A man comparing an earth auger to a shovel for digging holes in a backyard

Earth Auger vs Shovel: Which Digs Better for Your Yard Project

Earth auger vs shovel comes down to how many holes you dig and how much the ground around them matters. One tree, one stake or one hole beside a drip line belongs to the shovel, and a long row of same-width post holes in workable soil is where a one-person auger earns its place. Either way, the locate call comes first. I farm an apricot and plum orchard planted in 2016, so every tree on it began as a hole. Below you get the short answer, hole shape, soil, effort, safety and when each tool fits.

Earth Auger vs Shovel: The Short Answer

Use a shovel for one or two holes, for planting a tree and for any hole near roots or a marked line. Pick a one-person earth auger when you have many holes of the same width in soil the bit can bore, and leave the large, deep or hard-ground jobs to a rental machine or a professional. The number of holes and the ground around them decide it.

I settle it with three checks: how many holes there are, what lies under each spot and what goes into each hole. A tree wants a wide, sloped hole, and a post wants a straight one. The table gives my pick for the jobs I see most.

My pick by job
Job My pick Why
One tree or shrub Shovel The hole should be wide and sloped, and its walls matter to the roots.
One stake or one post Shovel A machine adds fuel or charging, safety gear and the same locate for a single hole.
A hole beside a drip line or marked line Shovel, after the locate Near marks, follow your state’s rules, and careful hand digging is part of them.
A straight row of same-width holes Earth auger or rental machine Every hole is the same width, and the powered flighting carries the loosened soil up.
Rock-hard, frozen or root-filled ground Not an auger job Echo’s manual says not to run the unit in excessively rocky ground, and a bit can bind on roots.

How an Earth Auger and a Shovel Dig

Both tools take out a column of soil, but they use different forces, and that difference explains most of what follows.

What the Machine Does

An earth auger is a power head with a steel bit that carries a helical flight, a spiral that lifts loosened soil up the shaft. The power head is a gas engine or a battery motor with a gearbox, and the bit screws into the ground. According to Echo, its sealed gear case gives a 30.2 to 1 reduction. The Ryobi, Echo and Champion manuals tell the operator to lift the bit out of the hole now and then so the soil leaves the flighting, and EGO and Makita say to work deep or clay holes in steps. I describe the parts and the common types in a separate guide on what an earth auger is.

The machine turns the bit with real torque, and a bit that binds twists the machine in your hands. Echo, Powermate, EGO and Makita all warn about it in their manuals.

What the Shovel Does

A shovel has no power head, so every load comes up on your own lift. It cuts, lifts and tells your hands what it hits. A spade tells me about a root through the handle before I see it, and no torque reaches my wrists, only the weight of each load.

Earth Auger vs Shovel for Planting Holes

For a tree or shrub I take the shovel, because the extension guides ask for a hole shape that a straight auger bore cannot make.

The Hole a Tree Wants

Colorado State Extension asks for a saucer-shaped hole three times the width of the root ball and one to two inches shallower than its height. Maryland Extension says at least twice as wide, no deeper than the root ball, with sides that slope outwards. Depth matters most: in a field trial, planting 15 or 31 centimeters below grade killed half of the Yoshino cherries within two years, while every cherry planted at grade lived (1). No tool saves you from measuring the root ball first.

What an Auger Does to the Hole Wall

British Columbia’s agriculture ministry says in its hazelnut planting guide that planting by auger tends to compact the soil at the edges of the hole and can smooth the sides, creating a barrier that young roots have trouble penetrating. The same guide calls planting by shovel the preferred method. A review of soil compaction found that compaction cuts aeration and water uptake and slows the growth of woody plants (2).

That review covers compaction in general and not auger walls, and the ministry guide is about hazelnuts. I read them together as a reason to roughen any smooth wall, and Colorado State tells planters to cut the sides of the hole with a shovel to remove glazing.

Earth Auger vs Shovel Size: Bit Diameter and Hole Depth

An auger’s hole is as wide as its bit, and the bit sizes the makers list top out near 10 inches. Ryobi lists 4, 6, 8 and 10 inch bits, Echo lists 6, 8 and 10 inch earth augers, and EGO lists bits from 100 to 250 millimeters. For the choice most buyers face first, I compare 6-inch and 8-inch auger bits side by side.

Worked Example: One Tree

Take a root ball 18 inches across and 16 inches tall, a size I picked for the sum. Colorado State’s three times rule gives a hole 54 inches wide and 14 to 15 inches deep, and Maryland’s minimum of twice the width gives 36 inches. Even the smaller figure is more than three times the widest bit on the makers’ lists, so the auger cannot make that hole and a shovel can.

Depth for Posts and Footings

Penn State Extension’s page on horse fencing gives 36 inches as a typical line post depth and about 48 inches for corner and gate posts, and it says sandy or chronically wet soil needs deeper holes. Those are horse fence figures, and frost, soil and local code can change them. Ten line posts and two corner posts at those depths come to 456 inches of hole, about 38 feet, which is the kind of job that makes a machine attractive. For a fence line like this, I also weigh the machine against a manual post hole digger by job size and soil.

A maker’s depth figure is a printed maximum for a named bit, never what you will reach in your soil. Ryobi prints 31 inches as the maximum hole depth in the specifications of its 40V cordless auger with an 8 inch bit and recommends about 24 inches in its operating instructions, both under the 36 inch line post figure, and some makers sell extensions, such as EGO’s 500 millimeter one, under their own manual. For deck footings, the city of Blaine, Minnesota asks for footings at least 42 inches below grade for frost. An auger makes the round hole, and your building department decides its depth and size. For machines used on such holes, I compare the options in my roundup of augers for deck footing holes.

Soil, Roots and Stones

Both tools lose to bad ground, in different ways.

Full Shutdown Box

Shutdown before you clear or free the bit, change or attach the bit, free a stuck bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger. Never reach toward the bit while it turns, and never clear it or free it with the machine running. Corded electric auger: release the switch or trigger, wait until the bit has stopped completely, then unplug the auger from the outlet by the plug, not the cord. Before transport or storage, also let the motor cool. Battery auger: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where your model has one, and keep it away from the auger. Gas auger: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire (a spark plug cap on some makes) and secure it away from the plug. Let the engine and muffler cool before you touch the bit or anything near the exhaust. Only then free a stuck bit or clear wrapped material, using only the method your manual specifies (gloves do not make grabbing sharp wire or cutting edges safe), and check the bit and guards for damage. Do not handle unidentified wire, cables or pipes. Do not use reverse or run the engine or motor to back the bit out unless your manual expressly authorizes it for this task, with both hands on the designated handles and everyone clear of the bit; complete the full shutdown again before any further hands-on work. Add every step your manual gives, in its order, and refit every guard and shield before you restart.

A shovel stops and hands the problem back to you: you feel the root, lever it or move the hole. A bit that hits a root or stone can bind, and Echo says the auger may twist suddenly and forcefully. Echo also says not to operate the unit in excessively rocky ground, and EGO and Ryobi both tell the operator to stop and find another spot when a large obstruction stops the bit. Before you move or restart, complete the full shutdown in the shutdown box above, inspect the bit and let the obstruction be resolved by the method your manual specifies.

Clay needs its own note. EGO and Makita say to dig deep or clay holes in steps, lifting the machine up and down so loose soil leaves the hole. I look at the ground before I pick a tool, because the edge of a hedgerow and the line of an old tree hold roots, and older farmland turns up stones.

Soil Condition

Do not dig in frozen or rock-hard ground or in ground full of roots and stones: the bit can bind and the machine can twist or kick.

Effort, Fatigue and the Number of Holes

Effort is where the machine wins, and the win grows with the number of holes.

A shovel puts the whole load on your back and arms. With a machine the powered flighting carries loosened soil up, while you still lift and control the unit and resist its torque reaction. I count holes: one or two is shovel work, and a long row is machine work. I explain the power head, bit and torque in more detail in how an earth auger works.

A lab simulation of tool torque reaction found that wrist muscle activity was very high even though the torque pulses were short and the peaks low compared with a person’s maximum strength (3). A scoping review linked repeated handle reaction loads from handheld powered tightening tools to physiological changes that point to a higher risk of musculoskeletal problems in assembly workers (4). Neither study used an auger, so I take one general point from them: a tool that can jerk asks for a braced stance and regular breaks.

Fatigue and Vibration

Digging with an auger is heavy, jarring work that twists your arms and back. Take breaks, stop when you are tired or your attention slips, and use the gloves your manual recommends.

When the holes are many, wide or in hard ground, I send the job to a larger machine that comes with its own manual or to a professional, and an earth auger rental is the usual route. A battery model takes a charged pack and a gas model takes the fuel and oil its manual specifies, so read the exact manual before you choose. The trade-offs between the two power types are in my comparison of battery and gas earth augers.

Safety: What Each Tool Asks of You

A shovel and an auger both need a locate first. The machine adds a rotating steel bit, a handle that can twist and, with gas, an exhaust that carries carbon monoxide.

Before You Dig

Call 811 First

Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm responses from every notified utility, including markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Follow state ticket-validity and tolerance-zone rules, preserve markings, and keep augers outside the required clearance area. Near marks, use careful hand digging or another locating method permitted by state rules and the utility; obey any stricter auger-manual prohibition. Arrange separate locating for private services that 811 does not cover (irrigation lines, cables). Do not dig where a service’s location remains uncertain, and do not switch to a larger machine to get around it. No augering depth above a buried service is safe.

The shovel is not exempt. According to PHMSA, planting trees and shrubs is one of the projects that needs the call, the call is free, and the notice period is set by state law. Marks show where lines run, not how deep, so no mark makes a spot safe for a power tool.

Before you start, walk the spot and remove rocks, sticks, wire, hose, stakes and anything else the bit could catch or throw. Identify irrigation lines, drip lines, cables and sprinkler heads before you start, and take loose garden hoses out of the work area. Do not handle or move unidentified cables, pipes or utility lines: keep the auger away from them and contact the utility if their location is uncertain.

Running the Machine

Wear safety glasses with side shields or goggles meeting your manual’s specification, including ANSI Z87.1 where required, and add a face shield where required. Wear hearing protection with gas engines and wherever your manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional protection your manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep hair, clothing, gloves, hands and feet away from moving parts.

If the bit hits a root, a rock or a buried object, it can bind and the machine can twist or kick. Keep firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. Release the throttle or trigger immediately if the bit binds or control is threatened, then complete the full shutdown in the shutdown box above and inspect for damage before restarting. Use reverse only where your manual authorizes it for your model.

Keep children, pets and other people out of the work area and at least the distance specified in your exact manual. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs, and stop if anyone approaches. No distance makes a work area safe on its own: keep watching it.

Never start or run a gas auger indoors or in a garage or shed, even with the doors open. Start and run it outdoors: the exhaust contains deadly carbon monoxide, which has no color, taste or smell. A medical examiner’s review found that small engines, among them pressure washers and generators, produced lethal carbon monoxide in poorly ventilated spaces (5).

A shovel has far fewer hazards. Long digging still strains the back and arms, so take breaks, and the locate rule above applies to it as well.

When a Shovel Is the Better Choice

A shovel is the better choice whenever the hole count is low or the ground is crowded. These are the cases where I reach for it.

  • One tree, shrub or stake. A replacement plum in a row needs a wide, sloped hole, and a tall stake in the vegetable plot needs only a small one.
  • Beside buried lines. I dig by hand next to the drip lines I built, and any reader in the US makes the locate call before the first cut.
  • Where roots are close. A spade feels a root and lets you decide, which a turning bit cannot do.
  • One or two holes of any kind. The machine adds fuel or charging, protective gear and a full set of safety steps to a job that a shovel finishes alone.

When an Earth Auger Fits

An earth auger fits a long row of same-width holes in ground the bit can bore, run by an adult who has read the manual and understands the controls. Never let a child operate one, and never let a helper hold a one-person unit.

  • A fence or post line. Ryobi lists light-duty fencing and posts among the jobs for its cordless auger, and the depth figure in its manual is a maximum for its bit. My roundup of augers for fence post holes compares the machines for that kind of line.
  • Many holes of one width. The bit gives the same diameter every time, which helps when posts or stakes must match. When the holes outgrow a hand-held unit, I compare the next step up in my earth auger vs skid steer auger guide.
  • Hole sizes inside the bit range. The makers’ bits end near 10 inches, so a wide planting hole is outside it.

Picking an auger or shovel for digging holes is easier once you read the exact manual of the machine you plan to use: it prints the bit sizes, the maximum depth and the operator rule for that model. A tractor-mounted digger, a skid steer auger and a drill-driven bit are different tools with their own manuals, and none of them is a homeowner machine, so I leave them out of this choice.

Three Things to Settle Before You Dig

Count the holes first: one or two go to the shovel, and a long row of same-width holes goes to a machine. Measure what goes in each hole next. A tree wants a wide, sloped hole that the makers’ bit sizes cannot make, and a post wants the depth your extension or code source gives. Then check what lies below, because the locate comes before either tool touches the ground.

My own tip is to stake out the whole row before anyone digs, so the locate request lists every planned hole. Read the manual of any machine you buy or rent, and settle the earth auger vs shovel choice one hole at a time rather than for the whole property. If the hole count says machine, my roundup of earth augers for real digging compares gas, corded and battery models.

Frequently Asked Questions

Which is better for digging, a spade or a shovel?

The choice between a spade and a shovel depends on the job, and Colorado State Extension names the shovel for cutting the sides of a planting hole to remove glazing. I keep both within reach on planting day.

Which tool is commonly used for digging holes for tree planting?

A shovel is the tool the extension planting guides point to for finishing a tree planting hole, since Colorado State tells planters to cut the sides with one. A power auger makes a straight-sided bore, which is narrower than the wide, sloped hole those guides describe.

How deep will an auger dig?

An auger digs as deep as the maker’s printed maximum for its bit and no deeper, and Ryobi prints 31 inches as the maximum hole depth for its 40V cordless auger with an 8 inch bit while recommending about 24 inches in its operating instructions. Neither figure is a promise for your soil, and bit extensions work only as the exact manual describes.

What are shovels used for in farming?

On a farm like mine, shovels dig planting holes, set stakes by hand and open the ground where roots or buried lines are close. Colorado State Extension also uses the shovel to cut the sides of a planting hole.

Can you dig a hole in dirt with an ice auger?

An ice auger is made for ice, and digging a hole in dirt with one is a use that only its own manual can approve. If that manual does not list soil, leave the ice auger alone and use a machine made for earth.

References

  1. Wells C, Townsend K, Caldwell J, Ham D, Smiley ET, Sherwood M. Effects of planting depth on landscape tree survival and girdling root formation. Arboric Urban For. 2006;32(6):305-311.
  2. Kozlowski TT. Soil compaction and growth of woody plants. Scand J For Res. 1999;14(6):596-619.
  3. Armstrong T, Bir C, Foulke J, Martin B, Finsen L, Sjogaard G. Muscle responses to simulated torque reactions of hand-held power tools. Ergonomics. 1999;42(1):146-159.
  4. Mazaheri A, Rose LM. Reaction load exposure from handheld powered tightening tools: a scoping review. Int J Ind Ergon. 2021;81:103061.
  5. Hyson BE, Friedman BM, Spear B, Bishop-Freeman SC. Lethal carbon monoxide generated from small internal combustion engines. J Anal Toxicol. 2024;48(8):625-629.

Safety Note: Only an adult who has read the manual and understands the controls should use an earth auger or post hole digger, never a child or anyone tired or impaired. Use the number of people your manual specifies, and keep everyone else out of the work area. The rotating bit can catch hair, clothing and gloves, and it can bind on a root, a rock or a buried object: the machine can then twist or kick in your hands. Stand with firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. If utility contact or a gas leak is suspected, stop work immediately. Do not touch, inspect, free or move the auger or exposed service, and do not attempt the normal hands-on shutdown or disconnect electrical connections in the suspected leak area. Leave the area, keep others away and contact the utility from a safe location; call 911 for a suspected gas leak or immediate danger. Otherwise, release the throttle or trigger immediately if the bit binds or control is threatened, then follow the shutdown procedure. On a two-person unit, both operators must understand the controls and agree on start and stop signals before starting; stop whenever either operator calls stop. Use reverse only where your manual expressly authorizes it. Never touch or clear the bit while it turns. Before you clear or free the bit, change or attach the bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger, complete the shutdown for its power type. Corded electric: release the switch or trigger, wait until the bit has stopped completely, then unplug it from the outlet by the plug, not the cord; before transport or storage, also let the motor cool. Battery: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where the model has one. Gas: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire and secure it away from the plug, and let the engine and muffler cool before touching the bit, engine, muffler or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown instructions in both the bit or attachment manual and the power-head or drill manual. If the bit sticks or material wraps around it, stop and complete the full shutdown before touching or inspecting it. Use only the freeing or clearing method specified in the exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when the exact manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. Wear safety glasses with side shields or goggles meeting the manual’s specification, including ANSI Z87.1 where required; add a face shield where required. Wear hearing protection with gas engines and wherever the manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional footwear protection the manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep them, clothing, hair, hands and feet away from moving parts. Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm that every notified utility has responded with markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Preserve the marks and follow your state’s ticket-validity and tolerance-zone rules. Keep the auger out of the required clearance area; near marks, use careful hand digging or another locating method permitted by state rules and the utility. Follow any stricter prohibition in the auger’s manual. Marks do not show a safe drilling depth. Arrange to locate private irrigation lines, cables and other services that 811 may not cover. If a line’s location remains uncertain, do not dig there. Do not handle or move unidentified cables, pipes or utility lines. Before you start, remove rocks, sticks, wire and loose hoses, and identify irrigation lines, drip lines and sprinkler heads. Keep children, pets and other people out of the work area and at least the distance your exact manual specifies. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs. No single distance is safe for every auger. On a slope or uneven ground, slow down, keep firm footing and follow only your manual’s rule. Do not dig in frozen or rock-hard ground. Before refuelling, complete the full gas shutdown described above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Keep fuel away from smoking, flames, sparks and other ignition sources. Use an approved fuel container, avoid overfilling, secure the cap and follow the manual’s spill-cleanup and restart-location instructions; do not start with a fuel leak. Use the specified fuel and oil arrangement for that engine. Never start or run a gas auger indoors, in a garage or shed, or in an enclosed or poorly ventilated area, even with doors open. Operate outdoors where exhaust cannot accumulate or enter occupied spaces through doors, windows or air intakes. Exhaust contains deadly carbon monoxide. For a corded auger, inspect the cord and extension cord before use and do not use damaged cords or plugs. Use an outdoor extension cord meeting the exact manual’s gauge, length, plug and grounding requirements, and follow its GFCI instructions. Keep connections dry and the cord clear of the bit, heat, oil and sharp edges. Never carry the auger by its cord or wrap the cord around your body. Do not use it in rain or wet conditions prohibited by the manual. Use only manufacturer-approved batteries and chargers for the exact model. Complete the battery shutdown before removing or changing a battery, and keep the switch off and fingers off the trigger when installing one. Do not use damaged or modified batteries or chargers. Keep loose battery terminals away from metal objects, and follow the battery and charger manuals for moisture exposure, charging temperature, cooling and storage. Load and unload only as your manual describes, and store the auger dry and out of children’s reach. Take breaks and stop when you are tired.

Scroll to Top