A woman standing beside a stopped electric pressure washer on a patio with a frustrated expression

Why Does My Pressure Washer Keep Shutting Off? Causes and Safe Checks

A pressure washer shuts off for one of three reasons: its design tells it to stop, a protection device has acted, or something that feeds it, such as power, water or oil, has failed. The manuals of named washers show which stops are normal and which need the maker, so the manual’s stop list comes before any repair idea. I treat every machine that holds pressure the way I treat a sprayer on the farm: I find out how it is meant to behave when it stops before I decide it is broken. Below you get the order to check, what each manual prints and the safe steps that come before every check.

Why Does My Pressure Washer Keep Shutting Off?

Start with the group, because each group has a different next step. A stop by design needs no repair, a protection device needs the reset or cool-down your manual describes, and a feed problem needs a look at the cord, the water or the oil. This page covers gas and corded electric washers. A battery washer follows its own manual and battery instructions first. I explain the pump, hose, gun and nozzle in my guide on how a pressure washer works.

  • Stops by design: the motor stops because you released the trigger or the pump has finished pressurizing, and the manual describes that as normal for the model.
  • Protection devices: a GFCI plug, a thermal sensor or overload, a circuit breaker and, on gas washers whose maker lists one, a low-oil shutdown.
  • Feed problems: an extension cord that drops the voltage, a water supply that cannot keep up, air or pressure trapped in the pump, or low oil.

Check in This Order

Read the manual’s stop list for your model first, then look at protection devices, then at power, water and oil. Every hands-on check below starts with the safe-state box, so read the next section before you touch the machine.

I recommend writing down what you see before you change anything: how long the washer ran, whether you were holding the trigger and whether a light or a plug button changed. That one line of notes usually points at a group. If the same stop returns after the manual’s own check, the next step is the maker or a service center, covered in the last section.

Stop and Make Safe Before You Check Anything

A stopped washer is not a safe washer. Pressure can stay trapped in the hose and the gun, a corded washer still has mains power at the plug, and a gas engine and its muffler stay hot after the engine stops. Read the pressure washer’s manual before you connect water or power, and follow it. Its warnings, its operator rules and its steps for your exact model come before anything in this article.

The Safe-State Box

Safe-State Box: Stop and Make Safe

Stop and make safe before you connect or disconnect a hose, change a nozzle, wand or accessory, clear a clogged nozzle, clean a filter, add detergent, refuel, check the oil, charge or change a battery, drain the washer, move it, store it or leave it. Release the trigger and engage the trigger lock on the spray gun. Gas washer: turn the engine off with its switch as the manual says and wait until all moving parts have stopped. Let the engine and the muffler cool for the time your manual gives before you refuel, store the washer or touch hot parts, and disconnect the spark plug wire before maintenance where your manual directs it. Corded electric washer: turn the washer off with its power switch and wait until all moving parts have stopped. Every washer, after the steps above for your type: follow your manual’s water-supply shutdown and pressure-relief procedure. Point the gun away from people, pets and electrical equipment at a discharge location your manual and the detergent label permit. Disengage the trigger lock, squeeze the trigger to relieve the trapped pressure as the manual directs, then engage the lock again. Then unplug a corded washer by the plug, not by the cord, with dry hands, or remove the battery from a battery washer as your manual directs and keep it away from the washer while you work. Do not disconnect hoses or change nozzles before the pressure is relieved. If the manual’s procedure does not release the pressure, stop and get service; do not loosen a fitting to release it. Only then disconnect hoses or change nozzles. Where your manual gives a different order for these steps, follow your manual’s order. Follow every applicable step in your manual, in the order it specifies, and check that every hose, fitting and nozzle is attached and undamaged before water or power goes back on.

Some manuals give their own order, and yours wins where it differs from the box. These are the orders of the models named in this article, each as its manual prints it.

  • Westinghouse ePX3500: turn off the pressure washer, release the pressure in the spray gun and unplug the pressure washer before maintenance.
  • Greenworks GPW3002A: its maintenance line says to shut off the product, wait for all moving parts to stop, disconnect it from the power supply and squeeze the spray gun trigger to release water pressure, while its stop steps release the pressure first and disconnect the cord last.
  • Westinghouse WPX3200, WPX3400 and WPX3600: lock the trigger, move the engine switch to OFF, close the fuel valve, turn the water off, then disengage the lock and depress the trigger for 15 seconds. The WPX3200 and WPX3400 manuals say to let the washer cool at least two minutes before refueling and at least 30 minutes before storage.
  • Simpson PowerShot: set the trigger lock, turn the engine switch to OFF, slide the fuel valve to OFF if equipped, turn off the water supply, then release the trigger lock and squeeze the trigger to relieve the pressure, and let the engine cool completely before handling and storage.

The Short Safety Block for Any Check That Sprays

Some checks below involve squeezing the trigger or running the machine. Each one carries the same short block of rules. I recommend reading the box above aloud once before the first check, the way you would read a pre-spray checklist.

  • Spray: Never point the spray at yourself, another person, a pet or any part of the body. Keep your hands and feet away from the nozzle and the stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. A review of hand injection injuries found a real risk of amputation (1).
  • Protection: Wear safety glasses or goggles and closed footwear when you operate the washer, and put them on before you start; where your manual requires goggles, side shields or a face shield, that requirement replaces the minimum here. Follow the manual’s additional protective-equipment requirements, including hearing protection where the manual requires it, and the detergent label’s requirements when you handle detergent. Keep your hands and feet away from the spray. Protective equipment does not make contact with the stream safe. Kärcher’s K1700 Cube and K1800PS manuals call for properly rated eye protection such as goggles or a face shield and say safety glasses do not provide full protection, and the Westinghouse gas manuals call for safety goggles or safety glasses with side shields, a full face shield as necessary and full ear protection. A case series of three patients hurt by pressure washers reported poor final vision in all three (2).
  • Trigger lock: Engage the trigger lock on the spray gun whenever you stop spraying, even for a moment, before you set the gun down, and before you walk away or change position.
  • Grip and footing: Hold and brace the spray gun as your manual instructs, keep firm footing on a surface that is not slippery, and follow your manual’s warning about the push of the gun when you squeeze the trigger. Start the stream away from your feet and from anyone else, and never swing the gun toward people or pets as you turn. The Westinghouse manuals say to grasp the gun with two hands and warn that the forces from the gun can make you lose footing and fall.
  • Height and runoff: Do not use a pressure washer for a task at height, such as from a ladder, unless your manual expressly permits the equipment and the method. Keep wash water, detergent and debris out of streets, storm drains, ditches and streams.
  • People and pets: Keep children, pets and other people away from the work area while the machine runs, and never let a child use the machine.

Gas Washers: Exhaust Is a Poison Risk

Operate a gas pressure washer outdoors, never inside a building or a partly enclosed space. CDC says to keep it at least 20 feet from any window, door or vent, and your manual may set a stricter placement, which you follow (3). Engine exhaust contains carbon monoxide, which you cannot see or smell and which can kill. A series of fatal cases tied to small engines included a pressure washer in a poorly ventilated space (4). Opening a door or a window does not make it safe to run an engine inside. If anyone develops symptoms such as headache, dizziness, weakness, nausea or confusion, move to fresh air and get emergency medical care. Call 911 for a fire or immediate danger.

Pressure Washer Shuts Off When Trigger Released by Design on Some Models

Many corded washers are built to stop the pump motor when you let go of the trigger, and the manual says so in plain words. If the motor stops the moment you release the trigger and starts again when you squeeze it, read this section before you suspect a fault. A new pressure washer keeps shutting off after a few seconds in this way on several models quoted below.

Total Stop Systems and Trigger-Start Motors

According to Sun Joe, its SPX3000 has a Total Stop System: “When the trigger is released, water stops flowing through the pump. The TSS then automatically turns the motor off.” The SPX3000-XT1 manual adds that it turns the motor off to protect the pump from overheating. Kärcher says the motor of the K1700 Cube “starts when the trigger of the gun is pulled and shuts off when the trigger is released.” My Sun Joe SPX3000 washer review covers that corded washer in detail.

These are printed features of those models, not rules for every washer. Your manual tells you whether yours works this way. If you are choosing a corded model, my roundup of the best electric pressure washers compares their printed specs.

Auto-Start Pumps

Westinghouse describes an auto-start pump in the ePX3500 manual: “The unit will run for several seconds and shut off. This is a normal function of the auto-start feature.” The ePX3100 and WPX3400e manuals carry the same line, and the ePX3500 troubleshooting table says the motor may run 1 to 2 seconds. Greenworks prints an Auto On/Off switch in the GPW2003 manual: the pump pressurizes and shuts down immediately, and the unit turns on once the trigger of the gun is depressed.

Squeezing the trigger rapidly makes the auto-start feature miss an on and off cycle, and the Westinghouse manual says to use slow, deliberate trigger pulls. A washer that seems not to start may simply have missed a cycle. I recommend squeezing once, slowly, and waiting before you squeeze again.

A Quiet Washer Can Still Be Under Pressure

Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. The Westinghouse manual says the unit could be pressurized even if you cannot hear the motor and pump running, so treat every stopped corded washer as pressurized until you complete the box.

Worked example: an ePX3500 runs for 1 to 2 seconds after you switch it on and then goes quiet. That matches the troubleshooting line above, so the next move is a slow squeeze of the trigger, not a repair. If the same washer stops again while you hold the trigger, move on to the protection devices in the next section. I put the design check first because it costs nothing and removes the most worry.

Electric Pressure Washer Keeps Shutting Off From Protection Devices

When the stop is not in the design, a protection device is the next suspect. A GFCI plug cuts power when it senses a fault, a thermal sensor or overload cuts the motor when it runs hot, and a breaker trips on an overloaded circuit. The callout below is the floor for every corded washer.

Corded Electricity: The Floor

Use the electrical supply and the GFCI protection your manual specifies, and test the GFCI before use according to its instructions. If the washer trips a GFCI or a circuit breaker while you use it, stop using it and have a qualified repair person examine it before you use it again; do not keep resetting it and carry on. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Never cut or splice a power cord or an extension cord. Wear closed, rubber-soled footwear that gives some electrical insulation, plus any additional footwear the manual requires; footwear does not replace GFCI protection or the other electrical precautions. Use an extension cord only if your manual permits it, and then only the type and length it names. Keep every plug and cord connection dry, out of standing water and away from runoff and the area you are washing, and keep the spray away from outlets, wiring and electrical equipment. Do not use a damaged cord or plug.

GFCI Trips and Resets

If the washer trips a GFCI or a circuit breaker while you are using it, stop using it and have a qualified repair person examine it before you use it again. CDC gives the same direction for a breaker: have a qualified electrician check the pressure washer after it has tripped a circuit breaker, and always test the GFCI before use (3).

The reset button has a different job in the manuals. It belongs to the pre-use routine, when you plug the washer in and test the GFCI as your manual directs. A trip during work is the case above, and the answer is not to keep resetting it and carry on. I recommend keeping a note of when the washer tripped and what you were doing, so the repair person has the history.

  • Ryobi RY141612: if a Ryobi pressure washer keeps shutting off or will not start, the troubleshooting table lists a tripped GFCI plug and the house breaker. The manual asks you to press the reset button each time you connect the washer to the power supply and to test the GFCI monthly. My review of the Ryobi RY141612 covers that corded washer in detail.
  • CRAFTSMAN CMEPW1900 and CMEPW2100: the table lists a tripped GFCI among the causes of a motor that does not start and names the reset button on the plug end of the cord. I cover that washer in my review of the CRAFTSMAN CMEPW2100.
  • Kärcher K1700B and K1800PS: the table lists a tripped GFCI and a tripped breaker among the causes of a washer that will not start.
  • WORX WG605 and WG602: the table lists a tripped GFCI plug among the causes of a washer that does not start.

The GFCI test is the one powered check in this article, and it follows your manual’s own steps. Ryobi’s manual says to press the TEST button, which should click and put the light out, and then to press RESET to restore power. It also says that GFCI plugs do not protect against short circuits, overloads or shocks. Every other check here starts from the safe-state box.

Sun Joe Pressure Washer Keeps Shutting Off From the Thermal Sensor

Sun Joe prints a thermal sensor in the SPX3000 and SPX3000-XT1 manuals. The manual says the machine will restart after a few minutes when the thermal sensor has cooled, and the troubleshooting table says to leave the washer for 5 minutes to cool down. My comparison of the SPX3000 and the SPX3000-XT1 sets the kit, figures and safety side by side.

That wait is Sun Joe’s figure for those two models only. I recommend using it to switch the washer off and complete the safe-state box above, not to keep squeezing the trigger. Kärcher’s K1700B and K1800PS manuals list a thermal overload that resets by itself once the unit cools. Where a manual prints a self-reset, wait as it says; where it prints nothing, contact the maker.

Greenworks Pressure Washer Keeps Shutting Off From Breaker or Buzzing

The Greenworks GPW3002A manual lists a tripped circuit breaker among the causes of a motor that will not start. A breaker that tripped while you were using the washer falls under the rule above: stop using it and have it examined.

For a buzzing motor, the GPW3002A manual lists low voltage, residual pressure and voltage loss from an improper extension cord, and the GPW2003 manual lists residual pressure as well. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. The GPW2003 manual then describes squeezing the trigger on the spray wand to release that pressure.

When the Power Supply Cuts Out an Electric Washer

A long cord or a weak circuit can starve the motor, and the manuals say so. A yard far from an outlet is the usual reason people reach for an extension cord, so I recommend reading your manual before buying one and comparing the alternatives in my guide to battery and corded pressure washers. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above.

  • Sun Joe SPX3000: “It is not recommended to use an extension cord with this pressure washer.” The manual says a cord may cause a drop in line voltage resulting in loss of power and overheating.
  • CRAFTSMAN: the troubleshooting table tells the owner whose motor buzzes to plug directly into the outlet, while the manual’s extension cord section appears elsewhere. Follow the manual’s ban in its safety rules.
  • Kärcher K1700 Cube: the manual says not to use an extension cord with the product and to connect it to an individual branch circuit only. I go through that washer in my review of the K1700 Cube.
  • Greenworks GPW3002A: the troubleshooting table lists voltage loss from an improper extension cord as a cause of a buzzing motor. My Greenworks 3000 PSI washer review covers that model in detail.

Sun Joe’s manual also says power cords on drums should be completely unwound so they do not overheat. Use an extension cord only if your manual permits it, and then only the type and length it names.

Gas Pressure Washer Keeps Shutting Off Over Oil and Heat

A gas washer adds an engine to the list of things that can stop, and my roundup of the best gas pressure washers compares gas models on engine and soap system. The engine’s own manual is the authority for the engine, and a washer manual covers the pump and the parts around it. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above.

Oil Level and Low-Oil Shutdown

According to Simpson’s product pages, the PowerShot PS3228 and the Clean Machine CM61456 have a low-oil shutdown. Westinghouse’s WPX3200 and WPX3400 manuals treat low oil as a reason the engine will not start, and the WPX3600 manual lists inspecting the engine and pump oil before each use. I recommend checking the oil before you start the engine every time, as that manual says. My comparison of the WPX3400 and WPX3200 sets those two gas washers side by side.

Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Do the oil check on a level surface with the engine off and cool, and add only the oil your manual names. Any engine fault beyond the oil level goes to the engine maker or a service center.

The Pump Heat Limit

A gas washer that runs with the trigger released builds heat in the pump. The Simpson PowerShot manual says that more than two minutes without the trigger pulled will overheat the pump and possibly cause damage, and that the thermal relief valve will open and spray water. It says to shut off the engine if the washer will not be used for longer than two minutes.

The valve spraying water is the pump protecting itself, and the manuals do not describe it as the engine shutting down. I recommend setting the trigger lock and switching the engine off whenever you stop for longer than your manual’s limit.

What the gas manuals print about running without spraying
Model Printed limit with the trigger not pulled
Simpson PowerShot More than two minutes overheats the pump; the thermal relief valve opens
Westinghouse WPX3200 and WPX3400 More than one minute builds heat; the thermal relief valve opens

Never tamper with the thermal relief valve, as Simpson’s manual says.

An Engine That Starts Briefly and Stops

Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. The Westinghouse WPX manual then says that if the engine starts briefly and shuts off, you squeeze the trigger on the spray gun to relieve the pressure before trying to start the engine again. Simpson’s manual also warns that turning off the water supply to the pump with the engine running will damage the pump.

Check the Water Supply and Trapped Air

Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. The manuals tie the water supply and trapped air to weak pressure and to pump damage, and the order of connecting and purging comes first in every one.

  • Water first: Connect the hoses and turn on the water before you start the machine, and purge and start it in the order your manual specifies.
  • Simpson: the manual asks for an uninterrupted source of clean, cold water at a minimum of 5 gallons per minute and 20 PSI, says that running the pump without water will severely damage the pump seals and other internal components, and says to hold the trigger for at least 30 seconds or until the water runs steady and the air is purged.
  • Westinghouse WPX3600: the manual says not to start the engine until a steady stream of water flows from the nozzle, and never to connect a garden hose without the inlet screen in place. My guide on starting a gas pressure washer follows the steps from two maker manuals.

I treat the water supply as something to confirm, not assume, especially from a well or a tank. Check the inlet screen only after the box above, and replace a damaged high-pressure hose; never repair or patch it. When the stream is weak, my guide on a pressure washer losing pressure lists the causes the manuals give.

When to Stop and Contact the Maker

Owner checks end where the manual’s checks end. A repair beyond them belongs to the maker or a service center.

  1. A GFCI or breaker that tripped while you were using the washer: stop using it and have a qualified repair person examine it before you use it again; CDC gives the same direction for a tripped circuit breaker.
  2. A plug or cord that needs replacing: use only identical replacement parts, and for a GFCI plug parts that include GFCI protection, as the Ryobi, Westinghouse and Greenworks manuals say.
  3. A hose that leaks or a fitting that weeps: stop, complete the box and replace a damaged high-pressure hose rather than repairing it.
  4. An engine fault beyond oil level: contact the engine maker or a service center.
  5. A thermal relief valve or safety valve: leave it alone and contact the maker if it keeps opening.

Read the Stop List Before You Reach for Tools

Three things are worth remembering. The stop may be in the design, so read what your manual prints first. A GFCI or breaker that trips while you work is a reason to stop and have the washer examined, not to keep trying. Oil, water and the cord cost nothing to check once the machine is safe. If the motor does not start at all, my guide on a pressure washer that won’t start lists the manual checks.

My own tip is to keep the manual’s stop page next to the washer so you can read it with the machine switched off. Next, go back to the safe-state box before every hands-on step. A pressure washer that keeps shutting off is giving you a clue, and the manual for your model is the first place to read what the clue means. My answer to “how to start an electric pressure washer” shows how the manuals set the start order.

Frequently Asked Questions

Why does a pressure washer shut off when the trigger is released?

A pressure washer shuts off when the trigger is released because many corded models are built to stop the motor at that moment. Sun Joe says its Total Stop System turns the motor off when the trigger is released, and Kärcher says the K1700 Cube motor shuts off when the trigger is released.

Why does my electric pressure washer keep shutting off?

An electric pressure washer keeps shutting off when its design, a protection device or its power supply stops it. The manuals list a tripped GFCI plug, a thermal sensor that needs time to cool, a tripped breaker and an extension cord that drops the voltage. If it tripped a GFCI or a breaker while you were using it, stop using it and have a qualified repair person examine it before you use it again.

Why does my gas pressure washer keep shutting off?

A gas pressure washer can shut off when the oil is low on a model whose maker lists a low-oil shutdown. Before you check the oil, complete the stop and make-safe steps for your pressure washer in the safe-state box above, then check it as your manual directs. Contact the engine maker or a service center for any other engine fault.

Why does my pressure washer shut off when it gets hot?

A pressure washer that shuts off when it gets hot may have a thermal sensor or overload that has acted. Sun Joe says its sensor restarts the machine after a few minutes once cooled, and Kärcher’s K1700B and K1800PS manuals say the thermal overload resets by itself. Follow your manual’s wait, and stop using the washer if it keeps stopping.

Why does my pressure washer run for a few seconds then shut off?

A pressure washer that runs for a few seconds and then shuts off may be an auto-start model working as designed. Westinghouse’s ePX3500 manual says the unit will run for several seconds and shut off, and calls that a normal function of the auto-start feature. If your manual does not describe this for your model, contact the maker.

References

  1. Hogan CJ, Ruland RT. High-pressure injection injuries to the upper extremity: a review of the literature. J Orthop Trauma. 2006;20(7):503-511.
  2. Placide J, Yang MY, Gross AW, Crowell EL. Case series: traumatic ocular lacerations secondary to pressure washers. Am J Ophthalmol Case Rep. 2022;27:101612.
  3. Centers for Disease Control and Prevention. Pressure washer safety. Natural Disasters. Published May 15, 2024.
  4. Hyson BE, Friedman BM, Spear B, Bishop-Freeman SC. Lethal carbon monoxide generated from small internal combustion engines. J Anal Toxicol. 2024;48(8):625-629.

Safety Note: Read your pressure washer’s manual before you connect water or power, and follow it. Never point the spray at yourself, another person, a pet or any part of the body. Keep hands and feet away from the nozzle and stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. Wear safety glasses or goggles and closed footwear before operating the washer, plus any additional protection required by the manual and the detergent label. Follow the manual’s instructions for the trigger lock, grip, footing and recoil, and engage the trigger lock whenever you stop spraying. Use only the nozzles, accessories and detergents the manual permits, and never point any nozzle at skin, people or animals. Do not perform a task at height without instructions expressly permitting the equipment and method in the exact manual. Gas models: operate outdoors, never inside a building or a partly enclosed space. Keep the engine at least 20 feet from any window, door or vent, following CDC’s pressure washer guidance and any stricter manual requirement. Exhaust contains carbon monoxide, which cannot be seen or smelled and can kill. Opening doors or windows does not make indoor operation safe. Refuel only with the engine off and cool, following the manual. Corded models: use the manual’s specified electrical supply and GFCI protection, and test the GFCI before use according to its instructions. After an operating GFCI or breaker trip, do not reuse the washer until a qualified repair person has examined it. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Wear closed, rubber-soled footwear that provides some electrical insulation, plus any additional footwear required by the manual; footwear does not replace GFCI protection or the other electrical precautions. Never cut or splice cords. Use an extension cord only as the manual permits. Keep connections dry and away from runoff, standing water and the washing area, and keep spray away from electrical equipment. Battery models: use only the battery and charger the maker specifies for your exact model. Emergency first: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Otherwise, complete the applicable stop and make-safe procedure before hose, nozzle, wand or accessory work, clearing a blockage, cleaning, maintenance, refueling, checking oil, adding detergent, battery changes or charging, draining, moving, transporting, storing or leaving the washer. Follow your exact manual’s procedure and order. Release the trigger and engage its lock. Gas: switch the engine off and wait for it to stop; disconnect the spark plug wire before service as the manual directs, and let hot parts cool before refueling, storage or contact. Corded: switch off and unplug by the plug with dry hands. Battery: switch off, remove a removable battery as the manual directs and keep it away while working; for a built-in battery, follow the manual’s isolation procedure and do not open the battery compartment. Complete the manual’s water-supply shutdown and pressure-relief steps: point the gun in a safe direction at a permitted discharge location, disengage the trigger lock, squeeze the trigger as directed to relieve pressure, then reengage the lock. Do not disconnect hoses or change nozzles until pressure is relieved. If pressure cannot be relieved by the prescribed procedure, obtain service without loosening fittings. Refit and inspect parts before restoring water or power. Replace a damaged high-pressure hose; never repair or patch it. Before you wash, plan how to keep wash water, detergent and debris out of streets, storm drains, ditches and streams, and check with your city or county stormwater office about collection and disposal. Send wash water to landscaping only where local rules and the detergent label permit it and the soil can absorb it without runoff or contamination. Keep children and pets away, and never let a child use the machine. Drain and store the washer as its manual directs. For exposure to a cleaning product, follow the label’s first-aid instructions and call Poison Control at 1-800-222-1222. Call 911 for a fire or immediate danger.

Scroll to Top