In the battery powered spreader vs handheld spreader choice, one part differs: a battery motor turns the spinner plate on one, and your hand turns it on the other. The rest is charging, printed weight, hopper size and the extra safety rules a battery brings. In large-scale production, I verified seed drill calibration on weighing trays, so I treat a printed setting as a starting point. I recommend a crank for small beds and short jobs, and a motor only if you will charge it. Below: how each works, a side-by-side table, battery safety and which job fits which.
Battery Powered Spreader vs Handheld Spreader: The Short Answer
This comparison is between two handheld spreaders: one with a hand crank and one with a battery-driven motor. A battery powered hand spreader hands the turning to the motor, and the WORX and WORKPRO models described here run it from a rechargeable lithium-ion pack. The motor adds a pack to charge, a trigger and speed controls to learn and a longer list of safety rules, while the crank keeps one hand busy for the whole job. The pattern on the ground depends on how you carry and walk with a hand-operated spinner (1), so I judge the two types by their printed figures and by the job.
The Quick Verdict by Job
- Small bed, seed patch or short walk: pick the crank. Scotts describes its hand-held class as suited to small areas, and the printed weights stay low.
- You want the motor to do the turning: pick the battery model, and accept that you will charge it and follow its manual’s temperature and storage lines.
- A hopper bigger than a handheld holds: skip both. The maker figures later in this article show how small these hoppers are, and a walk-behind push spreader is the next step.
Every hands-on step below starts with the same stop, so here it is once, whole.
Safe-State Box
Emergency first, for a spreader with a battery: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the spreader without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine steps. Stop and make safe before you fill or unload the hopper, reach into the hopper, clear a clog, clean or rinse the spreader, lubricate it, adjust the gate or the pattern, change a part, charge or change a battery, move it, store it or leave it. Keep your hands, feet, hair and loose clothing away from the impeller, the plate, the agitator, the gears and the wheels while anything can turn. During normal spreading, walk only as your manual and the product label permit; walking and spreading with a handheld spreader is operation, not transport. Hand-crank spreader: close the gate, then stop walking or cranking, and wait until the impeller, plate, agitator and wheels have stopped turning. Battery spreader: release the trigger or close the gate as your manual directs, switch the spreader off, wait until all moving parts have stopped, then remove the battery as the manual directs (on a model with a built-in battery that cannot be removed, such as the WORKPRO X, follow that manual’s own off and storage steps instead, and never open the battery compartment) and keep a removed battery away from the spreader while you work. Follow any additional isolation steps in the exact manual. Keep the gate closed while you fill. Wear all the protective equipment the product label and your manual require while you fill, clean or clear a jam. Clear a clog only with the method in your exact manual. Follow every applicable safety step in your manual, in the order it specifies. Refit every guard and cover, and check that the gate opens and closes before product goes back in.
How a Hand-Crank Handheld Spreader Works
A hand-crank handheld spreader is a small hopper over a spinner plate that your own hand turns. Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. According to Scotts, the Whirl works in four steps: prep, fill, set and go, and I explain the model’s limits in my Scotts Whirl review. You fill the hopper, turn the orange dial, then pull the trigger and turn the crank clockwise while you walk.
Brinly describes the HHS3-5BH, a handheld fertilizer spreader of the same class, the same way, with an extra-long crank at the left of the housing, a trigger handle under the hand and a knob that adjusts the flow gate. According to Brinly, it spreads up to 5 feet, which is the maker’s ceiling for that model and no promise for your yard.
What Carrying Position Does
One study of a hand-operated spinner spreader found the widest swath and the most uniform pattern when the spinner was carried directly in front of the operator with the crank slightly to the right. A non-uniform pattern came from the spinner to the left and the crank in front, and the greatest uniformity came from perimeter travel with the left side of the pattern overlapping the right side of the previous pass (1). That study covers one hand crank design and says nothing about battery models. Settle your carry before the first fill, because the plate sits wherever your arm puts it. My guide to the broadcast spreader pattern explains what it is and what skews it.
Scotts adds that application rates vary with crank and walking speed. I read that line as a reason to keep one steady rhythm for the whole job and to let the product label and the maker’s setting chart decide the setting.
The Chest-Mount Crank Type
The SOLO 421 is a chest-mount crank spreader with a 20 pound capacity and a printed empty weight of 5.5 pounds, according to the SOLO manual. The manual also says each complete revolution of the crank handle turns the impeller 7 1/2 times, so the crank sets the plate speed through a gear. It sits between a hand unit and a push spreader, and I count it as a handheld only in the sense that you carry it. My SOLO 421 spreader review page covers the crank, strap and hopper.
How a Battery Powered Handheld Spreader Works
A battery powered handheld spreader puts a motor behind the spinner plate, so you hold a trigger and walk. Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. The WORX WG869 manual says to press and hold the on/off trigger to start the machine, and it lists a speed-control dial with six levels, a flow-rate adjustment with eight levels and an edge-control deflector. The manual sets the spreading width “by using the speed-control dial and the edge-control deflector”.
The WORKPRO X Series is built the same way with different parts. According to WORKPRO’s manual, it has a trigger, an eight-level flow knob, a six-level speed knob and a throw width lever, and its hopper holds 2.5 liters. The WORX tub holds 0.9 gallons, per its manual. I recommend reading both lists before you buy, because the real differences sit in the controls: how many speed and flow levels there are, and whether a width lever or a deflector sets the throw.
Two Batteries, Two Designs
The WORX kit comes with a removable 20V Max lithium-ion pack (nominal 18 volts, per the manual), a 2.0 Ah battery and a 2 amp charger. According to WORX, the same pack fits its PowerShare family of tools. The WORKPRO has a built-in 7.2 volt, 2.0 Ah lithium-ion pack that charges over USB-C, with the cable in the box and no separate charger block.
That difference matters for safety, because the stop order depends on whether the pack comes out. The safe-state box above covers both cases, and on the WORKPRO, whose pack is built in, it sends you to that manual’s own off and storage steps. I prefer a removable pack because the stop order then has one clear final step, and I judge any battery model by the stop order its manual gives.
What the Dials Mean for You
Both manuals print a settings guide by material class for their flow and speed controls. Treat it as the maker’s starting point. The product label gives the application directions, so read it before you set the gate.
A setting listed for your exact spreader and product is a starting point, not proof of the amount delivered: follow the spreader’s manual and calibrate for the product, the spreader and the person using it before you apply. Never exceed the label’s application rate.
Calibration checks what your own spreader delivers with your own product. Extension guidance says to calibrate for each product and each operator, and that the bag’s setting is a starting point because spreaders differ (2). I verified seed drill calibration the same way at scale, and a handheld deserves the same suspicion.
The Two Types Side by Side
A battery powered hand spreader and a crank model differ in figures that compare only when the basis matches, so each cell gives the maker’s own figure and what it covers. A blank means the maker does not list it.
| Feature | Scotts Whirl | Brinly HHS3-5BH | WORX WG869 kit | WORKPRO X Series |
|---|---|---|---|---|
| Type | Hand crank | Hand crank | Battery, removable pack | Battery, built-in pack |
| Hopper, maker’s figure | Pounds not listed | 5 lb or 2 L | 0.9 gal | 2.5 L |
| Weight, with basis | Not listed | 1.59 lb, basis not stated | 2.27 lb bare tool; about 3.1 lb with battery | 2.62 lb as supplied, battery built in |
| Power | None, hand crank | None, hand crank | 20V Max lithium-ion, 2.0 Ah pack and 2 A charger in the kit | 7.2 V, 2.0 Ah lithium-ion, USB-C cable in the box |
| Controls | Trigger, numbered dial, crank | Trigger handle, flow knob, crank | Trigger, 8-level flow, 6-level speed, edge-control deflector | Trigger, 8-level flow, 6-level speed, throw width lever |
| Cost tier | Budget | Budget | Mid-range | Mid-range |
| Warranty | Not listed | Not listed | 3 years, per the maker’s product page | Not listed |
Pro Tip
Compare weights only on the same basis. A bare tool, a tool with its pack and a built-in-pack unit are three different numbers, and the table keeps them apart.
What the Battery Adds in Weight, Charging and Cost Tier
The battery adds three things a crank never asks for: weight, a charging routine and a higher cost tier. The Whirl and the Brinly sit in the budget tier, while the WORX and the WORKPRO sit in mid-range. The crank costs a busy hand instead, and the motor costs a charged pack on the day of the job. I compare the printed specs of the two crank models in my article on Whirl and Brinly handheld spreaders.
Weight and Where It Comes From
According to WORX, the bare tool weighs 2.27 pounds in the manual and about 3.1 pounds with the battery on the maker’s product page. WORKPRO’s manual gives 2.62 pounds for the whole unit, with the pack built in. Those are three bases, and each weight is before any product goes in the hopper.
Charging and Storing the Pack
Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. The WORKPRO manual gives a charging time of 2 to 4 hours, depending on the output of the power supply, and says it is not possible to work while the pack charges. It also says to charge at least once every 3 to 6 months and never to fully discharge the pack, and it gives a storage charge between 50 and 75 percent. The WORX manual says the pack ships uncharged and must be fully charged before first use, and it sends you to the charger’s own manual for charging time.
A crank has none of this. If you pick a battery model, schedule the charge for the evening before the job.
Battery Safety and Charging
Lithium-ion batteries power both battery models, and OSHA says they “may present several safety and health hazards”, including chemical hazards, stored electrical energy and thermal runaway, which can result in fire, explosions and the release of chemical byproducts (3). OSHA’s controls start with following the manufacturer’s instructions for storage, use, charging and maintenance. The sheet is written for workplaces, and OSHA says there is no specific OSHA standard for lithium-ion batteries, so it guides a garage or a shed and does not regulate it.
A review of thermal runaway modelling adds that safety concerns about thermal runaway constrain wider use of lithium-ion batteries (4). The review covers lithium-ion batteries in general, so its point holds for a pack in a spreader. The battery rules below apply to both models.
Battery Spreader
Use only the batteries the maker specifies for your exact spreader, and charge, store and handle them only as your manual describes. Recharge rechargeable batteries only with a charger the manual approves, and never recharge disposable cells. Before you fill the hopper, clear a jam, clean the spreader or change the battery, follow the emergency exception and the applicable stop and make-safe steps in the safe-state box. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using it without handling or removing it, keep people away and follow the battery manual’s emergency instructions; if it smokes or burns, move away and call 911 or the fire department.
What the WORX Manual Says
The WORX manual says to recharge only with the charger specified by the manufacturer, and it warns that a charger suited to one pack may create a risk of fire with another. It says not to use a battery pack or product that is damaged or modified, not to leave the pack on prolonged charge when not in use, and to keep it clean and dry. Its stated temperature range for using and storing the tool and battery is 32 to 113 degrees Fahrenheit, and for charging 32 to 104 degrees. It also says not to use the tool in rain or in damp or wet locations.
What the WORKPRO Manual Says
The WORKPRO manual says to charge only from a USB power supply of 5 volts DC, not to charge a leaking battery and not to use the charging device in the open. It says to charge in a well-ventilated area away from flammable materials, because batteries can get hot during charging, and not to leave batteries and chargers unsupervised while charging.
It says not to charge the battery below 4 degrees Celsius or above 40 degrees Celsius, and to store it between 0 and 40 degrees Celsius, naming garden sheds and vehicles in direct sunlight as places where the temperature can climb too high. The charging device must be protected from moisture, and the manual says never to expose the product to rain or wet conditions.
The two manuals differ on where to charge: WORX gives no location, and WORKPRO says not in the open. Follow the manual of the model in your hand, never the other one. I recommend that you keep a lithium-ion spreader out of a hot shed, and I skip any battery model whose charger the manual does not name. WORX’s temperature ranges belong to WORX alone, and WORKPRO’s to WORKPRO.
What Each Maker Allows in the Hopper
The manual and the label decide what goes in the hopper, never the shop page. Read the product label before you open the bag. Follow its directions for the permitted use, the application amount, protective equipment, weather, watering in, access by people and pets, storage and disposal.
Using a registered pesticide in a way its label does not allow is against federal law. Follow the spreader’s manual too. If the product’s instructions and the spreader’s instructions cannot both be followed, do not use that combination; ask the manufacturers for guidance.
According to the WORX manual, its spreader is intended for spreading grass seeds, fertilizers, rock salt or de-icer outdoors. The WORKPRO manual says it suits lawn seeds, agricultural fertilizers, animal feed, deicers and rock salts, and that it “must not be used for distributing chemicals, pesticides, herbicides, liquids, and powder”. That line settles the question for weed products in that model, whatever a sales page says. A battery powered fertilizer spreader takes only what its manual lists, and Brinly lists ice melt, fertilizer and grass seed for its crank HHS3-5BH. If ice melt is the job, my list of spreaders for ice melt is the place to start.
Use ice melt or salt only when both the product’s directions and your spreader’s manual permit it. Salt-based deicers can damage metal, so follow your model’s cleaning instructions after use. Before you clean the spreader, complete the stop and make-safe steps in the safe-state box.
Rinse only if the manual permits it, and dry the spreader as the manual directs. Do not use lawn fertilizer to melt ice. Keep deicing products away from children and pets.
Where a product contains a pesticide, hygiene matters too. Wash your hands before eating, drinking, smoking or using the restroom when you work with pesticides. Change your clothes and wash your hands immediately after you apply a product that contains a pesticide, and follow the label’s additional washing and clothing instructions.
Protective Equipment
Wear all the protective equipment the product label and your spreader’s manual require, and put it on before you open the bag. Wear it every time you fill the hopper, clean the spreader or clear a clog. Protective equipment lowers your exposure; it does not make handling a lawn product safe.
The WORX manual recommends rubber gloves and substantial footwear outdoors, says to use safety glasses and to use a face or dust mask if the work is dusty, and forbids loose clothing and jewelry. The WORKPRO manual says to wear full eye and hearing protection while operating it, heavy long trousers, boots and gloves, head protection where objects can fall, and eye protection and a face filter mask with fertilizers and dusty products. The SOLO manual says to always wear safety glasses or eye shields, closed-toed shoes with good traction, snug long sleeves, non-slip gloves, and a respirator if appropriate for the material being spread.
Filling, Spills and Runoff
Before you fill or unload the hopper, complete the stop and make-safe steps for your spreader in the safe-state box, and keep the gate closed. For fertilizer, fill on a hard surface where spilled granules can be swept up, away from drains and water (5). Follow the product label’s handling and ventilation directions, and wear all the protective equipment the label and your manual require.
Fill only to the level your manual allows, and secure the hopper cover or lid if your spreader has one. Keep children and pets away, and never leave a filled spreader where they can reach it.
Spills
Keep people and pets away from a spill. Follow the product label and its safety data sheet for collecting, reusing and disposing of spilled product, and wear the protective equipment they require. Never hose or wash granules into a street, a gutter, a drain, a ditch or water, and do not pile spilled product onto the lawn or return contaminated material to the bag. If you cannot manage the spill safely, stay away and call the emergency number on the label. Call Poison Control at 1-800-222-1222 if anyone is exposed, and call 911 for a fire or immediate danger.
Runoff, Hard Surfaces and Water
Keep fertilizer off pavement and out of drains and surface water. If scattered plain fertilizer lands on a sidewalk, a driveway or a patio, sweep it back onto the lawn before you water, without going over the label rate; collect a concentrated spill instead. For pesticide granules, follow the label’s cleanup instructions. Follow any buffer requirement that applies and keep fertilizer out of those areas. EPA advises against fertilizing before windy or rainy days, and Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Follow the product’s weather and watering directions too.
I treat a concrete work pad beside a shed as the first place stray granules cause trouble, because pavement is where runoff starts. The same goes for a gravel yard and the path to the door.
Walking, Stopping and Turning
Close the gate before you stop, before you slow down to turn, and whenever you pause, and open it again only after you are walking or driving at the steady pace your manual describes. Do not spread while you turn. Extension guidance for rotary spreaders says to start walking before opening the gate and to close it before stopping (6). On a trigger model, release the trigger as your manual directs.
Keep children, pets and other people away from the area while you fill and spread, and keep them off the treated area for as long as the label says. Store the bag and the filled spreader where they cannot reach them. If someone swallows or is exposed to a lawn product, follow the first-aid section of the product label and call Poison Control at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.
Which One Fits Your Job
The job decides between a crank and a motor, and the printed hopper figures set the ceiling for both. A handheld hopper is a small bin, so these units suit small, contained work.
Small Beds and Seed Patches
For a vegetable bed with packed-soil paths, I recommend a handheld over any push spreader. The crank needs no charging, and a bed with narrow paths leaves no room for wheels. I pick the crank first for jobs like that, and the motor only if turning a handle for the whole job is the part I want to hand off.
When the Crank Hand Gets in the Way
A motor frees the hand that would be cranking, and the trigger replaces the steady turning. That is a physical difference in who does the turning. A sore wrist or tired arm means stop and rest, so I never tighten my grip and keep going.
A Job Beyond a Handheld Hopper
The makers print small spreader hoppers: 5 pounds or 2 liters for the Brinly, 0.9 gallons for the WORX, 2.5 liters for the WORKPRO and 20 pounds for the SOLO. When the job needs a bigger hopper than the model you chose, a push spreader is the next step, and the label rule still comes first. Where the label forbids the use, no spreader is the answer.
Who Should Skip Each Type
- Skip the crank if turning a handle for the whole job is the part you cannot do.
- Skip the battery model if you will not charge it before the job or follow its manual’s temperature and storage lines.
- Skip both if the manual is missing, because a model with no manual leaves you without its stop order.
Cleaning and Storing Each Type
Before you clean the spreader, complete the stop and make-safe steps in the safe-state box, and wear the protective equipment the product label and your manual require. Handle leftover product, cleaning water and residues as the product label directs. Clean the spreader only by a method both the label and the manual permit, and rinse it only where they permit it, keeping product and contaminated wash water out of drains and water supplies.
Dry the spreader completely, and lubricate it as its manual directs. If you change products, follow both products’ cleaning requirements: a rinse alone does not show that all residue is gone.
The two battery manuals give different cleaning lines. WORX says to wipe the tool clean with a dry cloth. WORKPRO says not to use water to clean it, because of a risk of electric shock, and not to use cleaning agents or solvents, and it says to use a soft-bristled brush, wipe with a damp cloth and dry thoroughly. The Whirl’s placard and the Brinly’s maker page print no cleaning step, so a crank model follows the label and its own manual. Extension guidance for fertilizer spreaders says to wash after each day’s use, dry completely and lubricate as the owner’s manual specifies (7), and a battery model’s manual overrides that advice.
Dust and Clogs
Never push, kick or dig product out of the gate or off the plate while anything can turn. If product clumps or bridges in the hopper or the gate clogs, stop and complete the stop and make-safe steps in the safe-state box first, then clear it only with the method in your manual.
Storage
Before you store the spreader, complete the stop and make-safe steps in the safe-state box. Store it empty, clean and dry, as your manual describes, with the gate closed. Keep products in their original labeled containers, securely closed, under the storage conditions their labels give, and away from children and pets. Lock pesticides away, apart from fertilizer, food and animal feed, and never put any product into a food or drink container. Store a battery as the battery manual describes.
Choosing Between a Crank and a Motor
A handheld hopper is small, the manual decides what goes in it, and a battery brings charging and storage rules a crank never has. My tip is to read the stop order in the manual before you buy, because a pack you cannot remove changes it. That is how I settle the battery powered spreader vs handheld spreader choice: a crank for a small bed, a motor when I want my hand free of the crank. I compare both options for small jobs in my handheld spreader picks, which cover crank and battery models.
Frequently Asked Questions
What is the difference between a battery powered spreader and a handheld spreader?
A battery powered spreader differs from a hand-crank unit in what turns the spinner plate: a motor on a battery in the first, your hand on a crank in the second. The battery model adds a pack to charge and its own safety rules, while the crank adds a busy hand.
What is a battery powered hand spreader?
A battery powered hand spreader is a small carried unit with a hopper, a spinner plate and a battery-driven motor that you run with a trigger. The WORX WG869 and the WORKPRO X Series are two examples, and both charge a lithium-ion pack under their own manual’s rules.
Can you use a battery powered spreader for fertilizer?
A battery powered spreader holds fertilizer only where its manual lists it, and the product label and the manual decide the rest. The WORX manual names fertilizers among its intended uses, and the WORKPRO manual names agricultural fertilizers.
Can you use a battery powered spreader for grass seed?
A battery powered spreader takes grass seed only where its manual names seed. The WORX manual names grass seeds and the WORKPRO manual names lawn seeds, and the manual’s own settings guide gives the starting point.
How do you charge a battery powered spreader?
You charge a battery powered spreader only as its manual describes, with the charger the maker specifies. Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. The WORKPRO charges over USB-C from a 5 volt supply and says not to charge in the open, while the WORX manual says the pack ships uncharged and must be fully charged before first use.
References
- Wolf DD, Smith ES. Uniformity of seed and fertilizer distribution with a hand-operated spinning spreader. Trans ASAE. 1979;22(4):761-762.
- Munshaw G. Calibrating Fertilizer Spreaders for the Home Lawn. AGR-211. University of Kentucky Cooperative Extension Service; 2014.
- Occupational Safety and Health Administration. Lithium-ion Battery Safety. Fact Sheet DTSEM FS-4480. US Department of Labor; January 2025.
- Wang G, Ping P, Kong D, et al. Advances and challenges in thermal runaway modeling of lithium-ion batteries. Innovation (Camb). 2024;5(4):100624.
- UC Statewide Integrated Pest Management Program. How to apply fertilizer. In: UC Guide to Healthy Lawns. University of California Agriculture and Natural Resources; 2017.
- Buhler W, Erickson E, Bruneau A, et al. The Calibration of Turfgrass Boom Sprayers and Spreaders. AG-628. North Carolina Cooperative Extension; 2001, reviewed 2024.
- Miller G, Kerns JP, Billeisen T. Organic Lawn Care: Composting and Spreaders. AG-562. NC State Extension; 2026.
Safety Note: Read the product label and your spreader’s manual before handling product. Follow both; if their instructions cannot both be met, do not use that combination. Registered pesticide use must comply with its labeling. A listed spreader setting is a starting point; calibrate as the manual directs and never exceed the label rate. Wear all protective equipment required by the label and manual before opening the container and during filling, cleanup and jam clearing. Wash your hands before eating, drinking, smoking or using the restroom when working with pesticides. After application, change your clothes and wash your hands immediately, and follow the label’s additional washing and clothing instructions. Keep children, pets and other people away during handling and application and off treated areas for as long as the label requires. Emergency first: if a battery becomes unusually hot, swells, hisses, smells unusual or smokes, stop using the spreader without handling or removing the battery. Keep people away and follow the battery manual’s emergency instructions. If it smokes, burns or presents immediate danger, move away and call 911 or the fire department. Otherwise, complete the applicable stop and make-safe sequence before filling, unloading, reaching into the hopper, clearing a jam, cleaning, lubricating, adjusting, changing parts or batteries, hitching, unhitching, transporting, storing or leaving the spreader. Walk-behind or hand-crank: close the gate, stop walking or cranking, and wait for all moving parts to stop. Tow-behind: close the gate, stop the vehicle, set the parking brake, switch off the engine and remove the key as the vehicle manual directs, and wait for the wheels, impeller and agitator to stop before reaching into the hopper or touching the impeller. Battery spreader: release the trigger or close the gate, switch off, wait for moving parts to stop, then remove the battery as the manual directs and keep it away while working. Follow any additional isolation steps in the exact manual. Keep hands, feet, hair and loose clothing away from moving parts. Clear jams only by the manual’s method. Refit guards and covers and check the gate before refilling. With the spreader made safe and the gate closed, fill fertilizer on a hard surface where spills can be collected, away from drains and water. Follow the label’s handling and ventilation directions and the manual’s fill limit. Keep people and pets away from spills. Follow the label and safety data sheet for collection, reuse and disposal; do not spread concentrated spills onto the lawn or return contaminated product to its bag. Sweep scattered plain fertilizer from pavement onto the intended lawn before watering only without exceeding the label rate. Follow the label’s cleanup instructions for pesticide granules. Never wash product into streets, gutters, drains, ditches or water. Observe applicable buffers. EPA advises against fertilizing before windy or rainy days; Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Close the gate before stopping or turning, as the manual directs. Follow both towing manuals for hitching, turning, slopes, speed and load limits; never ride on the spreader or carry passengers on it. Use only batteries specified for the model. Recharge rechargeable batteries only with a charger approved for them, as the manual directs; never recharge disposable cells. After completing the applicable shutdown, handle leftover product, cleaning water and residues according to the product label. Clean only by methods permitted by both label and manual, keeping contaminated water out of drains and water supplies. Rinse only if permitted, then dry and lubricate as directed. A rinse does not establish that all pesticide residue is gone. Use salt or ice melt only when the product directions and spreader manual permit it. Salt-based deicers can damage metal; follow the model’s cleaning instructions. Do not use lawn fertilizer to melt ice. Store the spreader empty, clean and dry as its manual directs. Keep products securely closed in their original labeled containers under their labels’ storage conditions, away from children and pets. Lock pesticides away, separate from fertilizer, food and feed; never use food or drink containers. For human exposure, follow the label’s first-aid instructions, call Poison Control at 1-800-222-1222 and keep the label available. Call 911 for immediate danger.

