A spreader agitator is a moving part inside the hopper of some spreaders, and makers call it by different names, from agitator to auger to pin. In large-scale production, I verified seed drill calibration on weighing trays, so I look for what a maker actually prints about a part before I repeat any claim about it. Below I show where the agitator sits on named models, what each maker says about it, what the manuals say about materials, and the safety steps that apply around it.
What Is a Spreader Agitator?
An agitator is a moving part that sits in the hopper of some spreaders and turns, spins or rocks while the machine works. NC State Extension lists the hopper’s parts as the lid, the sides, a screen or filter, the gate that opens the ports and, in some models, an agitator (1).
Three makers describe the part in their own words. SOLO’s manual for the 421 chest-mount spreader says the “built-in agitator turns steadily during cranking.” the WORX product-page FAQ says that as the WG869 cordless handheld spreader operates, “the agitator spins at the bottom of the tub,” and the WG869 manual lists the agitator as a component. Scotts labels an “Agitator (inside hopper)” on the parts diagram of the EdgeGuard DLX. I cover the crank, strap and hopper of that model in my SOLO 421 chest-mount spreader review.
Agitator, Impeller and Hopper
The hopper is the bin that holds the product, and the agitator is one part inside it. The impeller is a separate part, the plate that throws product on a broadcast spreader, and the deflector is a third part at the edge of the throw. Manuals list them separately: the Agri-Fab 45-0462 parts list gives the hopper (part 41084), the spreader impeller (04367) and the agitator hairpin (48934) a number each. I explain edge guards and side controls in my guide to what a spreader deflector is.
Where the Agitator Sits in the Hopper
The position depends on the model, and a fertilizer spreader agitator is not always where you would look first. Makers place it in the hopper, at the bottom of a tub or inside a bag, and a few mention it only in the assembly steps. My page on spreader hopper parts and care covers the bin itself, its materials and its capacity.
Push Spreaders
On the Scotts Turf Builder EdgeGuard DLX, the quick start guide labels the agitator inside the hopper, on the same diagram as the rotary disk and the rustproof hopper. The Brinly P20-500BHDF-A has a broadcast spreader agitator that the manual calls a rotary agitator and describes as removable, with the line “Use the rotary agitator only if needed.”
The EarthWay 2600A-Plus manual installs an agitator pin in its last assembly step, and the EarthWay 2150 manual puts an agitator at assembly step 16 as well. The Agri-Fab 45-0462 manual lists an agitator hairpin and installs it in the spreader shaft. I examine the 40 lb residential model in my review of the EarthWay 2600A-Plus.
When I open a parts diagram like the Scotts one, I find the agitator first and then follow the path product takes to the plate. I recommend the same habit with your own manual before the first fill.
Handheld and Bag Models
SOLO’s manual for the 421 prints a gear ratio for the crank: each full turn of the handle turns the impeller 7 1/2 times. Ten turns of the handle therefore spin the impeller 75 times. I find the printed ratio useful because it gives you a number to check against. The same manual lists the built-in agitator among the parts and gives no ratio for the agitator itself. I explain the throwing plate’s parts and types in my guide to what a spreader impeller is.
The WORX WG869 manual numbers eleven components, and the agitator is the eleventh, right after the baffle. EarthWay describes the 2750 nylon bag seeder as having a “rocking agitator,” and the listing photo shows it inside the bag. Chapin’s page for the 8700G chest-mount spreader gives its agitator entry as “Gravity.” I put the Chapin chest-mount spreader beside the SOLO in my comparison of SOLO 421 against Chapin 8700G.
Safety Around the Agitator
The agitator is a moving part in the hopper, so every rule in this section applies before a hand goes near it. Complete the stop and make-safe steps in the box below before you fill, reach in, clear, clean, adjust, change a part or leave the spreader.
Safe-State Box: Stop and Make Safe
Emergency first, for a spreader with a battery: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the spreader without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine steps. Stop and make safe before you fill or unload the hopper, reach into the hopper, clear a clog, clean or rinse the spreader, lubricate it, adjust the gate or the pattern, change a part, hitch or unhitch it, charge or change a battery, move it, store it or leave it. Keep your hands, feet, hair and loose clothing away from the impeller, the plate, the agitator, the gears and the wheels while anything can turn. During normal spreading, walk or drive only as your manual and the product label permit; walking behind a push spreader, or pulling a tow-behind unit at the speed its manual describes, is operation, not transport. Walk-behind or hand-crank spreader: close the gate, then stop walking or cranking, and wait until the impeller, plate, agitator and wheels have stopped turning. Battery spreader: release the trigger or close the gate as your manual directs, switch the spreader off, wait until all moving parts have stopped, then remove the battery as the manual directs (on a model with a built-in battery that cannot be removed, such as the WORKPRO X, follow that manual’s own off and storage steps instead, and never open the battery compartment) and keep a removed battery away from the spreader while you work. Follow any additional isolation steps in the exact manual. Keep the gate closed while you fill. Wear all the protective equipment the product label and your manual require while you fill, clean or clear a jam. Clear a clog only with the method in your exact manual. Follow every applicable safety step in your manual, in the order it specifies. Refit every guard and cover, and check that the gate opens and closes before product goes back in.
Moving Parts, Clogs and Turns
Never push, kick or dig product out of the gate or off the plate while anything can turn. If product clumps or bridges in the hopper or the gate clogs, stop and complete the stop and make-safe steps in the safe-state box first, then clear it only with the method in your manual. I follow the same order every time. Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above.
Close the gate before you stop, before you slow down to turn, and whenever you pause, and open it again only after you are walking at the steady pace your manual describes. Do not spread while you turn. NC State Extension gives the same order for operation, with the reason that one wheel usually drives the impeller (2).
Label, Protective Equipment and Hygiene
Read the product label before you open the bag. Follow its directions for the permitted use, the application amount, protective equipment, weather, watering in, access by people and pets, storage and disposal. Using a registered pesticide in a way its label does not allow is against federal law. Follow the spreader’s manual too.
If the product’s instructions and the spreader’s instructions cannot both be followed, do not use that combination; ask the manufacturers for guidance.
Wear all the protective equipment the product label and your spreader’s manual require, and put it on before you open the bag. Wear it every time you fill the hopper, clean the spreader or clear a clog. Protective equipment lowers your exposure; it does not make handling a lawn product safe.
Some manuals add their own lines. SOLO’s manual says to wear safety glasses or eye shields, closed-toed shoes with good traction, snug long-sleeved clothes, non-slip gloves and, if appropriate for the material being spread, a respirator. The WORX manual recommends rubber gloves and substantial footwear, safety glasses, and a face or dust mask if the operation is dusty. Brinly’s manual says to always wear eye protection, substantial footwear and long trousers, and Chapin’s manual says to wear protective eyewear and gloves when handling and applying lawn and garden chemicals.
Wash your hands before eating, drinking, smoking or using the restroom when you work with pesticides. Change your clothes and wash your hands immediately after you apply a product that contains a pesticide, and follow the label’s additional washing and clothing instructions.
Filling, Spills and Storage
Before you fill or unload the hopper, complete the stop and make-safe steps for your spreader in the safe-state box, and keep the gate closed. For fertilizer, fill on a hard surface where spilled granules can be swept up, away from drains and water, as UC IPM advises (3). Follow the product label’s handling and ventilation directions, and wear all the protective equipment the label and your manual require. Fill only to the level your manual allows, and secure the hopper cover or lid if your spreader has one. Keep children and pets away, and never leave a filled spreader where they can reach it.
Keep people and pets away from a spill. Follow the product label and its safety data sheet for collecting, reusing and disposing of spilled product, and wear the protective equipment they require. Never hose or wash granules into a street, a gutter, a drain, a ditch or water, and do not pile spilled product onto the lawn or return contaminated material to the bag. If you cannot manage the spill safely, stay away and call the emergency number on the label. Call Poison Control at 1-800-222-1222 if anyone is exposed, and call 911 for a fire or immediate danger.
Keep fertilizer off pavement and out of drains and surface water. If scattered plain fertilizer lands on a sidewalk, a driveway or a patio, sweep it back onto the lawn before you water, without going over the label rate; collect a concentrated spill instead. For pesticide granules, follow the label’s cleanup instructions.
Follow any buffer requirement that applies and keep fertilizer out of those areas. EPA advises against fertilizing before windy or rainy days, and Purdue advises against fertilizing drought-stressed, dormant or frozen turf (4). Follow the product’s weather and watering directions too.
Keep children, pets and other people away from the area while you fill and spread, and keep them off the treated area for as long as the label says. Store the bag and the filled spreader where they cannot reach them.
Before you store the spreader, complete the stop and make-safe steps in the safe-state box. Store it empty, clean and dry, as your manual describes, with the gate closed. Keep products in their original labeled containers, securely closed, under the storage conditions their labels give, and away from children and pets. Lock pesticides away, apart from fertilizer, food and animal feed, and never put any product into a food or drink container. Store a battery as the battery manual describes.
If someone swallows or is exposed to a lawn product, follow the first-aid section of the product label and call Poison Control at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.
Battery Models
Use only the batteries the maker specifies for your exact spreader, and charge, store and handle them only as your manual describes. Recharge rechargeable batteries only with a charger the manual approves, and never recharge disposable cells. Before you fill the hopper, clear a jam, clean the spreader or change the battery, follow the emergency exception and the applicable stop and make-safe steps in the safe-state box. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger.
This matters for the WORX WG869, the one battery model in this article, because its agitator spins whenever the tool operates. In my view the trigger makes the battery step matter even more. The WORX manual warns you to remove the battery before adjusting, cleaning, servicing or transporting the tool. Before you do any of these, complete the stop and make-safe steps for your spreader in the safe-state box above.
The Names Makers Use for It
Makers do not agree on one word for this part. The table lists what each document calls it, and the word matters when you search your own parts list.
| Model | Word the maker prints | What the maker shows |
|---|---|---|
| SOLO 421 chest-mount | Built-in agitator | Turns steadily during cranking |
| WORX WG869 cordless handheld | Agitator | Component 11; spins at the bottom of the tub |
| Scotts EdgeGuard DLX | Agitator | Labeled inside the hopper |
| EarthWay 2600A-Plus | Agitator pin | Last of 16 assembly steps; remove for rock salt |
| EarthWay 2750 bag seeder | Rocking agitator | Described in the maker’s text, inside the bag |
| Brinly P20-500BHDF-A | Rotary agitator | Removable; use only if needed |
| Chapin 8400C | Auger | Flat or spiked, picked by material |
| Agri-Fab 45-0462 | Agitator hairpin | Installed in the spreader shaft |
| Chapin 8700G chest-mount | Gravity | The entry on the maker’s page |
| Scotts Whirl hand-powered | Not listed | Agitator, screen and cover not listed |
Chapin shows how the naming splits. According to Chapin, the 8400C manual calls the part an auger, a flat one for general turf work and a spiked one “for use with dense materials that have a tendency to clump or have a higher moisture content,” while the maker’s listing calls it a “cast zinc-plated agitator.” I use the manual’s word auger for Chapin and treat agitator as the listing’s word for the same job. When I check a manual, I search for every one of these words, not only agitator. My review of the Chapin 8400C covers that spreader in full.
What Makers Say the Agitator Is For
Makers describe the purpose in marketing language. WORX’s maker page calls the part an “anti-clog agitator” that “keeps materials free-flowing.” EarthWay says the rocking agitator in its 2750 bag seeder “helps the flow of fine seeds to prevent clogs.” Scotts says the hopper and agitator of the EdgeGuard DLX are “designed for smooth product funneling.” My review of Scotts EdgeGuard DLX covers its handle, trigger and edge control.
Those lines are each maker’s statement about its own part. What reaches the lawn depends on the product, the spreader and the setting, and the label and the manual decide those. The bag’s setting chart is a starting point, because spreaders differ (5).
A field study of commercial farm spreaders in North Carolina found wide differences in how evenly different machines spread, and spreader type did not appear to decide it (6). Those were crop-scale machines, so the study says little about a push spreader.
Pro Tip
Read the setting chart for your exact spreader and product, and follow the label’s application directions. The product label gives the application directions, so read it before you set the gate. A setting listed for your exact spreader and product is a starting point, not proof of the amount delivered: follow the spreader’s manual and calibrate for the product, the spreader and the person using it before you apply. Never exceed the label’s application rate.
What Manuals Say About the Agitator and the Material
Where a manual mentions the agitator at all, it often does so in a line about the material in the hopper. Those lines differ from maker to maker, so I give each one with its model.
Rock Salt and Ice Melt
The EarthWay 2600A-Plus manual prints “Remove agitator when using Rock Salt to prevent gearbox damage” at two steps, and it also says not to use powdered materials. The current EarthWay 2150 manual goes further: rock salt and powdered materials “should not be used in this spreader as it will damage the gearbox and can void the warranty.” My review of the EarthWay 2150 covers that 50 lb commercial model.
Chapin’s 8400C manual carries the caution “NOT recommended for use with rock salt.” The Brinly manual allows ice melt with the screen removed and a thorough clean afterward, and it says ice melt “can be highly corrosive.” I read these lines as proof that one part can carry opposite instructions in two manuals, so I follow the manual for the exact model in front of me. The current 2150 prohibition controls for that model. I cover the Brinly P20 in my Brinly P20 push spreader review.
Use ice melt or salt only when both the product’s directions and your spreader’s manual permit it. Salt-based deicers can damage metal, so follow your model’s cleaning instructions after use. Before you clean the spreader, complete the stop and make-safe steps in the safe-state box.
Rinse only if the manual permits it, and dry the spreader as the manual directs. Do not use lawn fertilizer to melt ice. Keep deicing products away from children and pets.
Before you clean the spreader, complete the stop and make-safe steps in the safe-state box, and wear the protective equipment the product label and your manual require. Handle leftover product, cleaning water and residues as the product label directs. Clean the spreader only by a method both the label and the manual permit, and rinse it only where they permit it, keeping product and contaminated wash water out of drains and water supplies. Dry the spreader completely, and lubricate it as its manual directs. If you change products, follow both products’ cleaning requirements: a rinse alone does not show that all residue is gone.
Damp and Clumped Product
The EarthWay 2600A-Plus manual says “Wet fertilizer will also change the spread pattern and flow rate.” A laboratory study of rotary turf spreaders found that when humidity passes a fertilizer’s critical level, the material takes up moisture, its friction on the impeller changes and the pattern skews (7). NC State Extension advises keeping material dry to prevent caking (1).
If product in your hopper has clumped, follow the label first. Then clear it only by the steps in the safe-state box and your manual. The manual and the label settle the question for your product.
How to Check Whether Yours Has One
Some documents print no agitator for a model, and the table shows the Scotts Whirl as an example. A model can also carry the part under another name, as Chapin’s auger shows, while my review of the Scotts Whirl examines the hand-powered model whose documents name no agitator. Work through the manual in this order.
- Find the parts list or the diagram. If you have lost the manual, ask the maker for the manual for your exact model number.
- Look for the part under agitator, auger, pin, hairpin or rocking agitator, and note where the diagram puts it.
- Read the lines about removing it and the lines about materials, including rock salt, ice melt and powdered product.
- Read the stop and make-safe steps for your type of spreader before you touch the hopper.
- Ask the maker when the parts list and the diagram disagree.
I recommend that order because the part name is the one thing makers have not standardized, while the removal and material lines are where the real instructions sit.
What to Check in Your Manual
Three things are worth carrying away. The agitator is a moving part in the hopper, makers name it in different ways, and the manual for your exact model settles whether it is there and what to do with it. My tip is to write the part’s name from your parts list on the inside of the shed door, so the next person who fills the hopper reads the same word you did. Find the agitator in your own manual first, and the rest of the instructions about that part follow from the page it sits on.
Frequently Asked Questions
What does an agitator do in a fertilizer spreader?
An agitator in a fertilizer spreader is a part that moves inside the hopper while the spreader works, and the makers describe its job in their own words. WORX says its agitator spins at the bottom of the tub, and EarthWay says the rocking agitator in its 2750 bag seeder helps the flow of fine seeds. Your manual’s parts list shows what your model has.
Do all lawn spreaders have an agitator?
Not all lawn spreaders have an agitator, and NC State Extension lists one as a part of “some models.” The Scotts EdgeGuard DLX diagram labels one inside the hopper, while the Scotts Whirl placard lists none. Check the parts list for your exact model before you assume either way.
Where is the agitator on a broadcast spreader?
The agitator on a broadcast spreader sits in the hopper, and the exact spot depends on the model. Scotts labels it inside the hopper of the EdgeGuard DLX, WORX says it spins at the bottom of the tub on the WG869, and Brinly lists a removable rotary agitator on the P20-500BHDF-A. Your manual’s parts diagram shows where yours sits.
Can you take the agitator out of a spreader?
Take the agitator out of a spreader only when your manual says so, and complete the stop and make-safe steps in the safe-state box above first. Brinly calls its rotary agitator removable and says to use it only if needed, and the EarthWay 2600A-Plus manual says to remove the agitator when using rock salt. The current EarthWay 2150 manual forbids rock salt altogether.
Does a handheld spreader have an agitator?
Some handheld spreaders have an agitator, and the manual shows which ones. SOLO says the 421 chest-mount has a built-in agitator that turns during cranking, WORX lists one in the WG869 component list, and EarthWay describes a rocking agitator in the 2750 bag seeder. Chapin’s page for the 8700G gives its agitator entry as “Gravity.”
References
- Miller G, Kerns JP, Billeisen T. Organic Lawn Care: Composting and Spreaders. AG-562. NC State Extension; 2026.
- Buhler W, Erickson E, Bruneau A, et al. The Calibration of Turfgrass Boom Sprayers and Spreaders. AG-628. North Carolina Cooperative Extension; 2001, reviewed 2024.
- UC Statewide Integrated Pest Management Program. How to apply fertilizer. In: UC Guide to Healthy Lawns. University of California Agriculture and Natural Resources; 2017.
- Bigelow CA, Tudor WT, Nemitz JR. Facts About Phosphorus and Lawns. AY-334. Purdue University Extension.
- Munshaw G. Calibrating Fertilizer Spreaders for the Home Lawn. AGR-211. University of Kentucky Cooperative Extension Service; 2014.
- Crozier CR, Roberson GT. Granular fertilizer spreader swath uniformity achieved at varying target application rates. Crop Manag. 2014;13(1):1-6.
- Parish RL. The effect of relative humidity on rotary turf spreader patterns. Appl Eng Agric. 1991;7(5):541-544.
Safety Note: Read the product label and your spreader’s manual before handling product. Follow both; if their instructions cannot both be met, do not use that combination. Registered pesticide use must comply with its labeling. A listed spreader setting is a starting point; calibrate as the manual directs and never exceed the label rate. Wear all protective equipment required by the label and manual before opening the container and during filling, cleanup and jam clearing. Wash your hands before eating, drinking, smoking or using the restroom when working with pesticides. After application, change your clothes and wash your hands immediately, and follow the label’s additional washing and clothing instructions. Keep children, pets and other people away during handling and application and off treated areas for as long as the label requires. Emergency first: if a battery becomes unusually hot, swells, hisses, smells unusual or smokes, stop using the spreader without handling or removing the battery. Keep people away and follow the battery manual’s emergency instructions. If it smokes, burns or presents immediate danger, move away and call 911 or the fire department. Otherwise, complete the applicable stop and make-safe sequence before filling, unloading, reaching into the hopper, clearing a jam, cleaning, lubricating, adjusting, changing parts or batteries, hitching, unhitching, transporting, storing or leaving the spreader. Walk-behind or hand-crank: close the gate, stop walking or cranking, and wait for all moving parts to stop. Tow-behind: close the gate, stop the vehicle, set the parking brake, switch off the engine and remove the key as the vehicle manual directs, and wait for the wheels, impeller and agitator to stop before reaching into the hopper or touching the impeller. Battery spreader: release the trigger or close the gate, switch off, wait for moving parts to stop, then remove the battery as the manual directs and keep it away while working. Follow any additional isolation steps in the exact manual. Keep hands, feet, hair and loose clothing away from moving parts. Clear jams only by the manual’s method. Refit guards and covers and check the gate before refilling. With the spreader made safe and the gate closed, fill fertilizer on a hard surface where spills can be collected, away from drains and water. Follow the label’s handling and ventilation directions and the manual’s fill limit. Keep people and pets away from spills. Follow the label and safety data sheet for collection, reuse and disposal; do not spread concentrated spills onto the lawn or return contaminated product to its bag. Sweep scattered plain fertilizer from pavement onto the intended lawn before watering only without exceeding the label rate. Follow the label’s cleanup instructions for pesticide granules. Never wash product into streets, gutters, drains, ditches or water. Observe applicable buffers. EPA advises against fertilizing before windy or rainy days; Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Close the gate before stopping or turning, as the manual directs. Follow both towing manuals for hitching, turning, slopes, speed and load limits; never ride on the spreader or carry passengers on it. Use only batteries specified for the model. Recharge rechargeable batteries only with a charger approved for them, as the manual directs; never recharge disposable cells. After completing the applicable shutdown, handle leftover product, cleaning water and residues according to the product label. Clean only by methods permitted by both label and manual, keeping contaminated water out of drains and water supplies. Rinse only if permitted, then dry and lubricate as directed. A rinse does not establish that all pesticide residue is gone. Use salt or ice melt only when the product directions and spreader manual permit it. Salt-based deicers can damage metal; follow the model’s cleaning instructions. Do not use lawn fertilizer to melt ice. Store the spreader empty, clean and dry as its manual directs. Keep products securely closed in their original labeled containers under their labels’ storage conditions, away from children and pets. Lock pesticides away, separate from fertilizer, food and feed; never use food or drink containers. For human exposure, follow the label’s first-aid instructions, call Poison Control at 1-800-222-1222 and keep the label available. Call 911 for immediate danger.

