Five quick-connect pressure washer nozzle tips arranged on a concrete surface beside an electric pressure washer

Pressure Washer Nozzle Colors Explained: What Each Maker Prints

Pressure washer nozzle colors are each maker’s own code, so a color tells you what a tip is only through the table in your manual. Simpson’s nozzle guide prints red, yellow, green and white for the 0, 15, 25 and 40 degree tips with black for soap, Craftsman prints orange for its 15 degree tip, and Generac names its tips Blast, Clean and Wash.

In large-scale production, I checked sprayer nozzle output with calibration cylinders, so I treat a nozzle as a part with a job, never as a color. Below is what each maker prints, how the soap and turbo tips differ, and how to read your own table.

Pressure Washer Nozzle Colors Have No Single Standard Code

A nozzle color is a label that a maker puts on a tip. It is no industry standard, and the manuals compared below show it: the same angle wears different colors in different tables, and black marks the soap tip in some tables and the turbo nozzle in another.

Match the color to the degree or the name in your own manual, never to a chart from another maker. A degree is the width of the spray fan, and the manuals list tips such as 15, 25 and 40 degrees, plus a turbo nozzle that makers describe as a circular pattern. Your manual’s nozzle table decides what each tip is called, what the maker says it is for and which tips came in your box. The way the pump, hose and gun feed the nozzle is laid out in my guide to how a pressure washer works.

Read the pressure washer’s manual before you connect water or power, and follow it. Its warnings, its operator rules and its steps for your exact model come before anything in this article.

Every step in this article that puts a hand near a nozzle, a hose fitting or the spray gun comes after the box below. I recommend reading it once now, because the later sections point back to it instead of repeating it.

Stop and Make Safe First

Stop and make safe before you connect or disconnect a hose, change a nozzle, wand or accessory, clear a clogged nozzle, clean a filter, add detergent, refuel, check the oil, drain the washer, move it, store it or leave it. Release the trigger and engage the trigger lock on the spray gun. Gas washer: turn the engine off with its switch as the manual says and wait until all moving parts have stopped. Let the engine and the muffler cool for the time your manual gives before you refuel, store the washer or touch hot parts, and disconnect the spark plug wire before maintenance where your manual directs it. Corded electric washer: turn the washer off with its power switch and wait until all moving parts have stopped. Every washer, after the steps above for your type: follow your manual’s water-supply shutdown and pressure-relief procedure. Point the gun away from people, pets and electrical equipment at a discharge location your manual and the detergent label permit. Disengage the trigger lock, squeeze the trigger to relieve the trapped pressure as the manual directs, then engage the lock again. Then unplug a corded washer by the plug, not by the cord, with dry hands. Do not disconnect hoses or change nozzles before the pressure is relieved. If the manual’s procedure does not release the pressure, stop and get service; do not loosen a fitting to release it. Only then disconnect hoses or change nozzles. Where your manual gives a different order for these steps, follow your manual’s order. Follow every applicable step in your manual, in the order it specifies, and check that every hose, fitting and nozzle is attached and undamaged before water or power goes back on.

What a Nozzle Color Stands For

A color on a tip can stand for a spray angle, a job or a trade name, and which one it is depends on the maker. The same three labels sit on every tip in different mixes.

Color, Degree and Name Are Three Labels

A fan nozzle sprays a flat fan at a fixed angle. A technical brief from EPA’s research office, written for decontaminating hard urban surfaces, describes fan nozzles with fixed spray angles of 0, 15, 20 or 40 degrees. The manuals in this article print 25 where that brief names 20, which shows that the angle set belongs to the maker and the model. My answer to “what is a fan spray nozzle” covers the pattern, the angle and the droplet size.

The color is the maker’s shorthand laid over the angle. One maker paints its 25 degree tip green, another names a green tip Clean, and a third lists a tip only by its degree.

Why the Degree Is the Label to Match

Where a manual prints both a color and a degree, the degree describes the spray and the color marks the tip. A manual that prints only a name, as Generac does for its Blast, Clean and Wash tips, that name and the manual’s own description of it are the label.

On the drip irrigation I built for the orchard, I read the size printed on a fitting before I connect it, and I treat the degree printed in a nozzle table the same way.

The Code Westinghouse and Simpson Print

Two makers print the code most readers expect to see: red, yellow, green, white and black. Even here, I recommend taking the pairing from the table in your own manual.

Simpson’s Nozzle Guide

Simpson’s own nozzle guide lists the tips in one short run.

  • Red: 0 degrees.
  • Yellow: 15 degrees.
  • Green: 25 degrees.
  • White: 40 degrees.
  • Black: the soap nozzle.

The guide adds that cleaning solutions cannot be applied with the red, yellow, green or white tips. That line explains why the soap tip is a separate part and not a setting of the other four.

Westinghouse Pressure Washer Nozzle Colors

The Westinghouse manual for the WPX3200 and WPX3400 gas washers lists five quick-connect nozzles at 0, 15, 25 and 40 degrees plus a soap nozzle. Its nozzle table names the colors red, yellow, green and white, with soap as the black one. According to Westinghouse, detergent is drawn through the pump only when the black detergent nozzle is attached to the end of the spray lance. That gas washer has its own page, my review of the Westinghouse WPX3200, with the soap tank in detail.

The manual covers the WPX2700, WPX3200 and WPX3400 in one booklet, so the table in the booklet is the one to read for the pairing of each color and angle on your washer.

Where Other Makers Differ

The red, yellow, green, white and black code is not universal. The table lists what each maker or manual below prints for its own tips, in the maker’s words.

Nozzle labels as each maker prints them
Maker and model Tips as listed Colors as printed
Simpson, nozzle guide 0, 15, 25 and 40 degrees, soap Red, yellow, green, white, black soap
Westinghouse WPX3200 and WPX3400, gas 0, 15, 25 and 40 degrees, soap Red, yellow, green, white; soap is black
Craftsman CMEPW1900 and CMEPW2100, corded 15, 25 and 40 degrees, soap, turbo 15 orange, 25 green, 40 white, turbo black
Greenworks GPW3002A, corded 15, 25 and 40 degrees, soap, turbo 15 yellow, 25 green, 40 white, soap black
Greenworks GPW2003, corded 25 and 40 degrees, soap, turbo 25 green, 40 white, soap black
Ryobi RY141612, corded 15 degrees, turbo, soap Soap listed as blue or black
Kärcher K1700 Cube, corded 15 degrees, turbo, soap Not listed
Generac, support page Blast, Clean, Wash, Detergent Red, green, white, black

Craftsman Pressure Washer Nozzle Colors and Greenworks

The Craftsman manual for the CMEPW1900 and CMEPW2100 lists five nozzles in its table: a 15 degree orange tip, a 25 degree green tip, a 40 degree white tip, a soap tip and a black turbo nozzle. Check which of them came in your box, because the table can list more tips than a kit holds. I went through the corded 2100 PSI model and its manual in my review of the CRAFTSMAN CMEPW2100.

The Greenworks GPW3002A manual lists a yellow 15 degree narrow fan tip, a green 25 degree narrow fan tip, a white 40 degree wide fan tip, a black soap spray tip and a turbo nozzle. The GPW2003 manual lists a green 25 degree narrow fan tip, a white 40 degree wide fan tip, a black soap tip and a turbo nozzle, so a 15 degree tip is not in its table. The color of the 15 degree tip alone differs between Craftsman and Greenworks: orange in one table, yellow in the other.

Ryobi Pressure Washer Nozzle Colors, Kärcher and Generac

The Ryobi RY141612 manual lists a 15 degree nozzle, a turbo nozzle and a soap nozzle, and its nozzle selection guide uses blue or black for the soap nozzle. The listing photo of its nozzle storage shows an orange 15 degree tip and a blue soap tip. The Kärcher K1700 Cube manual lists a turbo nozzle, a 15 degree nozzle and a soap nozzle by name and angle. I examine this 1600 PSI corded model in my review of the Ryobi RY141612.

Generac’s support page names a Blast nozzle in red, a Clean nozzle in green, a Wash nozzle in white and a Detergent nozzle in black, and it gives no degrees. It points the reader to the owner’s manual for the description of each nozzle that came with the washer. I read a table like this one maker at a time, and I never copy one maker’s pairing onto another maker’s tips.

Three patterns hold in these manuals and no further. Green marks the 25 degree tip in Simpson’s guide, the Craftsman manual and both Greenworks manuals. White marks the 40 degree tip in the same four. Black marks the soap tip in the Westinghouse, Greenworks and Simpson tables, while Craftsman lists black for its turbo nozzle. I gave my verdict on one of the Westinghouse gas washers behind that table in my review of the Westinghouse WPX3400.

The Soap Nozzle and the Turbo Nozzle

Two tips behave differently from the fan tips, and they cause most of the confusion at the nozzle table. One is for detergent and the other is a spinning tip, and each maker words both in its own way.

The Soap Nozzle

Before you add detergent or connect or adjust a detergent accessory, complete the applicable stop and make-safe steps in the safe-state box. Use only the detergents your manual allows, through the detergent system the manual describes, and read the detergent label before you open it. Wear the protective equipment the detergent label requires, and avoid contact of detergent with your eyes and skin. Do not run a detergent that your manual does not name through the pump.

The manuals agree that detergent travels through the soap tip and at low pressure. Kärcher says detergents can only be applied at low pressure and, to rinse, says to replace the soap nozzle with the 15 degree nozzle. Greenworks says soap goes only through the black soap tip at low pressure. Ryobi says that using the soap nozzle activates its soap injector, and it prints in capitals that you use only detergents designed for pressure washers. The foot-pedal Kärcher has its own page in my review of the K1700 Cube.

I read a detergent label before I open a container, a habit from my plant protection training. A soap tip that is the wrong color on a table is still the soap tip, and the manual’s wording about detergent matters more than the paint on the plastic.

The Turbo Nozzle

A turbo nozzle is described in the manuals as a circular spray pattern, and the makers word the angle differently. Greenworks says the turbo nozzle of the GPW3002A rotates in a zero-to-15-degree spray pattern, and its GPW2003 manual calls it a zero to 15 degree circular pattern. Kärcher describes the K1700 Cube turbo nozzle as a zero degree circular pattern. Craftsman lists its turbo nozzle in black. I cover the GPW3002A in my Greenworks pressure washer review.

Those descriptions do not match, so a turbo nozzle gets no angle from me. I recommend reading the maker’s own sentence for your model and fitting the tip only as that manual says.

How to Read Your Own Pressure Washer Nozzle Color Chart

Your manual’s table is the only chart that counts for your washer. These six steps take a few minutes with the manual open next to the nozzles.

  1. Find the nozzle table in the manual for your exact model, using the model name on the washer’s label.
  2. Read the name, the degree and the color of every tip, and write the pairs down as the manual prints them.
  3. Count the tips in your box against the table, because a manual can list tips that your kit does not include.
  4. Find the soap tip, and note that detergent goes only through it.
  5. Read what the manual says each tip is for, and follow it. Your manual names the nozzle for the job.
  6. Store the tips where the manual says to keep them, with the soap tip easy to tell from the rest, and handle them only after the stop and make-safe steps in the safe-state box above.

Check both your washer’s manual and the care instructions of the surface or finish maker before you wash, and follow their restrictions. If they prohibit pressure washing, do not use a different nozzle or setting as a workaround. I leave surface advice to those two documents for a plain reason: no nozzle color chart can know what your surface can take.

Safety Before You Spray

The tips in this article are parts of a machine that sprays water at a pressure that can wound. The next lines apply to every washer in the table, and I recommend them as a card to keep near the machine.

  • Spray and wounds: Never point the spray at yourself, another person, a pet or any part of the body. Keep your hands and feet away from the nozzle and the stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. CDC says the strong spray can cause serious wounds that might first appear minor, and a case report describes how this kind of injury can lead to infection and compartment syndrome and, in some cases, amputation (1). Another report describes a finger injury from a washer at a car wash that needed surgery to relieve the pressure inside the finger (2). A review of the medical literature found that the site of the injury and the material injected changed the risk of amputation (3).
  • Protective equipment: Wear safety glasses or goggles and closed footwear when you operate the washer, and put them on before you start; where your manual requires goggles, side shields or a face shield, that requirement replaces the minimum here. Follow the manual’s additional protective-equipment requirements, including hearing protection where the manual requires it, and the detergent label’s requirements when you handle detergent. Keep your hands and feet away from the spray. Protective equipment does not make contact with the stream safe. A case series of three people hurt by pressure washers describes eye injuries that all needed surgery and ended with poor final vision (4).
  • Trigger lock: Engage the trigger lock on the spray gun whenever you stop spraying, even for a moment, before you set the gun down, and before you walk away or change position. Disengage the lock only for controlled spraying or for the manual’s pressure-relief procedure, with the gun pointed in a safe direction.
  • Hands, footing and kickback: Hold and brace the spray gun as your manual instructs, keep firm footing on a surface that is not slippery, and follow your manual’s warning about the push of the gun when you squeeze the trigger. Start the stream away from your feet and from anyone else, and never swing the gun toward people or pets as you turn.
  • Children and pets: Keep children, pets and other people away from the work area while the machine runs, and never let a child use the machine. Store the washer and its fuel where children cannot reach them.
  • Height: Do not use a pressure washer for a task at height, such as from a ladder, unless your manual expressly permits the equipment and the method.

Operate a gas pressure washer outdoors, never inside a building or a partly enclosed space. CDC says to keep it at least 20 feet from any window, door or vent, and your manual may set a stricter placement, which you follow. Engine exhaust contains carbon monoxide, which you cannot see or smell and which can kill. Opening a door or a window does not make it safe to run an engine inside. If anyone develops symptoms such as headache, dizziness, weakness, nausea or confusion, move to fresh air and get emergency medical care.

Before you refuel, complete the applicable stop and make-safe steps in the safe-state box, including letting the engine cool as the manual directs. Add only the fuel and oil the manual names, keep fuel away from flame and sparks, and wipe up spilled fuel before you start the engine. The engine and the muffler stay hot after the engine stops, so keep your hands, skin and clothing away from them.

Use the electrical supply and the GFCI protection your manual specifies, and test the GFCI before use according to its instructions. If the washer trips a GFCI or a circuit breaker while you use it, stop using it and have a qualified repair person examine it before you use it again; do not keep resetting it and carry on. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Never cut or splice a power cord or an extension cord.

Wear closed, rubber-soled footwear that gives some electrical insulation, plus any additional footwear the manual requires; footwear does not replace GFCI protection or the other electrical precautions. Use an extension cord only if your manual permits it, and then only the type and length it names. Keep every plug and cord connection dry, out of standing water and away from runoff and the area you are washing, and keep the spray away from outlets, wiring and electrical equipment. Do not use a damaged cord or plug.

The warning behind these lines comes from a 1983 release of the Consumer Product Safety Commission about fatal electric shock from electric washers.

If someone is hit by the stream, get medical care without delay, even if the wound looks small. If a cleaning product is swallowed or gets in the eyes, follow the label’s first-aid section and call Poison Control (America’s Poison Centers) at 1-800-222-1222. Call 911 for a fire or immediate danger.

Changing a Nozzle Safely

Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. A nozzle change puts your hand at the end of the lance, and the quick-connect collar is built to release a tip with a pull.

  1. Complete the stop and make-safe steps in the safe-state box above, including the pressure relief your manual describes.
  2. Pull back the quick-connect collar at the end of the spray lance. Westinghouse words the next two moves as insert the nozzle, then release the collar.
  3. Pull on the nozzle to be sure it is secured. Westinghouse says to do this, and Kärcher says to check to make sure the nozzle is secure.
  4. Keep the nozzle pointed away from your face and from other people at all times, and keep it away from anyone in the work area.
  5. Check that every hose, fitting and nozzle is attached and undamaged before water or power goes back on.

The Ryobi RY141612 manual adds a warning for its own quick-connect: the quick-connect feature contains small springs that could eject the nozzle with some force. Ryobi also says never to remove nozzles without first turning off the motor, disconnecting the power supply, relieving the water pressure in the trigger handle and locking the lock out on the trigger handle. I recommend laying the tips out in the manual’s order before the first change, so that your hand never hunts for the right one with the lance in the other.

Use only the nozzles and accessories your manual permits, following its instructions for the job. Never direct any nozzle at skin, people or animals. Before you change a nozzle, complete the stop and make-safe steps in the safe-state box.

A nozzle that gives a weak, uneven or pulsing stream may be blocked. Complete the stop and make-safe steps in the safe-state box, then clear the nozzle only with the tool and the method your manual describes. Never look into the nozzle or point it at anyone to check it. Ryobi says a pulsing sensation felt while squeezing the trigger may be the result of a clogged or dirty nozzle, and it names a straightened paper clip or a fine needle for clearing. Westinghouse supplies a nozzle cleaning tool in the carton. The two makers name different tools, so the tool your manual names is the one to use.

Match Every Tip to Your Own Manual

The most useful minute with a new washer goes into a card. For each tip in your exact model’s table, write its name, its degree, its color and whether the manual calls it the soap tip, as the manual prints them. Add a line for any tip the table lists that your kit does not include, so that the card matches what is in your hand. I walk through a full session in my guide to using a pressure washer, in the order the manuals give.

Keep the card with the manual, and fit a tip only after the stop and make-safe steps in the safe-state box. I recommend the card because it records only what your manual says. Treat pressure washer nozzle colors as a label that your own manual defines.

Frequently Asked Questions

What do pressure washer nozzle colors mean?

Pressure washer nozzle colors are each maker’s marking for a tip, and the table in your manual says which spray angle or job each color stands for. Simpson’s guide pairs red with 0 degrees, yellow with 15, green with 25 and white with 40, with black for soap, while Craftsman marks its 15 degree tip orange. Take the meaning from your own manual and not from another maker’s chart.

Are pressure washer nozzle colors the same on every brand?

Pressure washer nozzle colors differ between brands. Green marks the 25 degree tip in Simpson’s guide, the Craftsman manual and both Greenworks manuals, but the 15 degree tip is yellow for Simpson and the Greenworks GPW3002A and orange for Craftsman, and Generac names its tips by job with no degrees.

What color is the soap nozzle on a pressure washer?

The soap nozzle on a pressure washer is black in the Westinghouse, Greenworks GPW3002A and GPW2003 manuals and in Simpson’s guide, and Generac’s black tip is its Detergent nozzle. Ryobi’s manual marks its soap nozzle blue or black. Whatever the color, detergent goes only through the soap tip, at low pressure, as your manual describes.

What is a turbo nozzle on a pressure washer?

A turbo nozzle on a pressure washer is a tip that makers describe as a circular spray pattern, and each maker words it differently. Greenworks says the GPW3002A turbo nozzle rotates in a zero-to-15-degree spray pattern, and Kärcher describes the K1700 Cube turbo nozzle as a zero degree circular pattern. Read the description in your manual, and complete the stop and make-safe steps in the safe-state box above before you fit it.

Do electric pressure washer nozzle colors differ from gas ones?

Electric pressure washer nozzle colors differ from gas ones by maker and not by power type. The corded Greenworks GPW3002A lists yellow 15, green 25, white 40 and black soap tips, which matches the code Simpson prints, while the corded Craftsman marks its 15 degree tip orange. Check the table for your own model.

References

  1. Funato N, Sugizaki Y, Ri Y, Ichibayashi R. High-pressure injection damage caused by a high-pressure washer. Cureus. 2024;16(1):e52498. doi:10.7759/cureus.52498
  2. Choi JH, Choi SY, Hwang JH, Kim KS, Lee SY. Finger compartment syndrome due to a high-pressure washer injury: a case report. World J Clin Cases. 2023;11(13):3017-3021. doi:10.12998/wjcc.v11.i13.3017
  3. Hogan CJ, Ruland RT. High-pressure injection injuries to the upper extremity: a review of the literature. J Orthop Trauma. 2006;20(7):503-511. doi:10.1097/00005131-200608000-00010
  4. Placide J, Yang MY, Gross AW, Crowell EL. Case series: traumatic ocular lacerations secondary to pressure washers. Am J Ophthalmol Case Rep. 2022;27:101612. doi:10.1016/j.ajoc.2022.101612

Safety Note: Read your pressure washer’s manual before you connect water or power, and follow it. Never point the spray at yourself, another person, a pet or any part of the body. Keep hands and feet away from the nozzle and stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. Wear safety glasses or goggles and closed footwear before operating the washer, plus any additional protection required by the manual and the detergent label. Follow the manual’s instructions for the trigger lock, grip, footing and recoil, and engage the trigger lock whenever you stop spraying. Use only the nozzles, accessories and detergents the manual permits, and never point any nozzle at skin, people or animals. Do not perform a task at height without instructions expressly permitting the equipment and method in the exact manual. Gas models: operate outdoors, never inside a building or a partly enclosed space. Keep the engine at least 20 feet from any window, door or vent, following CDC’s pressure washer guidance and any stricter manual requirement. Exhaust contains carbon monoxide, which cannot be seen or smelled and can kill. Opening doors or windows does not make indoor operation safe. Refuel only with the engine off and cool, following the manual. Corded models: use the manual’s specified electrical supply and GFCI protection, and test the GFCI before use according to its instructions. After an operating GFCI or breaker trip, do not reuse the washer until a qualified repair person has examined it. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Wear closed, rubber-soled footwear that provides some electrical insulation, plus any additional footwear required by the manual; footwear does not replace GFCI protection or the other electrical precautions. Never cut or splice cords. Use an extension cord only as the manual permits. Keep connections dry and away from runoff, standing water and the washing area, and keep spray away from electrical equipment. Battery models: use only the battery and charger the maker specifies for your exact model. Emergency first: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Otherwise, complete the applicable stop and make-safe procedure before hose, nozzle, wand or accessory work, clearing a blockage, cleaning, maintenance, refueling, checking oil, adding detergent, battery changes or charging, draining, moving, transporting, storing or leaving the washer. Follow your exact manual’s procedure and order. Release the trigger and engage its lock. Gas: switch the engine off and wait for it to stop; disconnect the spark plug wire before service as the manual directs, and let hot parts cool before refueling, storage or contact. Corded: switch off and unplug by the plug with dry hands. Battery: switch off, remove a removable battery as the manual directs and keep it away while working; for a built-in battery, follow the manual’s isolation procedure and do not open the battery compartment. Complete the manual’s water-supply shutdown and pressure-relief steps: point the gun in a safe direction at a permitted discharge location, disengage the trigger lock, squeeze the trigger as directed to relieve pressure, then reengage the lock. Do not disconnect hoses or change nozzles until pressure is relieved. If pressure cannot be relieved by the prescribed procedure, obtain service without loosening fittings. Refit and inspect parts before restoring water or power. Replace a damaged high-pressure hose; never repair or patch it. Before you wash, plan how to keep wash water, detergent and debris out of streets, storm drains, ditches and streams, and check with your city or county stormwater office about collection and disposal. Send wash water to landscaping only where local rules and the detergent label permit it and the soil can absorb it without runoff or contamination. Keep children and pets away, and never let a child use the machine. Drain and store the washer as its manual directs. For exposure to a cleaning product, follow the label’s first-aid instructions and call Poison Control at 1-800-222-1222. Call 911 for a fire or immediate danger.

Scroll to Top