A teal Makita UC4051A corded chainsaw and an Oregon CS1500 electric chainsaw resting on logs beside a woodpile in a sunny yard.

Makita UC4051A vs Oregon CS1500: Premium or Mid-Range Corded Chainsaw

Garden Power Scout Amazon Black Friday Banner

Makita UC4051A vs Oregon CS1500 comes down to a documented brake system against a built-in sharpener: buy the Oregon CS1500 if you cut small wood near an outlet and want a longer cut, and buy the Makita UC4051A if its brake system matters more to you than the extra length. I ran both corded saws on fallen plum limbs and orchard prunings lying on a stand beside the machinery shed. Below I compare power, cord rules, bar and chain, weight, brake, tension, oiler, sharpening and warranty, then give a pick for each buyer.

Affiliate Disclosure: Garden Power Scout is a proud participant in the Amazon Services LLC Associates Program.

Makita UC4051A vs Oregon CS1500: The Short Answer

The Oregon CS1500 is my pick for most buyers. It has the longer cutting length, a stated 15 amp motor, a built-in sharpener and a two-year warranty for registered personal use. The Makita UC4051A suits the buyer who wants a brake with a stated stop time plus a run-down brake, at a premium price tier and with a 14 inch cutting length. Both are rear-handle corded saws for wood that already lies on the ground. For a first saw, my top chainsaws for beginners list sorts saws with chain brakes for safer cuts.

Makita UC4051A and Oregon CS1500, as each maker’s manual states them
Spec Makita UC4051A Oregon CS1500
Saw type and power Corded electric, rear handle; amps and watts: Not published by the maker Corded electric, rear handle; 120 V, 15 A, 1800 W
Bar and cutting length 16 in sprocket-nose bar, 14 in cutting length (part 165202-6) 18 in bar, 17 in effective cutting length (part 180SDEA041)
Chain 91PX, 3/8 in pitch, 56 drive links; gauge: Not published by the maker PowerSharp, 3/8 in low-profile pitch, .050 in gauge; drive links: Not published by the maker
Chain speed 14.5 m/s (47.6 ft/s), the maximum 14.7 m/s (48.1 ft/s), no load
Weight 12.3 lb net, EPTA procedure 12.6 lb dry, assembled with bar and chain, no bar oil
Chain brake Hand-guard brake, chain stops within 0.15 s, plus a run-down brake Hand-guard brake, trips by hand or by kickback inertia; stop time: Not published by the maker
Chain tensioning Adjusting dial and sprocket cover lever, no tool named Tool-free ring turned by hand, release knob loosened first
Oiler Automatic, adjustable feed screw, oil level sight; tank size: Not published by the maker Automatic, 4.7 oz (140 ml) tank, inspection window
Sharpening Ordinary chain, 4.0 mm round file Built-in PowerSharp lever, PowerSharp chain and stone only
Extension cord Keyed to rating plate amps; 12 to 16 A row: 14 AWG to 25 ft, 12 AWG to 50 ft 14 AWG to 50 ft, 12 AWG from 51 to 100 ft, 100 ft the maximum
In the box Saw, 16 in bar and chain, bar cover; no bar oil or cord Saw, bar and chain, bar cover; no bar oil or cord
Warranty Separate Makita warranty sheet; term: Not published by the maker 2 years, registered personal use

Two rows decide it: the brake and the sharpening. The Makita documents its brake in detail, and the Oregon restores its edge with a lever in seconds.

What Each Corded Saw Is

Makita UC4051A 16 in Corded Electric Chain Saw is Makita’s 16 inch corded saw, sold under the same manual as the 14 inch UC3551A. The Makita UC4051A electric chainsaw is intended solely for cutting wood, according to Makita, which rules out forestry work and commercial use.

Oregon CS1500 18 in 15 Amp Self-Sharpening Corded Chainsaw is Oregon’s mid-range 18 inch corded saw. The Oregon CS1500 chainsaw is made for occasional light-duty use, according to Oregon, and it is not designed for large trees, wood thicker than its 17 inch cutting length or tree service. Neither box holds bar oil or an extension cord. My Oregon CS1500 saw review looks at that 18 inch saw on its own.

Neither maker presents these saws for tree work. Felling is the most dangerous chainsaw job. Never work alone, keep everyone at least two tree lengths away (Makita’s manual says 2 1/2 tree lengths in the direction of fall), and plan and clear two escape routes angled back from the direction of fall before any felling cut. A large, leaning, dead or hung-up tree, or a trunk or limb under tension after a storm, is a job for a certified arborist. Wood that already lies on the ground is the homeowner job for either saw.

Both manuals tell a first-time user to get instruction first and to practice on round timber on a trestle or sawhorse. Makita adds that you should not work alone and should stay within shouting distance of a second person.

Power, Cord and Extension Cord Rules

The Oregon CS1500 corded chainsaw is a 120 V, 15 A, 1800 W saw by Oregon’s manual. For the Makita, read the amps off the rating plate, because Makita keys its cord table to that figure.

The cord sets the real limit on both saws. Oregon’s table calls for 14 AWG up to 50 ft and 12 AWG from 51 to 100 ft, and 100 ft is the longest it lists. In Makita’s 12 to 16 A row the manual gives 14 AWG up to 25 ft and 12 AWG up to 50 ft and marks longer cords as not recommended, so match the row to your plate before you buy a cord. A battery saw removes the cord limit, and my ranking of battery chainsaws compares nine cordless saws by bar, brake and battery kit.

Use an outdoor-rated extension cord of the gauge your manual gives for its length, plug into GFCI-protected power, never use the saw in rain or wet conditions (GFCI protection does not make that safe), keep the cord away from the chain, and unplug it before any work on the chain. Makita adds that the electric motor is not waterproof.

I clipped the Makita’s cord hook onto the saw’s cord about 4 to 8 inches from the extension connector, as the manual shows, and ran the cord behind me to the shed outlet. With the Oregon I looped the extension cord through the hole in the rear handle and over the hook, so a tug lands on the handle and not on the plug. Keep bystanders, children and pets outside Oregon’s 20 ft (6 m) circle.

Bar, Chain and Chain Speed

The Makita carries a 16 inch sprocket-nose bar with a 14 inch cutting length, and the Oregon carries an 18 inch bar with a 17 inch effective cutting length. The cutting length is what counts: Oregon says never to cut wood thicker than 17 inches. My Oregon CS1500 against WEN 4017 comparison puts the same Oregon saw beside another corded saw.

The Makita runs a 91PX chain at 3/8 inch pitch with 56 drive links, and any Makita UC4051A replacement chain must match that type. Fit only the bar and chain that your saw’s manual approves, and keep a low-kickback chain on a homeowner saw. The Oregon takes PowerSharp chain at 3/8 inch low-profile pitch and .050 inch gauge, and the Oregon CS1500 replacement chain is part 571037.

Makita lists a maximum chain speed of 14.5 m/s (47.6 ft/s), and Oregon lists 14.7 m/s (48.1 ft/s) with no load. The labels differ and the gap is tiny, so I do not choose on that line.

Weight and Handling

Makita gives 12.3 lb net weight by the EPTA procedure, and Oregon gives 12.6 lb dry, assembled with bar and chain and no bar oil. The bases are worded differently, so I treat the two as one weight class. Both feel heavy at arm’s length: after an afternoon of bucking plum limbs on a stand, I felt the Makita’s 12.3 lb in my wrists and took a break between logs. For options across power sources, I compare nine battery, gas and corded saws in my ranking of the best chainsaws.

Hold the saw with both hands, right hand on the rear handle and left hand on the front handle, thumbs and fingers wrapped around the handles, with your body to the left of the chain line and firm footing. Never cut at or above shoulder height, and never cut from a ladder or a roof. Both saws have a spike bumper at the front: rest it on the wood and use it as a pivot, and switch the saw off between cuts, as Makita’s manual says.

On a plum log lying on a stand, I set the Makita’s spike bumper against the bark first and used it as the pivot before the chain went in. A study of groundskeepers found that chainsaws gave the highest hand-arm vibration of the tools it measured (1), so take breaks, and stop and see a doctor if your hands tingle or go numb and it persists.

Chain Brake and Pre-Use Checks

Both saws have a hand-guard chain brake. According to Makita, it stops the chain within 0.15 seconds and cuts the power to the motor, and a separate run-down brake stops the chain when you release the trigger. Oregon’s brake trips when the hand-guard moves forward or when kickback inertia acts on it, and it stops the motor and the chain.

The Makita UC4051A manual has you start the saw (lock-off button first, then the trigger) and press the front hand guard forward with the back of your hand: the chain must stop at once, and if it does not, Makita says not to use the saw under any circumstances. A run-down check follows: release the trigger completely and the chain must stop within a second. I pressed the guard forward with the back of my hand and watched the chain stop before the first cut of the day.

This saw will not run with its brake engaged, so pull the hand-guard back toward the front handle first. The Oregon CS1500 manual has you start the saw briefly on a firm, flat surface and roll your left wrist to push the hand-guard forward: the motor and chain must stop immediately. Rolling the wrist felt natural, and the chain stopped with the motor each time.

Before each use, inspect the saw as its manual describes: test the chain brake by the manual’s method, and check the throttle trigger lockout, the stop switch, the chain catcher, the guards and the chain’s sharpness, tension and condition; on a gas saw the chain must not move at idle. If any check fails, do not use the saw until it is repaired, and never disable a safety device.

If the upper part of the bar tip touches wood or another object, the bar can kick back up and toward you (rotational kickback). Wood pinching the chain on the top of the bar pushes the saw straight back at you (pushback), and wood pinching the bottom pulls it forward, away from you (pull-in). A low-kickback chain, a chain brake and a correct grip reduce these risks; none removes them. Laboratory tests on petrol saws found that proper chain tension, anti-kickback chain links, sliding-end guide bars and a quick chain brake all influence kickback (2). Both manuals say not to rely on the built-in safety devices alone.

Safety Gear Every Time

Wear impact-rated safety glasses with side protection marked Z87+ (a mesh face screen adds to them but never replaces them), hearing protection, chainsaw chaps or chainsaw trousers used within their maker’s stated limits (some are not designed to stop a battery or corded saw’s chain, and no clothing guarantees protection), work gloves and sturdy boots with ankle support, plus a hard hat when you fell a tree or anything can fall from above.

Makita’s manual asks for firm leather safety gloves and boots with non-slip soles, steel toes and cut-resistant lining. A corded saw has no exhaust, but the chain in wood is loud, so wear hearing protection every time. In a field test, helmet-mounted earmuffs held chainsaw noise at the ear to about 79 dB(A), with the cushions the weak point (3). Injury data shows why gear matters: only 3% of injured domestic users in an Irish survey wore any protective gear (4), and most of the injuries were to the legs.

Chain Tension, Oiler and Sharpening

Every chain job on either saw starts with the same order.

  • Stopping: release the trigger, engage the chain brake, switch the motor off and wait until the chain has stopped.
  • Maintenance (touching the chain, adjusting tension, changing the bar or chain): stop as above (release the trigger, engage the chain brake, switch the motor off, wait until the chain has stopped), pull the plug from the outlet by the plug, not the cord, and put on gloves before touching the chain. Release the chain brake only when the exact manual’s procedure requires it, and never force a locked chain or cover.
  • Carrying or moving the saw: stop as above, unplug it, engage the chain brake, point the bar behind you and fit the bar cover.

Neither saw needs a wrench for tension, and both jobs follow the maintenance order above. The Makita has you loosen the sprocket cover lever lightly, lift the bar tip slightly and turn the adjusting dial until the lower side of the chain sits snug against the bar rails. The Oregon has you turn the tensioning ring clockwise by hand with the release knob slightly loosened and the bar nose held up; the chain is right when it snaps back after a 3 mm pull, and Oregon says to check tension only with the chain cool and the saw unplugged. After the first few cuts with a new chain I rechecked tension on both saws, because both manuals ask for frequent checks.

Both saws oil the chain automatically, and neither box includes bar oil. Makita wants biodegradable saw chain oil with an adhesion agent and says never to use mineral oil, while Oregon says to use its own brand. Oregon says never to run the saw unless oil is visible in the window of its 4.7 oz (140 ml) tank, and before the first cut, or after long storage, it has you prime the oiler with the bar and chain removed as its manual describes, so follow that procedure exactly. On the Makita the oil can take up to two minutes to reach the chain on the first run.

Makita has you test the oiler by holding the running chain about 6 inches above a trunk or the ground and looking for a light oil trace, and not to use the saw if none appears. I did that over a hard pad beside the shed, away from the tree rows. After one night on the shed bench the Oregon left a dark patch of oil on the floor, which Oregon calls normal in storage, so it now sits on an absorbent pad with the bar cover on.

Sharpening is where the two part ways. Makita expects a 4.0 mm round file and names the signs of a dull chain: mealy sawdust, heavy cutting pressure, visible damage or a saw that pulls to one side. I noticed the pull to one side first, and a fresh edge fixed it.

With the saw at full speed, Oregon has you lift the PowerSharp lever lightly for 3 to 5 seconds, and sparks show the stone working. On a dry plum log the chips had turned to fine dust, and a few seconds on the lever brought them back. The built-in sharpener needs PowerSharp chain and the genuine stone, replaced with every new chain. The price of that convenience is lock-in: ordinary chain means removing the sharpener, which makes the Oregon CS1500 self sharpening corded electric chainsaw a closed system. Never use the PowerSharp lever near gasoline or acetylene.

Warranty and Service

Makita’s manual sends you to a separate warranty sheet and accepts claims only when the manual’s maintenance has been done regularly. It also says the chain brake and run-down brake wear and must be inspected regularly by Makita authorized or factory service centers. Oregon gives two years for a registered unit in personal use, with repair or replacement at its option, and the buyer pays shipping. Hired, rented or commercial use is not covered.

Choose the Makita UC4051A If

As a Makita corded electric chainsaw, the UC4051A earns its premium price tier with its safety system and upkeep design. Pick it when these describe you:

  • You want the brake documented in detail: a stated 0.15 second stop plus a run-down brake.
  • You cut often and will do the upkeep: a weekly grease on the bar-nose sprocket bearing with frequent use, brushes replaced at the limit mark and a regular brake inspection.
  • Your wood fits a 14 inch cutting length: limbs and short logs on a stand within a short cord run.
  • Skip it if you want the longest cut or a built-in sharpener.
Makita UC4051A corded electric chain saw in teal and black with a 16 inch bar
Makita UC4051A 16 in Corded Electric Chain Saw

SHOP ON AMAZON

Choose the Oregon CS1500 If

The Oregon CS1500 electric chainsaw suits the homeowner whose cutting happens within a short cord run of the house. It is a simple saw to live with once you pull the front hand-guard back, since it will not run with the brake engaged. Pick it when these describe you:

  • You want the longer cut: a 17 inch effective cutting length on an 18 inch bar.
  • You want to skip the file: a 3 to 5 second lift of the PowerSharp lever restores the edge, with PowerSharp chain and stone.
  • You need a long cord run: Oregon lists cords up to 100 ft, with 12 AWG for 51 to 100 ft.
  • Skip it for rain or wet ground, work beyond the cord, wood thicker than 17 inches or commercial use.
Oregon CS1500 corded electric chainsaw with 18 inch bar, gray and red housing and black rear handle
Oregon CS1500 18 in 15 Amp Self-Sharpening Corded Chainsaw

SHOP ON AMAZON

My Pick for Small Wood Near an Outlet

For small, dry wood that already lies on the ground within a cord run of an outlet, I pick the Oregon CS1500. The longer cutting length, the sharpener and the two-year registered warranty cover what most homeowners ask of a corded saw. The Makita UC4051A is for the buyer who puts the brake first and will do the upkeep: the weekly bar-nose grease, the brushes and the brake inspections. Both stop at the cord, both stay out of wet weather and both leave standing trees to trained crews. In the Makita UC4051A vs Oregon CS1500 choice, the Oregon wins on convenience and the Makita on documented brake protection. My best corded electric chainsaw list puts five plug-in saws in order by use.

Garden Power Scout Amazon Black Friday Banner

Frequently Asked Questions

How do you tighten the chain on a Makita UC4051A?

To tighten the chain on a Makita UC4051A, stop the saw and wait until the chain stops, unplug it by the plug, put on gloves, then loosen the sprocket cover lever lightly, lift the bar tip and turn the adjusting dial until the lower side of the chain sits snug on the bar rails. Retighten the cover without over-tightening.

How many amps does the Makita UC4051A use?

The Makita UC4051A uses the amps printed on its rating plate, and Makita’s manual matches the extension cord to that figure. In the manual’s 12 to 16 A row, the cord is 14 AWG up to 25 ft or 12 AWG up to 50 ft, and longer cords are not recommended for the saw.

What chain fits the Makita UC4051A?

The Makita UC4051A takes a 91PX chain with 3/8 inch pitch and 56 drive links on its 16 inch sprocket-nose bar, part 165202-6. Fit only the bar and chain the manual approves, and stop the saw, wait for the chain to stop, unplug it by the plug and put on gloves before you change either.

Why won’t an Oregon CS1500 chainsaw start?

An Oregon CS1500 chainsaw that won’t start has one of the causes Oregon lists: an engaged brake, an unpressed trigger lock-out, a tripped GFCI outlet, a damaged cord or debris around the side cover. Pull the hand-guard back, press the lock-out before the trigger, and stop the saw and unplug it by the plug before you look near the chain.

What replacement chain does the Oregon CS1500 use?

The Oregon CS1500 uses PowerSharp chain, part 571037, at 3/8 inch low-profile pitch and .050 inch gauge, with its bar part 180SDEA041. Oregon says to fit only the bars and chains it specifies, and the sharpening stone is replaced with every new chain, so stop the saw, unplug it by the plug and put on gloves before you change either.

References

  1. Chen N, Yang S, Oh J. Evaluation of hand-arm vibration (HAV) exposure among groundskeepers in the southeastern United States. Annals of Work Exposures and Health. 2025;69(1):81-95.
  2. Dąbrowski A. Reducing kickback of portable combustion chain saws and related injury risks: laboratory tests and deductions. Int J Occup Saf Ergon. 2012;18(3):399-417.
  3. Kirk P. Earmuff effectiveness against chainsaw noise over a 12-month period. Appl Ergon. 1993;24(4):279-283.
  4. Doyle YG, Conroy RM. Prevention of timber felling and chainsaw-related accidents in the Republic of Ireland. Accid Anal Prev. 1989;21(6):529-534.

Safety Note: Read your saw’s manual first and get hands-on training before your first cut. A chainsaw can react faster than you can: if the upper part of the bar tip touches wood or another object, the bar can kick back up and toward you; wood pinching the top of the chain can push the saw straight back at you, and wood pinching the bottom can pull it forward. Keep the bar tip out of contact and watch for wood closing on the bar. A low-kickback chain and a chain brake reduce these risks but never remove them. Before each use, inspect the saw as your manual describes: test the chain brake, and check the throttle lockout, the stop switch, the chain catcher, the guards and the chain. On a gas saw the chain must not move at idle. If any check fails or a part is missing or damaged, do not use the saw until it is repaired, and never disable a safety device. Wear impact-rated safety glasses with side protection marked Z87+ (a mesh face screen adds to them but does not replace them), hearing protection, chainsaw chaps or chainsaw trousers, work gloves and sturdy boots with ankle support, and a hard hat when you fell a tree or when anything can fall from above. Use leg protection within its maker’s stated limits: some chaps are not designed to stop the chain of a battery or corded saw, and no clothing guarantees protection. Hold the saw with both hands, right hand on the rear handle and left hand on the front handle, thumbs and fingers wrapped around the handles, and keep your body to the left of the chain line with firm footing. Never cut one-handed with a rear-handle saw, never cut at or above shoulder height, and never cut from a ladder or a roof. Top-handle saws are made for trained tree workers: follow that saw’s manual. Keep children, bystanders and pets well away while you cut. Never work alone. Start a gas saw with the chain brake engaged, on the ground or held firmly as the manual shows, never by drop-starting it, and at least 10 feet from where you fuelled it. Refuel outdoors with the engine off and cool, with no smoking, flames or sparks nearby, wipe up spills, and use only the fuel mix and ethanol content your manual allows. Exhaust contains carbon monoxide, which can kill: never run a gas saw indoors or in a garage, shed or other enclosed space. Before you touch the chain, clear a jam, adjust the tension or sharpen: release the trigger, engage the chain brake, stop the engine or motor and wait until the chain has stopped. Then, on a gas saw, let the engine and muffler cool and pull the spark plug cap off; on a battery saw, take the battery out; on a corded saw, unplug it by the plug. Put on gloves before you touch the chain, and release the chain brake only when your manual’s procedure calls for it. To carry the saw, stop it, take out the battery or unplug it, keep the chain brake engaged and the bar pointing behind you, and fit the bar cover for transport. Use a corded saw only with an outdoor-rated extension cord of the gauge your manual gives, plugged into GFCI-protected power. Never use it in rain or wet conditions: GFCI protection does not make that safe. Keep the cord away from the chain. Use only the chains and bars your manual approves. Felling trees is the most dangerous chainsaw job. Before any felling cut, keep everyone at least two tree lengths away, and plan and clear two escape routes angled back from the direction of fall; when the tree starts to fall, follow your manual’s retreat steps (release the trigger, stop the saw and set it down as it describes) and move away along that route; never delay escape to cool, unplug or cover the saw. A large, leaning, dead or hung-up tree, a trunk or limb under tension after a storm, and any tree near a house or a road are jobs for a certified arborist. Power lines are a separate danger: treat every downed line, and anything touching it, as live, stay well away and call the utility; before any work near a power line, contact the utility and leave that work to its qualified line-clearance crews. Stop when you are tired, and take breaks if your hands tingle or go numb.

Scroll to Top