the pavement side, and the manual lists both parts as replaceable.
- 8 in blade: a metal rod holds the blade while the supplied wrench loosens the nut.
- 4-year warranty: it covers the original purchaser for personal use, and rental or commercial use is excluded.
The label says thrown objects can ricochet, so before I edge I close the house windows that face the pad and park the car in the shed, since the manual keeps bystanders at least 50 ft away. Greenworks’s manual gives no cutting depth for this model, so set the depth as the manual describes, until the blade barely touches the ground.
Voltage names the battery system, and the pack’s amp-hours and the soil decide how long you edge. Greenworks publishes no run time and no weight with a pack, so the 10.1 lb figure is the tool alone. If the blade bogs down, Greenworks says you are edging too fast. I weigh the 40V and 80V systems in my Greenworks 40V vs 80V edger guide.
The manual says this edger is for driveways, sidewalks and similar edges, and not for hedges, shrubs, bushes or flowers, so keep it on lawn and hard edges. I list more edgers for hard edges in my picks of the best lawn edgers for driveways.
Wear safety glasses with side shields marked ANSI Z87.1, rubber gloves and substantial footwear, and keep the guard in place. Switch off, wait until the motor stops and remove the battery before you adjust the depth, change the blade or clear the guard.
Use only the Greenworks 2901302 or another BAB-series battery and a CAB-series charger, and charge between 39 and 104 F. Before the first edging of spring I check the wheel and the skid plate, which the manual lists as replaceable. For winter I store the battery as the manual says, up to a year at 32 to 73 F, and the edger without a battery.
It suits an owner of 80V Greenworks batteries who edges driveways, paths and lawn borders. Skip it if you have no 80V pack, if your edge is wet or stony, or if you need a published depth or run time before you buy.
FINAL VERDICT
The ED80L00 earns its place on a shelf that already holds 80V Greenworks batteries. Without a pack the system costs more, and the 4-year warranty and replaceable wheel and skid plate are what you keep.
It is the edger I recommend to owners of Greenworks 80V batteries.
6. RYOBI ONE+ 18V 9-Inch Cordless Edger, Tool Only Best Lightweight
The RYOBI ONE+ P2300BTL is the light, low-cost edger for an owner who already has 18V ONE+ batteries. The box holds the edger only, with no battery and no charger, so you need a RYOBI ONE+ 18V pack and its charger. At 7.3 lb without a battery, according to RYOBI, it is the lowest weight on this page that a maker states for the tool without a battery.
WHY I CHOSE THIS ✓
I rank the RYOBI sixth and give it the lightweight label: 7.3 lb without a battery is the lowest weight a maker states here, and the blade is a wide 9 in. It is the edger I recommend to an owner whose ONE+ batteries already sit on the shelf.
RYOBI ONE+ 18V 9-Inch Cordless Edger, Tool Only Specs
Key Features:
- 9 in blade: a flat blade with a wear-indicator hole, and the manual says to replace it when it wears down to that hole.
- Depth lever, 1/4 in to 1-1/2 in: lift it, move it for more or less depth and release it to lock.
- Front handle that turns 180 degrees: the manual says to adjust it downward for edging.
- ONE+ battery platform: according to RYOBI, one 18V system runs over 300 tools.
- Light tool: 7.3 lb on RYOBI’s page, without a battery, so add the pack you own.
The manual says to start with the depth at 1/2 in to 1 in and make a shallow test cut, then adjust,, and I do the same. Angling the handle downward, as the manual says for edging, puts my wrist in a straight line with the shaft. The lever stops at 1-1/2 in, so a heavy border takes two passes. For a thicker border, my best lawn edger for overgrown edges picks cover the heavier jobs.
A light tool is easy to carry and easy to over-trust. RYOBI publishes no run time, only extended runtime with a 2Ah pack, so I work in short sections with a second pack charged. If the blade bogs down, RYOBI says you are edging too fast, and on thick sod after rain the tool told me so before my hands did.
Check the blade nut before each use and replace a dull or worn blade, because RYOBI says never to sharpen it.
Wear eye protection with side shields marked ANSI Z87.1, heavy long pants, boots and gloves, and keep bystanders at least 50 ft away. RYOBI says not to use the edger on or near gravel, and after a blade strike you stop, disconnect the power and inspect the tool.
Switch off, wait for the blade to stop and remove the battery before you clear the blade or change it. Charge the pack between 50 and 100 F, according to RYOBI’s manual, and keep the tool indoors, dry and away from garden chemicals. I wipe soil off the guard at the end of the day, which keeps wet clippings from packing in.
It suits a lawn owner with ONE+ batteries and short, light edges. Skip it if you have no ONE+ pack, need a deep cut or a trench, edge along gravel, or use it commercially, because the warranty drops to 90 days.
FINAL VERDICT
The P2300BTL suits a ONE+ owner who wants a wide blade in the lightest tool. Shallow cutting depth and no run time figure are the limits, and a buyer with no pack pays for one.
It is the light edger I recommend to owners of RYOBI ONE+ batteries.
7. CRAFTSMAN V20 20V MAX Cordless Edger Trencher, Tool Only Best Edger Trencher
The CRAFTSMAN CMCED400B is the cordless lawn edger trencher on this page: its pull-up edge guide turns the tool from a sidewalk edger into a bed edger that can also cut a shallow trench. The box holds the edger and an edging blade, with no battery and no charger, so you need a CRAFTSMAN V20 pack and a CRAFTSMAN charger. It is a budget-tier tool for owners already on the V20 system.
WHY I CHOSE THIS ✓
I rank the CRAFTSMAN seventh and give it the edger trencher label: CRAFTSMAN sells it as an edger and trencher, and its manual has a trenching section and a pull-up guide for both jobs. It is for the owner who wants one V20 tool for a path and a bed.
CRAFTSMAN V20 20V MAX Cordless Edger Trencher, Tool Only Specs
Key Features:
- Pull-up edge guide: in the lower notch it rests on the paved edge, and in the upper notch it is raised for bed edges or trenching.
- Depth lever with three settings: the manual recommends 1.4 in for edging and says to set the depth only as deep as the job needs.
- Blade with two wear indicators: replace it when you reach them, and keep the first cut shallow to extend blade life.
- Hook storage: hang the edger by its handle on a hook, never by the trigger.
- Adjustable handles: the main handle pivots and the auxiliary handle moves on two buttons, so your front arm stays straight.
I run the edge guide down along the concrete path, where it rests on the paved edge with the wheel on the paving, and raise it to the upper notch along the strip border. The manual says the guide can interfere in hard soil or sod, and it dragged when I left it down in thick turf. Depth stays at the 1.4 in the manual recommends. I list more bed-border tools in my roundup of the best edgers for flower beds.
The start is the step to learn. To avoid kickback, tilt the handle down so the blade is above the ground, switch on, let the blade spin, then slowly lift the handle to lower it, as the manual says. Move forward slowly on the first edging of the season.
As a trencher it cuts a shallow slot only. Before trenching, the manual says to check for buried electrical cables, so I mark drip lines, call 811 and set the depth to the job. My picks of the best edger and trencher combos cover the shallow-slot jobs in more detail.
Wear safety glasses with side shields marked ANSI Z87.1, hearing protection and substantial footwear, and keep bystanders and pets at least 100 ft away. Work away from a wall, steps or a stone, because the blade can rebound off a solid object.
Switch off, wait for the blade to stop and take the battery out before you touch the blade, adjust the depth or clear a clog, and clear it with a stick and never by tapping the tool on the ground. Charge the pack between 40 and 104 F in a CRAFTSMAN charger, and edge only dry grass and soil.
It suits a V20 owner who edges a path and cuts bed borders with one tool. Skip it if you have no V20 pack, want a published blade size, weight or run time, or have hard clay or sod.
FINAL VERDICT
Take the CMCED400B if your battery shelf says V20 and you edge a path and cut a bed. The missing blade size, weight and run time are the cost of the budget tier.
It is the edger trencher I recommend to V20 owners with paths and beds.
How to Choose a Battery Powered Lawn Edger
Seven checks sort the best battery lawn edger from a poor fit. Start with the battery, because it decides what you pay and what else the system runs. Then check the format, the blade and depth, the guide, the weight, the run time and the safety steps in the manual of the edger you buy.
Battery Platform and What Is in the Box
A kit holds the battery and the charger, and a tool-only edger holds the edger and nothing else. A cordless lawn edger takes only its own maker’s packs and chargers, so follow the maker’s list of approved packs and tools, because the voltage on the label does not settle compatibility. I count the pack and the charger as part of the tool, and I read the pack list before I order. I show what a complete kit holds in my Greenworks 40V edger review.
| Format | In the box | What you still buy |
|---|---|---|
| Kit | Edger, battery and charger | Nothing for the first cut |
| Attachment kit | Edger attachment, power head, battery and charger | Other attachments, if you want them |
| Tool only | The edger, sometimes a blade | Battery and charger from the same maker |
Stick Edger or Edger Attachment
A stick edger is one tool built for edging. An edger attachment fits only the power heads its maker lists, so check the fit list before you order. A cordless lawn trimmer edger kit puts a string trimmer attachment and a blade edger attachment on one power head, and the two cut differently. I review one such kit in my EGO MHC1603 review.
- Stick edger: the motor, shaft and blade are one tool, and you carry it along the edge.
- Attachment kit: one power head and battery run the edger and other attachments of the same maker.
- Trimmer and edger kit: one head does the string trimming and the blade edging, and you swap the attachment only after the blade has stopped and the battery is out.
I like one head for two jobs on a lawn with fences and beds, and a single-purpose edger for a long straight border.
Blade Size and Cutting Depth
The blade is a flat steel blade that spins on edge in a vertical plane, and the depth you set decides how much soil it cuts. The edgers here carry blades from 7-1/2 in to 9 in, and one maker publishes no blade size. Makers print different depth figures, so read each one as that maker’s own.
| Figure | What the makers say |
|---|---|
| Depth for edging | From the blade just touching the ground to 1 in or 1.4 in, in the manuals that give a figure |
| Maximum depth | 1-1/2 in to 3 in; two of the seven publish no maximum |
| First cut of the season | A shallow test cut, then a second pass if you need more |
I start shallow along the pad and go deeper only on the strip border. Switch off, wait for the blade to stop and remove the battery before you set the depth, then check it again standing in your working position.
Pro Tip
Several manuals say to start with the blade clear of the ground, let it reach full speed, then lower it into the cut at a walking pace. If the blade bogs down, you are going too fast.
Guide Wheel and Edge Guide
A cordless lawn edger with wheels rolls on the pavement side and keeps the blade at a set height. The names differ by maker, so read what the manual of your edger calls each part.
- Guide wheel: it sets the depth and rides the ground or the pavement edge.
- Guide plate or edge guide: it rests against the paved edge so the blade follows a straight line. I used that guide on a straight walk when I reviewed the DeWalt 60V edger.
- Skid plate: it protects the housing and is a wear part in some manuals.
Let the wheel or edge guide follow the hard edge and keep the blade from striking the pavement. One manual says to work away from a wall, steps or a stone, because the blade can rebound off a solid object. I tested edgers that hold a clean line along paving in my best lawn edger for sidewalk picks.
Weight With and Without the Battery
Weight decides how long you can edge, and a figure means little without its basis. The best battery operated lawn edger for a long border is the one you can still lift and steer at the end of the edge. My best lightweight lawn edger picks start from that same weight check.
| Basis | What the makers say |
|---|---|
| Stated without the battery | 7.3 lb to 10.1 lb on three edgers |
| Attachment kits | Part weights listed separately: sums of about 11 lb without the battery, and about 14 lb and 16 lb with EGO’s 2.5Ah and 4.0Ah packs at their listed weights (my sums) |
| Not published | Two edgers list no weight |
I check the weight basis before I compare two tools, because a bare-tool figure and a with-battery figure are different numbers.
Run Time and Warranty
On a cordless electric lawn edger, run time depends on the pack’s amp-hours, the setting, the soil and the depth, so a maker’s minutes are a guide and not a promise.
- Run time: one maker states up to 75 minutes on low with a 4.0Ah pack, another states up to 60 minutes with no conditions, and the rest publish none.
- Warranty: the makers here give 3 to 5 years for personal use, and commercial or rental use is shorter or excluded, down to 90 days on one.
- Battery: two makers state 3 years for their kit packs.
Key Takeaway
Compare run time only on the same battery size and the same speed setting. A bigger pack buys minutes, and a low setting buys more of them.
Noise, Vibration and Safety Steps
Hearing protection goes on every time. In NIOSH personal sampling of 80 landscaping workers, noise and carbon monoxide exposure were significantly higher with fuel-powered blowers, string trimmers and chainsaws than with battery versions (1). NIOSH still recommends a limit of 85 dBA over an eight-hour day and halving the exposure time for each 3 dBA increase (2), and none of the seven makers lists a noise figure.
Gloves reduced hand vibration on grounds equipment in a laboratory study with two participants (3), and I wear them for the grip as well as for the blade edge.
An edger throws soil and stone. In US emergency department data on lawn trimmer injuries from 2000 to 2009, the eye accounted for 42.5 percent of injuries and most came from foreign objects (4). In a study of lawnmower eye injuries, about three quarters came from thrown projectiles such as grass, dirt and rocks, and only 2 percent of those were documented as involving eye protection (5). That is why eye protection with side coverage that meets ANSI Z87.1 goes on first.
- Switch off the edger.
- Wait until all movement has stopped.
- Remove the battery.
- Wear gloves, then adjust, clear or touch the blade.
Keep bystanders and pets at the distance your manual gives: 50 ft in some manuals and 100 ft in others, and EGO gives no figure in feet for its edger. I keep people well back and stop when anyone comes closer.
Call 811 before you cut a new edge or trench into soil. One Call centers exist to reduce the chance of damage to underground utilities (6). They cover public utilities, so I mark my own drip, sprinkler and lighting lines before I edge.
No Gravel, No Wet Ground
EGO and RYOBI say not to use the edger on or near gravel, and several manuals say not to edge wet grass or wet soil. Keep the guard on, never let the blade strike pavement or rocks on purpose, and use only the battery and charger your maker lists.
Kit or Tool Only and What the Battery Costs Across Seasons
A kit puts everything in one purchase. A tool-only edger costs less at the till, and the pack and the charger are the rest of the bill. The best cordless lawn edger with battery and charger in the box saves you the second purchase.
| Edger | In the box | Still to buy |
|---|---|---|
| EGO Power+ ME0801 | Edger attachment, 56V power head, 2.5Ah battery, charger | Nothing for the first cut |
| DEWALT DCED472X1 | Edger, powerhead, FLEXVOLT battery, charger | A 13 mm or 17 mm wrench for the blade nut |
| Greenworks 40V ED40L410 | Edger, 4.0Ah battery, 2A charger | Nothing for the first cut |
| EGO Power+ MHC1603 | Power head, trimmer and edger attachments, 4.0Ah battery, charger | Nothing for the first cut |
| Greenworks 80V ED80L00 | Edger only | 80V pack and CAB-series charger |
| RYOBI ONE+ P2300BTL | Edger only | ONE+ 18V pack and charger |
| CRAFTSMAN CMCED400B | Edger and an edging blade | V20 pack and CRAFTSMAN charger |
- You own the platform: the tool-only edger is the whole cost, and the pack you already charge for other tools does the work.
- You own nothing: add the pack and the charger to the tool and compare that total with a kit before you buy.
- You plan more tools: Greenworks says its 40V pack runs more than 75 tools, RYOBI says ONE+ runs over 300, and EGO’s power head takes other EGO attachments. I compare the two platforms in my EGO ME0801 vs Greenworks 40V lawn edger comparison.
I buy by the battery: the best battery edger for lawn work is the one whose pack I can use in the next tool.
My Overall Verdict
I ranked these seven on what is in the box, the blade and depth, the weight and what each edger asks of you, to find the best cordless lawn edger for a small to medium lawn. The top three suit three different owners. My DeWalt and EGO edger comparison looks at the DCED472X1 and ME0801 kits head to head.
1. EGO Power+ ME0801 8-Inch Edger Attachment Kit Best Overall
For a small to medium lawn border and a buyer who wants the battery, charger and power head in one box.
2. DEWALT DCED472X1 60V MAX 7-1/2 Inch Edger Kit Best Premium
For an owner who wants a 7-1/2 in blade and an edge guide on the DEWALT FLEXVOLT platform, with a battery that also runs DEWALT 20V MAX tools.
3. Greenworks 40V 8-Inch Brushless Edger Kit Best Value
For a lawn owner who wants a brushless 8 in edger with battery and charger in the lowest kit price tier.
Choose the battery platform first, then the format and the weight, and keep the safety steps from the manual of the edger you buy. A kit is the shortest road to a clean edge, and a tool-only edger is a good deal only when you already own the pack. For most lawn borders, the EGO ME0801 is the best battery powered lawn edger on this page. For corded and gas options as well, my best lawn edger picks cover all three power types.
Why EGO Power+ ME0801 8-Inch Edger Attachment Kit Might Be the Best Choice
I put the ME0801 first because it is a complete kit at a mid-range price with a 56V head that takes more attachments later. On the lawn edge beside the work pad it earned first place for simple depth control and a clean line.
The trade-off is the small 2.5Ah pack. EGO publishes no run time for this kit, so I edge a long border in sections, or I add a second pack. I cover that pack and the rest of the kit in my review of the EGO ME0801.
Here is what the ME0801 gives you:
✓ An 8 in blade that cuts up to 3 in deep, according to EGO.
✓ A guide wheel on a bar that sets the depth with one knob.
✓ A removable guide plate for cutting against pavement.
✓ A 56V power head that takes other EGO attachments.
✓ A battery and a charger in the box.
Frequently Asked Questions
What is the best battery powered lawn edger?
The best battery powered lawn edger for most lawn borders is the EGO Power+ ME0801, a kit that puts the edger attachment, a 56V power head, a battery and a charger in one box. Pick the edger by the battery you already own, because a tool-only edger on the wrong platform costs the price of a new pack.
Are battery-powered edgers any good?
Battery-powered edgers are good for lawn borders along a pad, a path or a bed, and they run without a cord, a fuel mix or a recoil pull. They fall short on run time, where makers publish few figures, and on a first cut through thick sod, so plan the work in sections and keep a second pack charged.
What is the best electric trimmer edger?
The best electric trimmer edger on this page is the EGO Power+ MHC1603, a cordless kit with a 16 in string trimmer attachment and an 8 in edger attachment on one 56V power head. It weighs about 11 lb before the battery, so choose it for two jobs and not for the longest edge.
What is the best tool to trim lawn edges?
The best tool to trim lawn edges along a hard edge is a battery stick edger, because its vertical blade cuts a straight slice where grass meets a pad, a path or a bed. A string trimmer turned on its side makes a different cut, so keep it for the places a blade cannot reach.
Which battery-powered lawn edger is the best in 2026?
The battery-powered lawn edger that is best in 2026 is the one that fits the battery system you already own, and a new buyer should start with the EGO ME0801 kit. Owners of Greenworks, RYOBI or CRAFTSMAN batteries save money with the matching tool, so check the maker’s list of approved packs first.
References
- Alexander BM, Graydon PS, Pena M, Feng HA, Beamer BR. Hazardous exposures and engineering controls in the landscaping services industry. Journal of Occupational and Environmental Hygiene. 2025;22(3):189-202.
- National Institute for Occupational Safety and Health. Noise-Induced Hearing Loss. Noise and Hearing Loss. Centers for Disease Control and Prevention; 2024.
- Oh J, Chen N, Boyd C. Laboratory evaluation of occupational exposure to hand-arm vibration (HAV) during grounds maintenance equipment operations. Ann Agric Environ Med. 2023;30(2):384-389.
- Leinert J, Griffin R, Blackburn J, McGwin G. The epidemiology of lawn trimmer injuries in the United States: 2000-2009. J Safety Res. 2012;43(2):137-139. doi:10.1016/j.jsr.2012.03.001
- Stange NR, Jennissen CA. Lawnmower-Related Eye Injuries in the U.S., 2004 to 2023. Am J Ophthalmol. 2025;277:7-16.
- Sturgill RE, Taylor TRB, Dadi GB, Al-Bayati AJ, Montes Victorio S. Review of One Call Operator Membership and Exemptions for State Departments of Transportation. Transportation Research Record: Journal of the Transportation Research Board. 2025;2679(1):1466-1479.
Safety Note: Read your manual first. An edger can throw stones, soil and other debris with force, so remove loose stones, glass, wire and other objects before you start, keep the blade guard in place, and never edge in or near gravel or let the blade strike pavement or rocks on purpose. Wear impact-rated eye protection with side coverage that meets ANSI Z87.1, hearing protection, gloves, long pants, close-fitting long sleeves and sturdy slip-resistant boots. Keep people and pets at least as far away as your manual says (50 feet in some manuals, 100 feet in others), and stop if anyone comes closer. Use only the blade your manual lists for your exact edger or attachment, and fit an attachment only to a power head its maker approves, with the coupling fully locked. Before each use, with the tool switched off, all movement stopped and the battery removed, the cord unplugged or the spark plug wire disconnected (a gas engine cooled), check the blade, its bolts and the guard, and replace a cracked, bent or badly worn blade as your manual says; never sharpen a blade unless that manual allows it. Start the tool in the position your manual shows, with the blade clear of the ground, and let it reach full speed before you ease it into the cut. The blade can push the tool sideways when it hits concrete, a stone or a root, so hold both handles, keep firm footing and never force the cut. After the blade strikes something or the tool starts to vibrate, switch it off, wait for all movement to stop, disconnect the power the same way and inspect it before you go on. Before you clear a jam, change depth, clean the tool, fit or remove an attachment, or inspect or replace the blade, stop the motor or shut off the engine, wait for all movement to stop, then remove the battery, unplug the cord or disconnect the spark plug wire. On a gas edger, releasing the blade control can leave the engine running, and a blade that turns at idle means the edger must not be used until it is repaired. An edger cuts into the soil: in the US, contact 811 before you edge or trench into soil, and mark sprinkler lines, drip lines, landscape lighting wire and other private lines, which 811 may not locate. Refuel a gas model outdoors with the engine off and cool, away from flames or sparks, and move as far from the fueling spot as your manual says before starting; start and run it outdoors only, never in a garage, shed or other closed space, even with the door open. For a battery model, use only the battery and charger approved for your tool, charge and store them within the temperature range in your manual, and never use a damaged or swollen pack. For a corded model, use an undamaged outdoor extension cord of the gauge and length your manual gives, plugged into a GFCI outlet, keep the cord clear of the blade, the wheels and your feet, and avoid wet conditions.