A man comparing an 8-inch and 12-inch auger bit beside a gas earth auger outdoors

8 Inch vs 12 Inch Auger Bit: Which Hole Size Fits Your Job Best

The 8 inch vs 12 inch auger bit choice comes down to hole width: an 8 inch bit digs a hole about 8 inches across, and a 12 inch bit digs one about 12 inches across. Your power head’s manual decides which bit you can fit, and the post or plant decides which width you need. I plan a hole the way I planned seed drill settings in crop production: from the size of what goes in, then the tool. Below I cover what the diameter changes, which sizes makers list, when each width fits a job and the safety steps before you swap a bit.

8 Inch vs 12 Inch Auger Bit: The Short Answer

I pick by the post or plant first and the power head second. An 8 inch bit makes a hole about 8 inches wide and comes with the Champion, Powermate and Earthquake models in the table below, including the model I cover in my Earthquake E43 gas auger review. A 12 inch bit makes a hole about 12 inches wide, and the bit lists for the Echo, Ryobi and EGO models in that table stop at 10 inches, or about 250 millimeters on the EGO. Confirm a 12 inch bit with your own maker before you buy one.

The Short Answer

An 8 inch bit digs a hole about 8 inches wide and a 12 inch bit about 12 inches wide. At the same depth the 12 inch hole holds about 2.25 times the soil of the 8 inch hole, from the geometry of a cylinder (12 squared divided by 8 squared). Your manual’s bit list decides what fits your machine.

What Bit Diameter Changes and What It Does Not

Bit diameter is the width of the flighting, the spiral steel that lifts soil, and the hole comes out about that wide. A 12 inch diameter auger bit makes a wider hole than an 8 inch one and tells you nothing about depth, digging speed or how a machine copes with hard ground. My guide on what an earth auger is lists the parts, types and uses.

Hole Width and the Soil You Lift Out

A round hole is a cylinder, so its volume grows with the square of its width. Take a hole 24 inches deep as an example, chosen only for the arithmetic: the 8 inch hole holds about 0.7 cubic feet and the 12 inch hole about 1.6. That is more than double the soil to lift out and to refill, and no digging time follows from it, because soil, roots and moisture decide the time. I run this sum on paper before a job, because the doubled refill changes how I plan the day. My guide to 8 and 10 inch bits shows how a smaller step up in width changes the job.

Soil in a round hole 24 inches deep, by bit width (example depth)
Bit width Hole volume Compared with 8 inch
8 inch About 0.7 cubic feet 1 times
12 inch About 1.6 cubic feet About 2.25 times

The soil still has to travel up the flighting. Ryobi tells you to lift the running auger slowly from the hole so the debris clears, and Echo says to raise the auger periodically for the same reason. A wider bit gives that job more soil each time. My explainer on how an earth auger works covers the power head, the bit and the torque.

Length and Extensions Set Depth

Bit length is not hole depth, and extensions change length without changing width. Earthquake lists 12 inch and 18 inch extensions for deeper holes, and EGO lists a 500 millimeter extension, which is about 20 inches. A 12 inch extension is therefore a different part from a 12 inch bit, and shoppers mix the two up.

Which Bit Sizes Makers List for Their Power Heads

Every power head takes the bits its maker lists, and the list sits in the manual. When I open a manual, I look for the bit list and the pin before anything else. The table shows the sizes six makers print for the models named, and each list belongs to that model and edition.

Bit sizes printed for six models
Maker Bit sizes printed
Echo EA-400 and EA-500, operator’s manual (2005 edition) 6, 8 and 10 inch earth augers, plus extensions
Ryobi RY40701, 40V hole auger 8 inch bit supplied, with a bit line of 4, 6, 8 and 10 inch
EGO EG0800E, 56V earth auger (Australia and New Zealand edition) 200 millimeter bit supplied, with bits of 100, 150, 200 and 250 millimeter
Champion 201092 and 200940, gas augers 8 inch bit
Powermate PEA438.1, 43cc gas auger 8 inch bit, with 6 inch listed
Earthquake E43, gas auger combo 8 inch by 36 inch bit, with 12 inch and 18 inch extensions

None of those lists includes a 12 inch earth auger bit for a handheld power head. A maker’s list belongs to its own models and editions, so read your own manual before you buy. A bit must also match the output shaft and the pin that locks it on: Earthquake prints a 7/8 inch output shaft with a 3/8 inch cross hole, Champion a 9.5 by 45 millimeter clevis pin, and Ryobi and EGO a locking pin with a clip. The right diameter can still be the wrong bit. A drill-driven option is different again, and I compare it in my guide to the garden auger drill bit.

Changing a Bit Takes a Full Shutdown

Fitting or removing any bit is hands-on work near a turning part, so it follows the full shutdown for your power type.

Shutdown Box

Shutdown before you clear or free the bit, change or attach the bit, free a stuck bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger. Never reach toward the bit while it turns, and never clear it or free it with the machine running. Corded electric auger: release the switch or trigger, wait until the bit has stopped completely, then unplug the auger from the outlet by the plug, not the cord. Before transport or storage, also let the motor cool. Battery auger: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where your model has one, and keep it away from the auger. Gas auger: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire (a spark plug cap on some makes) and secure it away from the plug. Let the engine and muffler cool before you touch the bit or anything near the exhaust. Only then free a stuck bit or clear wrapped material, using only the method your manual specifies (gloves do not make grabbing sharp wire or cutting edges safe), and check the bit and guards for damage. Do not handle unidentified wire, cables or pipes. Do not use reverse or run the engine or motor to back the bit out unless your manual expressly authorizes it for this task, with both hands on the designated handles and everyone clear of the bit; complete the full shutdown again before any further hands-on work. Add every step your manual gives, in its order, and refit every guard and shield before you restart.

When an 8 Inch Auger Bit Fits the Job

An 8 inch auger bit fits a job when the hole only has to hold the post or the plant with room around it. Extension services give hole widths for plants and depths for fence posts, and the width around a post depends on the fill you plan and on your fence plan. I cover the next size down in my guide to 6-inch and 8-inch auger bits.

Planting Holes and Root Balls

For trees and shrubs, Illinois Extension says to dig two to three times the width of the root ball, Colorado State says three times, and Maryland says at least twice as wide and no deeper than the root ball. As a width calculation only, two to three times gives a root ball of about 3 to 4 inches for an 8 inch earth auger bit hole and about 4 to 6 inches for a 12 inch hole. My roundup of the best augers for planting trees lists gas and battery picks for tree holes.

Diameter alone does not make a suitable planting hole: Colorado State asks for a saucer-shaped hole, Maryland says the sides should slope outwards, and an auger digs straight walls. The sources also differ on depth, with Maryland saying no deeper than the root ball and Colorado State saying one to two inches shallower than the root ball height, so the root ball is planted at or above grade.

Depth matters as much as width: in one field trial, planting 15 or 31 centimeters below grade killed half of the Yoshino cherries within two years while every tree planted at grade lived (1). Compaction around a planting hole also cuts aeration and water uptake and slows the growth of woody plants (2).

When a stone-fruit tree in my orchard needs replacing, I size the planting hole from the root ball before I think about any tool. I measure the thing going in, then I look at the bit. I also compare an earth auger and a shovel for a single hole in a separate guide.

Fence Posts, Gate Posts and Footings

Penn State Extension, writing about horse fence, gives a typical line post depth of 36 inches, and says corner and gate posts are about 25 percent larger in diameter and are often set to 48 inches. Posts in sandy or wet soil go deeper, and frost-heaving soil loosens posts set too shallow. Those figures belong to horse fence, so check them against your own fence type and frost depth. I treat them as a starting point for my own frost depth, never as a rule. For 4×4 posts, I compare nine gas, corded and battery machines in my roundup of the best augers for 4×4 posts.

A larger post needs a wider hole for the same fill, so a 12 inch post hole auger bit starts to make sense for a gate post. A line post that sits in an 8 inch hole with room for fill needs less than half the soil moved, and I recommend the smaller bit when it does the job. My roundup of the best augers for fence posts compares gas, corded and battery picks for line and gate posts.

When a 12 Inch Auger Bit Is Worth Asking About

A 12 inch hole earns its place when a job needs room: a heavy gate post, a post with a wide fill collar or a planting hole for a bigger root ball. The question to ask first is whether your power head is built for that bit, because the manuals in the table above stop at 10 inches. I keep 12 inch holes for jobs that truly need the room.

What a Wider Bit Asks of the Machine

A wider circle covers more ground, which gives the bit more chances to meet a root or a stone. When a bit binds, the machine can twist or kick, and that reaction loads the wrist. In a lab simulation of torque reactions on a tool handle, wrist muscle activity was very high even though the torque pulses were short (3). A scoping review of 40 publications found that assembly workers using handheld powered tightening tools face repeated handle reaction loads, with some studies linking them to physiological changes that point to a higher risk of musculoskeletal disorders (4).

Both studies concern tightening tools, not augers, so take them as the general point that a handle which kicks back loads the arm. I take that as a reason to keep a firm stance and to stop the moment a bit bites something.

When a job calls for many large holes or a wide bit that your manual does not list, the next step is a larger rental machine with its own manual or a professional. That advice never applies where a buried service’s location is uncertain: there, no auger is an option.

8 Inch vs 12 Inch Auger Bit: How to Choose

Complete every step in this order before you dig or fit a bit.

  1. Measure the post, or the root ball, and decide how much room the fill or the roots need around it.
  2. Read your power head’s manual for the bit sizes it lists and for the shaft and pin the bit needs.
  3. Start the 811 process for every planned hole before the bit goes in.
  4. Pick the smallest listed bit that leaves the room your plan needs.
  5. Complete the full shutdown for your power type in the shutdown box above before you fit the bit.

Stay with 8 inch when your manual lists it, the post has room for fill and the root ball is small. Skip 12 inch when your power head’s manual does not list it, or when an 8 inch hole already gives the width your post needs. In ground full of roots and stones, a wider bit covers more of it.

I rank the 8 inch vs 12 inch auger bit question as a fit problem first and a preference second. A bit that your machine does not list is the wrong bit at any width. I compare gas, corded and battery models to help you choose the best earth auger for your job.

Safety Before You Dig With Either Bit

An earth auger drives a rotating steel bit into the ground, and every step below applies to either width. Your exact manual takes precedence over general advice.

Gear, Site and Buried Lines

Wear safety glasses with side shields or goggles meeting your manual’s specification, including ANSI Z87.1 where required, and add a face shield where required. Wear hearing protection with gas engines and wherever your manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional protection your manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep hair, clothing, gloves, hands and feet away from moving parts.

Before you start, walk the spot and remove rocks, sticks, wire, hose, stakes and anything else the bit could catch or throw. Identify irrigation lines, drip lines, cables and sprinkler heads before you start, and take loose garden hoses out of the work area. Do not handle or move unidentified cables, pipes or utility lines: keep the auger away from them and contact the utility if their location is uncertain.

According to PHMSA, you contact 811 before digging, and the notice period differs by state. Include every planned hole in the locate request. Wait the required state notice period and confirm responses from every notified utility, including markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging.

Follow state ticket-validity and tolerance-zone rules, preserve markings, and keep augers outside the required clearance area. Near marks, use careful hand digging or another locating method permitted by state rules and the utility; obey any stricter auger-manual prohibition. Arrange separate locating for private services that 811 does not cover (irrigation lines, cables). Do not dig where a service’s location remains uncertain: no auger is an option there. Utility markings establish no safe augering depth. A UK training trial on utility workers describes damage to buried utilities as a considerable safety risk to workers and a substantial cost (5).

When the Bit Binds

If the bit hits a root, a rock or a buried object, it can bind and the machine can twist or kick. Keep firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. Release the throttle or trigger immediately if the bit binds or control is threatened, then complete the full shutdown in the shutdown box above and inspect for damage before restarting. Use reverse only where your manual authorizes it for your model.

What to Check Before You Buy or Swap a Bit

Three things settle the choice. Your manual’s bit list sets what fits, the post or root ball sets the width you need, and a call to 811 comes before any hole. After the full shutdown in the shutdown box above, wipe the soil off the flights and store bits off the shed floor so the steel stays dry. Read your power head’s manual next, then pick the smallest bit it lists that leaves the room your job needs, and the 8 inch vs 12 inch auger bit decision follows from your post, your soil and that list.

Frequently Asked Questions

What size auger for 4×4 fence post?

The right auger size for a 4×4 fence post is a bit that leaves room around the post for fill, and your fence plan or local code sets how much room. Measure the post, add the room your fill needs, then pick the closest bit your power head’s manual lists.

Is a 12 inch auger bit too big for a 4×4 post?

A 12 inch auger bit leaves a lot of room around a 4×4 post, and the hole holds about 2.25 times the soil of an 8 inch hole at the same depth. That extra width means more fill to place and more soil to lift, so keep it for a wide fill collar or a heavy post. Your power head must list a 12 inch bit before you fit one.

Is an 8 inch auger bit big enough for a fence post?

An 8 inch auger bit is big enough for a fence post when the hole leaves the room your fill and your fence plan call for around that post. Penn State Extension says corner and gate posts are about 25 percent larger in diameter than line posts, so a larger post may ask for a wider hole. Measure the post before you pick the bit.

How wide should a post hole be?

A post hole should be wide enough to hold the post with room to place fill around it, and your fence plan or local code sets the width. For a planting hole, Illinois Extension says two to three times the root ball width and Colorado State says three times. A deck footing follows the size and depth your building department sets.

What is the difference between an 8 inch and a 12 inch auger bit?

The difference between an 8 inch and a 12 inch auger bit is hole width: about 8 inches against about 12, which makes the 12 inch hole hold about 2.25 times the soil at the same depth. The Echo EA-400 and EA-500, Ryobi RY40701 and EGO EG0800E lists stop at 10 inches, so check that your manual lists a 12 inch bit before you buy one.

References

  1. Wells C, Townsend K, Caldwell J, Ham D, Smiley ET, Sherwood M. Effects of planting depth on landscape tree survival and girdling root formation. Arboric Urban For. 2006;32(6):305-311.
  2. Kozlowski TT. Soil compaction and growth of woody plants. Scand J For Res. 1999;14(6):596-619.
  3. Armstrong T, Bir C, Foulke J, Martin B, Finsen L, Sjogaard G. Muscle responses to simulated torque reactions of hand-held power tools. Ergonomics. 1999;42(1):146-159.
  4. Mazaheri A, Rose LM. Reaction load exposure from handheld powered tightening tools: a scoping review. Int J Ind Ergon. 2021;81:103061.
  5. Gallagher AG, Hart M, Cleary D, et al. Proficiency based progression simulation training significantly reduces utility strikes: a prospective, randomized and blinded study. PLoS One. 2020;15(5):e0231979.

Safety Note: Only an adult who has read the manual and understands the controls should use an earth auger or post hole digger, never a child or anyone tired or impaired. Use the number of people your manual specifies, and keep everyone else out of the work area. The rotating bit can catch hair, clothing and gloves, and it can bind on a root, a rock or a buried object: the machine can then twist or kick in your hands. Stand with firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. If utility contact or a gas leak is suspected, stop work immediately. Do not touch, inspect, free or move the auger or exposed service, and do not attempt the normal hands-on shutdown or disconnect electrical connections in the suspected leak area. Leave the area, keep others away and contact the utility from a safe location; call 911 for a suspected gas leak or immediate danger. Otherwise, release the throttle or trigger immediately if the bit binds or control is threatened, then follow the shutdown procedure. On a two-person unit, both operators must understand the controls and agree on start and stop signals before starting; stop whenever either operator calls stop. Use reverse only where your manual expressly authorizes it. Never touch or clear the bit while it turns. Before you clear or free the bit, change or attach the bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger, complete the shutdown for its power type. Corded electric: release the switch or trigger, wait until the bit has stopped completely, then unplug it from the outlet by the plug, not the cord; before transport or storage, also let the motor cool. Battery: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where the model has one. Gas: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire and secure it away from the plug, and let the engine and muffler cool before touching the bit, engine, muffler or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown instructions in both the bit or attachment manual and the power-head or drill manual. If the bit sticks or material wraps around it, stop and complete the full shutdown before touching or inspecting it. Use only the freeing or clearing method specified in the exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when the exact manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. Wear safety glasses with side shields or goggles meeting the manual’s specification, including ANSI Z87.1 where required; add a face shield where required. Wear hearing protection with gas engines and wherever the manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional footwear protection the manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep them, clothing, hair, hands and feet away from moving parts. Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm that every notified utility has responded with markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Preserve the marks and follow your state’s ticket-validity and tolerance-zone rules. Keep the auger out of the required clearance area; near marks, use careful hand digging or another locating method permitted by state rules and the utility. Follow any stricter prohibition in the auger’s manual. Marks do not show a safe drilling depth. Arrange to locate private irrigation lines, cables and other services that 811 may not cover. If a line’s location remains uncertain, do not dig there. Do not handle or move unidentified cables, pipes or utility lines. Before you start, remove rocks, sticks, wire and loose hoses, and identify irrigation lines, drip lines and sprinkler heads. Keep children, pets and other people out of the work area and at least the distance your exact manual specifies. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs. No single distance is safe for every auger. On a slope or uneven ground, slow down, keep firm footing and follow only your manual’s rule. Do not dig in frozen or rock-hard ground. Before refuelling, complete the full gas shutdown described above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Keep fuel away from smoking, flames, sparks and other ignition sources. Use an approved fuel container, avoid overfilling, secure the cap and follow the manual’s spill-cleanup and restart-location instructions; do not start with a fuel leak. Use the specified fuel and oil arrangement for that engine. Never start or run a gas auger indoors, in a garage or shed, or in an enclosed or poorly ventilated area, even with doors open. Operate outdoors where exhaust cannot accumulate or enter occupied spaces through doors, windows or air intakes. Exhaust contains deadly carbon monoxide. For a corded auger, inspect the cord and extension cord before use and do not use damaged cords or plugs. Use an outdoor extension cord meeting the exact manual’s gauge, length, plug and grounding requirements, and follow its GFCI instructions. Keep connections dry and the cord clear of the bit, heat, oil and sharp edges. Never carry the auger by its cord or wrap the cord around your body. Do not use it in rain or wet conditions prohibited by the manual. Use only manufacturer-approved batteries and chargers for the exact model. Complete the battery shutdown before removing or changing a battery, and keep the switch off and fingers off the trigger when installing one. Do not use damaged or modified batteries or chargers. Keep loose battery terminals away from metal objects, and follow the battery and charger manuals for moisture exposure, charging temperature, cooling and storage. Load and unload only as your manual describes, and store the auger dry and out of children’s reach. Take breaks and stop when you are tired.

Scroll to Top