The 4-inch vs 6-inch auger bit choice comes down to what has to stand in the hole: a 6-inch bit makes a hole with 2.25 times the area of a 4-inch bit, and that gap decides whether a 4×4 post fits. I measure the post before I look at any bit. Below I show the arithmetic, what makers print for their bit sizes, and how to change a bit safely.
4-Inch vs 6-Inch Auger Bit: The Short Answer
A bit’s diameter is the width of the hole it makes, so the choice is really a choice of hole width. The 4-inch bit suits small stakes, small plants and light posts. The 6-inch bit is for when a 4×4 post has to stand in the hole with room around it. A 4-inch hole is narrower than the diagonal of a 4×4 post, and the diagonal is what has to clear.
Bit size does not change how deep a machine may dig. Makers print a maximum depth for the machine and name the bit it applies to, and that figure is a ceiling, never a promise for hard clay or rock. My answer to “what is an earth auger” lays out the parts, types and uses of the machines.
| Question | 4-inch bit | 6-inch bit |
|---|---|---|
| Hole width | 4 inches | 6 inches |
| Area across the hole | about 12.6 square inches | about 28.3 square inches |
| Soil lifted per foot of depth | about 151 cubic inches | about 339 cubic inches |
| Clears a 4×4 post | No, the post diagonal is wider | Geometrically yes, with about half an inch at the corners for a post that measures 3.5 inches a face |
| Suits | Stakes, light posts, small plants | Stakes, posts that clear it, small plants |
The figures in the table are plain geometry for a straight-sided hole. Real holes vary with soil and with how the bit’s flighting lifts the spoil, so treat them as a way to compare the two sizes, not as a promise about any one hole.
How an Auger Bit Is Measured
Auger bit diameter is the diameter of the hole, and bit length is a separate number. A bit of 8 inches by 36 inches, for example, makes an 8-inch hole, but its 36-inch length is not the depth the machine will reach. Earthquake lists its E43 combo that way on its own page, and I cover that kit in my Earthquake E43 gas auger review.
Diameter Is the Hole
Makers print the diameter as the hole the bit makes. The Ryobi RY40701 manual, for one, names its bit and hole diameter as one figure. The EGO EG0800E manual (Australia and New Zealand edition) prints its bits in millimeters: 100, 150, 200 and 250 millimeters, which come to roughly 4, 6, 8 and 10 inches.
Length Is Not Depth
Depth is the machine’s own printed maximum, and the maker names the bit that figure belongs to. I read that line in the manual before I buy a bit, because a long bit on a machine does not extend what the maker allows.
What a 4-Inch Auger Bit Is Good For
The 4-inch size is the small end of what makers sell, and it earns its place on jobs that need a narrow hole. A tree stake, a drip line header post or a small plant plug are the kind of jobs it fits. A 4 inch earth auger bit leaves little room around anything wider than a few inches. I also cover the 8-inch size in my 8 inch vs 10 inch auger bit guide for readers who want a wider hole.
Small Plants and Stakes
Planting guidance gives the width in multiples of the root ball. Colorado State University Extension says three times the root ball diameter. The University of Maryland Extension says at least twice as wide, and Illinois Extension says two to three times. By that arithmetic a 4-inch hole matches a root ball of roughly 1.3 to 2 inches across, which is a seedling or a plug, not a nursery tree. My roundup of auger picks for planting trees covers gas and battery machines for tree holes.
Those extension pages describe planting holes in general, and an auger hole is not shown to suit a tree. Colorado State also asks for a saucer-shaped hole and Maryland for sloped sides, while an auger cuts straight sides. Depth is the part a bit cannot fix: in one study, Yoshino cherries planted 15 or 31 centimeters below grade lost half the trees within two years, while every tree planted at grade lived (1). For depth, Colorado State asks for a hole one to two inches shallower than the root ball, while Maryland and Illinois say no deeper than the root ball.
Light Posts
A 4 inch post hole auger bit works for a post whose widest dimension is clearly under 4 inches, such as a thin stake or round pole. I measure the widest point of the post, which for a square post is the diagonal, and compare that number with the hole. If the post measures more than 4 inches corner to corner, move up a size. My roundup of auger picks for fence posts covers gas, corded and battery machines for that job.
What a 6-Inch Auger Bit Is Good For
The 6-inch size is where a common square post starts to fit. It is still the small side of what makers build around, since gas kits such as the Champion 201092 ship an 8-inch bit.
The 4×4 Post Worked Example
A square post is widest across its corners. The diagonal is about 1.41 times the width of a face. Suppose your 4×4 measures 3.5 inches on a face, as finished 4×4 posts commonly do, but check yours with a tape. The diagonal is then 3.5 times 1.41, which is about 4.95 inches, and I write that number down before I think about a bit. My roundup of auger picks for 4×4 posts covers machines for single post holes.
A 4-inch hole cannot take that post. A 6-inch hole leaves (6 minus 4.95) divided by 2, about half an inch, at each corner, and about 1.25 inches at the middle of each face. A 6 inch post hole auger bit is therefore the smaller of these two sizes that clears the post, though the hole and footing dimensions your fence plan needs are a separate check. A 6×6 post with a 5.5-inch face has a diagonal near 7.8 inches, so it needs more than a 6-inch hole.
No table pairs post size with bit size, and this is geometry, not a code rule. Concrete, gravel, footing size and frost depth are separate questions that local rules answer. If you are still choosing between a machine and a hand tool, my guide comparing an auger and post hole digger covers fence, deck and planting jobs.
Two People at Six Inches
Echo’s 2005 operator’s manual for its EA-400 and EA-500 gas earth augers says that drilling holes six inches in diameter or larger may be easier if two people hold the handles on opposite sides. Use the number of people your exact manual specifies, because a 6 inch earth auger bit is not a one-person or two-person rating by itself.
The Numbers Side by Side
I find that the area ratio explains why the next size up feels like a big step. Hole area grows with the square of the diameter, so a 6-inch bit does 2.25 times the area of a 4-inch bit, not 1.5 times.
| Measure | 4-inch hole | 6-inch hole |
|---|---|---|
| Area (pi times radius squared) | 12.57 square inches | 28.27 square inches |
| Per foot of depth | 150.8 cubic inches | 339.3 cubic inches |
| Per foot of depth, in cubic feet | 0.087 | 0.196 |
| Post diagonal it clears | under 4 inches | up to about 6 inches, less any gap you want |
| Root ball width at two to three times | about 1.3 to 2 inches | about 2 to 3 inches |
More soil to lift is a fact about the hole, not about any machine: dig speed, torque and time per hole depend on the machine and the soil, so I give no figure for them. My answer to “how does an earth auger work” explains the power head, the bit and the torque.
What Machine Makers Print for Bit Sizes
Makers print their bit sizes in different units and in different sets, and none of them pairs a bit size with a post size.
- Echo: the EA-400 and EA-500 manual (2005 edition) lists 6, 8 and 10 inch earth augers, with extensions for deeper holes.
- Ryobi: the bit sheet for the RY40701 and P2903 lists 4, 6, 8 and 10 inch bits, and the RY40701 ships with an 8-inch bit.
- EGO: the EG0800E (Australia and New Zealand edition) takes bits of 100, 150, 200 and 250 millimeters, plus a 500 millimeter extension.
- Gas kits: the Champion 201092 and 200940, Powermate PEA438.1, Earthquake E43 and VEVOR D43-F ship with an 8-inch bit, so a 4-inch or 6-inch bit may be a separate purchase.
The pattern is that 8 inches is the working size for many kits, and the 4-inch and 6-inch bits sit at the small end. A bit also has to match the head. Ryobi’s bit sheet names the two machines it fits, and the Ryobi RY40701 and EGO EG0800E each use a locking pin with a clip, while Champion uses a clevis pin. Read your own manual for the bit your head takes. For bigger holes, my comparison of 8 inch with 12 inch auger bits covers the larger sizes.
Soil Limits Are Printed, but Only by Some
The Makita DG001G ties its capacity to the soil: 60 millimeters on high speed, 200 millimeters at low speed in sandy soil and 150 millimeters in clay. That is one maker’s limit for one small tool on named soils. Never read a diameter as a promise about clay or rock.
Does a Bigger Bit Change the Work on the Machine?
A wider bit does not change the printed depth, but any bit can bind, and a bind is when the machine fights back. A bind can happen with either size, so the same precautions apply to both.
Binding and Torque Reaction
Echo’s EA-400 and EA-500 manual warns that the auger may twist suddenly and forcefully if it contacts large rocks, roots or other hidden obstacles. The EGO EG0800E manual tells the operator to stay alert to the torque reaction force. In a laboratory simulation of tool torque reaction on a handle, wrist muscle activity was very high even though the torque pulses were short and the peaks low (2). That study used a simulated handle, not an auger, but it shows why a sudden twist loads the wrists and forearms.
Reaction loads from handheld powered tools have also been linked to physiological changes in assembly workers using tightening tools (3). Those workers used a different tool, so I cite the review only for the general point that handles transmit twist to the body.
If the Bit Binds
If the bit hits a root, a rock or a buried object, it can bind and the machine can twist or kick. Keep firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. Release the throttle or trigger immediately if the bit binds or control is threatened, then complete the full shutdown in the shutdown box below and inspect for damage before restarting. Use reverse only where your manual authorizes it for your model.
If the Bit Sticks
If the bit sticks in the hole or material wraps around it, do not force it and do not reach for the bit. Stop and complete the full shutdown in the shutdown box below before touching or inspecting it. Use only the freeing or clearing method specified in your exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when your manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. If your manual gives no procedure, obtain manufacturer or qualified service guidance.
People Near the Work
People Near the Work
Keep children, pets and other people out of the work area and at least the distance specified in your exact manual. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs, and stop if anyone approaches. No distance makes a work area safe on its own: keep watching it. On a two-person unit, the second person is the operator’s helper only as your manual describes.
Use the number of people your exact manual specifies. A two-person unit needs a second person who knows the plan, holds the unit as the manual describes and stays clear of the bit, and both people stop when either calls a stop. A one-person unit is operated by one person; never add a helper to a hand-held unit unless the manual says so. My one-person vs two-person earth auger guide explains what makers print about crew size.
Digging with an auger is heavy, jarring work that twists your arms and back. Take breaks, stop when you are tired or your attention slips, and use the gloves your manual recommends.
Changing the Bit Safely
Changing a bit puts hands next to a sharp steel flight that is connected to a motor or an engine, so complete the full shutdown in the shutdown box below before you change a bit. EGO also says to wear protective gloves when doing maintenance on the bit, which is very sharp, and that applies when the machine is off and its power source is removed, never near a turning bit.
Shutdown Box
Shutdown before you clear or free the bit, change or attach the bit, free a stuck bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger. Never reach toward the bit while it turns, and never clear it or free it with the machine running. Corded electric auger: release the switch or trigger, wait until the bit has stopped completely, then unplug the auger from the outlet by the plug, not the cord. Before transport or storage, also let the motor cool. Battery auger: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where your model has one, and keep it away from the auger. Gas auger: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire (a spark plug cap on some makes) and secure it away from the plug. Let the engine and muffler cool before you touch the bit or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown and isolation instructions in both the bit or attachment manual and the power-head or drill manual (a gas power head needs its own manual’s full shutdown). Only then free a stuck bit or clear wrapped material, using only the method your manual specifies (gloves do not make grabbing sharp wire or cutting edges safe), and check the bit and guards for damage. Do not handle unidentified wire, cables or pipes. Do not use reverse or run the engine or motor to back the bit out unless your manual expressly authorizes it for this task, with both hands on the designated handles and everyone clear of the bit; complete the full shutdown again before any further hands-on work. Add every step your manual gives, in its order, and refit every guard and shield before you restart.
Fitting and Checking the Bit
- Complete the full shutdown for your auger in the shutdown box above.
- Remove the old bit only as your manual describes. Ryobi and EGO use a locking pin with a clip, and other makers use other pins.
- Fit the new bit and pin as the manual shows, and confirm it is the bit your head takes.
- Check the bit for cracks or bends. Ryobi, EGO, Powermate and Makita all say to replace a cracked, bent or damaged bit.
- Refit every guard, then follow your manual’s start steps from a stable stance.
Before You Dig
Protect Yourself
Wear safety glasses with side shields or goggles meeting your manual’s specification, including ANSI Z87.1 where required, and add a face shield where required. Wear hearing protection with gas engines and wherever your manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional protection your manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep hair, clothing, gloves, hands and feet away from moving parts.
Clear the Area
Before you start, walk the spot and remove rocks, sticks, wire, hose, stakes and anything else the bit could catch or throw. Identify irrigation lines, drip lines, cables and sprinkler heads before you start, and take loose garden hoses out of the work area. Do not handle or move unidentified cables, pipes or utility lines: keep the auger away from them and contact the utility if their location is uncertain.
Call 811 First
Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm responses from every notified utility, including markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Follow state ticket-validity and tolerance-zone rules, preserve markings, and keep augers outside the required clearance area. Near marks, use careful hand digging or another locating method permitted by state rules and the utility; obey any stricter auger-manual prohibition. Arrange separate locating for private services that 811 does not cover (irrigation lines, cables). Do not dig where a service’s location remains uncertain, and do not switch to a larger machine to get around it. No augering depth above a buried service is safe.
According to PHMSA, all states have established one-call notification centers, and the call is free. Notice periods are set by state law, so check yours. In one study, simulation training cut utility strikes by 35 to 61 percent across a utility division over 12 months, which shows how much careful locating and digging practice matters (4).
Gas Augers Run Outdoors Only
Never start or run a gas auger indoors or in a garage or shed, even with the doors open. Start and run it outdoors: the exhaust contains deadly carbon monoxide, which has no color, taste or smell.
A medical examiner’s review of fatal cases tied to small engines, including generators and a pressure washer, found lethal carbon monoxide in poorly ventilated spaces, which makes the same point (5). Hearing matters too, since workers exposed to both hand-arm vibration and noise showed more hearing loss than unexposed workers in a review of agricultural and forestry studies (6).
Slopes and Frozen Ground
On a slope or uneven ground, slow down, keep firm footing and follow only the slope or footing rule in your own manual. If your manual gives no such instruction, obtain guidance from the manufacturer before using the auger on a slope. Do not dig in frozen or rock-hard ground or in ground full of roots and stones: the bit can bind and the machine can twist or kick.
Drill-Driven Garden Bits Are a Different Tool
Many search results for a 4-inch or 6-inch bit are drill-driven garden bits. A drill-driven bit is not an earth auger machine, because it has no engine or motor of its own and needs a drill or power head with its own manual. The comparison of earth auger vs garden auger drill bit belongs on its own page, and the size logic in this article is the same, since the diameter is still the hole. Skid steer and tractor bits are implements with their own manuals, and I give no operating advice for them here.
Mistakes I See With Hole Size
In my experience most hole-size mistakes come from reading the wrong number, not from the bit itself.
- Sizing to the face of the post. The diagonal is what has to clear, and for a post that measures 3.5 inches a face it is about 4.95 inches.
- Reading bit length as depth. The maker’s maximum depth is a separate figure that names its bit.
- Pressing hard to speed up a bigger bit. EGO says pressing excessively on the machine will not speed up the digging, and Echo says to let the auger drill with light downward pressure.
- Using a bit that does not match the head. Check your own manual for the bit your head takes.
- Digging before the 811 process. A wider hole does not make a buried line safer.
- Reading a diameter as a promise about soil. Only some makers tie capacity to a soil, and then only for their own tool.
On my own land, replacing a lost tree in the orchard is the job that makes me hold a tape against the root ball first. I plan the hole around that number, and the bit follows.
Choose the 4-Inch Bit If, Choose the 6-Inch Bit If
The choice follows the widest part of what goes in the hole. Measure that first, then match the bit and your machine’s own manual. My roundup of earth auger models compares gas, corded and battery machines.
Choose the 4-Inch Bit If
- The widest part of the post or stake is clearly under 4 inches.
- The job is a stake, a drip line header post, or a plant whose root ball is far narrower than the hole, since extension guidance asks for a planting hole two to three times the root ball width.
- Your manual lists a 4-inch bit for your head.
Choose the 6-Inch Bit If
- You are setting a square post whose diagonal is near 5 inches, such as a 4×4 that measures 3.5 inches a face.
- You have checked separately the hole and footing dimensions your fence plan or local rules require, because clearing the post is not the same as meeting them.
- Your manual lists a 6-inch bit for your head, and you will follow its rule on how many people run the machine.
If the post’s diagonal is wider than 6 inches, the 6-inch bit is too small. For a plant, size the hole from the root ball with the extension width rule above.
What to Remember Before You Buy a Bit
Measure the widest part of what goes in the hole, which for a square post is the diagonal. A 4 inch earth auger bit makes a 4-inch hole, and a 6-inch bit makes 2.25 times the area. Make the full shutdown the first step of every bit change, and call 811 before the first hole. My own tip is to keep a tape with the manual and write the measured post diagonal on its bit page, so the number is ready before the next job. Read your own manual’s bit line next, and see my 6-inch vs 8-inch auger bit comparison if you need a bigger hole. For most fence-post work on a homeowner machine, the 4-inch vs 6-inch auger bit decision starts with the post’s diagonal.
Frequently Asked Questions
What is the typical hole diameter for a 4×4 post?
The hole has to be wider than the diagonal of the post, which is about 1.41 times a face. For a post that measures 3.5 inches a face, that is about 5 inches, so a 6-inch bit is the smaller of the two sizes in this article that clears it. Check local practice for the diameter your fence needs.
How is an auger bit measured?
An auger bit is measured by its diameter, which is the width of the hole it makes. Its length is a separate figure and not the depth the machine will reach, since the maker prints a maximum depth that names the bit. EGO prints its bits in millimeters, so 150 millimeters is about 6 inches.
What size auger bit for fence post?
The bit has to make a hole wider than the post’s diagonal, so measure the post first. A 6-inch bit clears a 4×4 post that measures 3.5 inches a face, and a 6×6 post needs more than 6 inches. Use the geometry and the bit list in your manual.
How deep should a 6 foot fence post be in the ground?
Post length alone does not set the burial depth; soil, frost depth and the load on the post decide it. As one example, Penn State Extension gives a typical line post depth of 36 inches for a horse fence, with corner and gate posts often set to 48 inches, and says depth varies considerably with soil. Check your local code and frost depth before you dig.
Is a 4 inch auger bit big enough for a 4×4 post?
A 4 inch auger bit is not big enough for a 4×4 post, because the hole is narrower than the post’s diagonal. A post that measures 3.5 inches a face has a diagonal of about 4.95 inches. A 6-inch hole clears it with about half an inch at each corner.
References
- Wells C, Townsend K, Caldwell J, Ham D, Smiley ET, Sherwood M. Effects of planting depth on landscape tree survival and girdling root formation. Arboric Urban For. 2006;32(6):305-311.
- Armstrong T, Bir C, Foulke J, Martin B, Finsen L, Sjogaard G. Muscle responses to simulated torque reactions of hand-held power tools. Ergonomics. 1999;42(1):146-159.
- Mazaheri A, Rose LM. Reaction load exposure from handheld powered tightening tools: a scoping review. Int J Ind Ergon. 2021;81:103061.
- Gallagher AG, Hart M, Cleary D, et al. Proficiency based progression simulation training significantly reduces utility strikes: a prospective, randomized and blinded study. PLoS One. 2020;15(5):e0231979.
- Hyson BE, Friedman BM, Spear B, Bishop-Freeman SC. Lethal carbon monoxide generated from small internal combustion engines. J Anal Toxicol. 2024;48(8):625-629.
- Thaper R, Sesek R, Garnett R, Acosta-Sojo Y, Purdy GT. The combined impact of hand-arm vibration and noise exposure on hearing sensitivity of agricultural/forestry workers: a systematic literature review. Int J Environ Res Public Health. 2023;20(5):4276.
Safety Note: Only an adult who has read the manual and understands the controls should use an earth auger or post hole digger, never a child or anyone tired or impaired. Use the number of people your manual specifies, and keep everyone else out of the work area. The rotating bit can catch hair, clothing and gloves, and it can bind on a root, a rock or a buried object: the machine can then twist or kick in your hands. Stand with firm, balanced footing and hold the designated handles with both hands. Keep hands and feet away from the bit; never grasp or brace the bit or shaft. Never wrap the power cord around your hand, arm or body. If utility contact or a gas leak is suspected, stop work immediately. Do not touch, inspect, free or move the auger or exposed service, and do not attempt the normal hands-on shutdown or disconnect electrical connections in the suspected leak area. Leave the area, keep others away and contact the utility from a safe location; call 911 for a suspected gas leak or immediate danger. Otherwise, release the throttle or trigger immediately if the bit binds or control is threatened, then follow the shutdown procedure. On a two-person unit, both operators must understand the controls and agree on start and stop signals before starting; stop whenever either operator calls stop. Use reverse only where your manual expressly authorizes it. Never touch or clear the bit while it turns. Before you clear or free the bit, change or attach the bit, adjust, check or add oil or fuel, clean, load, move, store or leave the auger, complete the shutdown for its power type. Corded electric: release the switch or trigger, wait until the bit has stopped completely, then unplug it from the outlet by the plug, not the cord; before transport or storage, also let the motor cool. Battery: release the switch or trigger, wait until the bit has stopped completely, then remove the battery, and the switch key where the model has one. Gas: release the throttle, trigger or control, turn the engine off, wait until the bit and every moving part have stopped completely, then disconnect the spark plug wire and secure it away from the plug, and let the engine and muffler cool before touching the bit, engine, muffler or anything near the exhaust. For a drill-driven bit or any attachment system, follow the shutdown instructions in both the bit or attachment manual and the power-head or drill manual. If the bit sticks or material wraps around it, stop and complete the full shutdown before touching or inspecting it. Use only the freeing or clearing method specified in the exact manual; gloves do not make grabbing sharp wire or cutting edges safe. Do not handle unidentified wire, cables or pipes. Powered reverse is permitted only when the exact manual expressly authorizes it for that task, with both hands on the designated handles and everyone clear of the bit. Complete the full shutdown again before any subsequent hands-on work. Wear safety glasses with side shields or goggles meeting the manual’s specification, including ANSI Z87.1 where required; add a face shield where required. Wear hearing protection with gas engines and wherever the manual requires it. Wear long pants and sturdy, closed footwear with secure traction, plus any additional footwear protection the manual specifies. Tie back long hair, remove jewelry and secure drawstrings; do not wear loose clothing or loose gloves. Use the gloves specified for the task and keep them, clothing, hair, hands and feet away from moving parts. Contact 811 before digging and include every planned hole in the locate request. Wait the required state notice period and confirm that every notified utility has responded with markings or a clear/no-conflict response for the work area. Resolve missing or conflicting responses before digging. Preserve the marks and follow your state’s ticket-validity and tolerance-zone rules. Keep the auger out of the required clearance area; near marks, use careful hand digging or another locating method permitted by state rules and the utility. Follow any stricter prohibition in the auger’s manual. Marks do not show a safe drilling depth. Arrange to locate private irrigation lines, cables and other services that 811 may not cover. If a line’s location remains uncertain, do not dig there. Do not handle or move unidentified cables, pipes or utility lines. Before you start, remove rocks, sticks, wire and loose hoses, and identify irrigation lines, drip lines and sprinkler heads. Keep children, pets and other people out of the work area and at least the distance your exact manual specifies. Stop if anyone enters that area. If your manual gives no number, keep everyone well clear of the work area as it directs. No single distance is safe for every auger. On a slope or uneven ground, slow down, keep firm footing and follow only your manual’s rule. Do not dig in frozen or rock-hard ground. Before refuelling, complete the full gas shutdown described above. Refuel outdoors on the ground, not in a truck or trailer, with the engine cooled. Keep fuel away from smoking, flames, sparks and other ignition sources. Use an approved fuel container, avoid overfilling, secure the cap and follow the manual’s spill-cleanup and restart-location instructions; do not start with a fuel leak. Use the specified fuel and oil arrangement for that engine. Never start or run a gas auger indoors, in a garage or shed, or in an enclosed or poorly ventilated area, even with doors open. Operate outdoors where exhaust cannot accumulate or enter occupied spaces through doors, windows or air intakes. Exhaust contains deadly carbon monoxide. For a corded auger, inspect the cord and extension cord before use and do not use damaged cords or plugs. Use an outdoor extension cord meeting the exact manual’s gauge, length, plug and grounding requirements, and follow its GFCI instructions. Keep connections dry and the cord clear of the bit, heat, oil and sharp edges. Never carry the auger by its cord or wrap the cord around your body. Do not use it in rain or wet conditions prohibited by the manual. Use only manufacturer-approved batteries and chargers for the exact model. Complete the battery shutdown before removing or changing a battery, and keep the switch off and fingers off the trigger when installing one. Do not use damaged or modified batteries or chargers. Keep loose battery terminals away from metal objects, and follow the battery and charger manuals for moisture exposure, charging temperature, cooling and storage. Load and unload only as your manual describes, and store the auger dry and out of children’s reach. Take breaks and stop when you are tired.

