A man on a riding mower towing a spreader filled with granules across a field

How Does a Tow-Behind Spreader Work? Wheel, Gears and Hitch Explained

A tow-behind spreader turns its own wheels into the power that spins a plate under the hopper, so your vehicle only pulls it. When the flow plate opens, granules drop onto the spinning plate and the plate throws them out behind you. In large-scale production, I verified seed drill calibration on weighing trays and checked sprayer nozzle output with calibration cylinders, so I always ask how a machine delivers product before I trust it. Below I follow the product from the hitch to the ground, then the checks that keep it working.

How Does a Tow-Behind Spreader Work?

A ground-driven tow-behind broadcast spreader, such as the Agri-Fab 45-0463, is a rotary spreader on wheels with no motor and no battery. The wheels turn an axle, the axle drives gears in a gearbox, and the gears spin a plate called the impeller. A flow plate in the floor of the hopper opens and closes from the driver’s seat through a control rod. Granules fall through the open flow plate onto the plate, and the spin throws them out to the sides and behind the vehicle. My guide to tow-behind spreader basics names the parts and the hitching steps in plain order.

The parts in working order, as the Agri-Fab 45-0463 manual shows them
Part What it does
Hitch tube and pin Connects the spreader to the towing vehicle with a hitch pin held by a hairpin cotter
Wheels and axle Turn as the vehicle moves and carry that turning into the gearbox
Gearbox A large gear and a small gear pass the turning to the impeller shaft
Impeller Spins under the hopper and throws the granules out
Flow plate Opens and closes the hole in the hopper floor
Control rod and arm Carry the movement from the seat to the flow plate, with an adjustable stop and a locking notch

I find it easiest to remember as a chain with one hand-operated link. The vehicle and the ground supply the motion, the gears supply the spin, and the flow plate is the only part you decide on while driving. That is why this article spends so much time on the rod and on when to open it.

The Hitch and How It Connects to Your Vehicle

The hitch is the first hands-on point, so the safety order comes before anything else. Read it once here, because every later step in this article points back to it.

Safe-State Box

Stop and make safe before you fill or unload the hopper, reach into the hopper, clear a clog, clean or rinse the spreader, lubricate it, adjust the gate or the pattern, change a part, hitch or unhitch it, move it, store it or leave it. Keep your hands, feet, hair and loose clothing away from the impeller, the plate, the agitator, the gears and the wheels while anything can turn. During normal spreading, walk or drive only as your manual and the product label permit; walking behind a push spreader, or pulling a tow-behind unit at the speed its manual describes, is operation, not transport. For a tow-behind spreader: close the gate, stop the vehicle, set the parking brake, switch the engine off and remove the key as the vehicle’s manual says, and wait until the wheels, impeller and agitator have stopped turning, before you reach into the hopper or touch the impeller. Keep the gate closed while you fill. Wear all the protective equipment the product label and your manual require while you fill, clean or clear a jam. Clear a clog only with the method in your exact manual. Follow every applicable safety step in your manual, in the order it specifies. Refit every guard and cover, and check that the gate opens and closes before product goes back in.

According to the Agri-Fab 45-0463 manual, the hitch is a hitch tube with a bracket, and a hitch pin goes through the bracket and the tube and is secured with a hairpin cotter. The manual speaks of a tractor and a towing vehicle and names no particular lawn tractor, zero-turn mower or ATV. The John Deere-branded manual of the same design says it is designed for use with lawn and garden tractors only. The vehicle’s own manual decides what it may pull. My review of the Agri-Fab 45-0463 looks at this model up close.

Towing

Follow your towing vehicle’s owner’s manual and the spreader’s own manual for hitching, turning, slopes, speed and load limits, and stay within the tow capacity in the vehicle’s owner’s manual. Never ride on a spreader or carry a passenger on it. Turn only as the two manuals direct, and keep children and pets well clear of the vehicle and the spreader while you load, hitch and spread. Before you fill, hitch, unhitch, reach into the hopper or touch the impeller, complete the tow-behind steps in the safe-state box.

What the Two Manuals Decide

Follow the exact manuals for hitch compatibility and towing limits: the vehicle’s manual sets its hitch and towing capacity, and the spreader’s manual sets the rest. The Agri-Fab manual adds that vehicle braking and stability may be affected by an attachment, and it says to stay off steep slopes and to follow the slope rules in the vehicle’s manual. It also says not to drive too close to a creek or ditch. Drainage ditches border my land, so that line matters to me. Keep the spreader well away from any ditch, as the manual directs.

From Wheel to Spinning Plate on the Ground Drive

The drive is why a tow behind broadcast spreader needs no motor. As the wheels roll, the axle turns the gears in the gearbox, and the gears turn the spreader impeller. The impeller turns only while the wheels turn, so the speed of the plate follows the speed of the vehicle.

Axle, Gears and Impeller

The Agri-Fab manual says that the position of the drive wheel and the large gear, in relation to the small gear, determines which direction the impeller spins. It tells the owner to mark the positions of the parts if the axle and gear assembly is ever taken apart, and to put them back in their original positions. Before you take the axle and gear assembly apart, complete the stop and make-safe steps for your spreader in the safe-state box above. The impeller itself slides onto the vertical spreader shaft and is held by a cotter pin. I read a gearbox diagram before I read a spec sheet, because it shows where a machine can fail and what a careless reassembly would change.

The same chain explains why the plate follows the wheels: while the vehicle rolls, the impeller turns.

What Study Data Says About Speed and the Drive

A laboratory study of a rotary turf spreader with a ground-driven impeller found that travel speed changed the application rate, and that the overlapped pattern held up better when speed went up than when it went down (1). It tested one spreader and one material, so it shows a direction and no rule for your yard. It does tell me why I treat a steady pace as part of the spreader, not as a detail. I cover what skews a broadcast pattern in a separate guide.

The Flow Plate and the Control Rod

The flow plate is the gate. It sits in the bottom of the spreader hopper and covers the opening above the impeller. A steel flow control rod runs from the plate toward the vehicle, and a control arm with a grip sits at the seat end.

According to Agri-Fab, you pull the control arm against the adjustable stop for the on position. You push it toward the hopper and then over into the locking notch for the off position. The adjustable stop sits on a wing nut, and the manual says that a higher setting number means a wider opening in the bottom of the hopper. I like a rod with a locking notch, because off is then a position the arm stays in and not a position you must hold.

The Setting Is Not Mine to Give

The product label gives the application directions, so read it before you set the gate. A setting listed for your exact spreader and product is a starting point, not proof of the amount delivered: follow the spreader’s manual and calibrate for the product, the spreader and the person using it before you apply. Never exceed the label’s application rate.

Reading the Maker’s Chart

The Agri-Fab manual has an application chart and tells the owner to use it together with the instructions on the product bag. It also says that humidity and the moisture of the material affect the chart, so small setting changes may be needed. I treat any chart the way I treated drill and sprayer settings at scale: as a starting point that a check has to confirm. A field study of commercial farm spreaders in North Carolina found that spreaders differed widely in how uniformly they spread, so a spreader’s pattern is something to check and never to assume (2). My guide to how a broadcast spreader works walks through the hopper, gate, spinner and throw.

If the gate will not close, or the control arm will not move into the locking notch, stop. Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. Never push, kick or dig product out of the gate or off the plate while anything can turn. If product clumps or bridges in the hopper or the gate clogs, stop and complete the stop and make-safe steps in the safe-state box first, then clear it only with the method in your manual.

What Happens Between the Hopper and the Ground

The hopper holds the product. Before you fill it, complete the stop and make-safe steps for your spreader in the safe-state box above, and read the product label. The manual’s first operating rule is then simple: make sure the flow plate is closed, fill the hopper and break up any lumpy product. Agri-Fab lists the 45-0463 with a 130 lb hopper. Its manual prints no fill level, and it says that a vinyl hopper cover, sold as an option, acts as a wind and moisture shield and should not be used as a rain cover.

Label First

Read the product label before you open the bag. Follow its directions for the permitted use, the application amount, protective equipment, weather, watering in, access by people and pets, storage and disposal. Using a registered pesticide in a way its label does not allow is against federal law. Follow the spreader’s manual too. If the product’s instructions and the spreader’s instructions cannot both be followed, do not use that combination; ask the manufacturers for guidance.

Protective Equipment

Wear all the protective equipment the product label and your spreader’s manual require, and put it on before you open the bag. Wear it every time you fill the hopper, clean the spreader or clear a clog. Protective equipment lowers your exposure; it does not make handling a lawn product safe. The Agri-Fab manual adds eye and hand protection for lawn or garden chemicals and substantial footwear.

Filling

Before you fill or unload the hopper, complete the stop and make-safe steps for your spreader in the safe-state box, and keep the gate closed. For fertilizer, fill on a hard surface where spilled granules can be swept up, away from drains and water. Follow the product label’s handling and ventilation directions, and wear all the protective equipment the label and your manual require. Fill only to the level your manual allows, and secure the hopper cover or lid if your spreader has one. Keep children and pets away, and never leave a filled spreader where they can reach it.

Where the Granules Go

The impeller throws the granules in a fan behind the spreader, and the maker prints a spread width for each material in its chart, up to 12 ft for the widest. That is the maker’s printed maximum for its own product; the real pattern and the spacing between passes need calibration for your product, your spreader and your pace. The manual says each pass should slightly overlap the previous one, and it says that when you broadcast weed control products the pattern must not hit evergreen trees, flowers or shrubs. My guide to spread width and pass spacing explains how swath and overlap fit together.

Spills, Runoff and Water

Keep people and pets away from a spill. Follow the product label and its safety data sheet for collecting, reusing and disposing of spilled product, and wear the protective equipment they require. Never hose or wash granules into a street, a gutter, a drain, a ditch or water, and do not pile spilled product onto the lawn or return contaminated material to the bag. If you cannot manage the spill safely, stay away and call the emergency number on the label. Call Poison Control at 1-800-222-1222 if anyone is exposed, and call 911 for a fire or immediate danger.

Keep Granules off Hard Surfaces

Keep fertilizer off pavement and out of drains and surface water. If scattered plain fertilizer lands on a sidewalk, a driveway or a patio, sweep it back onto the lawn before you water, without going over the label rate; collect a concentrated spill instead. For pesticide granules, follow the label’s cleanup instructions. Follow any buffer requirement that applies and keep fertilizer out of those areas. EPA advises against fertilizing before windy or rainy days, and Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Follow the product’s weather and watering directions too.

Why Speed and Turns Change What the Spreader Does

Because the plate follows the wheels, anything that changes how the wheels turn changes the throw. That includes the pace of the vehicle and every turn.

Gate at Stops and Turns

Close the gate before you stop, before you slow down to turn, and whenever you pause, and open it again only after you are walking or driving at the steady pace your manual describes. Do not spread while you turn.

The Agri-Fab manual says to always start the tractor in motion before opening the flow plate and to always close the flow plate before turning or stopping the tractor. It says to begin in low gear at low engine speed and to raise the speed gradually. It prints a maximum towing speed of 6 mph for this model and warns that higher speeds may cause excessive wear of the spreader gears. NC State Extension gives the same pattern for ground-driven rotary units: make turns with the spreader closed, because the pattern would be irregular while turning.

What changes the throw of a ground-driven spreader
Change What the maker or the research says
Vehicle speed The Agri-Fab manual says a change in speed requires an adjustment of the flow rate; a laboratory study found the rate changed with speed
Turning with the gate open NC State Extension says the pattern is irregular while turning, so turn with the spreader closed
Humid air or damp product The Agri-Fab manual says humidity and moisture affect the chart; a laboratory study found humid air can shift a rotary pattern
A spreader that is not level A study of tractor-mounted rotary spreaders found side-to-side tilt changed the pattern

The tilt finding comes from a test of tractor-mounted rotary spreaders, and its authors say pattern checks belong on a level spreader (3). I recommend checking that the hopper sits level on its frame before the first fill, and reading the vehicle’s manual before you drive onto any slope. I like a maker that prints a hard speed limit for the gears, because a figure I can check beats a feel for it. If your ground is rough or sloped, my spreaders for uneven ground roundup compares nine push, tow and hand models.

Checks That Keep the Drive Working

The drive is simple, so the care is simple too. Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. Then work through the manual’s list.

  • Fasteners: the manual says to make a thorough visual check for loose bolts and nuts before each use.
  • Wear: it says to check for worn or damaged parts before each use and to repair or replace them.
  • Tires: it says to check that the tires are adequately inflated before each use and never to inflate them beyond the maximum pressure printed on the tire.
  • Gearbox: it says to remove the three clips, separate the gearbox housings, apply automotive grease to the gears as needed, oil the top of the gearbox and the vertical shaft, then close the housings and secure the clips.
  • Wheel and axle: it says to oil the idler wheel and the axle bushings at least once a year or more often as needed.

Cleaning

Before you clean the spreader, complete the stop and make-safe steps in the safe-state box, and wear the protective equipment the product label and your manual require. Handle leftover product, cleaning water and residues as the product label directs. Clean the spreader only by a method both the label and the manual permit, and rinse it only where they permit it, keeping product and contaminated wash water out of drains and water supplies. Dry the spreader completely, and lubricate it as its manual directs. If you change products, follow both products’ cleaning requirements: a rinse alone does not show that all residue is gone.

Cleaning matters for the plate as much as for rust. A laboratory study found that fertilizer with insoluble parts builds up on the impeller and gradually shifts a rotary pattern (4). NC State Extension says to wash the spreader after each day’s use to avoid buildup around ports and on the impeller, to dry it completely and to keep material dry to prevent caking and clogging of the ports.

Storage

Before you store the spreader, complete the stop and make-safe steps in the safe-state box. Store it empty, clean and dry, as your manual describes, with the gate closed. Keep products in their original labeled containers, securely closed, under the storage conditions their labels give, and away from children and pets. Lock pesticides away, apart from fertilizer, food and animal feed, and never put any product into a food or drink container.

University of New Hampshire Extension and Nebraska Extension both say that fertilizer left in a spreader absorbs water and the spreader rusts. That is the reason I advise emptying the hopper at the end of a job and keeping the bag of product dry and closed.

When a Tow-Behind Spreader Fits the Job

A pull behind spreader earns its place where a push spreader would take hours, such as a large lawn or open ground with long runs. On my 3.7-acre orchard, the alleys between the tree rows carry cover crop, and that is the kind of long, open run where I picture a wheeled hopper behind a vehicle in place of a hand spreader. A push spreader still wins on a small lawn and around edges, so I treat the two forms as complementary options in my comparison of push versus tow-behind spreaders.

Three things are worth carrying away: the wheels drive the plate, the flow plate is your off switch, and the manuals of the vehicle and the spreader set every limit that matters. My tip is to open the maker’s manual at the gearbox page before the first hitch, and to read the vehicle’s manual in the same sitting. If anyone is exposed to a lawn product, follow the first-aid section of the product label and call Poison Control at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.

My advice for anyone choosing a wheel-driven spreader to pull behind a vehicle is to learn the drive and the gate before the first load goes in. For a long lawn, my spreaders for a large lawn roundup compares seven push and tow-behind picks.

Frequently Asked Questions

How does the wheel turn the plate on a tow-behind spreader?

The wheel turns the plate on a tow-behind spreader through an axle and a pair of gears. According to Agri-Fab, the position of the drive wheel and the large gear in relation to the small gear sets which direction the impeller spins. The impeller itself sits on a vertical shaft under the hopper.

Does a tow-behind spreader spread when the vehicle is stopped?

A tow-behind spreader with a ground-driven plate turns its impeller only while its wheels turn, so a stopped vehicle means a stopped drive. The flow plate is a separate control, and the Agri-Fab 45-0463 manual says to close it before turning or stopping. Your vehicle’s manual and the spreader’s manual decide the rest.

Should you open a tow-behind spreader before or after the vehicle starts moving?

Open a tow-behind spreader only after the vehicle is moving. The Agri-Fab 45-0463 manual says to always start the tractor in motion before opening the flow plate and to close it before turning or stopping. The vehicle’s manual and the spreader’s manual decide the pace.

What does the flow control rod do on a tow-behind spreader?

The flow control rod carries the movement of the control arm at the seat to the flow plate in the bottom of the hopper. According to Agri-Fab, the arm against the adjustable stop is on, and the arm pushed toward the hopper and over into the locking notch is off. The stop sets how wide the opening is, and the chart and the product label decide where it goes.

How do you turn with a tow-behind spreader?

Close the flow plate before you turn, and turn only as the vehicle’s manual and the spreader’s manual direct. NC State Extension says to make turns with a ground-driven rotary spreader closed, because the pattern would be irregular while turning. Keep children and pets well clear of the vehicle and the spreader.

References

  1. Parish RL. The effect of speed on performance of a rotary spreader for turf. Appl Eng Agric. 1987;3(1):17-19.
  2. Crozier CR, Roberson GT. Granular fertilizer spreader swath uniformity achieved at varying target application rates. Crop Manag. 2014;13(1):1-6.
  3. Yildirim Y. Effect of side to side spreader angle on pattern uniformity in single- and twin-disc rotary fertilizer spreaders. Appl Eng Agric. 2008;24(2):173-179.
  4. Parish RL. The effect of relative humidity on rotary turf spreader patterns. Appl Eng Agric. 1991;7(5):541-544.

Safety Note: Read the product label and your spreader’s manual before handling product. Follow both; if their instructions cannot both be met, do not use that combination. Registered pesticide use must comply with its labeling. A listed spreader setting is a starting point; calibrate as the manual directs and never exceed the label rate. Wear all protective equipment required by the label and manual before opening the container and during filling, cleanup and jam clearing. Wash your hands before eating, drinking, smoking or using the restroom when working with pesticides. After application, change your clothes and wash your hands immediately, and follow the label’s additional washing and clothing instructions. Keep children, pets and other people away during handling and application and off treated areas for as long as the label requires. Emergency first: if a battery becomes unusually hot, swells, hisses, smells unusual or smokes, stop using the spreader without handling or removing the battery. Keep people away and follow the battery manual’s emergency instructions. If it smokes, burns or presents immediate danger, move away and call 911 or the fire department. Otherwise, complete the applicable stop and make-safe sequence before filling, unloading, reaching into the hopper, clearing a jam, cleaning, lubricating, adjusting, changing parts or batteries, hitching, unhitching, transporting, storing or leaving the spreader. Walk-behind or hand-crank: close the gate, stop walking or cranking, and wait for all moving parts to stop. Tow-behind: close the gate, stop the vehicle, set the parking brake, switch off the engine and remove the key as the vehicle manual directs, and wait for the wheels, impeller and agitator to stop before reaching into the hopper or touching the impeller. Battery spreader: release the trigger or close the gate, switch off, wait for moving parts to stop, then remove the battery as the manual directs and keep it away while working. Follow any additional isolation steps in the exact manual. Keep hands, feet, hair and loose clothing away from moving parts. Clear jams only by the manual’s method. Refit guards and covers and check the gate before refilling. With the spreader made safe and the gate closed, fill fertilizer on a hard surface where spills can be collected, away from drains and water. Follow the label’s handling and ventilation directions and the manual’s fill limit. Keep people and pets away from spills. Follow the label and safety data sheet for collection, reuse and disposal; do not spread concentrated spills onto the lawn or return contaminated product to its bag. Sweep scattered plain fertilizer from pavement onto the intended lawn before watering only without exceeding the label rate. Follow the label’s cleanup instructions for pesticide granules. Never wash product into streets, gutters, drains, ditches or water. Observe applicable buffers. EPA advises against fertilizing before windy or rainy days; Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Close the gate before stopping or turning, as the manual directs. Follow both towing manuals for hitching, turning, slopes, speed and load limits; never ride on the spreader or carry passengers on it. Use only batteries specified for the model. Recharge rechargeable batteries only with a charger approved for them, as the manual directs; never recharge disposable cells. After completing the applicable shutdown, handle leftover product, cleaning water and residues according to the product label. Clean only by methods permitted by both label and manual, keeping contaminated water out of drains and water supplies. Rinse only if permitted, then dry and lubricate as directed. A rinse does not establish that all pesticide residue is gone. Use salt or ice melt only when the product directions and spreader manual permit it. Salt-based deicers can damage metal; follow the model’s cleaning instructions. Do not use lawn fertilizer to melt ice. Store the spreader empty, clean and dry as its manual directs. Keep products securely closed in their original labeled containers under their labels’ storage conditions, away from children and pets. Lock pesticides away, separate from fertilizer, food and feed; never use food or drink containers. For human exposure, follow the label’s first-aid instructions, call Poison Control at 1-800-222-1222 and keep the label available. Call 911 for immediate danger.

Scroll to Top