A pressure washer works by using a motor or engine to drive a pump that raises the pressure of garden hose water, then sending that water through a high-pressure hose to a spray gun, a wand and a nozzle. The nozzle shapes the stream you see. I look at a washer’s inlet screen the way I look at the 150-mesh disc filter at the pump head of the drip system I built: a small part that protects the pump. Below I follow the water part by part, from the faucet to the nozzle.
How Does a Pressure Washer Work?
A pressure washer is a pump with a motor or engine behind it, a garden hose in front of it and a trigger gun at the far end. The water makes six stops on the way, and I list them in order so you can match each one to a part of your own machine.
- Garden hose: water arrives from your faucet through an ordinary garden hose.
- Inlet screen: the Westinghouse and Greenworks manuals describe a screen at the water inlet that you inspect before you connect the hose.
- Pump: a motor or an engine drives the pump, which raises the pressure of the water.
- High-pressure hose: the pressurized water leaves the pump and travels through a hose built for it.
- Trigger gun: the trigger decides whether water flows out through the wand.
- Nozzle: the nozzle at the tip of the wand gives the stream its shape, and your manual names the nozzles that belong to your machine.
Everything else on the machine, from an auto-start switch to a detergent tank, hangs off one of those six stops. A pump only works on water that is already there, so the order of the steps matters as much as the parts. I recommend reading the parts list in your manual before you connect anything, because makers name the parts differently.
Where the Water Comes In Through the Hose and Screen
The pump needs a supply of water before it does anything else. Kärcher says its pumps need water to work correctly, and a garden hose provides it. Connecting that hose is the first hands-on job, so the full safe-state box comes first.
Safe-State Box: Stop and Make Safe
Emergency first, for a washer with a battery: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Stop and make safe before you connect or disconnect a hose, change a nozzle, wand or accessory, clear a clogged nozzle, clean a filter, add detergent, refuel, check the oil, charge or change a battery, drain the washer, move it, store it or leave it. Release the trigger and engage the trigger lock on the spray gun. Gas washer: turn the engine off with its switch as the manual says and wait until all moving parts have stopped. Let the engine and the muffler cool for the time your manual gives before you refuel, store the washer or touch hot parts, and disconnect the spark plug wire before maintenance where your manual directs it. Corded electric washer: turn the washer off with its power switch and wait until all moving parts have stopped. Battery washer: turn the washer off and wait until all moving parts have stopped. Every washer, after the steps above for your type: follow your manual’s water-supply shutdown and pressure-relief procedure. Point the gun away from people, pets and electrical equipment at a discharge location your manual and the detergent label permit. Disengage the trigger lock, squeeze the trigger to relieve the trapped pressure as the manual directs, then engage the lock again. Then unplug a corded washer by the plug, not by the cord, with dry hands, or remove the battery from a battery washer as your manual directs and keep it away from the washer while you work. Do not disconnect hoses or change nozzles before the pressure is relieved. If the manual’s procedure does not release the pressure, stop and get service; do not loosen a fitting to release it. Only then disconnect hoses or change nozzles. Where your manual gives a different order for these steps, follow your manual’s order. Follow every applicable step in your manual, in the order it specifies, and check that every hose, fitting and nozzle is attached and undamaged before water or power goes back on.
Inspect, Flush and Connect
Read the pressure washer’s manual before you connect water or power, and follow it. Its warnings, its operator rules and its steps for your exact model come before anything in this article. Before you inspect parts or connect hoses, complete the applicable stop and make-safe steps in the safe-state box. Inspect the high-pressure hose, the spray gun and every fitting before each use, as your manual describes, and do not use a damaged part.
Replace a damaged high-pressure hose; never repair or patch it. Connect the hoses and turn on the water before you start the machine, and purge and start it in the order your manual specifies.
The manuals show how much the details differ from one model to the next. Compare the three below, and follow your own. When you are ready to pick a machine, my best pressure washer roundup lists nine gas, electric and battery models.
| Model | Before you connect | Inlet screen or filter | Water limit as printed |
|---|---|---|---|
| Greenworks 2000 PSI electric (GPW2003) | Let water run through the garden hose for 30 seconds; keep at least 10 feet of free hose between faucet and inlet | Inspect the intake screen; do not use the machine if it is damaged | Maximum inlet water temperature 104 degrees F (40 degrees C) |
| Greenworks 3000 PSI brushless (GPW3002A) | Let water run through the garden hose for 30 seconds; keep at least 10 feet of free hose between faucet and inlet | Inspect the inlet filter; do not use the machine if it is damaged | Maximum inlet water temperature 104 degrees F (40 degrees C) |
| Westinghouse ePX3500 | Flush the hose for several seconds | Inspect the screen in the water inlet; never connect a garden hose without the screen in place | Cold water only |
Why the Water Goes On Before the Power
Westinghouse puts it plainly: always turn the water supply on before you turn the pressure washer power on, because running the pump dry of water will damage the internal components. The same manual says never to let the pump run for more than one minute after you have turned off the water supply. I recommend treating this as the one order you never reverse, and reading your manual’s version of it before every first start.
The Motor or Engine That Drives the Pump
Gas, corded electric and battery washers differ in what turns the pump, and the water path after the pump is the same in outline. Each type brings its own hazard, so each gets its own safety lines below. My comparison of gas and electric pressure washers sets fuel, cord and care side by side.
Gas Engine
A gas washer uses a small gasoline engine in place of a motor to drive the pump. The engine and the muffler stay hot after you stop it, and the exhaust is the larger danger.
Operate a gas pressure washer outdoors, never inside a building or a partly enclosed space. CDC says to keep it at least 20 feet from any window, door or vent, and your manual may set a stricter placement, which you follow.
Engine exhaust contains carbon monoxide, which you cannot see or smell and which can kill. Opening a door or a window does not make it safe to run an engine inside. If anyone develops symptoms such as headache, dizziness, weakness, nausea or confusion, move to fresh air and get emergency medical care.
Corded Electric Motor
A corded washer drives the pump with an electric motor. Westinghouse says to plug the ePX3500 into a grounded 120 volt outlet. According to Greenworks, its 2000 PSI electric model uses a universal motor on 120 volts, 60 hertz and 14 amps, and its power cord carries a GFCI plug. Westinghouse lists its ePX3500 at 120 volts AC and 13 amps, with the GFCI built into the plug of the power cord. If yours is corded, I walk through starting an electric pressure washer with the manual steps and safety checks.
Use the electrical supply and the GFCI protection your manual specifies, and test the GFCI before use according to its instructions. If the washer trips a GFCI or a circuit breaker while you use it, stop using it and have a qualified repair person examine it before you use it again; do not keep resetting it and carry on.
Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Never cut or splice a power cord or an extension cord. Wear closed, rubber-soled footwear that gives some electrical insulation, plus any additional footwear the manual requires; footwear does not replace GFCI protection or the other electrical precautions.
Greenworks says to keep all connections dry and off the ground. Westinghouse says never to use an extension power cord with the ePX3500.
Use an extension cord only if your manual permits it, and then only the type and length it names. Keep every plug and cord connection dry, out of standing water and away from runoff and the area you are washing, and keep the spray away from outlets, wiring and electrical equipment. Do not use a damaged cord or plug.
Battery Pack
A battery washer runs on a battery pack in place of a cord or an engine. The maker of your exact model decides which battery and charger belong to it and how to charge and store them. I set out what the manuals print for battery and corded electric washers in a separate comparison.
Use only the battery and the charger the maker specifies for your exact pressure washer, and charge, store and handle them only as your manual describes. Before you change or charge the battery, follow the emergency exception and the applicable stop and make-safe steps in the safe-state box. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger. If you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a battery, stop using it and follow your battery manual’s emergency instructions.
Inside the Pump
The pump raises the pressure, and makers build it in different ways. Kärcher describes one design for one of its electric washers, and I start there.
One Maker’s Pump Design
According to Kärcher, the motor turns a wobble plate that moves three pistons up and down, and each piston works with one suction valve and one pressure valve. On the downstroke, water is drawn through a suction valve into the piston chamber. When the piston moves up, the water is pushed through a pressure valve toward the injector, where cleaning agent is added if you use it. Kärcher adds that the water first flows through a double-walled casing around the motor, which the company says cools the motor, reduces noise and extends run time.
Pump designs differ between makers, so read this as one maker’s design and not as a rule for every washer. The Simpson manual for one of its gas washers says only that the pump is maintenance free and needs no oil.
What Hurts a Pump
Two things in the manuals matter more than the design. A pump that runs without water takes damage, which is why Westinghouse tells you to turn the water on first. Freezing damages the pump too: Westinghouse says the high-pressure pump will crack when the water freezes and expands, and its label says not to store the machine where the temperature could drop below 40 degrees F (4.5 degrees C). Before you drain, move or store a washer, complete the stop and make-safe steps in the safe-state box above.
I keep a simple rule from my own work: protect the pump first and ask questions about the nozzle later. Water, a clean screen and a frost-free place cover most of it. Causes from the manuals sit in my answer to “why is my pressure washer losing pressure”.
The Unloader, Bypass and Thermal Relief Valve
A pump keeps moving water as long as the motor or engine runs, so a washer needs a way to deal with the water when you release the trigger. The Simpson manual for one of its gas washers describes how that maker handles it, and a thermal relief valve protects the pump from heat.
Bypass Mode
According to Simpson, bypass mode lets water re-circulate within the pump when the gun trigger is not pulled, so you can release the trigger without shutting off the engine. The same manual warns against running the unit for more than two minutes without pulling the trigger, because that can overheat and damage the pump. It says the pressure setting is preset at the factory and that a higher setting than the factory pressure may damage the pump.
Westinghouse’s manual for its gas washers lists an unloader valve and says it controls pressure output. Your manual names the valves on your model and says what, if anything, you may adjust. I leave that setting alone and send questions about it to the maker.
Thermal Relief Valve
Simpson describes a thermal relief valve that opens when the temperature inside the pump rises too high, releases a gush of water to lower it, and then closes. The manual notes that the valve’s location varies with the pump type. Greenworks describes a thermal protector for the pump on its 3000 PSI brushless model that releases a small amount of water, and prints 140 degrees F as the opening temperature. If water appears under a machine you did not expect to leak, stop and complete the safe-state box before you look closer, then read the manual for where your model’s relief valve is.
Auto Start and Stop on Electric Washers
Some corded washers start and stop the motor for you. Greenworks and Westinghouse both print the feature in their manuals, and it changes how you should treat a washer that sounds off. My answer to “why does my pressure washer keep shutting off” lists the safe checks for a washer that cuts out.
Greenworks says that with its 2000 PSI electric model’s power switch in the on position, the pump pressurizes and shuts down, and the unit starts again when you press the gun’s trigger. Westinghouse says the ePX3500 motor will run for several seconds and shut off, which it calls a normal function of the auto-start feature. Squeezing the trigger rapidly makes the unit miss an on and off cycle, so the manual asks for slow, deliberate trigger pulls. Westinghouse also says the motor may run intermittently while the pump primes, and that you should turn the washer off after five minutes of inactivity.
A Quiet Washer Can Still Be Under Pressure
Greenworks says the pressure washer may be on and the system may have pressure even when you cannot hear the pump or motor running. Westinghouse says the unit could be pressurized even if you do not hear the motor and pump running. Treat a silent washer as live until you have completed the stop and make-safe steps in the safe-state box.
The High-Pressure Hose, Trigger Gun and Wand
The high-pressure hose carries the water from the pump to the gun, and the gun is where you control the stream. These are the parts that take the pressure, and they are where the stream becomes dangerous.
The Hose
A University of California safety note says never to repair a damaged high-pressure hose and always to replace it. Westinghouse says never to disconnect the high-pressure hose from the washer while the system is pressurized, and to examine the hose regularly and replace it if it is damaged. Before you disconnect or replace a hose, complete the stop and make-safe steps in the safe-state box.
Trigger, Lock and Wand
The trigger opens the path for water to flow from the hose to the wand, and the trigger lock stops it from opening. Engage the trigger lock on the spray gun whenever you stop spraying, even for a moment, before you set the gun down, and before you walk away or change position. Disengage the lock only for controlled spraying or for the manual’s pressure-relief procedure, with the gun pointed in a safe direction. The lock’s name, place and direction of movement are in your manual; Westinghouse and Greenworks each print their own.
Hold and brace the spray gun as your manual instructs, keep firm footing on a surface that is not slippery, and follow your manual’s warning about the push of the gun when you squeeze the trigger. Start the stream away from your feet and from anyone else, and never swing the gun toward people or pets as you turn. Greenworks says to expect the trigger handle to move when the trigger is pulled, because of reaction forces. A Westinghouse label reads that the spray gun kicks back and that you should hold it firmly with two hands.
The Stream and Your Body
Never point the spray at yourself, another person, a pet or any part of the body. Keep your hands and feet away from the nozzle and the stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury.
A case report from Japan describes a pressure washer injection injury that can lead to infection, compartment syndrome and in some cases amputation, even when the wound looks minor (1). A US emergency department analysis covering 2012 to 2021 found that pressure washers caused most of the hand injection injuries it counted (2). One case report describes a finger injured at close range at a car wash: the X-ray showed no fracture, and the finger still needed emergency surgery (3).
The eyes are at risk too. A case series of three patients with eye lacerations from pressure washers reports that all three needed surgery and all had poor final vision (4). A literature review of high-pressure injection injuries to the upper extremity found real amputation risk, and it shows that a small wound can hide a serious injury (5).
Wear safety glasses or goggles and closed footwear when you operate the washer, and put them on before you start; where your manual requires goggles, side shields or a face shield, that requirement replaces the minimum here. Follow the manual’s additional protective-equipment requirements, including hearing protection where the manual requires it, and the detergent label’s requirements when you handle detergent. Keep your hands and feet away from the spray. Protective equipment does not make contact with the stream safe.
Nozzles and the Detergent Draw
The nozzle at the end of the wand is where the stream takes its shape, and the detergent system is where the water takes on something besides pressure. Both are changed by hand, so both start with the safe-state box.
Quick-Connect Nozzles
Westinghouse lists quick-connect nozzles for the ePX3500 at 0, 15 and 25 degrees, plus a soap nozzle and a turbo nozzle, and says to push a nozzle in until it clicks and pull the collar back to remove it. Greenworks lists a 25 degree tip, a 40 degree tip, a black soap tip and a turbo nozzle for its 2000 PSI electric model, and describes the turbo nozzle as rotating in a zero-to-15-degree spray pattern. Simpson describes a 5-in-1 multi-tip nozzle with five settings that you select by rotating a selector. The manual of your model names the nozzle for the job. My guide explains pressure washer nozzle colors and what each maker prints.
Use only the nozzles and accessories your manual permits, following its instructions for the job. Never direct any nozzle at skin, people or animals. Before you change a nozzle, complete the stop and make-safe steps in the safe-state box.
How Detergent Gets Into the Water
Makers build the detergent path differently. Kärcher describes an injector, where cleaning agent is added to the water if required.
Simpson describes a detergent tank that feeds cleaning agents into the pump to mix with the water. Westinghouse says the ePX3500’s onboard soap tank applies detergent only through the soap nozzle, under low pressure. Greenworks says detergent can be applied only when the black soap nozzle is installed on its 3000 PSI brushless model, and that its washer cannot apply soap under high pressure.
Before you add detergent or connect or adjust a detergent accessory, complete the applicable stop and make-safe steps in the safe-state box.
Use only the detergents your manual allows, through the detergent system the manual describes, and read the detergent label before you open it. Wear the protective equipment the detergent label requires, and avoid contact of detergent with your eyes and skin. Do not run a detergent that your manual does not name through the pump. Greenworks adds that household detergents, acids, alkalines, bleaches, solvents and flammable materials can damage the pump.
My plant protection training taught me to read a product label before I open the container, and I read a washer’s manual in the same order. My guide to using a pressure washer follows the manuals’ instructions step by step.
Why Pressure Stays in the System After You Stop
A washer can be switched off and still hold pressure in the hose and the gun. A University of California safety note says to pull the spray-wand trigger after turning the washer off, to release the water pressure in the hose. Your manual gives the exact procedure for your model, and the last paragraph of the safe-state box above gives its order.
When the Stream Pulses
A stream that pulses or cuts in and out is a sign to stop. Before you do anything else, complete the stop and make-safe steps in the safe-state box above.
Greenworks says that if its 2000 PSI electric model pulsates and the stream is intermittent, you turn the washer off and keep bleeding air out of the system. The same manual says a pulsing feeling while you squeeze the trigger may come from a clogged or dirty spray tip, and its troubleshooting table lists a pump that is sucking air. The Greenworks 3000 PSI brushless manual lists a pump drawing in air and says to purge the pump by squeezing the trigger.
A nozzle that gives a weak, uneven or pulsing stream may be blocked. Complete the stop and make-safe steps in the safe-state box, then clear the nozzle only with the tool and the method your manual describes. Never look into the nozzle or point it at anyone to check it.
When a washer pulses, leaks or stalls, I stop first and look second, and I start again only on the conditions in the manual. Manual checks are in my answer to “why is my pressure washer pulsing”.
What the Ratings on the Label Tell You
Makers print a pressure rating in PSI and a flow rating in gallons per minute, and each maker chooses its own basis words. Read the word next to each number, because peak, rated, maximum and up to describe different conditions.
| Model | Pressure as printed | Flow as printed |
|---|---|---|
| Westinghouse ePX3500 | Peak pressure 2500 PSI; rated max pressure 2000 PSI | Maximum 1.76 US GPM; rated 1.24 US GPM |
| Greenworks 2000 PSI electric (GPW2003) | Maximum 2000 PSI | Rated 1.2 GPM |
| Greenworks 3000 PSI brushless (GPW3002A) | Maximum 3000 PSI | Maximum 2.0 GPM; rated 1.1 GPM |
Each figure sits on its own maker’s basis, and the bases do not line up across makers, so the three rows are not a ranking. What each rating means is covered in my guide to PSI versus GPM ratings, and your manual and the label of whatever you wash decide the rest.
What to Check Before You Connect the Water
The pump needs water before power, and a silent washer can still hold pressure. The manual of your exact model names every part and every setting. My tip: read the stop and make-safe steps once on a quiet day, before the washer is out of its box. That order is how a pressure washer turns a garden hose into the stream you control.
Frequently Asked Questions
What makes a pressure washer work?
A pressure washer works because a motor or engine drives a pump that raises the pressure of the water from your garden hose. That water then travels through a high-pressure hose to a gun, a wand and a nozzle, which shapes the stream. The manual of your model names each part and the order for starting it.
How does a pressure washer pump work?
A pressure washer pump raises the pressure of the water that the motor or engine drives through it. Kärcher describes one design in which a wobble plate moves three pistons up and down, each with a suction valve and a pressure valve, and other makers use their own designs. A pump takes damage when it runs without water, which is why Westinghouse says to turn the water on before the power.
How does an unloader valve work on a pressure washer?
An unloader valve controls pressure output, according to the parts list in Westinghouse’s manual for its gas washers. Simpson describes a separate bypass mode that lets water re-circulate within the pump when the gun trigger is not pulled, and it warns against running more than two minutes that way. Your manual names the valves on your model and says whether you may adjust them, and I recommend you leave the factory setting alone.
How does the soap dispenser work on a pressure washer?
The soap dispenser on a pressure washer is a tank or an injector that adds detergent to the water, and each maker’s manual describes its own. Westinghouse and Greenworks print that the soap tanks on the models named here work only through the soap nozzle at low pressure, and Kärcher describes an injector that adds cleaning agent. Use only the detergents your manual allows, since Greenworks warns that household detergents, acids, alkalines, bleaches and solvents can damage the pump.
How does a gas pressure washer work?
A gas pressure washer works like any other pressure washer, except that a small gasoline engine drives the pump in place of a motor. It runs outdoors only, because engine exhaust contains carbon monoxide, and CDC says to keep it at least 20 feet from any window, door or vent. Your manual may set a stricter placement, and you follow it.
References
- Funato N, Sugizaki Y, Ri Y, Ichibayashi R. High-pressure injection damage caused by a high-pressure washer. Cureus. 2024;16(1):e52498. doi:10.7759/cureus.52498
- Johnson C, Newton W, LaRochelle L, Allen J, Daly C. High-pressure injection injuries of the hand in community and industrial settings: incidence and trends. Hand (N Y). 2025;20(6):917-922. doi:10.1177/15589447231218404
- Choi JH, Choi SY, Hwang JH, Kim KS, Lee SY. Finger compartment syndrome due to a high-pressure washer injury: a case report. World J Clin Cases. 2023;11(13):3017-3021. doi:10.12998/wjcc.v11.i13.3017
- Placide J, Yang MY, Gross AW, Crowell EL. Case series: traumatic ocular lacerations secondary to pressure washers. Am J Ophthalmol Case Rep. 2022;27:101612. doi:10.1016/j.ajoc.2022.101612
- Hogan CJ, Ruland RT. High-pressure injection injuries to the upper extremity: a review of the literature. J Orthop Trauma. 2006;20(7):503-511. doi:10.1097/00005131-200608000-00010
Safety Note: Read your pressure washer’s manual before you connect water or power, and follow it. Never point the spray at yourself, another person, a pet or any part of the body. Keep hands and feet away from the nozzle and stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. Wear safety glasses or goggles and closed footwear before operating the washer, plus any additional protection required by the manual and the detergent label. Follow the manual’s instructions for the trigger lock, grip, footing and recoil, and engage the trigger lock whenever you stop spraying. Use only the nozzles, accessories and detergents the manual permits, and never point any nozzle at skin, people or animals. Do not perform a task at height without instructions expressly permitting the equipment and method in the exact manual. Gas models: operate outdoors, never inside a building or a partly enclosed space. Keep the engine at least 20 feet from any window, door or vent, following CDC’s pressure washer guidance and any stricter manual requirement. Exhaust contains carbon monoxide, which cannot be seen or smelled and can kill. Opening doors or windows does not make indoor operation safe. Refuel only with the engine off and cool, following the manual. Corded models: use the manual’s specified electrical supply and GFCI protection, and test the GFCI before use according to its instructions. After an operating GFCI or breaker trip, do not reuse the washer until a qualified repair person has examined it. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Wear closed, rubber-soled footwear that provides some electrical insulation, plus any additional footwear required by the manual; footwear does not replace GFCI protection or the other electrical precautions. Never cut or splice cords. Use an extension cord only as the manual permits. Keep connections dry and away from runoff, standing water and the washing area, and keep spray away from electrical equipment. Battery models: use only the battery and charger the maker specifies for your exact model. Emergency first: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Otherwise, complete the applicable stop and make-safe procedure before hose, nozzle, wand or accessory work, clearing a blockage, cleaning, maintenance, refueling, checking oil, adding detergent, battery changes or charging, draining, moving, transporting, storing or leaving the washer. Follow your exact manual’s procedure and order. Release the trigger and engage its lock. Gas: switch the engine off and wait for it to stop; disconnect the spark plug wire before service as the manual directs, and let hot parts cool before refueling, storage or contact. Corded: switch off and unplug by the plug with dry hands. Battery: switch off, remove a removable battery as the manual directs and keep it away while working; for a built-in battery, follow the manual’s isolation procedure and do not open the battery compartment. Complete the manual’s water-supply shutdown and pressure-relief steps: point the gun in a safe direction at a permitted discharge location, disengage the trigger lock, squeeze the trigger as directed to relieve pressure, then reengage the lock. Do not disconnect hoses or change nozzles until pressure is relieved. If pressure cannot be relieved by the prescribed procedure, obtain service without loosening fittings. Refit and inspect parts before restoring water or power. Replace a damaged high-pressure hose; never repair or patch it. Before you wash, plan how to keep wash water, detergent and debris out of streets, storm drains, ditches and streams, and check with your city or county stormwater office about collection and disposal. Send wash water to landscaping only where local rules and the detergent label permit it and the soil can absorb it without runoff or contamination. Keep children and pets away, and never let a child use the machine. Drain and store the washer as its manual directs. For exposure to a cleaning product, follow the label’s first-aid instructions and call Poison Control at 1-800-222-1222. Call 911 for a fire or immediate danger.

