Affiliate Disclosure: Garden Power Scout is a proud participant in the Amazon Services LLC Associates Program. As an Amazon Associate, we earn from qualifying purchases, at no extra cost to you.
The Chapin 15 vs 25 gallon sprayer choice comes down to tank size, because the Chapin 97200E EZ Mount 15-Gallon 12V Spot Sprayer and the Chapin 97254 25-Gallon Mounted ATV/UTV Spot Sprayer are otherwise close: both are 12V vehicle-supply spot sprayers that Chapin builds around a 1.0 GPM pump, a 60 PSI ceiling and a 6 inch tank opening. I recommend the 15 gallon 97200E for most buyers, and the 25 gallon 97254 when fewer refill trips matter more than a lighter load on the vehicle. I trained in plant protection, so I read a spot sprayer the way I read any pump on the farm: what powers it, what it holds and what can go wrong with the wiring.
Chapin 15 vs 25 Gallon Sprayer: The Short Answer
The 97200E is the better buy for most vehicles and most yards, because 15 gallons is the smaller load on a rack and Chapin prints the same pump rating, pressure ceiling and opening for both. The 97254 earns its place when you spray often enough that stopping to refill is the real cost. Neither one runs on a battery of its own. Both take their power from a vehicle’s 12V supply, so a suitable vehicle is part of the purchase, and the vehicle’s manual and the sprayer’s manual govern how you run it.
| Row | Chapin 97200E | Chapin 97254 |
|---|---|---|
| Sprayer type | 12V ATV/UTV mounted spot sprayer | Mounted ATV/UTV spot sprayer, 12V (97400E) |
| Power source | 12V vehicle supply through a wire harness with an in-line fuse; no battery or charger in the product | 12V vehicle supply with quick-connect alligator clips (97400E); no battery or charger in the product |
| Tank capacity | 15 gallon poly tank, 6 in opening | 25 gallon poly tank, 6 in opening |
| Pump and pressure | Diaphragm pump, 1.0 GPM, up to 60 PSI; the pump switch shuts the pump off at 60 PSI | 1.0 GPM diaphragm pump, up to 60 PSI on Chapin’s listing; the 97400E manual prints the 60 PSI pump switch |
| Filters | Three, per Chapin: in-tank, shut-off and filter basket | Three, per Chapin’s 97400E page: in-tank, shut-off and filter basket |
| Wand and shut-off | 18 in poly wand, poly shut-off with lock-on | 19 in poly wand on Chapin’s 97400E page; the listing gives no wand length |
| Hose | 180 in reinforced PVC, per Chapin | 192 in on the listing; 180 in on Chapin’s 97400E page |
| Nozzles | Chapin’s page lists three: adjustable brass, poly cone, poly fan; the manual says a #18 tip is standard | Chapin’s 97400E page lists an adjustable stream to cone nozzle; the manual says a #18 tip is standard |
| Weight | Not listed | Not listed |
| Battery and runtime | Not applicable (vehicle supply) | Not applicable (vehicle supply) |
| Warranty | One year after purchase, per the manual | One year after purchase, per the 97400E manual; 1-year limited on the listing |
The two rows that decide it are the tank and the weight you ask your vehicle to carry, because the pump, the pressure ceiling and the opening match. A row marked 97400E comes from Chapin’s 25 gallon sibling, and the next section explains why.
What Is Actually Different Between the 97200E and the 97254
The tank is the one difference Chapin prints with confidence: 15 gallons against 25. The wand and hose figures differ slightly between pages, and the rest of the table matches.
Chapin’s manual covers the 97200E and the 97400E, a 25 gallon unit with the same pump and pressure figures. It does not name the 97254, so every 97254 figure marked 97400E belongs to that sibling, which the 97254 is likely but not proven to match. The wand differs by one inch (18 against 19) and the hose figure for the 97254 is 192 inches on one page and 180 on another. I treat those as small and check them on the unit I receive. I set the 97254 against the Master Manufacturing Deluxe in my head-to-head of two 25 gallon spot sprayers.
Power, Wiring and the First Water Fill
Both sprayers draw their power from a vehicle’s battery, so the wiring is the part of this job that can hurt the machine, and the first water fill is where I check it. Chapin’s manual for the 97200E and the 97400E says to ensure the wiring harness does not become pinched or damaged, because that may damage the pump or cause the harness to overheat, resulting in melt down or fire. The harness carries an in-line fuse, and the manual lists a 7.5 amp replacement and a correct voltage of 12 to 13V.
Full Shutdown
Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Shutdown before you open the tank, fill or refill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, move, store or leave the sprayer. Never point the wand at yourself, another person or a pet. During normal spraying, move only as the equipment manuals and the product label permit; walking while spraying with a backpack unit, or driving a mounted boom at the spraying speed its manual describes, is operation, not transport. Never ride while operating a hand-held wand or lance. 12V vehicle sprayer (ATV, UTV, cart or tow-behind): first stop and secure the vehicle as its manual directs. Then release the trigger, close the wand or boom valve and switch the pump off at its switch. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies. Reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the protective equipment the product label requires while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual; never clear a nozzle with your mouth and never by blowing into it. Add every step your manual gives, in its order. Refit every part, close the lid and check for leaks with clean water before product goes back in.
Chapin’s manual prints no pressure-relief procedure, so contact Chapin for the procedure for your exact model before you open the tank or loosen any part. Until you have it, do not open the tank or loosen anything, because the shutdown box cannot supply the missing step.
Once you have it, I follow the box above before I touch a hose or a clamp. With the vehicle secured and the supply disconnected as the box says, I fill the 97200E with clean water, close the lid and reconnect only when I am ready to test. Then I watch the hose clamps, the drain plug and the pump head for drips without touching a pressurized part. Those are the places the manual’s troubleshooting table names for leaks, and a drip means stop and repeat the full shutdown.
The pump is a diaphragm pump, which North Dakota State University Extension describes as commonly used with ATV sprayers (1). Chapin prints 60 PSI as the maximum and says the pump switch shuts the pump off there. The manual adds that pressure can only be adjusted by adjusting the nozzle.
A maximum is the machine’s limit and never a target. Kansas State’s extension publication on field sprayers says higher pressure makes many more droplets under 100 microns and advises staying below 40 to 45 PSI (2). That advice is for field sprayers, and your product label and the nozzle’s maker set the pressure for your job.
Winner: a tie, because the manual that covers the 97200E and the 97400E gives the same wiring warning and the same 60 PSI pump switch for both.
Tank Size, Refills and Load on the Vehicle
Ten gallons is the gap, and it shows up in two ways: how often you stop to refill and how much liquid your vehicle carries. Complete the full shutdown in the shutdown box above before you fill either tank, and fill only to the level the manual allows.
Refills
On a Chapin ATV sprayer the tank is the refill clock. A 25 gallon tank holds ten more gallons than a 15 gallon tank, so the 97254 asks for fewer stops at the water source on a long job. How far a tank goes depends on your product label and your nozzle. In the orchard I notice the walk back to the yard more than the tank, so that is the cost I weigh first.
Winner: Chapin 97254, because a 25 gallon tank means fewer refill stops for the same job.
Load on the Vehicle
According to the U.S. Geological Survey, a gallon of fresh water weighs about 8.3 pounds, so water alone is about 125 pounds in the 15 gallon tank and about 208 pounds in the 25 gallon tank. That figure is for water only, not for a product mix, and it leaves out the tank, pump and wand. Stay within the rack and tow capacity in your vehicle’s owner’s manual, because Chapin prints no load figure and says only that the sprayer is designed to be attached to stable surfaces.
Sloshing liquid shifts weight and changes how the vehicle handles. Montana State University Extension advises a spray tank with internal baffles and the lowest practical center of gravity. A trauma-center series of ATV crashes linked uphill travel strongly with backward rollovers (3). Chapin prints no baffle for either tank, so a bigger tank adds more moving liquid to every turn.
Montana State University Extension also advises not to ride and spray if you have to hold a wand or lance. Both of these units come with a hand wand, so spraying happens with the vehicle stopped as its manual directs.
Winner: Chapin 97200E, because it puts the smaller weight of liquid on the rack.
Tank Opening, Filters and Cleaning Access
The opening is the same 6 inch width on both tanks, so the bigger tank does not make filling any easier. Before you open either tank, complete the full shutdown in the shutdown box above.
On the 97200E the 6 inch opening lets me look straight down at the suction supply screen inside the tank, which the manual tells you to inspect regularly and flush with water. Chapin says each sprayer carries three filters: one in the tank, one in the shut-off and a filter basket in the cap. On the 97254 that is the part I look at first, because a 25 gallon tank hides more of its own bottom.
Before you clean the sprayer, complete the full shutdown in the shutdown box above, and wear the protective equipment the label and manual require. Chapin’s manual then says to fill the sprayer part way with water after use, start the sprayer and let clear water run through the plumbing and out the wand. It adds that you should use a chemical neutralizer, repeat the cleaning and flush the entire sprayer with the neutralizing agent, and follow the chemical manufacturer’s disposal instructions for all wash or rinse water, so the product label governs the rinse water.
Complete the full shutdown again before you open the drain plug, empty the tank or store it. The manual’s rinse note says to store the tank upside down in a warm, dry place. A bigger tank takes longer to drain, so I plan the rinse around the drain plug.
Winner: a tie, because Chapin prints the same opening, the same filters and the same rinse steps for the 97200E and the 97400E.
Wand, Hose, Trigger and Nozzles
The wand and the shut-off are where you hold the sprayer, and they differ by an inch on paper. Chapin lists an 18 inch poly wand for the 97200E and a 19 inch wand for the 97400E, which the 97254 is built like.
The 97200E has a poly shut-off with a lock-on feature, and in a gloved hand the thumb finds the lock without looking. The 18 inch wand puts the nozzle only a forearm past my hand, so beside a plum row I stand close to the drip line instead of reaching. With clean water against the shed wall, I look at the pattern the adjustable brass nozzle makes before I judge the other two Chapin lists, a poly cone and a poly fan. Before I change any nozzle, I complete the full shutdown in the shutdown box above.

The 97254 comes with a longer hose on its listing, 192 inches against Chapin’s 180 on the 97400E page, and Chapin lists one adjustable stream to cone nozzle for its 25 gallon sibling, the 97400E. Hose length is a number I check when the box arrives, because a hose that is a foot longer is also a foot more to route away from a rack edge. Before I route the harness, I complete the full shutdown in the shutdown box above, including securing the vehicle, and then I lay it out where nothing can pinch it, as the manual warns.

Winner: Chapin 97200E, because Chapin prints three nozzles and a lock-on shut-off for it, while Chapin’s 97400E page, the nearest match for the 97254, lists one nozzle.
Choose the Chapin 97200E If
The 97200E fits the buyer who wants the lighter load and the better-documented unit. Choose it if one or more of these is you:
- Your rack limit is modest: 15 gallons of water is about 125 pounds before the tank and pump, and your vehicle’s manual sets what the rack may carry.
- You spray in short runs: the job ends near the place where you fill, so extra refills cost little.
- You want the printed spec: Chapin’s page and manual both name this model, with three nozzles and a lock-on shut-off.
It is the unit I put on a small property with a vehicle that carries a tank easily, and I recommend it to most buyers. Skip it if you refill many times in one session and your vehicle’s manual allows the heavier tank. I also put the 97200E next to Master Manufacturing’s 15 gallon unit in my comparison of Chapin and Master Manufacturing sprayers.

Choose the Chapin 97254 If
The 97254 fits the buyer whose time at the fill point is the cost that matters. Choose it if one or more of these is you:
- You refill often: a 25 gallon tank cuts the number of trips to the water source.
- Your vehicle’s manual allows the load: about 208 pounds of water alone, plus the tank, pump and wand, as its manual permits.
- You read the exact manual: Chapin’s manual names the 97400E, not the 97254, so follow the manual that comes with your unit.
When I picture the long run along a fence line, the bigger tank is the one I reach for, as long as the vehicle can carry it. Skip it if your rack limit is close to the water weight alone, or if you want a manual that names the exact model.

Safety Before You Spray
A 12V spot sprayer is a pump, a hose and a wand under pressure, and the liquid in the tank can be a pesticide that harms people, pets, bees and water. Every hands-on step in this article points to the shutdown box above, which comes first each time. These notes cover the product label, your gear, the vehicle and the wiring.
What Chapin’s Manual Adds
Chapin’s manual for the 97200E and the 97400E says to always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. It says never to spray flammable, caustic, acidic, chlorine, bleach, petroleum based or other corrosive solutions, or heat, pressure or gas producing chemicals, and to read and follow the chemical manufacturer’s instructions first. It says not to leave the sprayer in the hot sun, because heat can cause pressure build-up, and not to store or leave solution in the tank after use. It also says to flush the pump with water after use and to keep chemicals from sitting in the pump during long idle times.
Read the Label
The product label is the law. It tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftover product and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. Your sprayer’s manual does not replace the label, and the label does not replace the manual: read the label before you open the container, and follow both.
Protective Equipment
Wear the protective clothing and equipment the product label requires, and put it on before you open the container. Wear the eye protection and gloves the label names every time you mix, load, spray, clean the tank or clear a nozzle. Cornell’s pesticide safety program also advises chemical-resistant gloves, goggles and a respirator when you handle moderately toxic products, even when the label does not call for them. Wear every respirator the label requires, of the type the label names, and follow the respirator maker’s instructions for fit, use and care. If you follow Cornell’s advice and wear one the label does not require, or if it is unclear which respirator or filter is right, get qualified guidance on the respirator and filter before you handle the product. Protective equipment lowers your exposure; it does not make spraying safe.
No Rates on This Page
The product label, not this page, gives the amount of product, the dilution and the mixing order, so read it before you mix. Do not combine products unless the mixture complies with every product’s label and its compatibility has been established through the manufacturers or a qualified pesticide specialist; nobody’s advice overrides a label prohibition.
Mixing and Loading
Before you load the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the product label and your manual require for the task. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill or overflow cannot reach a well, a drain or other water. Read the label before you open the container, stand upwind, and do not eat, drink or smoke while you handle pesticides. Never use your mouth to siphon a pesticide from its container. Keep the fill hose above the level of the liquid in the tank so the product cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Use measuring tools kept only for pesticides, never kitchen utensils or food containers. Mix only as much as the job needs so the tank ends empty; do not store leftover mix in the sprayer for later, because it can damage the sprayer’s parts.
Dedicated Sprayer
Illinois Extension advises a dedicated sprayer for the home orchard, one that has never been used for weed control products. Penn State and Iowa State warn that even small amounts of herbicide left in tanks, hoses, screens and fittings can harm crops, and that water alone is generally not enough to remove pesticide residue. Treat a sprayer that has held weed killer as a weed-killer sprayer, and keep a separate one for fruit trees, vegetables, ornamentals and liquid fertilizer.
First Water Test and Pre-Use Check
Before the first water test, complete the full shutdown in the shutdown box, then fill the tank with clean water and close the lid as your manual directs. Connect the power (install the battery or connect the 12V supply) only when you are ready to test. Run the sprayer and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts. Before you open the tank, correct a leak or add product, complete the full shutdown again. Before every use, check the tank, strainer, hose and nozzle, and fix any leak before product goes in. Follow your manual’s first-use steps.
12V Wiring
Before any wiring work on the pump, complete the full shutdown in the shutdown box, including its emergency exception and securing the vehicle. Wire the pump the way your sprayer’s manual says, and use the fuse the manual lists. To disconnect the supply, follow the shutdown box through securing the vehicle, stopping the pump and relieving the pressure, then disconnect it as your manual directs; reconnect it only after the work is complete, every part is secured and the pump switch is off.
Hand Wand on a Vehicle
Montana State University Extension advises not to ride and spray if you have to hold a wand or lance.
ATV and UTV Riding
Wear the helmet and other protective gear the Consumer Product Safety Commission recommends, get hands-on training from a qualified instructor, and sit only in the positions the manufacturer designed for occupants. The CPSC says never to ride with more passengers than there are seats. In a UTV, fasten the seat belts and keep every part of your body inside the vehicle as its manual directs. The CPSC says riders younger than 16 should drive only age-appropriate youth model ATVs, never adult ATVs, and that off-road vehicles are designed for off-road terrain, not paved surfaces. Most ATVs seat one rider.
Load, Surge and Slopes
Stay within the rack and tow capacity in your vehicle’s owner’s manual. Sloshing liquid shifts weight and changes how the vehicle handles: Montana State University Extension advises a spray tank with internal baffles and the lowest practical center of gravity, a boom that works as low to the ground as possible, and a rear-mounted boom or equipment that lowers the operator’s exposure. On an ATV, follow its manual and your hands-on training for body position and for the slopes it permits with a sprayer load; Montana State’s advice for ATVs on a hill is to lean your body uphill, and body position does not guarantee protection against a rollover. In a UTV, stay properly restrained inside the vehicle and follow its manual’s slope limits. Research on ATV injuries has linked uphill travel to backward rollovers.
Pressure and Nozzle
A sprayer’s maximum pressure is the limit of the machine, not a setting to aim for. The product label and the nozzle’s maker decide the pressure and the nozzle for a job. Higher pressure makes more fine droplets that drift, and the nozzle you choose changes the droplet size.
Wind and Drift
Drift is spray carried off target by the air, and wind speed is the factor extension sources stress most. Their figures differ and none fits every situation, and your product label may be stricter than all of them. K-State Extension suggests spraying when the wind is under 10.1 miles per hour and says there is no maximum wind speed that fits every situation. LSU AgCenter says to avoid applying when the wind is above about 10 miles per hour. NC State says under 5 miles per hour when you calibrate with the product in the tank. Cornell gives no number and says not to take a chance by spraying in the wind. Do not spray during a temperature inversion, when cool air near the ground holds small droplets in the air, and do not assume that calm air, early morning or evening is suitable: check the actual conditions and follow every weather restriction on the product label. High temperature and low humidity make spray evaporate faster. Do not spray just before rain. Droplets smaller than about 150 micrometers drift most easily, and higher pressure makes more of them.
Cleaning
Before you clean the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the label and your manual require. Clean the sprayer as soon as you can after use, because dried product is harder to remove than product still in solution. Empty the tank, rinse the tank, hose, wand and nozzle, and clean the strainers and screens, following the product label and your manual; extension guidance warns that water alone may not remove every product. Clean it away from desirable plants, wells and other water, and wash the outside. Do not pour leftover product or rinse water down a sink, a toilet or a storm drain, or onto bare ground.
Container Rinsing and Disposal
Follow the product label’s instructions for rinsing the empty container, handling the rinse water and disposing of the container, and rinse only a container the label directs you to rinse. Add rinse water to a spray mixture only when the label permits it and the mixture can take it without exceeding the permitted fill level or changing the label-directed mixture. Never reuse an empty pesticide container for any purpose. For leftover product, follow the label’s disposal steps, or call your state pesticide agency or a household hazardous waste program.
Storage
Before you store the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception. Store pesticides in their original containers, with the label on, locked up or under the control of a person who can keep others away, and out of the reach of children. Never put a pesticide in a container used for food, drink or household products. Keep pesticides away from food, animal feed and protective equipment, and store pesticides and fertilizers apart, because they can react with each other and start a fire. Store the sprayer drained, cleaned and dry, as your manual describes, with the battery stored as the battery manual describes.
Children, Pets and Others
Keep children, pets and other people out of the area while you mix, load and spray, and keep them off the treated area for as long as the label says. Before you spray, remove toys and take away or cover pet food and water dishes.
Pollinators
Many pesticide labels warn that the product can kill bees and other insect pollinators, and some tell you not to apply while bees are foraging or to notify a beekeeper first. The label’s pollinator wording decides when you may spray around flowering plants; keep spray from drifting onto beehives and flowering plants. Cornell notes that spraying in the early morning or evening can lower the chance that bees are in the area, but do not spray during a temperature inversion and do not assume those times are suitable: check the actual conditions and follow the label’s weather and pollinator restrictions.
If Someone Is Exposed
If someone is exposed to a pesticide, follow the first-aid section of the product label and call Poison Control at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.
Spills
If product spills, keep people and animals away and follow the emergency directions on the product label and its safety data sheet. Try to contain a small spill only if the label says that is safe and you have the protective equipment it requires; when it is safe to do so, complete the shutdown before hands-on work on the sprayer. For a spill you can safely manage, use only absorbents and waste containers that are compatible with the spilled product, as its label, its safety data sheet or qualified emergency guidance specifies, and dispose of the collected waste as directed. If the spill is more than you can manage safely, call the emergency number on the label; call Poison Control at 1-800-222-1222 if anyone is exposed, and call 911 for a fire, immediate danger or a large spill.
A review of the literature on coveralls for agricultural pesticide users found that the real-world effectiveness of protective equipment may be over-estimated (4). Gear lowers your exposure and never makes spraying safe, so I read the label first, every time.
Pick by the Rack Limit First
Open your vehicle’s owner’s manual and find the rack and tow capacity before you compare anything else. If the 25 gallon tank leaves little margin, the 97200E fits and the refills are the price, but when the manual allows the load and you spray often, the 97254 saves stops. Either way, wire it as the manual says, keep the harness clear of pinch points and complete the shutdown before every hands-on step. For my money the Chapin 15 vs 25 gallon sprayer call goes to the 97200E unless refills decide it. If you want more 12 volt models to compare, my roundup of 12 volt ATV spot sprayers lists five picks by tank, pump and hose.
Frequently Asked Questions
Is the Chapin 97254 the same sprayer as the Chapin 97200E apart from tank size?
The Chapin 97254 is a 12 volt ATV and UTV spot sprayer like the 97200E, with the same 1.0 GPM pump rating, 60 PSI maximum and 6 inch opening on a 25 gallon tank. Chapin’s manual names the 97200E and the 97400E but not the 97254, so check hose and wand on your unit.
Does the Chapin 97200E run on a battery?
The Chapin 97200E does not run on a battery of its own: it takes power from a vehicle’s 12 volt supply through a wire harness with an in-line fuse. No battery and no charger come in the product, so the vehicle’s battery and wiring must supply the power, and the manual warns against a pinched or damaged harness.
What maximum pressure does the Chapin 97254 print?
The Chapin 97254 prints a maximum pressure of 60 PSI from its 1.0 GPM diaphragm pump on its listing. That figure is the pump’s ceiling and not a working setting, and the 97400E manual adds that the pump switch shuts the pump off at 60 PSI and that pressure can only be adjusted by adjusting the nozzle.
How do you prime a Chapin 25 gallon sprayer?
You prime a Chapin 25 gallon sprayer by first completing the full shutdown in the shutdown box above, then following the priming steps in the manual for your exact model. Chapin’s 97400E manual floods the intake with water from a garden hose until water starts flowing, which may take up to 15 minutes, and it does not name the 97254.
What warranty does the Chapin 97200E have?
The Chapin 97200E carries a one year warranty, which its manual describes as one year after purchase for the pump, tank and accessories. Chapin’s listing calls it a 1-year limited warranty, and the manual’s cover sends you to Chapin’s website for the warranty details, so read those before you buy.
References
- Proulx R. Spray Equipment and Calibration. AE73. North Dakota State University Extension; revised October 2025.
- Wolf RE. Strategies to Reduce Spray Drift. MF-2444. Kansas State University Agricultural Experiment Station and Cooperative Extension Service; March 2000.
- Brandenburg MA, Brown SJ, Archer P, Brandt EN. All-terrain vehicle crash factors and associated injuries in patients presenting to a regional trauma center. J Trauma. 2007;63(5):994-999.
- Garrigou A, Laurent C, Berthet A, et al. Critical review of the role of PPE in the prevention of risks related to agricultural pesticide use. Saf Sci. 2020;123:104527.
Safety Note: Read your sprayer’s manual and the product label before you open any container. The label is the law: it tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftovers and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. This page never gives an amount of product, a dilution or a mixing order: the label does. Wear the protective clothing and equipment the label requires, put it on before you open the container, and wear the eye protection and gloves it names whenever you mix, load, spray, clean the tank or clear a nozzle. Protective equipment lowers your exposure; it does not make spraying safe. Wear every respirator the label requires, of the type it names, and follow the respirator maker’s fit, use and care instructions. Before you clean or store the sprayer, or wire a 12V pump, complete the shutdown below first. Before you mix or load, complete the shutdown below, including its emergency exception. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill cannot reach a well, a drain or other water. Stand upwind, never use your mouth to siphon a product, keep the fill hose above the liquid so it cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Mix only what the job needs, and do not store leftover mix in the sprayer. Never point the wand at yourself, another person or a pet, and never test a spray against your hand. Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Otherwise, before you open the tank, fill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, load, unload, transport, store or leave the sprayer, or lift, put on or take off a backpack unit, complete the shutdown. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Battery sprayer: release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery. 12V vehicle sprayer: first stop and secure the vehicle as its manual directs, then release the trigger, close the wand or boom valve and switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies, and reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the label’s protective equipment while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual, never with your mouth and never by blowing into it. Refit every part and check for leaks with clean water before product goes back in. For the first water test, complete the shutdown first, fill the tank with clean water and close it as your manual directs, connect the power only when you are ready, and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts; complete the shutdown again before you open the tank, fix a leak or add product. Wind, heat and fine droplets carry spray off target: the label may be stricter than any extension guideline, and extension sources give different wind figures, so no single number fits every situation. Do not spray during a temperature inversion, and do not assume that calm air, early morning or evening is suitable. Do not spray just before rain. Keep children, pets and other people out of the area while you spray and off the treated area for as long as the label says, and remove toys and cover pet food and water dishes first. The label’s pollinator wording decides when you may spray around flowering plants, and early morning or evening is not automatically suitable. A sprayer that has held weed killer should stay a weed-killer sprayer: extension services advise a dedicated sprayer, and rinsing may not remove every residue. Follow the product label’s instructions for rinsing empty containers, handling rinse water and disposing of them, and never reuse an empty pesticide container; for leftover product, call your state pesticide agency or a household hazardous waste program, and never pour it down a sink, a toilet or a storm drain. Store pesticides in their original containers, locked up and out of the reach of children, away from food and animal feed, and keep pesticides and fertilizers apart. If someone is exposed, follow the first-aid section of the label, call Poison Control at 1-800-222-1222 and keep the label with you; call 911 in an emergency. If product spills, keep people and animals away and follow the label’s emergency directions; try to contain a small spill only if the label says that is safe and you have the protective equipment it requires, and otherwise get help (the emergency number on the label, Poison Control if anyone is exposed, 911 for a fire, immediate danger or a large spill). Use only the battery and charger the maker supplies or lists for your exact sprayer, charge and store the battery as your manual describes, and do not use a damaged battery or charger: lithium-ion batteries can overheat and catch fire. Wire a 12V pump the way your manual says and use the fuse it lists. On an ATV or UTV, wear the helmet and protective gear the Consumer Product Safety Commission recommends, get hands-on training, sit only in the positions the manufacturer designed, never ride with more passengers than there are seats, and in a UTV fasten the seat belts and keep every part of your body inside the vehicle; stay within the rack and tow capacity in your vehicle’s owner’s manual, and remember that sloshing liquid shifts weight and changes how the vehicle handles; Montana State University Extension advises against riding and spraying if you have to hold a wand or lance. Stop at once, complete the full shutdown and inspect if the sprayer leaks, loses pressure or runs without spraying, and restart only as the manual allows. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, do not handle or remove it: keep people away, follow the battery manual’s emergency instructions, and if it smokes or burns, move away and call 911 or the fire department. Before you fill the tank, complete the shutdown, and fill it only to the level your manual allows. Carrying a full tank is tiring: rest when you are tired.


