Two men rolling a large hardwood round onto a towable gas log splitter at a logging site.

30 Ton vs 35 Ton Log Splitter: What the Extra 5 Rated Tons Really Change

The gap in a 30 ton vs 35 ton log splitter comparison is 5 rated tons, about 17 percent, and both numbers are the maker’s rating, never a measured force. The log length limit, the weight, the hydraulic oil capacity and the cycle time printed in the exact manual tell you more about a machine than its label does.

The rounds that come out of old apricot and plum trees on my orchard are modest, so I read the printed limits before I read the rating. Below I compare the two classes on those limits, then cover wood, weight and the safety rules that stay the same at either rating.

The Short Answer on a 30 Ton vs 35 Ton Log Splitter

Buy the rating your longest and thickest round needs, and treat the extra 5 tons as reserve. According to Champion, its 93520, rated 35 tons, takes logs up to 24 inches. Boss prints 25 inches in a manual that covers its 27, 32 and 37 ton versions. The rating alone does not state the log length, so read the exact manual.

What the Extra 5 Tons Give You

A 35 ton log splitter carries a bigger label, and I check what that label brings in the manual. No maker prints a tonnage guide by wood species, so I never read it as a promise that a 35 will split what a 30 will not. The extension tables later in this guide show how much the wood itself changes the job.

What the Extra 5 Tons Cost

In Yardmax’s gas table the bigger label brings more weight, more hydraulic oil and a slower printed cycle, and the cost section below gives the numbers. On my gravel yard, the first question I ask about a heavy machine is how I will roll it to the pile. I weigh the rolling question for each design in my towable and portable log splitters comparison.

Hands and Controls

Never put your hands or feet between the log and the wedge, the ram or any part of the splitter while it moves, and keep your fingers out of cracks that open in the log: they can close suddenly. Load the log by holding its sides, never its ends, and run the control only with your hand. Never tie down, block or bypass a two-hand control. Keep your hands clear during both the splitting stroke and the return stroke. Follow your manual’s unloading sequence; WEN 56207 requires the entire cycle to finish and the ram to retract fully before removing split wood. Never straddle or step over an operating splitter or reach or bend over it to retrieve a log.

What a 30 Ton and a 35 Ton Rating Really Mean

The rating is a number the maker prints on the label or in the model name. Makers also print that the number varies. According to Yardmax, “splitting force and cycle times may vary depending on mechanical and environmental conditions,” and BILT HARD says its published cycle time is for ideal conditions. I write “rated 35 tons” and never “35 tons of force.”

How a Rating Turns Into Force

Force equals pressure times piston area. That gives a way to check a label against the numbers printed beside it, and the label can land above or below the arithmetic. Powerhorse prints a 22 ton rating for its 117510 with a 4 inch bore and 3000 PSI. Here is the sum:

  1. A 4 inch bore has a piston area of about 12.6 square inches.
  2. 12.6 square inches at 3000 PSI is about 37,700 pounds.
  3. Divided by 2,000 pounds per ton, that is about 18.8 tons on paper, below the 22 ton label.

Champion goes the other way. Its 90720 prints 7 ton with a 3 inch cylinder and 3000 psi maximum pressure, which works out to about 10.6 tons on paper. I do not read 35 over 30 as a measured 17 percent more push. It is a 17 percent higher label, and the exact manual shows what stands behind it. The same label question for smaller machines is in my 10 against 20 ton splitters comparison.

Log Length and Diameter Limits Side by Side

The limit that decides what you can split is the maximum log length and diameter in your manual. It is a ceiling and never a target. The table lists what four manuals print for the 30 to 38 ton class, and Champion prints its weight as a net figure and Yardmax prints its weights without a stated basis, so compare weights only inside one maker’s rows.

30 Ton vs 35 Ton Log Splitter Dimensions

Printed figures for gas hydraulic splitters in the 30 to 38 ton range
Model, maker’s figures Rated tons Max log length Cycle time as printed Weight as printed
Yardmax YU3066 30 Not printed in the spec table 10.9 seconds 572 lb, basis not stated
Yardmax YU3566 35 Not printed in the spec table 12.8 seconds 636 lb, basis not stated
Champion 93520 35 24 in 16 seconds, max 584.2 lb net
Boss WD37T (one manual for three ratings) 27, 32 and 37 25 in 8 and 7.5 seconds, forward stroke Check your manual

Log length is capacity and not the machine’s overall size. Champion’s 35 ton prints 24 inches, and Boss’s manual for 27, 32 and 37 ton versions prints 25 inches. Yardmax’s table prints no log length for its 30 or its 35 ton, so these figures show the printed ceilings in the class and do not show how a 30 compares with a 35. My ranking of the best firewood log splitters sorts seven picks by log size and power.

Champion’s newer 100624 and 201258 manuals also print a 100 pound maximum log weight, a limit worth looking for in any manual before you lift a round. A round over the printed length or diameter stays off the machine, and the last section before the checklist says where it goes.

What the Bigger Class Costs in Cycle Time, Weight and Oil

The extra rating shows up in the numbers beside it. Heavier frames, bigger oil reservoirs and a slower cycle are the pattern in the one maker table that lists both ratings. Further down the range, my 20 and 25 ton splitters comparison examines another five-ton increase.

30 Ton vs 35 Ton Log Splitter Weight

Yardmax prints 572 pounds for the YU3066 and 636 pounds for the YU3566, a difference of 64 pounds, with no basis stated. Champion prints 584.2 pounds net for its 35 ton 93520, and I do not set that against the Yardmax figures. Weight decides how you move the machine, and I want to know that before the machine is sitting on my work pad by the shed.

Cycle Time and Oil Capacity

Yardmax’s table lists 25, 28, 30 and 35 ton models. Cycle times are 9.7, 13.2, 10.9 and 12.8 seconds, and hydraulic oil capacities are 4.2, 4.5, 4.5 and 6.0 gallons. The 28 ton is slower than the 30 ton, so cycle time does not climb in a clean line with the rating. The 35 ton prints 1.9 seconds longer than the 30 ton and holds 1.5 gallons more oil. My 25 and 30 ton splitters comparison puts the next step down side by side.

A short cycle is a design number and not a promise, and I never turn it into logs per hour. Compare cycle times only inside one maker’s table and only on one basis, extend only or extend plus retract.

What Extension Tables Say About Hard-to-Split Wood

No maker and no extension source gives tons per wood species or per log diameter. What exists are ease-of-splitting tables from universities, and they disagree with each other, so I name the university each time.

Oak, Elm and Hickory in Two Tables

Ease of splitting, as each university rates it
Wood University of Arkansas University of Kentucky
White oak Easy Good
Red oak Medium Fair
Hickory Medium Good
Black locust Difficult Good
Elm Difficult Poor

Arkansas lists the white oaks as easy and the red oaks as medium, and Kentucky rates white oak good and red oak fair. Both put elm at the hard end. Arkansas adds that splitting elm vertically is almost impossible without a hydraulic splitter. That points to a hydraulic machine of any rating, within the log limits in its manual, and not to a particular tonnage. I compare the two designs in my hydraulic and kinetic log splitters guide.

Grain, Knots and Moisture

Grain matters as much as species. The Wood Handbook describes interlocked-grain wood as exceedingly difficult to split radially (1). Seasoned firewood sits below 20 percent moisture, and green wood is normally above 60 percent (2). Maryland Extension says green, straight-grained wood generally splits more easily than seasoned wood, so the driest round in the stack is not always the easiest one.

Sun Joe’s manual says logs with knots or harder wood may be more difficult to split, and I review its LJ10M manual hydraulic model in my Sun Joe splitter review. When a round will not split in the time the manual allows, I stop and follow my manual’s reposition or reject procedure. A bigger rating gives me no reason to force it.

Safety Is the Same at 30 and 35 Tons

A heavier rating does not widen the safe zone. The rules below apply to both classes, and your exact manual overrides any general sentence here.

Shutdown, Hands and Operator

According to Champion, the wedge “can cut through skin and break bones.” Boss says its GD20T24 is “capable of amputating hands and feet and throwing debris.” A Vermont case series described disabling hand injuries from powered log splitters (3), and a Swedish study found that people hurt on wedge splitters often named more than one person at the machine as a cause (4). Injuries in that country’s registry ranged up to major in severity (5).

Full Shutdown

Shutdown before you free a stuck log, check or add fluid or oil, touch a hose, fitting or the wedge, clean, sharpen, adjust, move, tow, store or leave the splitter. Never use your hands to free a stuck log, and never check a hydraulic leak with your hand. Gas splitter: release the controls or return the hydraulic control lever to neutral as your manual directs, turn the engine off, wait until every moving part has stopped completely, including any flywheel, let the engine and muffler cool, and pull the spark plug wire off and secure it away from the plug. On a hydraulic splitter, relieve the hydraulic pressure as your manual describes before servicing it or touching any hose, fitting, cap or the wedge area. Never remove the hydraulic oil cap or vent plug while the machine is running or hot. Before moving, towing or storing a gas splitter, close the fuel valve where fitted as its manual directs. Use only the stuck-log procedure your manual gives, including its instructions for any powered clearing step, and refit every guard before restarting.

One Operator

One person operates the control. That person also loads the log unless the exact manual explicitly permits a loading helper. Never let anyone hold the log while you operate the splitter. If a loading helper is permitted, wait until the helper has left the operating area and reached the clearance required by the manual before moving the control.

Boss prints SINGLE OPERATOR for the WD37T, and Yardmax says the adult who loads and stabilizes the log must be the person who operates the control handle. I keep my hands off the log before the wedge touches it, and I leave them off until the ram has fully retracted.

Stuck Log

Never free a stuck log with your hands. Before intervening, complete the full shutdown in the shutdown box. Follow only your exact manual’s stuck-log procedure, including any instructions for a powered clearing step. Complete the full shutdown again before any further hands-on intervention.

Hydraulic Oil, Fuel and Starting

Escaping hydraulic fluid is the hazard people forget. Injection of fluid into the hand is treated as a surgical emergency, and a review of the literature found that early surgical treatment matters (6). Champion and Boss both tell the owner to pass cardboard or wood over a suspected leak and never a hand.

Hydraulic Fluid

Pressurised hydraulic fluid can inject through your skin from a hole too small to see. Never check for a leak with your hand: pass a piece of cardboard or wood over the spot and look for discolouration. If fluid hits your skin, see a doctor at once, even if the wound looks small. Before touching any hose, fitting or cap, complete the full shutdown for your splitter in the shutdown box, including hydraulic pressure relief exactly as your manual describes. Never open the hydraulic oil cap or vent plug while the machine is running or hot.

Gas Engine

Refuel outdoors with the engine off and cooled for several minutes, with no smoking, flames or sparks nearby, never overfill the tank, and wipe spills before you start. Never run a gas splitter indoors or in a garage or shed, even with the doors open: the exhaust contains carbon monoxide, which you cannot see or smell. Keep the clearances your manual gives (Champion: 3 feet on all sides and 5 feet from combustible material).

Start the engine using the exact procedure in its engine manual. Champion warns that rapid starter-cord retraction can pull your hand and arm toward the engine faster than you can let go. On cold mornings I follow the manual’s cold-start line and give the oil time to warm. Champion’s 90720 manual says the hydraulic oil needs to be above 10 F before the engine starts, because cold oil can damage the pump.

Site, Gear, Moving and Fatigue

The remaining rules cover where the machine stands, what you wear and what you split. I keep the list short because each line is a manual requirement and not a suggestion.

  • Site and weather: Set the splitter on firm, level, dry ground outdoors, never on a slope, ice, mud or slippery ground. Secure it against movement as the manual directs; Yardmax requires blocking the front and back of both wheels. Work in daylight or good artificial light as the manual permits, and keep split pieces cleared away from your feet.
  • Protective gear: Wear the eye protection your manual specifies (Champion calls for ANSI-approved safety glasses, and Boss calls for safety goggles or safety glasses with side shields), and a face shield where your manual asks for one; hearing protection with a gas engine or wherever your manual asks; sturdy boots, steel-toed where your manual asks; gloves exactly as your manual directs; and no loose clothing, jewelry, drawstrings or untied long hair.
  • Bystanders: Keep children, pets and other people out of the work area, at least the distance your manual prints, and stop the splitter if anyone comes closer. No distance makes a work area safe on its own: keep watching it. Boss prints 25 ft for the WD37T, and Champion’s 93520 manual prints no distance, so keep everyone well clear of the work area, as your manual describes.
  • What to split: Split one log at a time, with the grain and square-cut ends, within every size and weight limit your manual gives, including any minimum length. Check for nails, wire and other foreign objects. Do not use knotted, curved or uneven logs where your manual forbids them; Boss ES7T20 forbids uneven logs, including knotted or curved logs. Stop at the manual’s splitting time limit and follow its procedure for repositioning or rejecting the log; never force it.
  • Before every start: Check that the wedge, ram, beam, hoses and fittings are undamaged and tight, the fluid is at the level your manual gives, and every guard is in place. If the splitter leaks, groans, vibrates or moves the ram on its own, stop, complete the full shutdown and have it fixed before you use it again.
  • Towing: Tow the splitter only as its manual describes: a matching hitch and ball, safety chains attached exactly as the model’s manual specifies, the engine off and the fuel valve closed, no riders and no cargo on it, and never faster than the speed your manual prints.
  • Fatigue: Loading rounds is heavy, repetitive work. Follow your manual’s lifting and handling instructions and every printed log-weight limit. Take breaks and stop when you are tired or your attention slips.

Before you move, tow, store or leave the machine, complete the full shutdown for your splitter in the shutdown box above.

When a Log Is Beyond Both Machines

The mistake I see most is buying for the one big round of the year. A round wider or longer than the stated limit of a 30 or 35 ton machine goes to a larger rental machine with its own manual, or to a professional. It does not go onto a machine that cannot take it. Never hammer on the wedge or the log to make it fit, and never free a stuck log by hand. I explain how I choose the log splitter size I need by matching the machine to my logs, wood and use.

A Plain Checklist for Choosing the 30 Ton or the 35 Ton

Work through these steps before you compare two models, and the rating becomes the last decision.

  1. Write down the longest and thickest round you plan to split.
  2. Find the maximum log length and diameter in the exact manual of each model.
  3. Compare each machine’s weight, with its basis, against how you will move it.
  4. Compare cycle times only inside one maker’s table and on one basis.
  5. Choose the rating last, once the first four steps fit.
  • Choose the 30 ton if: the exact model’s printed length and diameter already cover your longest and thickest round, and you want the lighter frame and smaller oil reservoir its manual lists.
  • Choose the 35 ton if: the exact model’s printed limits cover your longest and thickest round, and you can handle the added weight and oil its manual lists.

Pick the Rating After the Limits Fit

Three things carry over. The rating is the maker’s label, the manual’s log limits decide what the machine may split, and the extra 5 tons brought more weight, more oil and a slower printed cycle in Yardmax’s table. My tip is to write down my longest and hardest round before I read a single rating, then check it against the manual’s ceiling. A 30 ton vs 35 ton log splitter choice is settled by the longest and hardest round you split once the printed limits fit. My list of the best log splitters ranks seven picks for home firewood work.

Frequently Asked Questions

Are oak logs hard to split?

Oak logs are moderately hard to split, and the difficulty depends on the species. The University of Arkansas rates white oaks easy and red oaks medium, while the University of Kentucky rates white oak good and red oak fair. Sun Joe says logs with knots or harder wood may be more difficult to split.

What is a 35 ton log splitter?

A 35 ton log splitter is a hydraulic splitter whose maker rates it at 35 tons, and makers print that real force varies with conditions. The Champion 93520 and the Yardmax YU3566 are gas hydraulic examples. Read their printed log limits and cycle times before you compare them.

What is a 30 ton gas log splitter?

A 30 ton gas log splitter is a hydraulic splitter driven by a gas engine and rated at 30 tons by its maker. The engine turns a hydraulic pump and uses engine oil and hydraulic oil at separate fill points. It must run outdoors only, because its exhaust contains carbon monoxide.

How do the dimensions of a 30 ton and a 35 ton log splitter compare?

The dimensions of a 30 ton and a 35 ton log splitter come from each model’s spec table, and the figures printed in the manuals read are log capacities. Champion prints 24 inches for its 35 ton 93520, and Boss prints 25 inches in a manual that covers its 27, 32 and 37 ton versions. Yardmax’s table prints no log length for either rating, so a direct comparison needs the exact manual of each model.

What size hydraulic cylinder does a 30 ton log splitter have?

The cylinder size on a 30 ton log splitter is printed in the maker’s spec table as a bore and a stroke, and it changes from model to model. Pressure times piston area gives the force on paper, and a maker’s rating can sit above or below that figure. Read the bore, stroke and pressure for your exact model, and treat the tonnage as the maker’s label.

References

  1. Ross RJ, ed. Wood Handbook: Wood as an Engineering Material. General Technical Report FPL-GTR-282. USDA Forest Service, Forest Products Laboratory; 2021.
  2. Taylor A. Moisture Content of “Seasoned” Firewood. W179. University of Tennessee Institute of Agriculture; 2014.
  3. Kristiansen TK, Seligson D. Log splitter injuries to the hand. J Occup Med. 1981;23(6):400-402.
  4. Lindqvist A, Nilsson O. Hand injury from powered wood splitters: machine safety, patterns of use and injury events. Int J Occup Saf Ergon. 2011;17(2):175-186.
  5. Lindqvist A, Berglund M, von Kieseritzky J, Nilsson O. Assessment of the severity of injuries to hands by powered wood splitters. J Plast Surg Hand Surg. 2010;44(4-5):237-244.
  6. Hogan CJ, Ruland RT. High-pressure injection injuries to the upper extremity: a review of the literature. J Orthop Trauma. 2006;20(7):503-511.

Safety Note: Only an adult who has read the manual and understands the controls should use a log splitter, never a child or anyone tired or impaired. The ram and wedge push with tons of force and can crush or cut off fingers, hands and feet: never put your hands or feet between the log and the wedge, the ram or any part of the splitter while it moves, keep your fingers out of cracks that open in the log, load each log by holding its sides, never its ends, and run the control only with your hand, never tying down, blocking or bypassing a two-hand control. Keep your hands clear during both the splitting stroke and the return stroke. Follow the manual’s unloading sequence; WEN 56207 requires the entire cycle to finish and the ram to retract fully before removing split wood. Never straddle or step over an operating splitter or reach or bend over it to retrieve a log. One person operates the control and also loads the log unless the exact manual explicitly permits a loading helper. Never let anyone hold the log while you operate the splitter. If a loading helper is permitted, wait until that helper has left the operating area and reached the manual’s required clearance before moving the control. Keep children, pets and other people out of the work area, at least the distance your manual prints for that exact model, and stop if anyone comes closer. No single distance is safe for every splitter. Set the splitter on firm, level, dry ground outdoors, never on a slope, ice, mud or slippery ground. Secure it against movement as the manual directs; Yardmax requires blocking the front and back of both wheels. Work in daylight or good artificial light as the manual permits, and keep split pieces cleared away from your feet. Never run an electric splitter in rain or damp conditions. Split one log at a time, with the grain and square-cut ends, within every size and weight limit your manual gives, including any minimum length. Check for nails, wire and other foreign objects. Reject knotted, curved or uneven logs where the manual forbids them; Boss ES7T20 forbids uneven logs, including knotted or curved logs. Stop at the manual’s splitting time limit and follow its procedure rather than forcing the log. Wear the eye protection your manual specifies: Champion calls for ANSI-approved safety glasses, and Boss calls for safety goggles or safety glasses with side shields. Also use a face shield where your manual asks for one, hearing protection with a gas engine or wherever your manual asks, sturdy boots (steel-toed where your manual asks), gloves exactly as your manual directs, and no loose clothing, jewelry, drawstrings or untied long hair. Pressurised hydraulic fluid can inject through your skin from a hole too small to see: never check for a leak with your hand, pass cardboard or wood over the spot instead, and see a doctor at once if fluid hits your skin, even if the wound looks small. Before freeing a stuck log, checking or adding fluid or oil, servicing, cleaning, sharpening, adjusting, moving, towing, storing or leaving the splitter, complete the shutdown for its power type. Electric: release the controls, switch the motor off, wait until every moving part has stopped completely, including the ram and any flywheel, then unplug it from the outlet by the plug. Gas: release the controls or return the hydraulic control lever to neutral as your manual directs, turn the engine off, wait until every moving part has stopped completely, including any flywheel, let the engine and muffler cool, then disconnect the spark plug wire and secure it away from the plug. Manual hydraulic: stop pumping and release the pressure exactly as your manual directs. On every hydraulic splitter, relieve hydraulic pressure as the manual describes before servicing or touching a hose, fitting, cap or the wedge area. Never remove the hydraulic oil cap or vent plug while the machine is running or hot, and never adjust pump or valve pressure settings. Before moving, towing or storing a gas splitter, close its fuel valve where fitted as the manual directs. Free a stuck log only by the manual’s procedure, including its instructions for any powered clearing step, never with your hands. Refit every guard before restarting. Use the grounded supply your manual requires and GFCI protection. If an extension cord is permitted, use a grounded three-wire outdoor-rated cord of the manual’s specified gauge and length. Keep connections away from water, keep the cord clear of moving parts and your feet, and never handle the plug with wet hands or disconnect it by pulling the cord. Refuel a gas splitter outdoors in a well-ventilated area with the engine off and cooled for several minutes, following any longer cooling period in its manual. Keep smoking, flames and sparks away, never overfill the tank, and wipe up spills before starting. Keep the manual’s clearances from surrounding objects and combustible materials. Never run it indoors or in a garage or shed, even with the doors open, because the exhaust contains carbon monoxide. Tow a towable splitter only as its manual describes, with towing chains attached exactly as the manual specifies, and never faster than the speed it prints. Store it dry and out of children’s reach, following the manual’s fuel-storage restrictions; Champion 100236 prohibits storing the unit indoors with fuel in its tank. Follow your manual’s lifting and handling instructions and every printed log-weight limit. Take breaks and stop when you are tired.

Scroll to Top