An earth auger is a power tool that drives a spiral steel bit into the ground to cut a round hole for a post, a plant or a stake. A motor or engine turns the bit, and the spiral lifts the loosened soil up the shaft. I run a 3.7-acre apricot and plum orchard, so I know how many holes a farm needs, and I know why the machine is also a hazard. This guide covers the parts, the power types, the jobs and the safety rules.
What Is an Earth Auger? The Short Answer
Think of it as a drill for soil. The power head holds the engine or motor, a gearbox and the handles. The bit screws into the ground, and the operator lets it pull itself down while keeping both hands on the handles. My explainer on how an earth auger works walks through the power head, the bit and the torque.
Makers use several names for the same kind of machine. Ryobi’s bit sheet calls its tool a hole auger, and Makita calls its tool a cordless earth auger. Sellers such as VEVOR list a gas model as a post hole digger, and you will see the same machine sold as an earth auger post hole digger. A hand-operated post hole digger has two handles and no motor, and a separate guide covers that class.
An earth auger makes round holes quickly in workable soil, with a machine that can twist in your hands. I recommend one when you have several holes of the same size to make, and a hand tool when you have one or two. The rest of this guide gives you the detail to decide.
The Parts of an Earth Auger
Every earth auger machine has the same few parts, whether it burns fuel or runs on a battery. Knowing the names helps you read a manual and spot a worn part.
The Power Head
The power head is the engine or motor with its gearbox and handles. Echo describes its gas power head as holding the engine, clutch, fuel system, ignition system, recoil starter and auger gear case. Makers print gear reduction ratios of about 30 to 1 on several gas heads, which slows the engine and raises the twisting force at the bit. Two-person machines add a second handle position, which I cover below.
The Earth Auger Bit
The bit is a spiral of steel flighting on a shaft. On Champion’s models the tip is a replaceable fishtail bit point that starts the hole. Ryobi and EGO join the bit to the power head with a locking pin and a clip, and Champion uses a clevis pin.
Bit diameter sets the hole diameter, and Echo lists 6, 8 and 10 inch bits, Ryobi’s bit line runs from 4 to 10 inches, and EGO lists bits from 100 to 250 millimeters. Bit length is a different figure from hole depth, so never read one as the other. Ryobi, EGO, Powermate and Makita all say to replace a cracked, bent or damaged bit. Fit or remove a bit only after the full shutdown in the safety section below. My comparison of 6-inch and 8-inch auger bits shows how each hole size suits a job.
Extensions
An extension is a rod that lengthens the bit for a deeper hole. EGO lists a 500 millimeter extension, Echo’s manual describes sliding one onto the auger shaft, and Earthquake offers 12 and 18 inch rods. Each maker states its own pin and fit, so use only the extension your manual names.
Gas, Cordless and Electric Earth Augers
The power source changes how a powered earth auger starts, how heavy it is, what you service and where you can run it. Another guide compares the power types head to head, so this section only describes each one.
Gas Earth Auger
A gas earth auger uses a small 2-stroke or 4-stroke engine. A 2-stroke engine runs on fuel mixed with oil. Champion’s 200940, Powermate’s PEA438.1 and Echo’s EA-400 print 50 to 1, and VEVOR’s D43-F prints 40 to 1, so the ratio belongs to your exact manual. Champion’s 4-stroke manual instead gives an engine oil capacity and a break-in period. Powermate and Champion warn against mixing fuel in the tool’s own tank. For the engine choice, I set fuel, oil, weight and upkeep side by side in 2-stroke and 4-stroke earth augers.
A gas auger runs only outdoors. Its exhaust holds carbon monoxide, and small engines have caused deadly carbon monoxide cases in poorly ventilated spaces (1). Hearing protection is part of the kit too. Workers who face both hand-arm vibration and noise show more hearing loss than workers exposed to noise alone (2).
Cordless Earth Auger
A cordless earth auger runs on a battery pack. Ryobi’s RY40701 is a 40 volt brushless model with forward high, forward low and reverse, and EGO’s EG0800E (Australia and New Zealand edition) is a 56 volt model with forward low, forward high and reverse. Makita’s DG001G is a small-bit tool: its manual prints a capacity of 60 millimeters on high speed, 200 millimeters in sandy soil on low speed and 150 millimeters in clay soil on low speed. Capacity, voltage and speed are the maker’s figures for that model and never a promise of what the tool does in your ground. My look at brushed and brushless earth augers explains how the two motors differ.
Electric Earth Auger
An electric earth auger in the corded sense plugs into an outlet and runs through an extension cord. It has no fuel, no pull cord and no battery to charge. It does bring cord rules. Use an outdoor extension cord that meets your exact manual’s requirements for gauge, length, plug type and grounding. Keep the cord away from the bit, never carry the auger by the cord, and never use it in the rain. Follow your exact manual’s instructions for cord routing, disconnecting the plug, keeping connections dry and GFCI protection. I compare the plug-in and battery types in my guide to corded and cordless earth augers.
What an Earth Auger Is Used For
Makers list planting and light post work. Ryobi lists planting trees, shrubs and flowers, cultivating and preparing soil, and digging for light duty fencing and posts. Those lists are a good guide to the machine’s real job: many round holes of one diameter.
- Planting holes: shrubs, bulbs and small trees. On our farm the orchard I planted in 2016 will need an occasional replacement tree, which is the kind of job a planting hole serves. If tree holes are your job, my roundup of augers for planting trees lists the models I compare.
- Posts and stakes: line posts, tree stakes and the end posts of a wire run. Gate and corner posts go deeper than line posts, since Penn State Extension gives about 36 inches for a typical line post and often 48 inches for corner and gate posts on a horse fence page.
- Small footings: a deck or platform footing. Local code decides the depth and size. As one example, the City of Blaine, Minnesota, handout for decks, porches and ramps asks for footings at least 42 inches below grade for frost, and your own building department sets your rule. For footing holes, my roundup of augers for deck footings lists the augers I compare.
- Supports in a garden bed: a tall bean pole or a tomato stake. For one stake I reach for a hand tool, not a machine.
Large jobs are beyond a homeowner machine. A long fence line, many large bits or hard clay and rock call for a larger rental machine with its own manual, or for a professional. A rental is never a way around an unmarked buried line, and the safety section explains why. I compare an earth auger with a tractor post hole digger to help you choose for a fence job.
How an Earth Auger Differs From Other Tools
Several tools get confused with it, so here is the short version of each.
- Drill-driven auger bit: a bit with no motor of its own. It needs a drill or power head with its own manual, and I treat it as an accessory, not as a machine. I compare a garden auger drill bit with an earth auger to explain which suits the hole you need.
- Manual earth auger or post hole digger: a hand tool that you twist or hinge by arm strength. It makes one hole slowly and costs no fuel.
- Tractor post hole digger and skid steer auger: implements for a tractor or loader. This guide gives no operating steps for them.
- Tiller: it works the top layer of soil in a bed. It does not bore a vertical hole. I explain the earth auger and tiller differences so you can choose a tool for holes or beds.
- Ice auger: it drills holes in ice. EGO’s manual excerpt for its EG0800 family lists ice bits as an accessory next to its earth bits.
How Wide and How Deep a Hole Can It Make
The bit sets the width, and the maker’s printed figures set the ceiling for depth. For the Ryobi RY40701, the spec list prints a maximum hole depth of 31 inches and the text recommends about 24 inches. For the EGO EG0800E (Australia and New Zealand edition), the manual prints a maximum drilling depth of 800 millimeters with its 200 millimeter bit. Treat each as the maker’s limit for that model and bit, never as a depth you will reach in hard soil.
Planting is where width and depth matter most.
For a tree or shrub, Maryland Extension says the hole should be no deeper than the root ball and at least twice as wide. Illinois Extension says no deeper than the root ball and two to three times as wide. Colorado State Extension says three times as wide and one to two inches shallower than the height of the root ball. That makes the example simple: a 12 inch root ball calls for a hole 24 to 36 inches wide. Depth matters just as much. In one trial, Yoshino cherry trees planted 15 or 31 centimeters below grade lost half their number within two years, while every tree planted at grade lived (3).
A bored hole is a straight-sided cylinder. Colorado State asks gardeners for a saucer-shaped hole and Maryland asks for sloping sides, and both say the root ball should sit on undisturbed soil. Follow those planting rules first, and ask whether a straight-sided bored hole can meet them before you reach for a machine. Compacted soil also holds back root growth and water uptake in woody plants (4), which is one more reason to follow the planting guide for your tree.
For posts, the sources give depth by post type and soil. Penn State says sandy or wet soil calls for deeper posts, and frost can heave posts that are set too shallow. The width of a post hole depends on the post and the fence type, so I give no single number. My roundup of augers for fence posts lists the models I compare for a post line.
Safety Before You Dig
An earth auger turns a steel bit that screws into the ground. It can bind on a root, a rock or a buried object, and then the machine can twist or kick in your hands. The bit can also catch hair, clothing and gloves, and a gas engine adds carbon monoxide. Nobody should run this tool without first reading the manual for that exact model.
Call 811 First
Contact 811 before digging and include every planned hole in the locate request.
Wait the required state notice period and confirm responses from every notified utility, including markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Follow state ticket-validity and tolerance-zone rules, preserve markings, and keep augers outside the required clearance area. Near marks, use careful hand digging or another locating method permitted by state rules and the utility; obey any stricter auger-manual prohibition. Arrange separate locating for private services that 811 does not cover (irrigation lines, cables). Do not dig where a service’s location remains uncertain, and never use a larger machine as a workaround. Never assume a safe augering depth above a buried service.
PHMSA says every state runs a one-call center and that the call is free, and it gives 48 to 72 hours as the typical notice. State law sets the exact period, so check yours. Careful practice cuts utility strikes in trained crews (5). On our farm I built the drip irrigation, so I know how many lines run through a few feet of ground, and I tell every reader the same thing: the call comes first.
Binding and Torque Reaction
If the bit hits a root, a rock or a buried object, it can bind and the machine can twist or kick. Keep firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft.
Never wrap the power cord around your hand, arm or body. Release the throttle or trigger immediately if the bit binds or control is threatened, then complete the full shutdown in the shutdown box below and inspect for damage before restarting. Use reverse only where your manual authorizes it for your model.
In a lab test of simulated torque reactions, wrist muscle activity was very high even when the pulses were short and the peak loads low (6). At a car plant, the force at the tool handle, not the rated torque alone, tracked with upper limb injuries (7). Both studies measured other tools and other workers, so I read them as a reason to brace and grip, not as a number for your yard.
Protective Gear, Bystanders and the Ground
Wear safety glasses with side shields or goggles meeting your manual’s specification, including ANSI Z87.1 where required, and add a face shield where required. Wear hearing protection with gas engines and wherever your manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional protection your manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep hair, clothing, gloves, hands and feet away from moving parts.
Key Point
Eye, ear, hand and foot protection come before the first start, every time.
Before you start, walk the spot and remove rocks, sticks, wire, hose, stakes and anything else the bit could catch or throw. Identify irrigation lines, drip lines, cables and sprinkler heads before you start, and take loose garden hoses out of the work area. Do not handle or move unidentified cables, pipes or utility lines: keep the auger away from them and contact the utility if their location is uncertain.
Keep children, pets and other people out of the work area and at least the distance specified in your exact manual. Stop if anyone enters that area.
If your manual gives no number, keep everyone well clear of the work area as it directs, and stop if anyone approaches. No distance makes a work area safe on its own: keep watching it. The printed figures differ by maker: The Ryobi RY40701 manual says at least 50 feet, the Champion 201092 and 200940 manuals and the Powermate PEA438.1 manual say at least 50 feet (15 meters), and the Echo EA-400 and EA-500 manual (2005 edition) says 3 meters (10 feet). Use the figure in your own manual.
Do not dig in frozen or rock-hard ground or in ground full of roots and stones: the bit can bind and the machine can twist or kick. On a slope or uneven ground, slow down, keep firm footing and follow only the slope or footing rule in your own manual. If your manual gives no such instruction, obtain guidance from the manufacturer before using the auger on a slope.
Never Run a Gas Auger Indoors
Never start or run a gas auger indoors or in a garage or shed, even with the doors open. Start and run it outdoors: the exhaust contains deadly carbon monoxide, which has no color, taste or smell. Allow the muffler and engine to cool before touching them.
Before refuelling, complete the full gas shutdown in the shutdown box below. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled, and mix fuel and oil only as the exact manual says.
Suspected Utility Contact
If you suspect the auger has touched a utility, do not touch, inspect, free or move the auger, the bit or any exposed service, and do not disconnect any plug, battery or wire near the spot. Walk away, keep others away, and contact the utility or emergency services from a safe place. The shutdown box below is for ordinary jams and servicing, not for a suspected strike.
The Full Shutdown
Every hands-on task starts here. This box covers every power type in this guide.
Full Shutdown Box
Shutdown before you clear or free the bit, change or attach the bit, free a stuck bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger. Never reach toward the bit while it turns, and never clear it or free it with the machine running.
- Corded electric auger: release the switch or trigger, wait until the bit has stopped completely, then unplug the auger from the outlet by the plug, not the cord. Before transport or storage, also let the motor cool.
- Battery auger: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where your model has one, and keep it away from the auger.
- Gas auger: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire (a spark plug cap on some makes) and secure it away from the plug. Let the engine and muffler cool before you touch the bit or anything near the exhaust.
- Drill-driven bit or any attachment system: follow the shutdown and isolation instructions in both the bit or attachment manual and the power-head or drill manual (a gas power head needs its own manual’s full shutdown).
- Then, and only then: free a stuck bit or clear wrapped material, using only the method your manual specifies (gloves do not make grabbing sharp wire or cutting edges safe), and check the bit and guards for damage. Do not handle unidentified wire, cables or pipes. Do not use reverse or run the engine or motor to back the bit out unless your manual expressly authorizes it for this task, with both hands on the designated handles and everyone clear of the bit; complete the full shutdown again before any further hands-on work. Add every step your manual gives, in its order, and refit every guard and shield before you restart.
If the bit sticks in the hole or material wraps around it, do not force it and do not reach for the bit. Stop and complete the full shutdown in the shutdown box above before touching or inspecting it. After a bind, a kick or a motor that cuts out, stop, complete the full shutdown and inspect before you go on.
Use only manufacturer-approved batteries and chargers for the exact model.
Before changing a battery or doing hands-on work, complete the full shutdown in the shutdown box above. Keep the switch off and fingers off the trigger when installing a battery. Do not use damaged or modified batteries or chargers. Protect loose battery terminals from contact with metal objects. Follow the battery and charger manuals for moisture exposure, charging temperature, cooling and storage.
Before you lift, load, carry or move the auger, complete the full shutdown in the shutdown box above. Load and unload only as your manual describes, never carry the auger by its cord, and refuel a gas unit on the ground, not in the truck bed. Follow the manual’s lifting and handling instructions.
Digging with an auger is heavy, jarring work that twists your arms and back. Take breaks, stop when you are tired or your attention slips, and use the gloves your manual recommends.
One Person or Two
Use the number of people your exact manual specifies. A two-person unit needs a second person who knows the plan, holds the unit as the manual describes and stays clear of the bit, and both people stop when either calls a stop. A one-person unit is operated by one person; never add a helper to a hand-held unit unless the manual says so. The Echo EA-400 and EA-500 manual (2005 edition), for example, says holes six inches or wider may be easier if two people hold the handles on opposite sides. My guide to one-person and two-person augers explains what makers print about operator counts.
Is an Earth Auger the Right Tool for You
Match the tool to the job, not the other way round. An earth auger fits a property owner with a handful of same-size holes, ground that is workable and marked, and a willingness to read the manual before the first start.
- Choose an earth auger for a row of planting holes or a line of posts in ground that is clear of roots and stones.
- Choose a hand tool for one or two holes, a stake in a vegetable bed or ground you cannot clear. I compare a manual post hole digger with an earth auger by job size and soil.
- Choose a larger rental machine or a professional for many holes, large bits, hard clay or rock, once every notified utility has responded and every mark is clear.
- Choose to wait when frozen ground, an unmarked line or a missing 811 response stands in the way.
Gas suits long runs of work and brings fuel, oil, exhaust and noise with it. A battery auger starts with a trigger and brings charging and storage rules. I lean to a cordless unit for planting holes near a house, since there is no fuel can to carry. My guide to battery or gas earth augers sets fuel and batteries side by side for digging jobs.
Pro Tip
Write down your hole diameter, your hole count and your soil before you shop. Those three facts narrow the choice faster than any spec sheet, and your manual’s limits then tell you whether the machine fits.
What to Remember Before You Pick One Up
Three things matter most. Call 811 and wait for every response before you dig. Hold the machine as the manual says, because the bit can bind. Finish the full shutdown before you touch the bit for any reason.
I recommend reading the safety pages of the manual twice before the first start. I skip the machine entirely when the ground is frozen or the marks are missing. Plan the layout first, with a stake at each hole, and read the whole manual for the exact model before the first start. Your next step is to read that manual for the model you are considering, then compare it against the jobs you listed. An earth auger earns its place when you have several holes of the same size to dig and a clear, marked patch of ground to dig them in. When you are ready to pick a model, my roundup covers seven earth augers I compare across gas, corded and battery options.
Frequently Asked Questions
What is an earth auger used for?
An earth auger is used to bore round holes for planting, posts and stakes. Makers list planting trees, shrubs and flowers, preparing soil and light duty fencing as typical jobs. Jobs with many holes, large bits or hard ground belong to larger rental machines or professionals.
What is the difference between an ice auger and an earth auger?
An earth auger bores holes in soil, and an ice auger bores holes in ice. EGO’s manual excerpt for its EG0800 family lists ice bits as an accessory next to its earth bits. Fit a bit only when both the power head manual and the bit’s own manual approve it.
What is another name for an auger?
Makers and sellers use several names for one machine. You will see hole auger, cordless earth auger, post hole auger and post hole digger. Check that a listing names a power head with its own motor or engine, because a bare bit is an accessory.
What is an auger used for in farming?
On a farm, an auger bores holes for planting trees and shrubs and for setting posts. Extension services give the width and depth for planting, and they give post depth by post type and soil. Large crew jobs call for a larger machine with its own manual.
What is an earth auger bit?
An earth auger bit is the spiral steel bit that screws into the ground and lifts the loosened soil. Ryobi, EGO and Champion join it to the power head with a pin, and Champion’s bit ends in a replaceable point. Bit diameter sets the hole diameter, and bit length is not the same as hole depth.
References
- Hyson BE, Friedman BM, Spear B, Bishop-Freeman SC. Lethal carbon monoxide generated from small internal combustion engines. J Anal Toxicol. 2024;48(8):625-629.
- Thaper R, Sesek R, Garnett R, Acosta-Sojo Y, Purdy GT. The combined impact of hand-arm vibration and noise exposure on hearing sensitivity of agricultural/forestry workers: a systematic literature review. Int J Environ Res Public Health. 2023;20(5):4276.
- Wells C, Townsend K, Caldwell J, Ham D, Smiley ET, Sherwood M. Effects of planting depth on landscape tree survival and girdling root formation. Arboric Urban For. 2006;32(6):305-311.
- Kozlowski TT. Soil compaction and growth of woody plants. Scand J For Res. 1999;14(6):596-619.
- Gallagher AG, Hart M, Cleary D, et al. Proficiency based progression simulation training significantly reduces utility strikes: a prospective, randomized and blinded study. PLoS One. 2020;15(5):e0231979.
- Armstrong T, Bir C, Foulke J, Martin B, Finsen L, Sjogaard G. Muscle responses to simulated torque reactions of hand-held power tools. Ergonomics. 1999;42(1):146-159.
- Ku CH, Radwin RG, Karsh BT. Power hand tool kinetics associated with upper limb injuries in an automobile assembly plant. J Occup Environ Hyg. 2007;4(6):391-399.
Safety Note: Only an adult who has read the manual and understands the controls should use an earth auger or post hole digger, never a child or anyone tired or impaired. Use the number of people your manual specifies, and keep everyone else out of the work area. The rotating bit can catch hair, clothing and gloves, and it can bind on a root, a rock or a buried object: the machine can then twist or kick in your hands. Stand with firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. If utility contact or a gas leak is suspected, stop work immediately. Do not touch, inspect, free or move the auger or exposed service, and do not attempt the normal hands-on shutdown or disconnect electrical connections in the suspected leak area. Leave the area, keep others away and contact the utility from a safe location; call 911 for a suspected gas leak or immediate danger. Otherwise, release the throttle or trigger immediately if the bit binds or control is threatened, then follow the shutdown procedure. On a two-person unit, both operators must understand the controls and agree on start and stop signals before starting; stop whenever either operator calls stop. Use reverse only where your manual expressly authorizes it. Never touch or clear the bit while it turns. Before you clear or free the bit, change or attach the bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger, complete the shutdown for its power type. Corded electric: release the switch or trigger, wait until the bit has stopped completely, then unplug it from the outlet by the plug, not the cord; before transport or storage, also let the motor cool. Battery: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where the model has one. Gas: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire and secure it away from the plug, and let the engine and muffler cool before touching the bit, engine, muffler or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown instructions in both the bit or attachment manual and the power-head or drill manual. If the bit sticks or material wraps around it, stop and complete the full shutdown before touching or inspecting it. Use only the freeing or clearing method specified in the exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when the exact manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. Wear safety glasses with side shields or goggles meeting the manual’s specification, including ANSI Z87.1 where required; add a face shield where required. Wear hearing protection with gas engines and wherever the manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional footwear protection the manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep them, clothing, hair, hands and feet away from moving parts. Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm that every notified utility has responded with markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Preserve the marks and follow your state’s ticket-validity and tolerance-zone rules. Keep the auger out of the required clearance area; near marks, use careful hand digging or another locating method permitted by state rules and the utility. Follow any stricter prohibition in the auger’s manual. Marks do not show a safe drilling depth. Arrange to locate private irrigation lines, cables and other services that 811 may not cover. If a line’s location remains uncertain, do not dig there. Do not handle or move unidentified cables, pipes or utility lines. Before you start, remove rocks, sticks, wire and loose hoses, and identify irrigation lines, drip lines and sprinkler heads. Keep children, pets and other people out of the work area and at least the distance your exact manual specifies. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs. No single distance is safe for every auger. On a slope or uneven ground, slow down, keep firm footing and follow only your manual’s rule. Do not dig in frozen or rock-hard ground. Before refuelling, complete the full gas shutdown described above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Keep fuel away from smoking, flames, sparks and other ignition sources. Use an approved fuel container, avoid overfilling, secure the cap and follow the manual’s spill-cleanup and restart-location instructions; do not start with a fuel leak. Use the specified fuel and oil arrangement for that engine. Never start or run a gas auger indoors, in a garage or shed, or in an enclosed or poorly ventilated area, even with doors open. Operate outdoors where exhaust cannot accumulate or enter occupied spaces through doors, windows or air intakes. Exhaust contains deadly carbon monoxide. For a corded auger, inspect the cord and extension cord before use and do not use damaged cords or plugs. Use an outdoor extension cord meeting the exact manual’s gauge, length, plug and grounding requirements, and follow its GFCI instructions. Keep connections dry and the cord clear of the bit, heat, oil and sharp edges. Never carry the auger by its cord or wrap the cord around your body. Do not use it in rain or wet conditions prohibited by the manual. Use only manufacturer-approved batteries and chargers for the exact model. Complete the battery shutdown before removing or changing a battery, and keep the switch off and fingers off the trigger when installing one. Do not use damaged or modified batteries or chargers. Keep loose battery terminals away from metal objects, and follow the battery and charger manuals for moisture exposure, charging temperature, cooling and storage. Load and unload only as your manual describes, and store the auger dry and out of children’s reach. Take breaks and stop when you are tired.

