The Scotts vs Brinly spreader choice comes down to the hopper, the wheels and the handle controls: pick the Brinly P20-500BHDF-A if you want a 50 lb hopper, pneumatic wheels and a side deflector in the box, and pick the Scotts DLX if you want the mid-range tier with a gate trigger on the handle and a lever for the right side. In large-scale production, I verified seed drill calibration on weighing trays, so I compare printed facts row by row before I trust a spreader. Below, both walk-behind broadcast spreaders sit side by side on hopper, gate, side control, wheels, setup, safety and warranty.
Affiliate Disclosure: Garden Power Scout is a proud participant in the Amazon Services LLC Associates Program. As an Amazon Associate, we earn from qualifying purchases, at no extra cost to you.
Scotts vs Brinly Spreader: The Short Answer
Brinly P20-500BHDF-A 50 lb Push Spreader With Deflector is my pick for most buyers, because it brings a 50 lb hopper, 12 in x 3 in pneumatic wheels and a left-side deflector in the box. Scotts Turf Builder EdgeGuard DLX Broadcast Spreader is my pick when you want the mid-range tier and a gate trigger on the handle. Neither has a motor: both are push spreaders that you walk behind, so the decision follows the rows below and the edges of your lawn. Walk-behind models like these are ranked by frame and wheels in my push spreader roundup.
| Row | Scotts EdgeGuard DLX | Brinly P20-500BHDF-A |
|---|---|---|
| Spreader type | Broadcast (rotary) push spreader | Broadcast (rotary) push spreader |
| Price tier | Mid-range | Premium |
| Hopper capacity | Pounds: Not listed. Rated by the maker for up to 15,000 sq. ft. of its own lawn products | 50 lb, the maximum load in the manual |
| Spread width, maker’s ceiling | Not listed | Up to 12 ft (8 to 12 ft as the maker prints it) |
| Gate and rate control | Trigger on the handle; numbered Precision Rate Dial on the back of the hopper | Flow control lever on a numbered plate; rod linkage to a shut-off plate under the hopper |
| Hopper parts | Agitator inside the hopper (maker’s diagram label) | Removable rotary agitator, hopper screen |
| Side control | EdgeGuard lever, blocks the right side | Deflector kit in the box, mounts on the left side |
| Wheels | Open-spoke, type and size Not listed | Pneumatic, 12 in x 3 in |
| Power source | None (push) | None (push) |
| Weight | Not listed | Not listed |
| In the box | Spreader; top half of the handle raised and fixed with wing nuts | Hopper, frame, wheels, gearbox, impeller, shut-off plate, hopper screen, agitator, deflector kit |
| Warranty, household use | Not listed | Manual edition 1008066-F: 2 years for steel frame and hopper, 90 days for tires, wheels and gears |
The hopper and the wheels decide it for most buyers. The Brinly has a 50 lb hopper and 12 in x 3 in pneumatic wheels. The DLX answers with open-spoke wheels, a lower tier and a trigger you squeeze at the handle, which is the whole case for it.
Safety Before You Fill, Adjust or Clean
Every hands-on step with a push spreader starts the same way: make the machine safe before a hand goes near the hopper, the gate or the plate. Both spreaders here are walk-behind models, so the box below gives the walk-behind order. Read it before you fill, clear a clog, clean, adjust the gate or move the spreader.
Stop and Make Safe First
Stop and make safe before you fill or unload the hopper, reach into the hopper, clear a clog, clean or rinse the spreader, lubricate it, adjust the gate or the pattern, change a part, move it, store it or leave it. Keep your hands, feet, hair and loose clothing away from the impeller, the plate, the agitator, the gears and the wheels while anything can turn. During normal spreading, walk only as your manual and the product label permit; walking behind a push spreader is operation, not transport. Walk-behind or hand-crank spreader: close the gate, then stop walking or cranking, and wait until the impeller, plate, agitator and wheels have stopped turning. Keep the gate closed while you fill. Wear all the protective equipment the product label and your manual require while you fill, clean or clear a jam. Clear a clog only with the method in your exact manual. Follow every applicable safety step in your manual, in the order it specifies. Refit every guard and cover, and check that the gate opens and closes before product goes back in.
Read the Label and the Manual First
Read the product label before you open the bag. Follow its directions for the permitted use, the application amount, protective equipment, weather, watering in, access by people and pets, storage and disposal. Using a registered pesticide in a way its label does not allow is against federal law. Follow the spreader’s manual too. If the product’s instructions and the spreader’s instructions cannot both be followed, do not use that combination; ask the manufacturers for guidance.
Wear all the protective equipment the product label and your spreader’s manual require, and put it on before you open the bag. Wear it every time you fill the hopper, clean the spreader or clear a clog. Protective equipment lowers your exposure; it does not make handling a lawn product safe. Brinly’s manual adds eye protection, substantial footwear and long trousers, no open sandals and no loose clothing that can catch in moving parts, and it says not to let children or an untrained person operate the machine.
Wash your hands before eating, drinking, smoking or using the restroom when you work with pesticides. Change your clothes and wash your hands immediately after you apply a product that contains a pesticide, and follow the label’s additional washing and clothing instructions.
Brinly’s manual adds that you should wash your hands after contact with fertilizers and pesticides, that smoking, drinking and eating are off limits around chemicals, and that nobody may sit or ride on the equipment while it is in use.
The product label gives the application directions, so read it before you set the gate. A setting listed for your exact spreader and product is a starting point, not proof of the amount delivered: follow the spreader’s manual and calibrate for the product, the spreader and the person using it before you apply. Never exceed the label’s application rate.
Filling, Spills and Clogs
Before you fill or unload the hopper, complete the stop and make-safe steps for your spreader in the safe-state box, and keep the gate closed. For fertilizer, fill on a hard surface where spilled granules can be swept up, away from drains and water. Follow the product label’s handling and ventilation directions, and wear all the protective equipment the label and your manual require.
Fill only to the level your manual allows, and secure the hopper cover or lid if your spreader has one. Keep children and pets away, and never leave a filled spreader where they can reach it. Brinly’s manual says to fill on a flat, level surface such as a sidewalk, a driveway or cardboard, never to load more than 50 lb, and to use the screen when filling. Scotts says to fill over the driveway and to clean up any product that spills.
Keep people and pets away from a spill. Follow the product label and its safety data sheet for collecting, reusing and disposing of spilled product, and wear the protective equipment they require. Never hose or wash granules into a street, a gutter, a drain, a ditch or water, and do not pile spilled product onto the lawn or return contaminated material to the bag. If you cannot manage the spill safely, stay away and call the emergency number on the label. Call Poison Control at 1-800-222-1222 if anyone is exposed, and call 911 for a fire or immediate danger.
Keep children, pets and other people away from the area while you fill and spread, and keep them off the treated area for as long as the label says. Store the bag and the filled spreader where they cannot reach them.
Never push, kick or dig product out of the gate or off the plate while anything can turn. If product clumps or bridges in the hopper or the gate clogs, stop and complete the stop and make-safe steps in the safe-state box first, then clear it only with the method in your manual.
If someone swallows or is exposed to a lawn product, follow the first-aid section of the product label and call Poison Control (America’s Poison Centers) at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.
Hopper, Gate and Rate Control
The gate decides when product leaves the hopper, so it is the control I look at first on any push spreader. Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. The product’s bag and the maker’s chart give the starting setting, and your own check settles it.
Scotts EdgeGuard DLX Gate and Hopper
The Scotts Turf Builder EdgeGuard DLX Broadcast Spreader has a trigger on the handle. According to Scotts, you squeeze the trigger to release the product and release it when you make turns. The numbered Precision Rate Dial sits on the back of the hopper, and the guide says to set it from the setting on the product’s package. Scotts labels a rustproof hopper with an agitator inside it. My EdgeGuard DLX review covers the handle, trigger, edge control and fit in full.
With the hopper empty, I squeeze the trigger and watch the gate open, then let go and watch it close, before any product goes in. The rate dial sits on the back of the hopper, facing me as I walk behind it, so I read it before I start with the gate closed. When I look into the open hopper, the agitator is the first thing I check for, because Scotts labels it there.
Brinly P20-500BHDF-A Gate and Hopper
The Brinly P20-500BHDF push spreader, sold as the P20-500BHDF-A, uses a flow control lever on a numbered plate with a rod linkage to a shut-off plate under the hopper. The manual’s set-up steps are specific: push the flow control handle down to the fully closed position and close the shut-off plate, hand-tighten the linkage nuts, then move the handle up and down to verify that the plate opens and closes. It adds that only the lower nut takes a wrench. My Brinly spreader review goes through the P20 and its side deflector in full.
This is the part of the Brinly I slow down for, so I follow those steps in the manual’s order and watch the plate move with the hopper empty. The 50 lb hopper takes a screen that Brinly says to use when filling, and a removable rotary agitator that the manual says to use only if needed. Brinly says that published flow control settings are approximate only, so the bag and your own check decide the setting.
Winner: the Brinly P20-500BHDF-A, because its manual sets out the gate set-up and a check that the shut-off plate opens and closes, while the DLX gives you a trigger to squeeze and a dial to read.
Side Control: EdgeGuard Lever vs Side Deflector
Both spreaders carry a maker’s feature for one side of the throw, and they sit on opposite sides. According to Scotts, the EdgeGuard lever on the Scotts EdgeGuard DLX, slid to On, blocks off the right side of the spreader pattern to prevent product from spreading onto non-lawn areas. Brinly’s manual says the deflector on the P20-500BHDF-A will keep material from moving toward the left side of the hopper. Those are each maker’s description of its own feature.
Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. On the DLX, the lever slides at the hopper, and I slide it to On and back with the hopper empty to see how far it travels. On the Brinly, the deflector is a flip-up shield: you loosen the knob and rotate it up or down, as the manual says, and fitting it means tipping the spreader onto its right side to remove two screws from the left side of the hopper frame.

How well either feature keeps product off a bed or a path is for you to judge on your own lawn, because neither maker states a result. The same manual covers the Brinly P20-500BH push spreader without the deflector, so check the model name before you order parts. I rank push models by edge control and kit in my fertilizer spreader roundup.
Keeping Granules Off Pavement and Out of Water
Where granules land matters as much as how the pattern looks. Purdue Extension says fertilizer that lands on a driveway or another hard surface and is not swept or blown back onto the turf can run off into surface waters (1).
Keep fertilizer off pavement and out of drains and surface water. If scattered plain fertilizer lands on a sidewalk, a driveway or a patio, sweep it back onto the lawn before you water, without going over the label rate; collect a concentrated spill instead. For pesticide granules, follow the label’s cleanup instructions. Follow any buffer requirement that applies and keep fertilizer out of those areas. EPA advises against fertilizing before windy or rainy days, and Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Follow the product’s weather and watering directions too.
Drainage ditches border my land, which is why the buffer line is the one I read twice. Purdue gives about 10 feet of vegetative buffer around ponds, lakes and streams, a figure that varies by state and ordinance, so the label and local rules decide.
Winner: neither, because each maker only states which side its feature covers, and the result is yours to check.
Wheels, Handle and Frame
The wheels and the handle decide how the spreader feels from the first step, and this is where the two makers print the least in common. The DLX has two open-spoke wheels with an orange hub cap and a tall black U-shaped handle whose top half you raise and fix with wing nuts. The Brinly has 12 in x 3 in pneumatic wheels, and its manual lets you lower the handle assembly by moving it to the upper bolt holes.
I roll each spreader empty along the concrete pad before it meets a lawn. On the Brinly, the printed maximum tire pressure is the first number I look for on the tire, because the manual says the pressure should not be reduced below 70 percent of that maximum. For the DLX, I look at the open spokes and the hub cap and leave durability out, because no maker figure says how long they last.

According to Brinly, the hopper is poly and described as rust-proof, and the frame is powder-coated. Brinly’s manual also says to keep nuts, bolts and screws tight, and to sand and paint frame rust with enamel. Scotts labels the DLX hopper rustproof in its guide and prints no frame material.
Winner: the Brinly P20-500BHDF-A, because of its 12 in x 3 in pneumatic wheels and a handle you can lower.
Turns, Pace and Keeping It Level
A push broadcast spreader throws product from a plate that the wheel turns, so how you walk and turn changes what the plate does. Both makers say the same thing about turns. Scotts says to release the trigger when making turns and not to leave the spreader open, and Brinly says to start and stop the spread while moving and not to open the lever while stopped, or material runs onto the ground without being spread. I compare push, tow-behind and handheld models in my broadcast spreader roundup.
Close the gate before you stop, before you slow down to turn, and whenever you pause, and open it again only after you are walking or driving at the steady pace your manual describes. Do not spread while you turn.
Pace matters because it changes the rate. A laboratory test of one rotary spreader and one material found that the application rate changed with modest changes in speed, so keep the pace you used when you checked the spreader (2). A second laboratory study found that humid air can change how a fertilizer behaves on the plate, and that material with insoluble parts builds up on the impeller and gradually shifts the pattern (3). Brinly says the same about build-up: excess material on the spinner blade can cause an uneven pattern.
A test of tractor-mounted rotary spreaders tilted from side to side found that the angle changed the pattern (4). That was farm equipment, so I take only the principle: Brinly’s manual says to keep the impeller level, and I keep either push spreader level too. A field study of commercial farm spreaders found wide differences in how evenly they spread, which is why I check a spreader before I trust it (5). I sort push, tow and hand models by how they cope with rough ground in my roundup of spreaders for uneven ground.
Brinly’s manual also says not to use the spreader on windy days. NC State Extension says wind speed and direction, slope, temperature and humidity affect distribution, and that when conditions interfere it is a good idea to delay application. The bag’s label and the maker’s chart decide the setting. My first strip of any job is a check I look at before I go on.
Setup, First Check and Cleaning
Setup is where the two spreaders differ most in effort, and a Brinly push spreader asks for more of it. Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. The DLX needs one step, and the Brinly needs a short sequence of bolts, linkage and a check of the shut-off plate.
Scotts says to raise the top half of the handle to the upright position and tighten the wing nuts by hand, with no tool named. Brinly’s manual lists two 10 mm wrenches, a pivot and bracket to remove and refit, the control rod to insert into the flow control handle and the nuts and bolts to tighten on both sides, with the deflector last. I leave the first run of any new spreader to the manual’s own test: practice walking with it, opening and closing the rate gate at the right moments, before any product goes into the hopper.
Cleaning After Each Use
Before you clean the spreader, complete the stop and make-safe steps in the safe-state box, and wear the protective equipment the product label and your manual require. Handle leftover product, cleaning water and residues as the product label directs. Clean the spreader only by a method both the label and the manual permit, and rinse it only where they permit it, keeping product and contaminated wash water out of drains and water supplies. Dry the spreader completely, and lubricate it as its manual directs. If you change products, follow both products’ cleaning requirements: a rinse alone does not show that all residue is gone.
Scotts says never to leave product in the spreader and to pour leftover material back into the package and seal it tightly. Brinly’s manual says to clean and oil the spreader immediately after each use, to move the flow control handle while you rinse, and never to let material sit in the hopper for long periods. The one troubleshooting line in the Brinly manual is a stiff flow control handle: check for build-up between the bottom of the hopper and the shut-off plate, and clean as needed, after the stop and make-safe steps.
When I clean the Brinly, I watch where product collects around the shut-off plate, because the manual points there. On the DLX, I look at how the hopper empties and where granules stay on the plate and in the corners, because Scotts says to pour the rest back into the package.
Storing the Spreader
Before you store the spreader, complete the stop and make-safe steps in the safe-state box. Store it empty, clean and dry, as your manual describes, with the gate closed. Keep products in their original labeled containers, securely closed, under the storage conditions their labels give, and away from children and pets. Lock pesticides away, apart from fertilizer, food and animal feed, and never put any product into a food or drink container.
Brinly’s manual says fertilizer left in the hopper can draw moisture, form clumps and cause rusting or jamming of controls, and Scotts says to let the spreader dry thoroughly and store it in a clean, dry place.
Ice Melt and Corrosion
Use ice melt or salt only when both the product’s directions and your spreader’s manual permit it. Salt-based deicers can damage metal, so follow your model’s cleaning instructions after use. Before you clean the spreader, complete the stop and make-safe steps in the safe-state box. Rinse only if the manual permits it, and dry the spreader as the manual directs. Do not use lawn fertilizer to melt ice. Keep deicing products away from children and pets.
Brinly’s manual allows ice melt only with the screen removed, says to clean the spreader thoroughly afterward because ice melt can be highly corrosive, and says to put the screen back when you are done. For the DLX, Scotts’ own graphic says it is not recommended for rock salt use, so keep rock salt out of it and follow what Scotts prints for your edition before you put any ice melt in it.
Warranty and Documents
The Brinly push broadcast spreader comes with a manual, edition 1008066-F, that gives household terms for the P20-500BHDF-A: 2 years for the steel frame and the hopper, and 90 days for tires, wheels and drive gears. It excludes commercial and rental use. Scotts gives no term for the DLX in its Quick Start Guide, which carries a 2011 copyright, so ask Scotts for the current warranty and read the newest guide before you buy.
Winner: neither, because one has short parts terms and the other lists none.
Choose the Scotts EdgeGuard DLX If
Choose the Scotts Turf Builder EdgeGuard DLX Broadcast Spreader when the tier and the handle controls matter more to you than the Brinly’s hopper and wheels.
- You want the mid-range tier. The DLX sits a tier below the Brinly.
- You want a trigger on the handle. Scotts describes a trigger that you squeeze to release product and let go of for turns.
- Your edge to protect is on the right. The EdgeGuard lever blocks the right side of the pattern, according to Scotts.
I picture the Scotts EdgeGuard DLX spreader on the open ground beside the house lawn, where a lever that I slide to On before I walk the edge earns its place. My Scotts and EarthWay spreaders comparison pits the same DLX against the EarthWay 2600A-Plus.

Choose the Brinly P20-500BHDF-A If
Choose the Brinly P20-500BHDF-A 50 lb Push Spreader With Deflector when you want a 50 lb hopper, pneumatic wheels and the deflector in the box.
- You want a 50 lb hopper. The manual caps the load at 50 lb. I sort push and tow-behind models by hopper size in my roundup of spreaders for a large lawn.
- You want pneumatic wheels. They measure 12 in x 3 in.
- Your edge to protect is on the left. The deflector mounts on the left side of the hopper, according to Brinly’s manual. EarthWay closes the same left side with a lever, which I compare with the P20 in my Brinly and EarthWay spreaders comparison.
The gate check on the Brinly, with the hopper empty and the plate opening and closing in front of me, is the step that makes me trust the linkage before I fill it.

Picking Between the Two Spreaders
Three points carry the decision. The Brinly brings a 50 lb hopper, pneumatic wheels and a deflector in the box, the DLX gives a handle trigger and a right-side lever at a lower tier, and neither spreads right until you check it for your product and for the way you walk. Read the product label first, because it decides what either hopper may hold. For most buyers, the Scotts vs Brinly spreader decision lands on the Brinly P20-500BHDF-A, and for a mid-range budget with a handle trigger it lands on the Scotts DLX. For more models, my lawn spreader picks compare push and handheld spreaders on hopper and gate.
Frequently Asked Questions
What is the difference between the Scotts EdgeGuard DLX and the Brinly P20-500BHDF-A spreader?
The main difference between the Scotts EdgeGuard DLX and the Brinly P20-500BHDF-A spreader is the hardware: the Brinly has a 50 lb hopper, 12 in x 3 in pneumatic wheels and a deflector in the box. The DLX has a handle trigger and a right-side EdgeGuard lever, and it sits a tier lower.
Which side does the deflector block on the Brinly P20-500BHDF-A and the Scotts EdgeGuard DLX?
The Brinly P20-500BHDF-A deflector covers the left side, and the Scotts EdgeGuard DLX lever covers the right side. Brinly’s manual says its deflector keeps material from moving toward the left side of the hopper, and Scotts says its lever, set to On, blocks off the right side of the pattern.
Do the Scotts EdgeGuard DLX and the Brinly P20 have pneumatic wheels?
Brinly prints pneumatic wheels, 12 in x 3 in, for the P20-500BHDF-A, and Scotts prints no wheel type for the EdgeGuard DLX. The DLX is shown with open-spoke wheels with an orange hub, so check the wheel type with Scotts before you order, and follow Brinly’s maximum tire pressure on the tire.
Which of the two spreaders has a trigger on the handle for the gate?
The Scotts EdgeGuard DLX has the trigger on the handle for the gate: Scotts says to squeeze it to release the product and to release it when you make turns. The Brinly P20-500BHDF-A uses a flow control lever that you push down toward the hopper to close the rate gate.
Does the Scotts EdgeGuard DLX have an agitator in the hopper?
The Scotts EdgeGuard DLX has an agitator in the hopper, which Scotts labels on the diagram of its Quick Start Guide. The Brinly P20-500BHDF-A has a removable rotary agitator that its manual says to use only if needed, so check which one your model carries before you rely on it.
References
- Bigelow CA, Tudor WT, Nemitz JR. Facts About Phosphorus and Lawns. AY-334. Purdue University Extension.
- Parish RL. The effect of speed on performance of a rotary spreader for turf. Appl Eng Agric. 1987;3(1):17-19.
- Parish RL. The effect of relative humidity on rotary turf spreader patterns. Appl Eng Agric. 1991;7(5):541-544.
- Yildirim Y. Effect of side to side spreader angle on pattern uniformity in single- and twin-disc rotary fertilizer spreaders. Appl Eng Agric. 2008;24(2):173-179.
- Crozier CR, Roberson GT. Granular fertilizer spreader swath uniformity achieved at varying target application rates. Crop Manag. 2014;13(1):1-6.
Safety Note: Read the product label and your spreader’s manual before handling product. Follow both; if their instructions cannot both be met, do not use that combination. Registered pesticide use must comply with its labeling. A listed spreader setting is a starting point; calibrate as the manual directs and never exceed the label rate. Wear all protective equipment required by the label and manual before opening the container and during filling, cleanup and jam clearing. Wash your hands before eating, drinking, smoking or using the restroom when working with pesticides. After application, change your clothes and wash your hands immediately, and follow the label’s additional washing and clothing instructions. Keep children, pets and other people away during handling and application and off treated areas for as long as the label requires. Emergency first: if a battery becomes unusually hot, swells, hisses, smells unusual or smokes, stop using the spreader without handling or removing the battery. Keep people away and follow the battery manual’s emergency instructions. If it smokes, burns or presents immediate danger, move away and call 911 or the fire department. Otherwise, complete the applicable stop and make-safe sequence before filling, unloading, reaching into the hopper, clearing a jam, cleaning, lubricating, adjusting, changing parts or batteries, hitching, unhitching, transporting, storing or leaving the spreader. Walk-behind or hand-crank: close the gate, stop walking or cranking, and wait for all moving parts to stop. Tow-behind: close the gate, stop the vehicle, set the parking brake, switch off the engine and remove the key as the vehicle manual directs, and wait for the wheels, impeller and agitator to stop before reaching into the hopper or touching the impeller. Battery spreader: release the trigger or close the gate, switch off, wait for moving parts to stop, then remove the battery as the manual directs and keep it away while working. Follow any additional isolation steps in the exact manual. Keep hands, feet, hair and loose clothing away from moving parts. Clear jams only by the manual’s method. Refit guards and covers and check the gate before refilling. With the spreader made safe and the gate closed, fill fertilizer on a hard surface where spills can be collected, away from drains and water. Follow the label’s handling and ventilation directions and the manual’s fill limit. Keep people and pets away from spills. Follow the label and safety data sheet for collection, reuse and disposal; do not spread concentrated spills onto the lawn or return contaminated product to its bag. Sweep scattered plain fertilizer from pavement onto the intended lawn before watering only without exceeding the label rate. Follow the label’s cleanup instructions for pesticide granules. Never wash product into streets, gutters, drains, ditches or water. Observe applicable buffers. EPA advises against fertilizing before windy or rainy days; Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Close the gate before stopping or turning, as the manual directs. Follow both towing manuals for hitching, turning, slopes, speed and load limits; never ride on the spreader or carry passengers on it. Use only batteries specified for the model. Recharge rechargeable batteries only with a charger approved for them, as the manual directs; never recharge disposable cells. After completing the applicable shutdown, handle leftover product, cleaning water and residues according to the product label. Clean only by methods permitted by both label and manual, keeping contaminated water out of drains and water supplies. Rinse only if permitted, then dry and lubricate as directed. A rinse does not establish that all pesticide residue is gone. Use salt or ice melt only when the product directions and spreader manual permit it. Salt-based deicers can damage metal; follow the model’s cleaning instructions. Do not use lawn fertilizer to melt ice. Store the spreader empty, clean and dry as its manual directs. Keep products securely closed in their original labeled containers under their labels’ storage conditions, away from children and pets. Lock pesticides away, separate from fertilizer, food and feed; never use food or drink containers. For human exposure, follow the label’s first-aid instructions, call Poison Control at 1-800-222-1222 and keep the label available. Call 911 for immediate danger.


