The 6-inch vs 8-inch auger bit choice comes down to what goes in the hole: a 6-inch bit suits small plants and thin steel posts, and an 8-inch bit gives a 4×4 wood post or a one-gallon pot room to sit. This guide covers earth augers, the powered machines that dig post and planting holes. I replace stone fruit trees in my orchard, so I size a hole from the root ball or post that goes in it. Below you get the fill-room arithmetic, a size chart, planting widths, the extra load a wider bit brings and the machine checks to make first.
6-Inch vs 8-Inch Auger Bit in Short
Pick the 6-inch bit for a small plant, a stake or a thin steel post, and pick the 8-inch bit for a 4×4 wood post or a plant that came in a one-gallon pot. According to Earthquake, a 6-inch hole suits a one-quart pot and steel posts of 1 7/8 or 2 3/8 inches, while an 8-inch hole suits one- and two-gallon pots and a 4×4 wood post. That is a fit for the pot, and the planting width still follows the root ball. Two inches of width change the hole area by about 78 percent, so the larger bit also lifts out far more soil at every inch of depth. For stakes and small plants, I compare the narrower sizes in my guide to 4-inch and 6-inch auger bits.
I hold a 3.5-inch post against a 6-inch circle and the corners nearly touch the edge. Against an 8-inch circle there is a clear gap on every side. That gap is what the larger bit buys you.
Quick Pick
Use 6 inches for small plants, stakes and thin steel posts. Use 8 inches for a 4×4 wood post and as the starting hole for one- or two-gallon plants. Plant holes then follow the root ball width in the extension rule, which can call for a wider hole than either bit digs, and your machine’s manual decides which bits you may fit.
What a 6-Inch and an 8-Inch Bit Actually Differ In
Bit diameter is hole width, and little else follows from it. The two-inch difference changes the hole area, the soil you lift out and the room around whatever you set in the hole. It says nothing about depth, and nothing about how fast a given machine digs. I explain how the power head, bit and torque work together in my guide to how an earth auger works.
Hole Area and Soil Volume
A 6-inch hole has a cross-section of about 28 square inches, and an 8-inch hole has about 50 (pi times the radius squared). Over the same depth, the 8-inch hole holds about 78 percent more soil. That is arithmetic about the hole. The arithmetic does not tell you how long either bit takes on your machine.
| Bit width | Hole cross-section | Soil per inch of depth |
|---|---|---|
| 6 inches | About 28 square inches | Baseline |
| 8 inches | About 50 square inches | About 78 percent more |
Post Hole Auger Bits by Diameter, Length and Depth
Post hole auger bits are sold by diameter and by length, and the two numbers answer different questions. Diameter sets the hole width. Bit length is only the length of the steel, and it does not equal the depth a machine can dig, because makers print a separate depth for each machine. According to Ryobi, its cordless auger lists a maximum hole depth of 31 inches, while the same manual recommends a depth of about 24 inches. If the machine itself is new to you, the basics are in my write-up on parts of an earth auger.
Makers sell more than these two sizes. According to Echo, its earth augers come in 6, 8 and 10 inches. Ryobi’s bit line runs from 4 to 10 inches, and EGO lists bits from 100 to 250 millimeters, which is about 4 to 10 inches. According to Champion, Powermate and Ryobi, their kits come with an 8-inch bit. If you need a wider hole, I cover the 8-inch and 10-inch auger bit choice in a separate guide.
Auger Bit Size Chart for 6-Inch and 8-Inch Bits
The chart below puts the two widths against the jobs that decide the choice. The pot and post rows follow Earthquake’s list, and the room rows are my arithmetic for a 3.5-inch post. Treat them as one maker’s guidance plus geometry, and read your own post or plant instructions before you commit.
| Job | 6-inch hole | 8-inch hole |
|---|---|---|
| Plant in a one-quart pot | On Earthquake’s list | Not on its list for this pot |
| Plant in a one- or two-gallon pot | Not on Earthquake’s list | On Earthquake’s list |
| Steel post, 1 7/8 or 2 3/8 inches | On Earthquake’s list | Not on its list for these posts |
| 4×4 wood post, 3.5 inches square | 1.25 inches of room per side | 2.25 inches of room per side |
| Corner of a 4×4 to the hole wall | About half an inch | About 1.5 inches |
What Size Hole for 4×4 Fence Post Setting
A 4×4 post fits a 6-inch hole, and the fit is tight. An 8-inch hole leaves a collar you can fill. The depth of the hole is a separate decision, and the bit does not make it.
Room Around the Post
A nominal 4×4 measures 3.5 inches square, so its diagonal is about 5 inches. In a 6-inch hole that leaves 1.25 inches on each flat side and about half an inch at each corner. Earthquake says the same thing in its own words: a 4×4 will likely fit a 6-inch hole, but it leaves under half an inch at the widest part for cement or dirt. My roundup of augers for setting 4×4 posts compares the machines that dig for this size of post.
How much fill you need, and whether it is concrete, gravel or tamped soil, depends on the fence maker, the soil and your local code. A bit chart cannot settle that. I read the post or fence instructions first, then I pick the bit that leaves room for what they ask. Set against a gate post, the 6-inch circle looks too tight to me. Gate posts and large root balls are where a wider bit comes up, and I compare that step in 8-inch and 12-inch auger bits.
6-Inch vs 8-Inch Auger Bit for Depth
Depth comes from the frost line, the soil and the job of the post. According to Penn State Extension, a typical line post on a horse fence sits 36 inches deep, and corner and gate posts are larger and often set to 48 inches. The same page says sandy or wet soil calls for deeper posts and that some soils heave with frost and loosen shallow ones. It gives no hole diameter, so the 6 or 8 inches is still your call. For the machines that dig these fence holes, my roundup of augers for fence post holes compares the field.
Deck footings are a code matter. The City of Blaine, Minnesota, for example, asks for footings that reach at least 42 inches below grade, to the frost line, and sizes them by load. Ryobi’s own list of uses for its cordless auger stops at light duty fencing and posts, so ask your building department before you rely on any auger for a footing. If you still want to see machines for footing holes, I compare them in my roundup of augers for deck footing holes.
When 6 Inches Is Too Narrow for Planting Holes
For trees and shrubs, both bits are narrow. According to Colorado State Extension, a planting hole should be three times the root ball diameter. Maryland Extension asks for at least twice as wide, and Illinois Extension for two to three times. Under that two-to-three-times rule, a 6-inch hole fits a root ball of about 2 to 3 inches, and an 8-inch hole one of about 3 to 4 inches. For tree holes that start with a machine, my roundup of augers for planting trees compares the options.
Most nursery containers hold a bigger root ball than that, so for a tree I widen the hole by hand. Earthquake’s pot sizes tell you what physically fits a pot. The planting width still comes from the measured root ball and the extension rule, with hand widening where the bit falls short.
Width Is Only Half the Hole
Depth matters as much as width. In a field trial, deep planting at 15 or 31 centimeters below grade killed half of the Yoshino cherries within two years, while every tree planted at grade lived (1). Colorado State sets the hole depth one to two inches less than the height of the root ball, and Maryland says no deeper than the root ball. A wider bit never excuses a deeper hole.
The walls matter too. Compacted soil restricts root growth, water uptake and aeration around a planting hole (2). Colorado State asks planters to cut down the sides of the hole with a shovel to remove glazing. I finish the wall of any machine-dug hole by hand with a spade, and my comparison of an auger or a shovel covers the digging itself.
Check the Machine Before You Choose a Bit
The bit you want is an option only if your machine lists it. Two machines of the same class can take different bit sizes, and the manual is the only place that says which.
Fit Starts With the Manual
Bits join the power head with a pin: according to Ryobi and EGO the bit locks on with a pin and a pin clip, and according to Champion it uses a clevis pin. Earthquake’s spec sheet lists a 7/8 inch output shaft with a 3/8 inch cross hole. A bit that is not on your maker’s list, or does not match the shaft and pin, stays in the shed. I read the bit list in a manual before I look at the bit. I cover the Earthquake kit supplied with an 8 in bit in my review of the E43 auger.
A drill-driven auger bit is a different tool, and my guide to garden auger drill bits explains how it differs from a machine. It has no engine or motor of its own, so it needs a drill or power head with its own manual, and it is not an earth auger machine.
Bit Size Can Depend on the Soil
Makita’s manual for its DG001G cordless earth auger lists a capacity of 200 millimeters in sandy soil and only 150 millimeters in clay soil, both at low speed, which is about 8 and 6 inches. That is one model’s limit, so check yours before you assume the larger bit works everywhere. According to EGO and Makita, when you drill a deep hole or drill in clay, do not try to dig it all at once: lift the machine up and down so the loose soil can be discharged.
Changing a Bit Starts With a Shutdown
Swapping a 6-inch bit for an 8-inch bit means handling the bit, so the full shutdown comes before your hands go near it. Copy it whole from the box below, for the power type you own.
Full Shutdown Box
Shutdown before you clear or free the bit, change or attach the bit, free a stuck bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger. Never reach toward the bit while it turns, and never clear it or free it with the machine running. Corded electric auger: release the switch or trigger, wait until the bit has stopped completely, then unplug the auger from the outlet by the plug, not the cord. Before transport or storage, also let the motor cool. Battery auger: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where your model has one, and keep it away from the auger. Gas auger: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire (a spark plug cap on some makes) and secure it away from the plug. Let the engine and muffler cool before you touch the bit or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown and isolation instructions in both the bit or attachment manual and the power-head or drill manual (a gas power head needs its own manual’s full shutdown). Only then free a stuck bit or clear wrapped material, using only the method your manual specifies (gloves do not make grabbing sharp wire or cutting edges safe), and check the bit and guards for damage. Do not handle unidentified wire, cables or pipes. Do not use reverse or run the engine or motor to back the bit out unless your manual expressly authorizes it for this task, with both hands on the designated handles and everyone clear of the bit; complete the full shutdown again before any further hands-on work. Add every step your manual gives, in its order, and refit every guard and shield before you restart.
Gas Engines and Carbon Monoxide
Never start or run a gas auger indoors or in a garage or shed, even with the doors open. Start and run it outdoors: the exhaust contains deadly carbon monoxide, which has no color, taste or smell. A medical examiner’s case series tied fatal carbon monoxide poisonings to small engines running in poorly ventilated spaces (3). Allow the muffler and engine to cool before touching them.
How Bit Size Changes the Work and the Risk
A wider hole means more ground to cut, and every rule about where and how you dig stays the same at any size. Read this section before the bit touches the ground, whichever size you pick.
Torque Reaction and Handles
An auger bit can bind, and the machine then pushes back on your arms. According to Echo, drilling holes six inches in diameter or larger may be easier if two people hold the handles on opposite sides, which is that manual’s wording for its own model. Check what your manual says about the number of people before you add a helper.
Binding and Torque Reaction
If the bit hits a root, a rock or a buried object, it can bind and the machine can twist or kick. Keep firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. Release the throttle or trigger immediately if the bit binds or control is threatened, then complete the full shutdown in the shutdown box above. After any bind, stall or strike on a root, rock or buried object, inspect for damage, resolve the cause, repair any damage and meet your manual’s restart conditions before you start again. If you suspect contact with a buried utility, do not touch the auger, bit or exposed service; keep others away and contact the utility or emergency services from a safe location. Use reverse only where your manual authorizes it for your model.
One Person or Two
Use the number of people your exact manual specifies. A two-person unit needs a second person who knows the plan, holds the unit as the manual describes and stays clear of the bit, and both people stop when either calls a stop. A one-person unit is operated by one person; never add a helper to a hand-held unit unless the manual says so.
Lab work on hand-held power tools found that a sudden torque reaction loads the wrist and forearm muscles hard, even when the torque is a small share of a person’s maximum strength (4). A review of assembly-line tightening tools links repeated handle reaction loads to a raised risk of muscle and joint problems (5). Those tools are far smaller than an auger, so I take them as the principle and no measure of your machine.
Fatigue
Digging with an auger is heavy, jarring work that twists your arms and back. Take breaks, stop when you are tired or your attention slips, and use the gloves your manual recommends.
Lines, Ground and People Before You Dig
Buried lines come first, for either bit. Damaging a buried utility is a recognized safety risk and cost in excavation, and trained, careful locating cuts utility strikes (6). According to PHMSA, every state has a one-call center, the call is free, and operators must mark their lines. States set the notice period, so never copy one number for every state.
Buried Lines
Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm responses from every notified utility, including markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Follow state ticket-validity and tolerance-zone rules, preserve markings, and keep augers outside the required clearance area. Near marks, use careful hand digging or another locating method permitted by state rules and the utility; obey any stricter auger-manual prohibition. Arrange separate locating for private services that 811 does not cover (irrigation lines, cables). Do not dig where a service’s location remains uncertain, and do not switch to a larger machine to get around it.
Clear the Area and Check the Ground
Before you start, walk the spot and remove rocks, sticks, wire, hose, stakes and anything else the bit could catch or throw. Identify irrigation lines, drip lines, cables and sprinkler heads before you start, and take loose garden hoses out of the work area. Do not handle or move unidentified cables, pipes or utility lines: keep the auger away from them and contact the utility if their location is uncertain. Do not dig in frozen or rock-hard ground or in ground full of roots and stones: the bit can bind and the machine can twist or kick.
Protective Gear and Bystanders
Wear safety glasses with side shields or goggles meeting your manual’s specification, including ANSI Z87.1 where required, and add a face shield where required. Wear hearing protection with gas engines and wherever your manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional protection your manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep hair, clothing, gloves, hands and feet away from moving parts. Keep children, pets and other people out of the work area and at least the distance specified in your exact manual. Stop if anyone enters that area. No distance makes a work area safe on its own: keep watching it.
Manuals differ on that distance. The Ryobi RY40701 manual says at least 50 feet, and the Echo EA-400/EA-500 manual (2005 edition) says 3 meters (10 feet). If your manual gives no number, keep everyone well clear of the work area as it directs, and stop if anyone approaches. Use the figure in your own manual, and never take another maker’s number as your own.
Which Bit Size to Buy First
Three things carry the decision. The post or plant sets the width, your manual sets the list of bits you may fit, and the safety steps come before the bit touches the ground. For a first bit, I choose the width of the job I do most: an 8-inch bit for wood posts and as the starting hole for container plants, a 6-inch bit for stakes, steel posts and small plants, with plant holes widened to the root ball rule. When you are ready to pick a machine, my roundup of earth augers for real digging lines up gas, corded and battery models.
My own habit is to stand the post or the pot beside a bit before I buy anything, so I see the gap with my own eyes. Then I check the 6-inch vs 8-inch auger bit choice against the manual’s bit list, and I keep the larger root balls for a spade. If you are still weighing a machine against a hand tool, I sort that out by job in my earth auger vs post hole digger guide.
Frequently Asked Questions
What size auger bit do I need?
The auger bit you need is the one that leaves room around whatever goes in the hole and that your machine’s manual lists. According to Earthquake, 6 inches fits small plants and thin steel posts, and 8 inches fits a 4×4 wood post or a one-gallon pot. For plants, widen the hole to the extension root-ball rule, and for posts follow the hole dimensions the post maker specifies.
Is an 8 inch hole big enough for a 4×4 post?
An 8 inch hole is big enough for a 4×4 post, which measures 3.5 inches square, and it leaves about 2.25 inches of room on each flat side. How much of that room you fill with concrete, gravel or tamped soil depends on the fence maker, the soil and local code. Depth is a separate decision, set by the frost line and the post’s job.
How big is an auger?
The earth auger bits that Ryobi, EGO and Echo list run from about 4 to 10 inches wide, and each machine has its own printed maximum hole depth. Bit length is only the length of the steel, so it does not tell you how deep a machine digs. Check the maker’s depth figure for your model.
What are the different types of augers?
The types of augers that dig holes in the ground are gas earth augers, battery earth augers and drill-driven auger bits. Gas and battery earth augers carry their own engine or motor, while a drill-driven bit has none and needs a drill or power head with its own manual. Ice augers and wood auger bits use the same word for different tools.
What size hole for 4×4 deck post?
The hole size for a 4×4 deck post comes from your local building department. Footing diameter and depth depend on the load, the soil and the frost line where you live, so ask for the local footing table before you pick a bit.
References
- Wells C, Townsend K, Caldwell J, Ham D, Smiley ET, Sherwood M. Effects of planting depth on landscape tree survival and girdling root formation. Arboric Urban For. 2006;32(6):305-311.
- Kozlowski TT. Soil compaction and growth of woody plants. Scand J For Res. 1999;14(6):596-619.
- Hyson BE, Friedman BM, Spear B, Bishop-Freeman SC. Lethal carbon monoxide generated from small internal combustion engines. J Anal Toxicol. 2024;48(8):625-629.
- Armstrong T, Bir C, Foulke J, Martin B, Finsen L, Sjogaard G. Muscle responses to simulated torque reactions of hand-held power tools. Ergonomics. 1999;42(1):146-159.
- Mazaheri A, Rose LM. Reaction load exposure from handheld powered tightening tools: a scoping review. Int J Ind Ergon. 2021;81:103061.
- Gallagher AG, Hart M, Cleary D, et al. Proficiency based progression simulation training significantly reduces utility strikes: a prospective, randomized and blinded study. PLoS One. 2020;15(5):e0231979.
Safety Note: Only an adult who has read the manual and understands the controls should use an earth auger or post hole digger, never a child or anyone tired or impaired. Use the number of people your manual specifies, and keep everyone else out of the work area. The rotating bit can catch hair, clothing and gloves, and it can bind on a root, a rock or a buried object: the machine can then twist or kick in your hands. Stand with firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. If utility contact or a gas leak is suspected, stop work immediately. Do not touch, inspect, free or move the auger or exposed service, and do not attempt the normal hands-on shutdown or disconnect electrical connections in the suspected leak area. Leave the area, keep others away and contact the utility from a safe location; call 911 for a suspected gas leak or immediate danger. Otherwise, release the throttle or trigger immediately if the bit binds or control is threatened, then follow the shutdown procedure. On a two-person unit, both operators must understand the controls and agree on start and stop signals before starting; stop whenever either operator calls stop. Use reverse only where your manual expressly authorizes it. Never touch or clear the bit while it turns. Before you clear or free the bit, change or attach the bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger, complete the shutdown for its power type. Corded electric: release the switch or trigger, wait until the bit has stopped completely, then unplug it from the outlet by the plug, not the cord; before transport or storage, also let the motor cool. Battery: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where the model has one. Gas: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire and secure it away from the plug, and let the engine and muffler cool before touching the bit, engine, muffler or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown instructions in both the bit or attachment manual and the power-head or drill manual. If the bit sticks or material wraps around it, stop and complete the full shutdown before touching or inspecting it. Use only the freeing or clearing method specified in the exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when the exact manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. Wear safety glasses with side shields or goggles meeting the manual’s specification, including ANSI Z87.1 where required; add a face shield where required. Wear hearing protection with gas engines and wherever the manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional footwear protection the manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep them, clothing, hair, hands and feet away from moving parts. Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm that every notified utility has responded with markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Preserve the marks and follow your state’s ticket-validity and tolerance-zone rules. Keep the auger out of the required clearance area; near marks, use careful hand digging or another locating method permitted by state rules and the utility. Follow any stricter prohibition in the auger’s manual. Marks do not show a safe drilling depth. Arrange to locate private irrigation lines, cables and other services that 811 may not cover. If a line’s location remains uncertain, do not dig there. Do not handle or move unidentified cables, pipes or utility lines. Before you start, remove rocks, sticks, wire and loose hoses, and identify irrigation lines, drip lines and sprinkler heads. Keep children, pets and other people out of the work area and at least the distance your exact manual specifies. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs. No single distance is safe for every auger. On a slope or uneven ground, slow down, keep firm footing and follow only your manual’s rule. Do not dig in frozen or rock-hard ground. Before refuelling, complete the full gas shutdown described above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Keep fuel away from smoking, flames, sparks and other ignition sources. Use an approved fuel container, avoid overfilling, secure the cap and follow the manual’s spill-cleanup and restart-location instructions; do not start with a fuel leak. Use the specified fuel and oil arrangement for that engine. Never start or run a gas auger indoors, in a garage or shed, or in an enclosed or poorly ventilated area, even with doors open. Operate outdoors where exhaust cannot accumulate or enter occupied spaces through doors, windows or air intakes. Exhaust contains deadly carbon monoxide. For a corded auger, inspect the cord and extension cord before use and do not use damaged cords or plugs. Use an outdoor extension cord meeting the exact manual’s gauge, length, plug and grounding requirements, and follow its GFCI instructions. Keep connections dry and the cord clear of the bit, heat, oil and sharp edges. Never carry the auger by its cord or wrap the cord around your body. Do not use it in rain or wet conditions prohibited by the manual. Use only manufacturer-approved batteries and chargers for the exact model. Complete the battery shutdown before removing or changing a battery, and keep the switch off and fingers off the trigger when installing one. Do not use damaged or modified batteries or chargers. Keep loose battery terminals away from metal objects, and follow the battery and charger manuals for moisture exposure, charging temperature, cooling and storage. Load and unload only as your manual describes, and store the auger dry and out of children’s reach. Take breaks and stop when you are tired.

