How to start an electric pressure washer comes down to one order: hose on and water running first, air purged at the trigger, then power, then spray. Your own manual beats any general list, and the Greenworks GPW3002A and the Westinghouse ePX3500 show the main differences: a power switch against a push button, a GFCI test that one prints and the other does not, and opposite rules on extension cords. I read a washer’s manual and the label on its plug before the first start, the same way I read a sprayer label before a campaign. Below you get the safe-state steps, the four start steps, the GFCI check and what the manuals check when the motor stays quiet.
How to Start an Electric Pressure Washer: The Short Answer
On both washers the water comes on before the power, and the trigger purges the air before you spray. The order of the other steps belongs to each maker. Greenworks has you purge before you connect the washer to power. Westinghouse has you plug in first, purge, lock the trigger and then push the start button. Every hands-on step below comes after the safe-state box in the next section. My guide on how a pressure washer works explains the pump, hose, gun and nozzle behind those steps.
| Step | Greenworks GPW3002A | Westinghouse ePX3500 |
|---|---|---|
| Water before power | Water on first; do not operate without the water supply connected | Water supply on before the power; the pump must not run dry |
| Hose flush | Water flows through the garden hose for 30 seconds before you connect it | Water flushes through the hose for several seconds, then you check the inlet screen |
| Order of plug, purge and start | Water on, trigger pulled to release air, trigger released at a stable stream, then power connected and the switch set to ON | Hose connected and water on, cord plugged in, trigger squeezed to a steady stream, released and locked, then the start/stop button pushed once |
| Power on | Power switch to ON, then pull the trigger | Start/stop push button, pressed once; the pump has an auto-start feature |
| GFCI | Built into the plug; no test steps printed in the manual | Built into the plug; TEST and RESET steps printed, with a monthly test |
| Extension cord | Only an outdoor-rated cord with a rating not below the washer’s | Never use an extension cord |
I recommend reading both makers’ steps even if you own only one of the washers, because the differences show you what to look for in yours. If you run a gas model instead, I cover starting a gas pressure washer from two other maker manuals.
Before You Start: Read the Manual and Make the Washer Safe
Read the pressure washer’s manual before you connect water or power, and follow it. Its warnings, its operator rules and its steps for your exact model come before anything in this article. I keep the plug out of the wall until assembly is finished and the manual’s start page is open next to the washer.
The Safe-State Box
Every hands-on step in this guide starts after the box below. It is the full order for a corded electric washer, and later sections point back to it. If you are still choosing a power source, my guide to gas and electric pressure washers compares fuel, cord and care.
Safe-State Box for a Corded Electric Washer
Stop and make safe before you connect or disconnect a hose, change a nozzle, wand or accessory, clear a clogged nozzle, clean a filter, add detergent, refuel, check the oil, charge or change a battery, drain the washer, move it, store it or leave it. Release the trigger and engage the trigger lock on the spray gun. Corded electric washer: turn the washer off with its power switch and wait until all moving parts have stopped. Every washer, after the steps above for your type: follow your manual’s water-supply shutdown and pressure-relief procedure. Point the gun away from people, pets and electrical equipment at a discharge location your manual and the detergent label permit. Disengage the trigger lock, squeeze the trigger to relieve the trapped pressure as the manual directs, then engage the lock again. Then unplug a corded washer by the plug, not by the cord, with dry hands, or remove the battery from a battery washer as your manual directs and keep it away from the washer while you work. Do not disconnect hoses or change nozzles before the pressure is relieved. If the manual’s procedure does not release the pressure, stop and get service; do not loosen a fitting to release it. Only then disconnect hoses or change nozzles. Where your manual gives a different order for these steps, follow your manual’s order. Follow every applicable step in your manual, in the order it specifies, and check that every hose, fitting and nozzle is attached and undamaged before water or power goes back on.
Protective Equipment, Footing and Who Runs the Washer
Wear safety glasses or goggles and closed footwear when you operate the washer, and put them on before you start. Follow the manual’s additional protective-equipment requirements, including the ear protection Westinghouse shows in its symbol table, and the detergent label’s requirements when you handle detergent. Keep your hands and feet away from the spray. Protective equipment does not make contact with the stream safe. I put the glasses and closed shoes on before I walk to the washer, not after.
Greenworks asks for goggles or safety glasses with side shields and, as necessary, a full-face shield. Westinghouse asks for eye protection, shows eye and ear protection in its symbol table and says never to operate the washer in bare feet, sandals or open-toed shoes. Both makers also rule out running the washer when you are impaired: Westinghouse says not to use it under the influence of alcohol or drugs and to stay alert, and Greenworks says not to operate it when fatigued or under the influence of alcohol or drugs.
Never point the spray at yourself, another person, a pet or any part of the body. Keep your hands and feet away from the nozzle and the stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. Case reports describe infection, compartment syndrome and, in some cases, amputation after a washer injected fluid into tissue (1). A literature review of upper-extremity injection injuries found that injury location and the injected material changed the amputation risk (2). One finger injury at a car wash needed emergency decompression surgery (3), and a case series of three eye injuries ended in surgery and poor final vision for all three patients (4).
Hold and brace the spray gun as your manual instructs, keep firm footing on a surface that is not slippery, and follow your manual’s warning about the push of the gun when you squeeze the trigger. Start the stream away from your feet and from anyone else, and never swing the gun toward people or pets as you turn. Westinghouse adds that surfaces become slippery when wet and extra slippery with a detergent. Keep children, pets and other people away from the work area while the machine runs, and never let a child use the machine. Do not use a pressure washer for a task at height, such as from a ladder, unless your manual expressly permits the equipment and the method.
Assembly Comes First
Before you fit the lance, wand or hose, complete the stop and make-safe steps in the safe-state box above. Both washers arrive unassembled. Greenworks lists the wheels, handle, upper panel, hose hook, cord storage arms, wand and hose in its assembly section, calls for a Phillips screwdriver that the box does not include and says not to power the unit on before assembly is complete. Westinghouse has you snap in the casters, fit the gun holsters, hose retainer and cord retainer, push the lance into the gun and tighten it clockwise without overtightening. Westinghouse also says not to attempt to run the washer if parts that need customer assembly arrived already assembled.
Step 1: Connect the Garden Hose and Flush It
Before you connect or disconnect a hose, complete the stop and make-safe steps in the safe-state box above. Read the water supply rules first, then flush the garden hose, check the inlet screen and connect the hose.
Water Supply Rules the Manuals Print
Both makers describe cold water only. Westinghouse caps the supply at 150 PSI maximum and says the water must come from a water main, not from a lake, pool or pond. Greenworks says the same about the main, says not to use hot water or water from ponds or lakes, and says never to operate the washer without the water supply connected.
Greenworks states that the washer is not suitable for connection to the drinking water mains without a backflow preventer. Westinghouse says some places may bar a direct connection to drinking water and that connections made through a backflow preventer or receiver tank are generally permitted. Follow the local regulations on the hose connection, as both manuals direct.
Flush the Hose and Check the Inlet Filter
Flush the garden hose before it touches the washer. Greenworks says to let water flow through the garden hose for 30 seconds, and Westinghouse says to flush it for several seconds to remove debris. I flush the hose first for the same reason both makers give: whatever sits in the hose should leave through the open end, not reach the inlet screen.
Inspect the high-pressure hose, the spray gun and every fitting before each use, as your manual describes, and do not use a damaged part. Replace a damaged high-pressure hose; never repair or patch it. Connect the hoses and turn on the water before you start the machine, and purge and start it in the order your manual specifies.
Both manuals send you to the inlet filter. Westinghouse says never to connect a garden hose without the screen inside the water inlet in place. Greenworks says that if the filter is damaged, you do not use the machine until it is replaced, and it asks for at least 10 feet of free hose between the water inlet and the water supply. I look at the screen in daylight before the first connection, since a torn one is easy to miss in a shed.
Step 2: Check the GFCI and the Power Cord
A corded washer puts mains electricity beside water, so the electrical step is the one to slow down for. Use the electrical supply and the GFCI protection your manual specifies, and test the GFCI before use according to its instructions. If the washer trips a GFCI or a circuit breaker while you use it, stop using it and have a qualified repair person examine it before you use it again; do not keep resetting it and carry on.
The CPSC warned about fatal shock from electric pressure washers in 1983 and advised a properly grounded receptacle, preferably with GFCI protection. CDC says to test the GFCI first and to have an electrician check a unit that trips a breaker. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Never cut or splice a power cord or an extension cord. Do not use a damaged cord or plug.
What Each Manual Says About the GFCI Test
Westinghouse prints the full test. Plug the power cord into a receptacle, press the TEST button and listen for a click, then press the RESET button to restore power, and repeat the test monthly. It also states that GFCI plugs do not protect against shocks, short circuits and overloads, which is why it keeps its other electrical warnings in force. Greenworks says the GFCI is built into the plug of the power cord and prints no test steps, so follow the instructions that come with the plug. Both makers say that a replacement plug or cord must be an identical part that includes GFCI protection.
Cords, Footwear and Dry Connections
Extension cords are where the two manuals part ways. Westinghouse says never to use an extension power cord, because it causes voltage drop and can burn the motor, so the cord on the washer sets your reach. Greenworks allows an extension cord only if it is intended for outdoor use, marked with an electrical rating not less than the washer’s, and undamaged. Use an extension cord only if your manual permits it, and then only the type and length it names. Greenworks adds an order for disconnecting: take the extension cord off the power strip before you disconnect the washer from the extension cord. If cord reach is your problem, my guide on battery and corded pressure washers shows what the manuals print for each.
Keep every plug and cord connection dry, out of standing water and away from runoff and the area you are washing, and keep the spray away from outlets, wiring and electrical equipment. Both makers say to keep connections dry and off the ground and never to touch the plug with wet hands. Wear closed, rubber-soled footwear that gives some electrical insulation, plus any additional footwear the manual requires; footwear does not replace GFCI protection or the other electrical precautions. I lay the cord out and look it over end to end before I plug it in, because both manuals tell you not to use a damaged one.
Step 3: Purge the Air and Start the Motor
With the hose connected and the water on, read your own manual’s start page again before you touch the gun. The two washers here start in different orders, so each gets its own sequence. My guide on using a pressure washer puts the other steps of a job in order.
Trigger Lock and Grip
Engage the trigger lock on the spray gun whenever you stop spraying, even for a moment, before you set the gun down, and before you walk away or change position. Disengage the lock only for controlled spraying or for the manual’s pressure-relief procedure, with the gun pointed in a safe direction. Follow the picture in your own manual for which way the lock moves. Westinghouse adds a check: after you lock the trigger, squeeze it to make sure it is locked and will not move.
Hold the gun with both hands and point the lance in a safe direction. Greenworks also says that if the trigger depresses without the safety lock being pressed, or stays depressed when released, you replace the spray gun immediately. I do the lock check before every purge, and I keep my feet away from the line of the lance while the water clears.
Greenworks GPW3002A: Purge, Then Power
Greenworks has you turn the water supply on and pull the gun trigger to release the air pressure. When a stable stream of water comes into view, you release the trigger. Only then do you connect the washer to power, set the power switch to on and pull the trigger. I go through that washer in more detail in my Greenworks 3000 PSI washer review.
Westinghouse ePX3500: Plug In, Purge, Lock, Then Push Start
Westinghouse has you connect the garden hose and turn the water on, then unwind the power cord and plug it into a grounded 120 volt outlet. Hold the gun with both hands and point the lance in a safe direction, then release the safety lock and squeeze the trigger until there is a steady stream of water. Release the trigger, lock it, and push the start/stop button once.
The pump has an auto-start feature, and the manual says the motor runs for several seconds and shuts off, which it calls normal. The manual adds that the unit can be pressurized even when you cannot hear the motor and pump running. Squeezing the trigger rapidly makes the auto-start miss a cycle, so Westinghouse asks for slow, deliberate trigger pulls and for turning the washer off after five minutes of inactivity. I treat a silent motor as a pressurized machine, because that is exactly what the manual says it can be. When a washer shuts off for other reasons, my guide on a washer that keeps shutting off lists the causes and safe checks.
On either washer, never leave it on while it is unattended, and never leave it running, connected to mains power or pressurized when you walk away.
Nozzles and Detergent in One Paragraph
Use only the nozzles and accessories your manual permits, following its instructions for the job. Never direct any nozzle at skin, people or animals. Before you change a nozzle, complete the stop and make-safe steps in the safe-state box above. The manual names the nozzle for the job.
Before you add detergent or connect or adjust a detergent accessory, complete the applicable stop and make-safe steps in the safe-state box. Use only the detergents your manual allows, through the detergent system the manual describes, and read the detergent label before you open it. Wear the protective equipment the detergent label requires, and avoid contact of detergent with your eyes and skin. Do not run a detergent that your manual does not name through the pump. Greenworks says soap goes on only through its black soap nozzle at low pressure and lists household detergents, acids, alkalines, bleaches and solvents as products that can damage the pump. Westinghouse says detergent goes through the soap nozzle under low pressure only and warns against thick, gel-like detergents.
Step 4: Stop the Washer and Release the Pressure
Pressure stays trapped in the hose and gun after the motor stops, so the pressure-relief step belongs to every shutdown, not only to maintenance. Start with the safe-state box above, then follow the stop order your maker prints for your machine.
The Stop Order in Each Manual
Westinghouse has you press the start/stop button to stop the washer, then point the gun in a safe direction and pull the trigger to release the pressure. Greenworks has you release the trigger, turn the power switch off, shut off the water supply, squeeze the trigger to release the remaining pressure, engage the lock-out and disconnect the power cord.
Westinghouse adds two limits: never disconnect the high-pressure hose while the system is pressurized, and never let the pump run for more than one minute after you turn off the water supply.
After the Stop
Do not disconnect a hose or change a nozzle until the pressure is relieved and the steps in the safe-state box are done. Check that every hose, fitting and nozzle is attached and undamaged before water or power goes back on. Keep the washer and its cord where children cannot reach them. I move the washer only after the safe-state steps above are done, so nothing is live while I roll it.
Electric Pressure Washer Won’t Start: What the Manuals Check First
When the motor stays quiet, go to the troubleshooting table in your own manual before you open anything. The lines below are the ones the two manuals print, and none of them calls for opening the pump or the motor. Before you do any of them with your hands, complete the stop and make-safe steps in the safe-state box above.
The Motor Does Not Run
I check the power switch and the seating of the plug first, because both sit at the top of the Greenworks list and cost nothing. The Greenworks table lists the power switch being off, the cord not fully in, no power at the outlet and a tripped circuit breaker. If a GFCI or breaker trips during use, the rule from the electrical step applies: stop, and have a qualified repair person examine the washer. With the Westinghouse, check first whether you squeezed the trigger fast, since a rapid squeeze makes the auto-start miss a cycle. Its table also says the motor may run for 1 to 2 seconds, which is normal. My guide on a pressure washer that won’t start goes through further causes and checks.
The Stream Is Weak or Pulsing
Greenworks lists a kinked hose, a clogged inlet filter and a hose of the wrong diameter, which it gives as 1 inch or 5/8 inch. It also says that a pump drawing in air is purged by squeezing the trigger. A nozzle that gives a weak, uneven or pulsing stream may be blocked, and my guide on a pressure washer pulsing lists the other causes the manuals name. Complete the stop and make-safe steps in the safe-state box, then clear the nozzle only with the tool and the method your manual describes: Greenworks names a straight paper clip or cleaning tool and Westinghouse a nozzle cleaning tool or fine needle. Never look into the nozzle or point it at anyone to check it.
The Motor Buzzes
For a buzzing motor, the Greenworks table lists low voltage, residual pressure in the system and voltage loss from an improper extension cord. That last cause is the reason Westinghouse bans extension cords outright. If the cause does not show up in your manual’s table, stop and get service; do not loosen a fitting or open the machine.
What to Remember Before the Next Start
Three things carry over to any corded model. Water goes on before power, the trigger purges the air before the motor runs, and the lock goes on whenever you stop spraying. My own habit is small: I put the manual’s start page on the bench beside the washer for the first run, so the model’s steps are in front of me. After that, the manual’s nozzle table and the label on whatever you wash set the settings, and the safe-state box closes every session. Keep those two things in order and you know how to start an electric pressure washer. If you are still picking a washer, my roundup of the best electric pressure washers compares the corded models by their printed specs.
Frequently Asked Questions
How do you start an electric pressure washer?
After the stop and make-safe steps in the safe-state box above, you start an electric pressure washer in the order its own manual prints: water on and air purged at the trigger before the spray, with the power step placed where your maker puts it. The Greenworks GPW3002A purges before power and the Westinghouse ePX3500 plugs in, purges and locks the trigger before the start button.
Why won’t my electric pressure washer start?
After the stop and make-safe steps in the safe-state box above, check the items in your manual’s troubleshooting table, such as the power switch, the cord, the outlet and a tripped breaker. A washer with auto-start can also miss a cycle if the trigger is squeezed too fast, and a washer that trips a GFCI or breaker needs a qualified repair person to examine it.
How do I set up a pressure washer for a beginner?
After the stop and make-safe steps in the safe-state box above, set up a pressure washer by reading the manual, finishing assembly, putting on safety glasses and closed footwear, and connecting the hose and water in the order the manual gives. Both the Greenworks and Westinghouse manuals say to inspect the inlet filter before the first use.
How to connect a pressure washer to a tap?
After the stop and make-safe steps in the safe-state box above, connect a pressure washer to a tap with a garden hose that you have flushed, with the inlet screen checked, as both manuals describe. Greenworks says the washer is not suitable for connection to the drinking water mains without a backflow preventer, and Westinghouse says such connections are generally permitted through a backflow preventer or receiver tank.
How do you assemble a pressure washer gun?
After the stop and make-safe steps in the safe-state box above, assemble the gun as your manual shows. On the Westinghouse ePX3500, the lance pushes into the gun and tightens clockwise without overtightening, and you pull the collar back to connect the hose, screw the collar on and pull gently on the hose to confirm it is secure.
References
- Funato N, Sugizaki Y, Ri Y, Ichibayashi R. High-pressure injection damage caused by a high-pressure washer. Cureus. 2024;16(1):e52498. doi:10.7759/cureus.52498
- Hogan CJ, Ruland RT. High-pressure injection injuries to the upper extremity: a review of the literature. J Orthop Trauma. 2006;20(7):503-511. doi:10.1097/00005131-200608000-00010
- Choi JH, Choi SY, Hwang JH, Kim KS, Lee SY. Finger compartment syndrome due to a high-pressure washer injury: a case report. World J Clin Cases. 2023;11(13):3017-3021. doi:10.12998/wjcc.v11.i13.3017
- Placide J, Yang MY, Gross AW, Crowell EL. Case series: traumatic ocular lacerations secondary to pressure washers. Am J Ophthalmol Case Rep. 2022;27:101612. doi:10.1016/j.ajoc.2022.101612
Safety Note: Read your pressure washer’s manual before you connect water or power, and follow it. Never point the spray at yourself, another person, a pet or any part of the body. Keep hands and feet away from the nozzle and stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. Wear safety glasses or goggles and closed footwear before operating the washer, plus any additional protection required by the manual and the detergent label. Follow the manual’s instructions for the trigger lock, grip, footing and recoil, and engage the trigger lock whenever you stop spraying. Use only the nozzles, accessories and detergents the manual permits, and never point any nozzle at skin, people or animals. Do not perform a task at height without instructions expressly permitting the equipment and method in the exact manual. Gas models: operate outdoors, never inside a building or a partly enclosed space. Keep the engine at least 20 feet from any window, door or vent, following CDC’s pressure washer guidance and any stricter manual requirement. Exhaust contains carbon monoxide, which cannot be seen or smelled and can kill. Opening doors or windows does not make indoor operation safe. Refuel only with the engine off and cool, following the manual. Corded models: use the manual’s specified electrical supply and GFCI protection, and test the GFCI before use according to its instructions. After an operating GFCI or breaker trip, do not reuse the washer until a qualified repair person has examined it. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Wear closed, rubber-soled footwear that provides some electrical insulation, plus any additional footwear required by the manual; footwear does not replace GFCI protection or the other electrical precautions. Never cut or splice cords. Use an extension cord only as the manual permits. Keep connections dry and away from runoff, standing water and the washing area, and keep spray away from electrical equipment. Battery models: use only the battery and charger the maker specifies for your exact model. Emergency first: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Otherwise, complete the applicable stop and make-safe procedure before hose, nozzle, wand or accessory work, clearing a blockage, cleaning, maintenance, refueling, checking oil, adding detergent, battery changes or charging, draining, moving, transporting, storing or leaving the washer. Follow your exact manual’s procedure and order. Release the trigger and engage its lock. Gas: switch the engine off and wait for it to stop; disconnect the spark plug wire before service as the manual directs, and let hot parts cool before refueling, storage or contact. Corded: switch off and unplug by the plug with dry hands. Battery: switch off, remove a removable battery as the manual directs and keep it away while working; for a built-in battery, follow the manual’s isolation procedure and do not open the battery compartment. Complete the manual’s water-supply shutdown and pressure-relief steps: point the gun in a safe direction at a permitted discharge location, disengage the trigger lock, squeeze the trigger as directed to relieve pressure, then reengage the lock. Do not disconnect hoses or change nozzles until pressure is relieved. If pressure cannot be relieved by the prescribed procedure, obtain service without loosening fittings. Refit and inspect parts before restoring water or power. Replace a damaged high-pressure hose; never repair or patch it. Before you wash, plan how to keep wash water, detergent and debris out of streets, storm drains, ditches and streams, and check with your city or county stormwater office about collection and disposal. Send wash water to landscaping only where local rules and the detergent label permit it and the soil can absorb it without runoff or contamination. Keep children and pets away, and never let a child use the machine. Drain and store the washer as its manual directs. For exposure to a cleaning product, follow the label’s first-aid instructions and call Poison Control at 1-800-222-1222. Call 911 for a fire or immediate danger.

