In the XtremepowerUS vs VEVOR post hole digger comparison, I recommend the corded XtremepowerUS 85060 for a handful of holes near an outlet and the gas VEVOR 43cc for holes the cord cannot reach. I used both on marked, cleared spots in the farm yard, and the distance to the outlet by the machinery shed mattered more than any spec. These are two different machines, so I compare bit, depth, weight, upkeep and what each manual prints on safety.
Affiliate Disclosure: Garden Power Scout is a proud participant in the Amazon Services LLC Associates Program. As an Amazon Associate, we earn from qualifying purchases, at no extra cost to you.
XtremepowerUS vs VEVOR Post Hole Digger: My Short Answer
I recommend the XtremepowerUS 85060 to most homeowners who set a few posts or plant a few shrubs within reach of an outdoor outlet, because it needs no fuel and no mixing. The VEVOR 43cc wins when no outlet is near the holes, since it carries its own engine and ships with an 8 inch bit. Neither is the right tool for frozen ground or ground full of roots and stones, and neither manual promises results there. My post hole digger picks rank seven corded, battery and gas models for home fence jobs.
| Spec | XtremepowerUS 85060 | VEVOR 43cc (D43-F) |
|---|---|---|
| Auger type | Corded electric earth auger, called a Hole Digger in its manual | Gas earth auger, called an Auger in its manual |
| Power | 110 V, 60 Hz, 10.9 amp; the manual cover and the listing say 1500W, the manual box list says 1200W | 43 cc 2-stroke engine, 1.25 kW maximum engine power per the manual; mixed fuel |
| Bit in the box | One bit: manual data table 4 in, manual safety text no more than 6 in bits, listing 6 in | One 8 in (200 mm) bit, 800 mm long per the manual (the listing says 30 in) |
| Maximum digging depth | Manual 560 mm (about 22 in); listing up to approximately 28 in | Not printed; the 800 mm is the length of the bit |
| Operators | Not printed; the manual shows a two-handle grip | Not printed; the listing photos show one person |
| Weight, basis not stated | 12.8 kg (about 28 lb) | 11.9 kg (about 26 lb) |
| Reverse | Not printed in the manual | Not printed in the manual |
| Bystander distance, manual | None printed | At least 5 m (about 16 ft) |
| In the box | Auger, one bit, 2 bolts, 2 nuts, hex spanner, manual | Auger, 8 in bit, two handles, screws and nuts, wrenches, 2 spark plugs, oil can (manual parts list) |
| Warranty term | Not printed in the manual | Not printed in the manual |
Two rows decide it: the power source and the bit in the box. Where a row gives two figures, the first is the manual’s and the second is the sales listing’s. Neither manual names the basis of its weight, so the two weights cannot be ranked.
What You Actually Get in Each Box
The XtremepowerUS 1500W electric post hole digger is a corded 110 volt tool sold as item 85060, and its box holds one bit. The VEVOR is a 43 cc gas tool with one 8 inch bit. The two do not line up row for row. My electric post hole digger picks cover other corded and battery models for home digging.
Full Shutdown Box
Shutdown before you clear or free the bit, change or attach the bit, free a stuck bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger. Never reach toward the bit while it turns, and never clear it or free it with the machine running. Corded electric auger: release the switch or trigger, wait until the bit has stopped completely, then unplug the auger from the outlet by the plug, not the cord. Before transport or storage, also let the motor cool. Gas auger: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire (a spark plug cap on some makes) and secure it away from the plug. Let the engine and muffler cool before you touch the bit or anything near the exhaust. Only then free a stuck bit or clear wrapped material, using only the method your manual specifies (gloves do not make grabbing sharp wire or cutting edges safe), and check the bit and guards for damage. Do not handle unidentified wire, cables or pipes. Do not use reverse or run the engine or motor to back the bit out unless your manual expressly authorizes it for this task, with both hands on the designated handles and everyone clear of the bit; complete the full shutdown again before any further hands-on work. Add every step your manual gives, in its order, and refit every guard and shield before you restart.
Two manual lines add to that box. The XtremepowerUS manual says to disconnect the plug before making adjustments, changing accessories or storing, and to remove any adjusting key or wrench before you switch it on. The VEVOR manual says to stop the engine and make sure every moving part has come to a standstill, and to switch off after hitting a foreign object or when the machine starts to vibrate abnormally. It never names the spark plug wire, so the box above supplies that step.
Before you fit a bit or handles, complete the full shutdown in the box above. The XtremepowerUS manual has you slide the bit onto the output shaft, push the bolt through and lock it with the nut. The VEVOR manual has you fit both handles with eight pairs of screws and nuts, then remove the clip and pin on the drill rod, align the holes and put the pin back.
The XtremepowerUS is the box where the sales page and the manual disagree. Its manual data table lists a 4 inch auger bit and its safety text says the machine operates with no more than 6 inch bits, while the listing sells it with a 6 inch bit. The depth splits the same way for the XtremepowerUS 85060 post hole digger, with a printed 560 millimeters in the manual and up to approximately 28 inches on the listing. Treat the manual’s figures as the maker’s and never go past its 6 inch limit.
The VEVOR 43cc post hole digger ships with one 8 inch bit and two handles you fit yourself. Its manual, model D43-F, lists the bit as 800 millimeters long, which the listing calls 30 inches, and prints no maximum depth, so that length is a bit length and never a depth. The same manual gives two different fuel ratios in two places; ask VEVOR which one applies.
XtremepowerUS Electric Post Hole Digger: What I Notice in Use
Before you move the machine, complete the full shutdown for your auger in the shutdown box above. With the plug out, I carried the XtremepowerUS from the machinery shed to a marked, cleared spot, then ran the cord from the outlet beside the shed, keeping it away from the bit. The manual says to position the auger upright at the drilling point, keep your feet stable and away from the bit, and firmly grip the two handles with both hands. With the red grips in gloved hands my elbows sat wide and the frame stood upright without a fight.
The manual then says to squeeze the switch trigger slowly and to press the handles lightly downward, and it warns against placing excessive body weight on the machine. I held back on the push. It says overloading can make the auger stop turning and to raise the auger often to clear cuttings from the hole, but it prints no method for freeing a stuck bit. If the bit stops, binds or the motor cuts out, I release the trigger and complete the full shutdown before I inspect anything, and I start again only when I know why it stopped and any damage is dealt with. Before you touch a stuck bit, complete the full shutdown for your auger in the shutdown box above.
The cord sets the reach. The manual asks for an outdoor extension cord that is heavy enough to carry the current and prints no gauge or length, so ask XtremepowerUS for the gauge and length before you buy a cord. From the shed outlet the cord covered the first marked spot, and a spot farther along would have meant moving the outlet, not the cord. My comparison of WORX against the XtremepowerUS auger shows what changes when two batteries replace the cord.

VEVOR Gas Post Hole Digger: What I Notice in Use
I started the VEVOR outdoors in the farm yard with ear protection on before I touched the starter cord. The manual says the machine is for outdoor use only and warns of hearing loss when it runs long without protection. Its start steps are to hold the drill vertically, set the rod against the ground, switch ON, pull the starter and take the holding handle and main handle in both hands.
On the throttle, the manual has you press and hold the safety switch and then pull the acceleration trigger gradually. The manual’s cue is that once the rod has penetrated 10 centimeters (4 inches) into the ground you grip the frame firmly and push harder. The two wide looped handles gave my hands room for that kind of push.
To stop, the manual says to release the trigger, turn the switch to OFF and let the machine stop completely before putting it on the ground. I never laid it down while the bit still turned. Before you lift or carry it, complete the full shutdown for your auger in the shutdown box above. The manual says to carry it by the handle, never by the drill, and I used both hands on the handle for the lift out of the shed.
The manual’s only line for a stuck bit is to release the accelerator and let the engine come back to idle. That is not a freeing method. Before I touch the bit I stop and complete the full shutdown in the shutdown box above, and since the manual gives no method past that, the next call goes to VEVOR support.

Corded or Gas: Power, Cord and Fuel
The XtremepowerUS runs on 110 volts at 10.9 amps and has no fuel to mix, store or spill. The VEVOR runs on a 43 cc 2-stroke engine, so every job starts with fuel, a spark plug and an exhaust. That one split makes the two different purchases, and it is the first thing I settle before bit or weight. My comparison of the XtremepowerUS and DC HOUSE augers sets the same corded unit beside a different gas engine.
For the corded XtremepowerUS, use the extension cord rule in your own manual: “Use an outdoor extension cord that meets your exact manual’s requirements for gauge, length, plug type and grounding. Keep the cord away from the bit, never carry the auger by the cord, and never use it in the rain. Follow your exact manual’s instructions for cord routing, disconnecting the plug, keeping connections dry and GFCI protection.” The XtremepowerUS manual says the tool must be grounded, forbids adapter plugs and says not to expose it to rain or wet conditions. It prints no gauge or length table.
For the gas VEVOR, the fuel rules matter more than anything else on the machine. Before refuelling, complete the full gas shutdown in the shutdown box above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Follow your exact manual’s precautions for ignition sources, filling the tank and dealing with spilled fuel. The VEVOR manual says fuel is highly flammable, never to smoke, never to add fuel to a running or hot engine, never to refuel inside a room, to use gasoline without ethanol or methanol, and to fill the tank to about 80 percent.
If fuel spills, do not start the machine; move it away from the spill. Mix fuel and oil only as the exact manual says, and ask VEVOR which of its two printed ratios applies.
Never start or run a gas auger indoors or in a garage or shed, even with the doors open. Start and run it outdoors: the exhaust contains deadly carbon monoxide, which has no color, taste or smell. A review of small-engine cases found that these engines can reach lethal carbon monoxide levels in poorly ventilated spaces (1). The VEVOR manual says gas emissions can cause injury and to use the tool outdoors only.
Winner: the XtremepowerUS for the buyer with an outlet in reach and no wish to handle fuel, and the VEVOR for the buyer whose holes sit past the cord.
Bit, Depth and Weight Compared Fairly
Either post hole digger auger can mislead you on its bit. The XtremepowerUS manual lists a 4 inch bit and says the machine operates with no more than 6 inch bits, while the VEVOR ships one 8 inch bit, 800 millimeters long per its manual. A bigger bit is not a deeper hole, and I never read one maker’s bit size against the other maker’s depth. My comparison of VEVOR 43cc and 52cc augers shows how bits, fuel and sound change within the brand.
On depth, the XtremepowerUS manual prints a drilling depth of 560 millimeters, about 22 inches, and its listing says up to approximately 28 inches. VEVOR prints no maximum depth for the D43-F, and the length of its bit is a bit length. Neither figure is a promise for hard clay or rock, and neither is a depth I recommend for your post or footing.
On weight, the XtremepowerUS manual prints 12.8 kilograms, about 28 pounds, and the VEVOR manual prints 11.9 kilograms, about 26 pounds. Neither manual says whether the bit is on or off, so the two numbers sit on unknown bases and cannot be compared. Both are hand-carried, with no wheels or carry aid. My comparison of the VEVOR 43cc with the DC HOUSE 52cc auger covers bits, weight and safety.
Winner: neither. The XtremepowerUS publishes a depth and the VEVOR publishes a larger bit, and the two figures answer different questions.
Safety Rules in Each Manual
Both manuals warn about the rotating bit, flying debris and loss of control, and they differ on the rest. What follows is the shared baseline, with each maker’s own lines where they differ. Your own manual always takes precedence.
Gear and Clear Ground
Wear safety glasses with side shields or goggles meeting your manual’s specification, including ANSI Z87.1 where required, and add a face shield where required. Wear hearing protection with gas engines and wherever your manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional protection your manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep hair, clothing, gloves, hands and feet away from moving parts.
The XtremepowerUS manual asks for eye protection, hearing protection above 85 dB(A), heavy duty non-slip gloves and sturdy boots with non-slip soles. The VEVOR manual says to always wear full protective equipment when using the machine, including a helmet, a protective mask, ear protection, gloves, non-slip footwear and protective clothing. Neither manual names ANSI Z87.1.
Before you start, walk the spot and remove rocks, sticks, wire, hose, stakes and anything else the bit could catch or throw. Identify irrigation lines, drip lines, cables and sprinkler heads before you start, and take loose garden hoses out of the work area. Do not handle or move unidentified cables, pipes or utility lines: keep the auger away from them and contact the utility if their location is uncertain.
Buried Lines
According to PHMSA, every digging project requires a call to the one-call center, even small projects like planting trees or shrubs, and the call is free. Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm responses from every notified utility, including markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging.
Follow state ticket-validity and tolerance-zone rules, preserve markings, and keep augers outside the required clearance area. Near marks, use careful hand digging or another locating method permitted by state rules and the utility; obey any stricter auger-manual prohibition. Arrange separate locating for private services that 811 does not cover (irrigation lines, cables). Do not dig where a service’s location remains uncertain, and do not bring in a larger machine as a workaround. Utility markings establish no safe augering depth above a buried service. Follow the requirements of your state’s one-call center, not an auger manual.
Buried utilities are a recognized safety risk and a cost in excavation work, which is why locating comes first (2). The XtremepowerUS manual says only that the machine is not designed for working in an area with underground electric, gas, water or telephone lines, and the VEVOR manual prints no underground-line warning at all. Neither tells you to call anyone, so the call to 811 is on you.
Bystanders, Binding and Stuck Bits
Keep children, pets and other people out of the work area and at least the distance specified in your exact manual. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs, and stop if anyone approaches. No distance makes a work area safe on its own: keep watching it. On a two-person unit, the second person is the operator’s helper only as your manual describes.
The VEVOR manual’s own figure is at least 5 meters, about 16 feet. The XtremepowerUS manual prints no distance and says to keep onlookers, especially children and animals, away from the area and to caution them to stand clear.
If the bit hits a root, a rock or a buried object, it can bind and the machine can twist or kick. Keep firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. Release the throttle or trigger immediately if the bit binds or control is threatened, then complete the full shutdown in the shutdown box and inspect for damage before restarting. Use reverse only where your manual authorizes it for your model.
A lab simulation of threaded-fastener tool profiles found that wrist muscles worked very hard against short torque pulses, even when the peaks were a small share of a person’s maximum strength (3). That is not an auger test, but it fits why a braced stance and two firm hands matter. Neither manual prints a reverse, so neither gives you a powered way to back a bit out.
If the bit sticks in the hole or material wraps around it, do not force it and do not reach for the bit. Stop and complete the full shutdown in the shutdown box before touching or inspecting it. Use only the freeing or clearing method specified in your exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when your manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. If your manual gives no procedure, obtain manufacturer or qualified service guidance.
People, Soil, Slopes and Fatigue
Use the number of people your exact manual specifies. A two-person unit needs a second person who knows the plan, holds the unit as the manual describes and stays clear of the bit, and both people stop when either calls a stop. A one-person unit is operated by one person; never add a helper to a hand-held unit unless the manual says so. Neither manual here prints an operator count.
Do not dig in frozen or rock-hard ground or in ground full of roots and stones: the bit can bind and the machine can twist or kick. On a slope or uneven ground, slow down, keep firm footing and follow only the slope or footing rule in your own manual. If your manual gives no such instruction, obtain guidance from the manufacturer before using the auger on a slope. The XtremepowerUS manual says normal operation is on level surfaces, and the VEVOR manual says not to use the machine on steep, slippery slopes or slippery surfaces, to avoid slopes in general and, where you absolutely cannot, to pay double attention.
Digging with an auger is heavy, jarring work that twists your arms and back. Take breaks, stop when you are tired or your attention slips, and use the gloves your manual recommends. On the gas VEVOR, a review of agricultural and forestry work found that workers exposed to both noise and hand-arm vibration lost more hearing than unexposed workers, so the ear protection stays on (4). Both manuals warn of white finger from long use, and a pooled analysis found that its risk rises with lifetime vibration exposure (5).
Before you lift, load, carry or move the auger, complete the full shutdown in the shutdown box. Load and unload only as your manual describes, never carry the auger by its cord, and refuel a gas unit on the ground, not in the truck bed. Follow the manual’s lifting and handling instructions.
Upkeep, Storage and Warranty
Neither machine asks much, and the VEVOR asks for more. The XtremepowerUS manual says to keep the body clean with a soft cloth dampened with mild soap and water, with no ammonia, chlorine or abrasives, and not to submerge it. The VEVOR manual has a maintenance table for oil level, air filter, spark plug and similar checks, and it says to check the rod and tool body for cleanliness, wear and damage after each use.
Before you clean either bit, complete the full shutdown for your auger in the shutdown box above. With the plug out of the XtremepowerUS or the spark plug wire secured on the VEVOR, I brush the soil off the flights and wipe the frame.
Before you store either machine or empty the VEVOR fuel tank, complete the full shutdown for your auger in the shutdown box above, and let the motor or engine cool. The VEVOR manual then says to store it dry and locked away from children, in its packaging, with the cutting device protection fitted if provided, and to empty the fuel tank completely for long storage. The XtremepowerUS manual says to store idle tools out of the reach of children.
Neither manual prints a warranty term, so I give none. The XtremepowerUS listing points to a separate page for warranty information, and the VEVOR manual points to its support and e-warranty page. Ask for the term in writing before you buy either one.
Choose the XtremepowerUS 85060 If
Pick the corded XtremepowerUS when the job is small and the outlet is close, since an electric post hole digger suits that job. Its trade is plain: no fuel, no starter cord and a manual that fits a handful of holes. My XtremepowerUS digger review goes through the 85060 in more detail.
- You have an outdoor outlet within cord reach of every marked spot.
- You want no fuel to mix, store or smell in the shed.
- A bit of 6 inches or less covers your holes, since the manual says the machine operates with no more than 6 inch bits.
Skip it if the holes are far from power or need a bigger bit. With nothing to fuel, the start by the machinery shed was simple, and that is the reason I recommend it for a few holes.
Choose the VEVOR 43cc If
Pick the gas VEVOR when the holes sit past the cord or need a wider bit, because a gas powered post hole digger needs no outlet. It trades convenience for reach, and for the upkeep of a 2-stroke engine. My comparison of the Earthquake and VEVOR augers sets this VEVOR 43cc beside the Earthquake E43.
- Your holes are beyond an outlet, in the farm yard or along a boundary.
- You want an 8 inch bit in the box, 800 millimeters long per the manual.
- You will mix fuel as the manual says and confirm the ratio with VEVOR first.
Skip it if you want a printed depth, an operator count, a reverse or a warranty term in the manual, because none of them is printed. The engine and the 8 inch bit made it feel like the tool built for distance, so put ear protection on before you pull the starter. My review of the VEVOR digger covers the 43cc model and its 8 in bit in more detail.
Which One I Would Pick for Your Fence Job
For a few posts near an outlet, I pick the XtremepowerUS and keep the shutdown box in my head every time. For holes the cord cannot reach, I pick the VEVOR and treat fuel, noise and carbon monoxide as part of the tool. Neither manual prints a reverse, an operator count or a warranty term, and the XtremepowerUS manual and listing disagree on bit, depth and watts, so I ask each maker before I buy. Call 811 before the first hole either way. That is where the XtremepowerUS vs VEVOR post hole digger choice lands for me: the corded 85060 for holes near an outlet, the gas 43cc for holes beyond it. My best auger for fence posts roundup compares gas, corded and battery models for that job.
Frequently Asked Questions
Does the XtremepowerUS post hole digger have reverse?
The XtremepowerUS post hole digger has no reverse printed in its item 85060 manual, so never use the motor to back the bit out of the soil. When the bit sticks, complete the full shutdown in the shutdown box above, because the manual gives no freeing method, and call XtremepowerUS or a qualified service shop for guidance.
What size bit comes with the VEVOR 43cc post hole digger?
The VEVOR 43cc post hole digger comes with one 8 inch bit, which its manual lists as 200 by 800 millimeters. The 800 millimeter length, which the listing calls 30 inches, is the length of the bit, not a digging depth, because VEVOR publishes no maximum depth for this kit and the box holds no extension rod.
Does the VEVOR gas post hole digger need mixed fuel?
The VEVOR gas post hole digger runs on mixed fuel, and its manual gives two different ratios in two places. Confirm the ratio with VEVOR support before you fill the first tank, use gasoline without ethanol or methanol, and mix fuel and oil outdoors only as the exact manual says.
How far should bystanders stand from the VEVOR 43cc post hole digger?
Bystanders should stand at least 5 meters, about 16 feet, from the VEVOR 43cc post hole digger, which is the distance its manual gives around the work area. No distance makes the area safe on its own, so stop the machine when anyone walks in and keep watching the space.
Is the VEVOR post hole digger a one-person machine?
The VEVOR post hole digger has no one-person or two-person rating printed in its D43-F manual, and its listing photos show one person firmly holding both handles. Use the number of people your own manual specifies, and never add a second helper to a hand-held unit unless the manual says so.
References
- Hyson BE, Friedman BM, Spear B, Bishop-Freeman SC. Lethal carbon monoxide generated from small internal combustion engines. J Anal Toxicol. 2024;48(8):625-629.
- Gallagher AG, Hart M, Cleary D, et al. Proficiency based progression simulation training significantly reduces utility strikes: a prospective, randomized and blinded study. PLoS One. 2020;15(5):e0231979.
- Armstrong T, Bir C, Foulke J, Martin B, Finsen L, Sjogaard G. Muscle responses to simulated torque reactions of hand-held power tools. Ergonomics. 1999;42(1):146-159.
- Thaper R, Sesek R, Garnett R, Acosta-Sojo Y, Purdy GT. The combined impact of hand-arm vibration and noise exposure on hearing sensitivity of agricultural/forestry workers: a systematic literature review. Int J Environ Res Public Health. 2023;20(5):4276.
- Scholz MF, Brammer AJ, Marburg S. Exposure-response relation for vibration-induced white finger: inferences from a published meta-analysis of population groups. Int Arch Occup Environ Health. 2023;96(5):757-770.
Safety Note: Only an adult who has read the manual and understands the controls should use an earth auger or post hole digger, never a child or anyone tired or impaired. Use the number of people your manual specifies, and keep everyone else out of the work area. The rotating bit can catch hair, clothing and gloves, and it can bind on a root, a rock or a buried object: the machine can then twist or kick in your hands. Stand with firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. If utility contact or a gas leak is suspected, stop work immediately. Do not touch, inspect, free or move the auger or exposed service, and do not attempt the normal hands-on shutdown or disconnect electrical connections in the suspected leak area. Leave the area, keep others away and contact the utility from a safe location; call 911 for a suspected gas leak or immediate danger. Otherwise, release the throttle or trigger immediately if the bit binds or control is threatened, then follow the shutdown procedure. On a two-person unit, both operators must understand the controls and agree on start and stop signals before starting; stop whenever either operator calls stop. Use reverse only where your manual expressly authorizes it. Never touch or clear the bit while it turns. Before you clear or free the bit, change or attach the bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger, complete the shutdown for its power type. Corded electric: release the switch or trigger, wait until the bit has stopped completely, then unplug it from the outlet by the plug, not the cord; before transport or storage, also let the motor cool. Battery: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where the model has one. Gas: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire and secure it away from the plug, and let the engine and muffler cool before touching the bit, engine, muffler or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown instructions in both the bit or attachment manual and the power-head or drill manual. If the bit sticks or material wraps around it, stop and complete the full shutdown before touching or inspecting it. Use only the freeing or clearing method specified in the exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when the exact manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. Wear safety glasses with side shields or goggles meeting the manual’s specification, including ANSI Z87.1 where required; add a face shield where required. Wear hearing protection with gas engines and wherever the manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional footwear protection the manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep them, clothing, hair, hands and feet away from moving parts. Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm that every notified utility has responded with markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Preserve the marks and follow your state’s ticket-validity and tolerance-zone rules. Keep the auger out of the required clearance area; near marks, use careful hand digging or another locating method permitted by state rules and the utility. Follow any stricter prohibition in the auger’s manual. Marks do not show a safe drilling depth. Arrange to locate private irrigation lines, cables and other services that 811 may not cover. If a line’s location remains uncertain, do not dig there. Do not handle or move unidentified cables, pipes or utility lines. Before you start, remove rocks, sticks, wire and loose hoses, and identify irrigation lines, drip lines and sprinkler heads. Keep children, pets and other people out of the work area and at least the distance your exact manual specifies. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs. No single distance is safe for every auger. On a slope or uneven ground, slow down, keep firm footing and follow only your manual’s rule. Do not dig in frozen or rock-hard ground. Before refuelling, complete the full gas shutdown described above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Keep fuel away from smoking, flames, sparks and other ignition sources. Use an approved fuel container, avoid overfilling, secure the cap and follow the manual’s spill-cleanup and restart-location instructions; do not start with a fuel leak. Use the specified fuel and oil arrangement for that engine. Never start or run a gas auger indoors, in a garage or shed, or in an enclosed or poorly ventilated area, even with doors open. Operate outdoors where exhaust cannot accumulate or enter occupied spaces through doors, windows or air intakes. Exhaust contains deadly carbon monoxide. For a corded auger, inspect the cord and extension cord before use and do not use damaged cords or plugs. Use an outdoor extension cord meeting the exact manual’s gauge, length, plug and grounding requirements, and follow its GFCI instructions. Keep connections dry and the cord clear of the bit, heat, oil and sharp edges. Never carry the auger by its cord or wrap the cord around your body. Do not use it in rain or wet conditions prohibited by the manual. Use only manufacturer-approved batteries and chargers for the exact model. Complete the battery shutdown before removing or changing a battery, and keep the switch off and fingers off the trigger when installing one. Do not use damaged or modified batteries or chargers. Keep loose battery terminals away from metal objects, and follow the battery and charger manuals for moisture exposure, charging temperature, cooling and storage. Load and unload only as your manual describes, and store the auger dry and out of children’s reach. Take breaks and stop when you are tired.


