In the VEVOR 43cc vs DC HOUSE 52cc choice, I pick the DC HOUSE 52cc for most buyers: its manual prints the fuller safety steps, and its product page lists two bits in the kit. The VEVOR wins when you want one 8 in bit and a longer bystander distance printed in its own manual. I run a 3.7-acre apricot and plum orchard, so planting holes are the digging job I judge a machine by. Both are budget gas earth augers with gaps in their manuals, so below I compare bits, engine, weight, controls, safety text and warranty.
Affiliate Disclosure: Garden Power Scout is a proud participant in the Amazon Services LLC Associates Program. As an Amazon Associate, we earn from qualifying purchases, at no extra cost to you.
VEVOR 43cc vs DC HOUSE 52cc: The Short Answer
For most buyers I recommend the DC HOUSE 52cc, and the printed safety steps are the reason. The DC HOUSE 52cc Gas Earth Auger with 6 in and 10 in Bits is a budget gas earth auger whose manual names a spark plug disconnection step, a warning that the auger may twist suddenly and a helper position, which the VEVOR 43cc Gas Post Hole Digger with 8 in Bit manual does not print. The VEVOR is also budget-priced and is my pick when you want an 8 in bit, because its manual lists one 8 in by 30 in bit and a 5 m bystander distance. Each figure below is the one that maker’s own manual prints, and where a manual and the product page disagree I say so. My list of earth augers I compared covers seven gas, corded and battery models.
| Feature | VEVOR 43cc | DC HOUSE 52cc |
|---|---|---|
| Auger type, maker’s words | Gas 2-stroke “Post Hole Digger”, hand-held | Gas 2-cycle earth auger, hand-held |
| Engine, manual’s figures | 43 cm3 engine, maximum engine power 1.25 kW | 52 cc engine, maximum output 1.3 kW |
| Bits in the kit | One 8 in (200 mm) bit, 30 in (800 mm) long | 6 in and 10 in bits per the product page; the manual says the bit assembly is bought separately |
| Maximum digging depth | Not published by the maker; 30 in is the bit length | Not printed in the manual text; its page image labels the single bit “31.5 in, 80 cm”, a bit length |
| Operators | Not published by the maker | Manual describes an operator and a helper holding a support handle |
| Weight, manual (basis not printed) | 11.9 kg (about 26 lb) | 10.4 kg (about 23 lb) |
| Handles and controls | Two looped handles, a safety switch and an acceleration trigger | Throttle handle with a trigger lockout lever, a lower support handle and a stop switch |
| Reverse | Not printed in the manual | Not printed in the manual |
| Bystander distance, manual | 5 m (about 16 ft) | 3 m (10 ft) |
| Spark plug disconnection in the manual | Not printed | Printed |
| Underground lines in the manual | No warning printed | Names electrical, gas, water, cable and telephone lines; no 811 or locate step |
| Warranty, manual | No term printed | Contradicts itself: an 18-month heading, then 12 months, plus a 30-day money-back line |
Two rows decide the pick: the bits row and the safety steps on binding and the spark plug. The weight row cannot decide it, because neither manual says what its weight includes.
Bits and What Comes in the Box
The bits are where the two kits differ most, because they decide which hole sizes you can start with. Fitting or changing a bit is hands-on work, so the shutdown box comes first.
Shutdown Before You Clear, Free, Change or Move the Bit
Shutdown before you clear or free the bit, change or attach the bit, free a stuck bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger. Never reach toward the bit while it turns, and never clear it or free it with the machine running. Gas auger: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire (a spark plug cap on some makes) and secure it away from the plug. Let the engine and muffler cool before you touch the bit or anything near the exhaust. Only then free a stuck bit or clear wrapped material, using only the method your manual specifies (gloves do not make grabbing sharp wire or cutting edges safe), and check the bit and guards for damage. Do not handle unidentified wire, cables or pipes. Do not use reverse or run the engine or motor to back the bit out unless your manual expressly authorizes it for this task, with both hands on the designated handles and everyone clear of the bit; complete the full shutdown again before any further hands-on work. Add every step your manual gives, in its order, and refit every guard and shield before you restart.
Before you do this, complete the full shutdown for your auger in the shutdown box above. The VEVOR kit holds one 8 in (200 mm) bit, 30 in (800 mm) long, which its manual lists as 200 by 800 mm. The bit goes on a drill rod held by a clip and a pin: the manual says to remove the clip and pin, install the rod, align the holes and put the pin back by clipping it. I stood the 8 in bit next to a post in the shed, and it looked wide beside it.
The DC HOUSE manual and the seller’s product page disagree about the box. The page lists a 6 in and a 10 in bit (the ED52A610 set), while the manual says the auger assembly is purchased separately as an accessory, so I attribute the two bits to the page. The DC HOUSE earth auger in that kit has no extension rod, and the manual’s page image labels the single bit “31.5 in, 80 cm”. That figure is a bit length, not a digging depth, and neither 31.5 in nor the VEVOR’s 30 in is a digging depth, because neither maker prints a maximum depth in its manual text. My DC HOUSE auger review goes through the kit and its two bits.
A reader who wants one bit and nothing else gets exactly that from the VEVOR earth auger. Whichever machine you pick, confirm the approved bit sizes for that exact model with the maker before you buy another bit.
Winner: DC HOUSE 52cc, because two bit sizes arrive in one kit according to its product page.
Engine, Starting and DC HOUSE 52cc Auger Fuel Mixture
Both machines are 2-stroke gas augers with a recoil starter, so the differences sit in the steps and in what each manual gets wrong. Everything in this section that touches fuel starts with the shutdown box above.
The VEVOR gas post hole digger manual prints a 43 cm3 engine with a maximum power of 1.25 kW and a 1.2 L tank. Its start steps are short: switch ON, pull the starter, grip both handles, then “gradually increase the speed by pressing and holding the safety switch and then pulling the acceleration trigger”. On the VEVOR post hole digger 43cc, my thumb found the safety switch without looking, which matters with gloves on. My VEVOR digger review covers this model on its own.
The DC HOUSE manual prints a 52 cc engine with a maximum output of 1.3 kW and a 1.3 L tank, and it calls the drive an automatic centrifugal clutch. The manual says to set the choke, switch the power switch on, press the primer 7 to 8 times and pull the starter until you feel resistance. The purge bulb is a small detail, but I liked that it gave me a step to finish before the first pull. The throttle trigger will not move until the lockout lever is engaged, as the manual describes, which keeps a knock on the trigger from opening the throttle.
Fuel mix is where both manuals fail the buyer. The VEVOR manual gives one ratio in its text and another in its technical table, and the DC HOUSE manual gives a ratio in its headline while its worked ounces match neither that nor the figure on the product page. For the DC HOUSE 52cc auger fuel mixture and for the VEVOR alike, get the maker’s confirmed ratio before the first tank, use no ratio from the product page, and mix only as the exact manual says. Because the product page lists a higher power figure than the manual, I use only the manual’s 1.3 kW. I also cover fuel and manual gaps in my comparison of VEVOR 43cc and 52cc augers.
Refuelling a Gas Auger
Before refuelling, complete the full gas shutdown in the shutdown box. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Follow your exact manual’s precautions for ignition sources, filling the tank and dealing with spilled fuel. Mix fuel and oil only as the exact manual says.
Carbon Monoxide
Never start or run a gas auger indoors or in a garage or shed, even with the doors open. Start and run it outdoors: the exhaust contains deadly carbon monoxide, which has no color, taste or smell.
A medical examiner’s review tied carbon monoxide cases to small gasoline engines running in poorly ventilated spaces (1). That review concerned other small engines and not these augers, and it is the reason my rule is outdoors only, never a shed with the door open. The VEVOR manual says never to use the tool indoors and does not print the words carbon monoxide, and the DC HOUSE manual names it. Outdoors only is the rule for both.
Winner: a tie, because 1.25 kW and 1.3 kW are each the maker’s own figure and sit close together, and neither manual’s fuel mix is clear.
Handles, Operators and Control in a Bind
An auger can bind on a root or a stone and twist in your hands, so the handles and the stop procedure matter more than the engine size. Every hands-on step in this section starts with the shutdown box above.
The VEVOR has two wide looped handles, and its manual says to hold the drill vertically with the rod against the ground. After the rod has gone about 10 cm into the ground, the manual says to “grasp the frame strongly and increase the effort downwards”. The manual does not say whether one person or two run this machine, so I write that it is not published. With both gloved hands on the loops, I could hold the VEVOR upright with my elbows close to my body.
The DC HOUSE has a throttle handle, a lower support handle and a stop switch, and its manual says to hold both handles with thumbs and fingers tightly encircling them. It describes a two-man operation, with an operator guiding the auger and a helper on the support handle, and says larger holes of six inches or more “may be easier if two people hold the handles on opposite sides”. The manual also says never to run the auger with the handles above chest height. At the start position on the DC HOUSE, I checked that the handles stayed below my chest before I gave it any throttle.
Binding and Torque Reaction
If the bit hits a root, a rock or a buried object, it can bind and the machine can twist or kick. Keep firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. Release the throttle or trigger immediately if the bit binds or control is threatened, then complete the full shutdown in the shutdown box and inspect for damage before restarting. Use reverse only where your manual authorizes it for your model.
The DC HOUSE manual warns that “the auger may twist suddenly and forcefully if it contacts large rocks, roots, or other hidden obstacles” and says to release the throttle trigger at once. The VEVOR manual prints no twist or kickback warning, only a general warning about sudden impact from hidden objects, so the box above is my rule on both. A laboratory study of simulated torque pulses on a handle found very high wrist muscle activity even when the pulses were short and the peaks low (2), and a scoping review of assembly workers linked repeated handle reaction loads to physiological changes (3). Those studies measured lab handles and factory tools, not augers, so they tell me why a firm grip matters, not how hard either machine twists.
Stuck Bit
If the bit sticks in the hole or material wraps around it, do not force it and do not reach for the bit. Stop and complete the full shutdown in the shutdown box before touching or inspecting it. Use only the freeing or clearing method specified in your exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when your manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. If your manual gives no procedure, obtain manufacturer or qualified service guidance.
VEVOR’s manual says that when the drill gets stuck you release the accelerator and let it return to idle. That eases the load and leaves the engine running, so the full shutdown in the box comes before I reach toward the bit. The DC HOUSE manual explicitly requires disconnecting the spark plug before removing obstructions, a step the VEVOR manual does not print, and on both machines the full shutdown in the shutdown box above comes first. If either bit meets a root or a buried stone, I release the trigger, shut down fully and inspect, and I do not restart until the cause is found and any damage is repaired.
One-Person and Two-Person Units
Use the number of people your exact manual specifies. A two-person unit needs a second person who knows the plan, holds the unit as the manual describes and stays clear of the bit, and both people stop when either calls a stop. A one-person unit is operated by one person; never add a helper to a hand-held unit unless the manual says so.
For the DC HOUSE, that means the helper’s position is the support handle only, as its manual says. The VEVOR manual prints no operator count, so I do not add a helper to that machine.
Winner: DC HOUSE 52cc, because its manual prints the twist warning, the helper position and the spark plug step that the VEVOR manual leaves out.
Weight and Moving It
Weight decides how willing you are to carry the machine to the hole, and here the two manuals leave a gap. Before you do this, complete the full shutdown for your auger in the shutdown box above.
The VEVOR manual prints 11.9 kg (about 26 lb) in its technical data, and the DC HOUSE manual prints a net weight of 10.4 kg (about 23 lb). Neither says whether the figure includes the bit, fuel or the handles, so the figures do not give a comparable carrying weight. I lifted the VEVOR off the shed shelf by its frame, since the manual says to carry the tool by the handle and never by the drill, and it felt like a two-hand lift.
Lifting and Transport
Before you lift, load, carry or move the auger, complete the full shutdown in the shutdown box. Load and unload only as your manual describes, never carry the auger by its cord, and refuel a gas unit on the ground, not in the truck bed. Follow the manual’s lifting and handling instructions.
The DC HOUSE manual says never to carry the auger between holes with the engine running, and I carry it to the shed by the handlebar frame once the full shutdown is done. For storage, VEVOR’s manual says to empty the fuel tank completely for long storage, keep it dry and fit the bit protection if one is provided. DC HOUSE’s manual says not to store a unit with fuel in its tank and not to store it where fuel fumes can reach a flame or spark.
Winner: a tie, because 11.9 kg and 10.4 kg come without a stated basis.
What Each Manual Says on Safety
The two manuals cover safety to different depths, and I read both from cover to cover before running either. Here is what each one prints, with the general rules for gas augers alongside.
Clothing and Protective Gear
Wear safety glasses with side shields or goggles meeting your manual’s specification, including ANSI Z87.1 where required, and add a face shield where required. Wear hearing protection with gas engines and wherever your manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional protection your manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep hair, clothing, gloves, hands and feet away from moving parts.
DC HOUSE names eye protection that meets ANSI Z87.1 or CE requirements, hearing protection whenever the unit is used, rubber work gloves, long pants and sleeves, and no shorts. VEVOR recommends resistant gloves, non-slip shoes and safety glasses, and says to wear full protective equipment including a helmet, mask and ear protection, with no standard named.
Clear the Area
Before you start, walk the spot and remove rocks, sticks, wire, hose, stakes and anything else the bit could catch or throw. Identify irrigation lines, drip lines, cables and sprinkler heads before you start, and take loose garden hoses out of the work area. Do not handle or move unidentified cables, pipes or utility lines: keep the auger away from them and contact the utility if their location is uncertain.
Buried Lines
Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm responses from every notified utility, including markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Follow state ticket-validity and tolerance-zone rules, preserve markings, and keep augers outside the required clearance area. Near marks, use careful hand digging or another locating method permitted by state rules and the utility; obey any stricter auger-manual prohibition. Arrange separate locating for private services that 811 does not cover (irrigation lines, cables). Do not dig where a service’s location remains uncertain, and do not switch to a larger machine as a workaround. Never assume a safe augering depth above a buried service.
According to PHMSA, the call is free, the waiting time differs by state, and operators mark their facilities with flags or paint. The DC HOUSE manual says to beware of underground hazards such as electrical lines, gas lines, water mains, and cable and telephone lines, though it names no locate step. The VEVOR manual prints no underground-line warning, so for that machine the 811 steps above are all you have. Where a line cannot be located and marked, or a utility response is missing, no auger goes into that ground.
Bystanders
Keep children, pets and other people out of the work area and at least the distance specified in your exact manual. Stop if anyone enters that area. No distance makes a work area safe on its own: keep watching it. On a two-person unit, the second person is the operator’s helper only as your manual describes.
The VEVOR manual asks for at least five meters (about 16 ft) around the work area, and the DC HOUSE manual asks for 3 m (10 ft). Those are two makers’ own figures for their own machines, and neither is a safe distance: I stop whenever anyone walks into either one.
Slopes and Footing
On a slope or uneven ground, slow down, keep firm footing and follow only the slope or footing rule in your own manual. If your manual gives no such instruction, obtain guidance from the manufacturer before using the auger on a slope.
The VEVOR manual says “Do not use the product on steep, slippery slopes” and separately says to avoid working on slopes and, if you must, to pay double attention. The DC HOUSE manual prints no slope rule, but it says not to stand on slippery, uneven or unstable surfaces, and that prohibition takes precedence over the general advice above to slow down on uneven ground: on such ground you do not run that auger.
Soil Condition
Do not dig in frozen or rock-hard ground or in ground full of roots and stones: the bit can bind and the machine can twist or kick.
The DC HOUSE manual adds that you should not operate the unit in excessively rocky ground. The VEVOR manual warns of hearing loss from long use without hearing protection and describes “white finger” from prolonged vibration, and it says to see a doctor at once for numbness, tingling, pain or a color change. A review of 18 studies found that workers exposed to both hand-arm vibration and noise had more hearing loss than unexposed workers (4), and occupational vibration exposure is common enough to reach rheumatology clinics (5). Those are studies of workers and not a reading for either auger, so I treat them as a reason to stop for a rest and to put on ear protection from the first start.
Fatigue and Vibration
Digging with an auger is heavy, jarring work that twists your arms and back. Take breaks, and stop when you are tired or your attention slips, and use the gloves your manual recommends.
Winner: DC HOUSE 52cc, because its manual prints more of the steps, while the VEVOR manual prints the longer bystander distance.
Warranty, Support and Manual Quality
A budget auger lives or dies on its paperwork when something fails, and neither manual is clean. Reading both side by side showed me where each one needs a call to the maker.
The VEVOR manual points to a support and e-warranty page on the cover and prints no warranty term, and it says the machine is for private domestic use only and that people under 18 must not use it. The DC HOUSE manual contradicts itself: an “18-Month warranty” heading is followed by a line that gives 12 months for a replacement or refund, and it also mentions a 30-day money-back guarantee. Its manual also says to add fuel stabilizer to the gasoline or the warranty is void. My DC HOUSE and VEVOR augers comparison puts the two 52cc machines side by side.
The DC HOUSE manual also conflicts with itself on mix ratio and gear reduction, and its tank size differs from the product page, so ask the seller to confirm every figure that matters in writing. For either machine, ask which warranty term applies to your order before you buy.
Winner: a tie, because the VEVOR prints no term and the DC HOUSE prints two.
Choose the VEVOR 43cc If
The VEVOR suits a buyer who wants a single 8 in bit, a printed 5 m bystander distance and a short, plain set of start steps. These are the situations that point to it:
- You want an 8 in bit in the box: the manual lists one 8 in by 30 in bit.
- You want the longer printed bystander distance: 5 m against the DC HOUSE manual’s 3 m.
- You want a manual that prints sound and vibration tables: the VEVOR manual prints them, with no distance named.
For a VEVOR vs DC HOUSE auger decision on safety text, skip it: the VEVOR manual prints no twist warning, no spark plug step and no underground-line warning.

Choose the DC HOUSE 52cc If
The DC HOUSE suits a buyer who wants two bit sizes, a manual with more printed safety steps and a helper position for larger holes. These are the situations that point to it:
- You want two bits: the product page lists a 6 in and a 10 in bit.
- You want the twist warning and the spark plug step printed: the manual carries both.
- You may work with a helper: the manual describes a support handle and a helper position.
Skip it if you want one 8 in bit in the kit or a manual that gives one warranty term and one fuel ratio.

Which Gas Auger Fits Your Planting Holes
Both machines are budget gas augers with the same kind of engine and the same need for care, so your holes and your habits decide the pick. Take the VEVOR if one 8 in bit is what you need and you can live without a printed twist warning, spark plug step and underground-line warning in the manual. Take the DC HOUSE if you want two bit sizes, a manual that prints those steps and a helper position for larger holes.
Whichever you choose, ask the maker to confirm the fuel ratio and the approved bit sizes in writing before you buy a bit or mix the first tank. The shutdown box earns its place before every bit change, every fuel top-up and every move to the shed, and for the VEVOR 43cc vs DC HOUSE 52cc decision, the DC HOUSE 52cc is the one I recommend to most buyers. My guide to gas earth augers puts five gas models side by side.
Frequently Asked Questions
What is the difference between the VEVOR 43cc and the DC HOUSE 52cc earth auger?
The difference between the VEVOR 43cc and the DC HOUSE 52cc earth auger is mostly the kit and the manual: the VEVOR ships one 8 in bit, while the DC HOUSE page lists 6 in and 10 in bits. The DC HOUSE manual also prints more safety steps, such as a spark plug disconnection and a helper position.
Which comes with more bits, the VEVOR 43cc or the DC HOUSE 52cc?
The DC HOUSE 52cc comes with more bits, because its product page lists a 6 in and a 10 in bit against the single 8 in bit in the VEVOR 43cc kit. Its manual says the bit assembly is bought separately, so confirm the box contents with the seller before you order.
Which weighs less, the VEVOR 43cc or the DC HOUSE 52cc earth auger?
The manuals do not settle which weighs less, because the VEVOR 43cc manual prints 11.9 kg and the DC HOUSE 52cc manual prints 10.4 kg with no stated basis for either. What each figure includes, the bit, the handles or fuel, is unknown, so the figures do not give a comparable carrying weight.
Does the VEVOR 43cc post hole digger have reverse?
The VEVOR 43cc post hole digger manual does not confirm a reverse, and it does not authorize powered reverse for freeing a bit. Complete the full shutdown in the shutdown box above first, and because the manual gives no freeing method after shutdown, contact VEVOR or qualified service for guidance before touching a stuck bit.
Is the VEVOR 43cc earth auger EPA certified?
The VEVOR 43cc earth auger is EPA certified according to its manual, which prints an EPA certificate issued to the manufacturer it names. That certificate does not make a gas engine safe to run indoors, so start and run it outdoors only, because the exhaust contains deadly carbon monoxide that has no color or smell.
References
- Hyson BE, Friedman BM, Spear B, Bishop-Freeman SC. Lethal carbon monoxide generated from small internal combustion engines. J Anal Toxicol. 2024;48(8):625-629.
- Armstrong T, Bir C, Foulke J, Martin B, Finsen L, Sjogaard G. Muscle responses to simulated torque reactions of hand-held power tools. Ergonomics. 1999;42(1):146-159.
- Mazaheri A, Rose LM. Reaction load exposure from handheld powered tightening tools: a scoping review. Int J Ind Ergon. 2021;81:103061.
- Thaper R, Sesek R, Garnett R, Acosta-Sojo Y, Purdy GT. The combined impact of hand-arm vibration and noise exposure on hearing sensitivity of agricultural/forestry workers: a systematic literature review. Int J Environ Res Public Health. 2023;20(5):4276.
- Palmer KT, Bovenzi M. Rheumatic effects of vibration at work. Best Pract Res Clin Rheumatol. 2015;29(3):424-439.
Safety Note: Only an adult who has read the manual and understands the controls should use an earth auger or post hole digger, never a child or anyone tired or impaired. Use the number of people your manual specifies, and keep everyone else out of the work area. The rotating bit can catch hair, clothing and gloves, and it can bind on a root, a rock or a buried object: the machine can then twist or kick in your hands. Stand with firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. If utility contact or a gas leak is suspected, stop work immediately. Do not touch, inspect, free or move the auger or exposed service, and do not attempt the normal hands-on shutdown or disconnect electrical connections in the suspected leak area. Leave the area, keep others away and contact the utility from a safe location; call 911 for a suspected gas leak or immediate danger. Otherwise, release the throttle or trigger immediately if the bit binds or control is threatened, then follow the shutdown procedure. On a two-person unit, both operators must understand the controls and agree on start and stop signals before starting; stop whenever either operator calls stop. Use reverse only where your manual expressly authorizes it. Never touch or clear the bit while it turns. Before you clear or free the bit, change or attach the bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger, complete the shutdown for its power type. Corded electric: release the switch or trigger, wait until the bit has stopped completely, then unplug it from the outlet by the plug, not the cord; before transport or storage, also let the motor cool. Battery: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where the model has one. Gas: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire and secure it away from the plug, and let the engine and muffler cool before touching the bit, engine, muffler or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown instructions in both the bit or attachment manual and the power-head or drill manual. If the bit sticks or material wraps around it, stop and complete the full shutdown before touching or inspecting it. Use only the freeing or clearing method specified in the exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when the exact manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. Wear safety glasses with side shields or goggles meeting the manual’s specification, including ANSI Z87.1 where required; add a face shield where required. Wear hearing protection with gas engines and wherever the manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional footwear protection the manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep them, clothing, hair, hands and feet away from moving parts. Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm that every notified utility has responded with markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Preserve the marks and follow your state’s ticket-validity and tolerance-zone rules. Keep the auger out of the required clearance area; near marks, use careful hand digging or another locating method permitted by state rules and the utility. Follow any stricter prohibition in the auger’s manual. Marks do not show a safe drilling depth. Arrange to locate private irrigation lines, cables and other services that 811 may not cover. If a line’s location remains uncertain, do not dig there. Do not handle or move unidentified cables, pipes or utility lines. Before you start, remove rocks, sticks, wire and loose hoses, and identify irrigation lines, drip lines and sprinkler heads. Keep children, pets and other people out of the work area and at least the distance your exact manual specifies. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs. No single distance is safe for every auger. On a slope or uneven ground, slow down, keep firm footing and follow only your manual’s rule. Do not dig in frozen or rock-hard ground. Before refuelling, complete the full gas shutdown described above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Keep fuel away from smoking, flames, sparks and other ignition sources. Use an approved fuel container, avoid overfilling, secure the cap and follow the manual’s spill-cleanup and restart-location instructions; do not start with a fuel leak. Use the specified fuel and oil arrangement for that engine. Never start or run a gas auger indoors, in a garage or shed, or in an enclosed or poorly ventilated area, even with doors open. Operate outdoors where exhaust cannot accumulate or enter occupied spaces through doors, windows or air intakes. Exhaust contains deadly carbon monoxide. For a corded auger, inspect the cord and extension cord before use and do not use damaged cords or plugs. Use an outdoor extension cord meeting the exact manual’s gauge, length, plug and grounding requirements, and follow its GFCI instructions. Keep connections dry and the cord clear of the bit, heat, oil and sharp edges. Never carry the auger by its cord or wrap the cord around your body. Do not use it in rain or wet conditions prohibited by the manual. Use only manufacturer-approved batteries and chargers for the exact model. Complete the battery shutdown before removing or changing a battery, and keep the switch off and fingers off the trigger when installing one. Do not use damaged or modified batteries or chargers. Keep loose battery terminals away from metal objects, and follow the battery and charger manuals for moisture exposure, charging temperature, cooling and storage. Load and unload only as your manual describes, and store the auger dry and out of children’s reach. Take breaks and stop when you are tired.


