A woman spraying a hedge with an 18V battery backpack sprayer, a red 20V model resting in background

18V vs 20V Battery Sprayer: What the Printed Figures Really Compare

The 18V vs 20V battery sprayer question comes down to the makers’ own labels, and the figures printed for tank, flow, pressure and charging are what separate one sprayer from another. I studied plant protection, and I read a sprayer’s printed figures before I look at its badge. Below I set two 18V backpack sprayers against two sprayers labeled 20V, show what Craftsman prints about its 20V label, and say what stays unanswered.

18V vs 20V Battery Sprayer: What the Labels Say and What the Figures Say

The 18V and 20V on a battery sprayer are labels each maker chooses, and a label alone does not rank two sprayers. Craftsman explains its label in a footnote, quoted in the next section, and that footnote covers Craftsman’s own battery. My comparison of 20V and 56V backpack sprayers sets DEWALT, Craftsman and EGO side by side at the higher voltage labels.

The useful comparison is the printed figures of named models: tank size, flow and pressure from each maker’s chart, what is in the box, charger time and warranty. The sections below give those figures model by model and then side by side.

Short Answer

Treat 18V and 20V as each maker’s own label. Compare the printed tank, flow, pressure, charger and warranty figures, and read the manual of your exact sprayer before you buy a battery or a charger.

What Craftsman Prints About Its 20V Label

Craftsman’s product page for the CMXCAFG190682 carries this footnote: “20V MAX battery, maximum initial battery voltage (measured without a workload) is 20 volts. Nominal voltage is 18.” I go through that kit in my Craftsman V20 sprayer review.

In Craftsman’s words, the 20 is a maximum measured with no load on the battery, and the 18 is the nominal figure. DEWALT’s product page for the DXSP190681 shows “20V” with no footnote, and its manual prints no voltage for the sprayer. Makita’s manual for the XSU01Z prints a rated voltage of D.C. 18 V.

I use the footnote for Craftsman and nothing more. I do not read it into another maker’s sprayer, and I do not claim that either label sprays better.

Two 18V Backpack Sprayers: Makita XSU01Z and Field King 190723W

Both of these backpack sprayers carry an 18V label. They differ more in what comes in the box and how they control flow than in the label. My guide to 12V and 18V battery sprayers runs the same printed-figure check on the lower voltage labels.

The Makita XSU01Z is a 2.6 gallon (10 L) backpack sprayer sold as a tool only, so the battery and the charger are extra. According to Makita’s manual, its maximum working pressure is 0.5 MPa. With the 2-head nozzle it works at about 0.34 MPa and 0.24 gpm, and with the weedkiller nozzle at about 0.12 MPa and 0.45 gpm. Makita prints a weight of 12.3 to 13.0 lb empty, depending on the attachments and battery cartridges, and a 3-year limited warranty on its product page. The manual limits the sprayer to consumer grade water-based lawn and garden products and forbids acidic, caustic and flammable liquids.

The Field King 190723W is an 18V lithium-ion backpack sprayer with a 10-position flow dial, and Field King lists a 4 gallon tank. Its manual prints a chart, for water or a similar liquid, for the included nozzles that runs from 0.14 to 0.58 gpm and from 3 to 67 psi by nozzle and dial position, and the adjustable cone reaches 77 psi at dial 7. The manual says the sprayer keeps flow constant regardless of battery depletion state. The fast charger takes about 1.25 hours for the 36 Wh (2.0 Ah) battery and the slow charger about 3.5 hours, according to the manual, which also marks the sprayer for household use only. I cover the ProMax model from the same maker in my Field King 4-gallon sprayer review.

Two 20V-Labeled Backpack Sprayers: DEWALT DXSP190681 and Craftsman CMXCAFG190682

These two 4 gallon backpack sprayers are each a 20V backpack sprayer by their makers’ own label, and each maker controls flow in a different way.

The DEWALT DXSP190681 has a 10-position flow dial. According to its manual, positions 1 to 3 work off a low-pressure cutoff and positions 4 to 10 work off a high-pressure cutoff. The nozzle chart, for water or a similar liquid and with a variation of about 10 percent, runs from 0.14 to 0.58 gpm and from 3 to 77 psi across the six nozzles in the box. DEWALT’s manual says the sprayer keeps flow constant regardless of battery depletion state, prints no voltage, runtime or weight for it, and gives a 3-year limited warranty, with the battery under its own terms. The full kit gets its own write-up in my DEWALT 4-gallon sprayer review.

The Craftsman CMXCAFG190682 uses a two-position High/Low switch instead of a dial. Craftsman’s manual says the high setting uses nominal battery voltage to power the electric diaphragm pump, and the low setting reduces the voltage supplied to the pump and suits precision spraying. Its chart, for water or a similar liquid and with a variation of about 10 percent, runs from 0.17 to 0.39 gpm and from 10 to 51 psi across four nozzles, and it marks the full cone nozzle on High as a risk to the pump with frequent use. The manual’s package contents include the battery and the charger, and the warranty is three years, two years for batteries.

The Printed Figures Side by Side

The table puts the printed figures next to each other. Each cell is that maker’s own figure for that model, so read across a row to see what each one prints, never to rank one maker against another. My head-to-head of DEWALT and Craftsman backpack sprayers goes through those two models in more detail.

Printed figures for four battery backpack sprayers. Chart flows and pressures for Field King, DEWALT and Craftsman are for water or a similar liquid, and DEWALT and Craftsman print a variation of about 10 percent.
Figure Makita XSU01Z Field King 190723W DEWALT DXSP190681 Craftsman CMXCAFG190682
Label 18V (manual: D.C. 18 V) 18V 20V (maker’s page) 20V (maker’s page, V20 mark)
Tank, maker’s figure 2.6 gal (10 L) 4 gal 4 gal 4 gal
Flow control Not listed 10-position dial 10-position dial High/Low switch
Flow, maker’s figure 0.24 gpm (2-head nozzle), 0.45 gpm (weedkiller nozzle) 0.14 to 0.58 gpm (included nozzles) 0.14 to 0.58 gpm (included nozzles) 0.17 to 0.39 gpm (four nozzles)
Pressure, maker’s figure Maximum 0.5 MPa (up to 73 PSI on Makita’s page) 3 to 67 psi (cone to 77 psi at dial 7) 3 to 77 psi 10 to 51 psi
Battery and charger in the box Not included Battery and charger Battery and charger Battery and charger
Charger time, maker’s figure Not listed About 1.25 h fast, about 3.5 h slow (36 Wh battery) Not listed Not listed
Runtime, maker’s figure Up to 6 hours with a 4.0 Ah battery (Makita’s page) Not listed Not listed Not listed
Empty weight, maker’s figure 12.3 to 13.0 lb, depending on battery cartridge Not listed Not listed Not listed
Warranty 3 years (Makita’s page) Not listed 3 years (manual), battery under its own terms 3 years, 2 years for batteries (manual)

A cell that says Not listed stays empty, and a figure from a different model does not belong in it. Makita prints an empty weight and Field King prints charge times, and each runtime figure belongs to the sprayer it is printed for. No row in the table ranks the labels, because the figures belong to different makers, nozzles and test conditions.

Batteries, Chargers and Safety With Either Label

Both labels sit on lithium-ion batteries, so the same hazard and the same rule apply: the maker’s battery, the maker’s charger and the manual of your exact sprayer. OSHA’s fact sheet for workplaces says lithium-ion batteries can go into thermal runaway, which can cause fire and explosion, and it lists following the manufacturer’s instructions for storage, use, charging and maintenance as a control (1). Safety concerns from thermal runaway are also a recognised limit on wider use of these batteries (2).

Full Shutdown Box: Emergency First

Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown.

Full Shutdown Box: Before You Open, Fill, Clean or Charge

Shutdown before you open the tank, fill or refill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, move, store or leave the sprayer. Never point the wand at yourself, another person or a pet. During normal spraying, move only as the equipment manuals and the product label permit; walking while spraying with a backpack unit, or driving a mounted boom at the spraying speed its manual describes, is operation, not transport. Never ride while operating a hand-held wand or lance.

Full Shutdown Box: Battery Sprayer

Battery sprayer (handheld or backpack): release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery and keep it away from the sprayer.

If your exact manual gives no pressure-relief procedure, as Makita’s manual for the XSU01Z prints none, obtain manufacturer guidance before you open or loosen anything, and never borrow another model’s procedure.

Full Shutdown Box: Protective Equipment and Refitting

Wear the protective equipment the product label requires while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual; never clear a nozzle with your mouth and never by blowing into it. Add every step your manual gives, in its order. Refit every part, close the lid and check for leaks with clean water before product goes back in.

Use only the battery and charger the maker supplies or lists for your exact sprayer, and charge, store and handle the battery only as your manual describes.

To change or charge a battery, first complete the full shutdown in the shutdown box, including its emergency exception, which ends with removing the battery; begin the change or the charging only after that. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger, and follow the manual’s directions if a battery or charger gets wet. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using it without handling or removing it, keep people away and follow the battery manual’s emergency instructions; if it smokes or burns, move away and call 911 or the fire department.

Each maker names its own batteries. Makita lists six slide cartridges for the XSU01Z (BL1820B, BL1830, BL1830B, BL1840B, BL1850B and BL1860B), Craftsman lists four batteries for the CMXCAFG190682 (CMCB202, CMCB204, CMCB206 and CMCB209), and DEWALT’s manual lists its own set of packs by model number. Use only the batteries your manual lists, whatever label is printed on the tool.

DEWALT’s manual says to charge its battery packs only in designated DEWALT chargers, and Craftsman’s manual sets a temperature range for charging its battery pack, so read that range in the manual before you charge. Makita’s manual says not to use a corded power supply, such as a battery adapter or a portable power pack, with the XSU01Z. Read the charging conditions in the manual of your exact battery and charger before you charge.

Before you fill, complete the full shutdown for your sprayer in the shutdown box above. On a first fill I use clean water only, with the battery still out. I check the tank, strainer, hose and nozzle first, fill to the graduation marks, close the lid, put the battery in last with the power off and the trigger released, and then I watch the fittings, the hose and wand joints and the tank seams for drips without touching pressurized parts. DEWALT’s and Craftsman’s manuals both ask for a plain water test before product goes in. Before you open the tank, correct a leak or add product, complete the full shutdown for your sprayer in the shutdown box above, including its emergency exception.

Before you store the sprayer or its battery, complete the full shutdown for your sprayer in the shutdown box above, including its emergency exception. When the season ends, I keep the battery on a shelf, out of the sprayer and out of the charger, in a cool dry place, which is how DEWALT’s manual describes long storage. My guide to storing a sprayer battery lays out what nine maker manuals print.

Pesticide Safety Before Product Goes in the Tank

A battery sprayer is a pump, a hose and a wand under pressure that delivers a liquid, and many of those liquids are pesticides, which are legal products with a label that governs their use. The label rules below apply to every sprayer in this comparison, whatever its voltage label says. If pesticides are your main job, I rank battery sprayers for pesticides by tank and battery.

The product label is the law. It tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftover product and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. Your sprayer’s manual does not replace the label, and the label does not replace the manual: read the label before you open the container, and follow both.

DEWALT’s and Craftsman’s manuals say never to use flammable or combustible chemicals, caustics, bleach, acids, hot water or pressure producing chemicals in the sprayer, and never to store chemicals in it. Makita’s manual lists the liquids it allows and forbids and says to use only consumer grade water-based lawn and garden products. A manual’s list of forbidden liquids is a limit that no label or advice overrides.

Wear the protective clothing and equipment the product label requires, and put it on before you open the container. Wear the eye protection and gloves the label names every time you mix, load, spray, clean the tank or clear a nozzle.

Cornell’s pesticide safety program also advises chemical-resistant gloves, goggles and a respirator when you handle moderately toxic products, even when the label does not call for them. Wear every respirator the label requires, of the type the label names, and follow the respirator maker’s instructions for fit, use and care. If you follow Cornell’s advice and wear one the label does not require, or if it is unclear which respirator or filter is right, get qualified guidance on the respirator and filter before you handle the product. Protective equipment lowers your exposure; it does not make spraying safe.

Each manual adds its own equipment. Makita’s manual says to wear eye protection with side shields or goggles marked to comply with ANSI Z87.1, respiratory protection, appropriate protective clothing and gloves. Field King’s manual says to use the equipment the chemical’s maker recommends, which includes at least goggles, gloves and protective clothing. DEWALT’s and Craftsman’s manuals say the same and add that everyday eyeglasses are not safety glasses and that ANSI Z87.1 eye protection is required. Where a manual calls for respiratory protection, follow the respirator maker’s instructions for fit, use and care, and get qualified guidance on the respirator and filter before you handle the product if the right one is unclear.

A critical review of studies on coveralls for agricultural pesticide users found that the real-world protection may be over-estimated (3).

The product label, not this page, gives the amount of product, the dilution and the mixing order, so read it before you mix. Do not combine products unless the mixture complies with every product’s label and its compatibility has been established through the manufacturers or a qualified pesticide specialist; nobody’s advice overrides a label prohibition.

Before you mix or load the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the product label and your manual require for the task. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill or overflow cannot reach a well, a drain or other water. Read the label before you open the container, stand upwind, and do not eat, drink or smoke while you handle pesticides. Never use your mouth to siphon a pesticide from its container.

Keep the fill hose above the level of the liquid in the tank so the product cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Use measuring tools kept only for pesticides, never kitchen utensils or food containers. Mix only as much as the job needs so the tank ends empty; do not store leftover mix in the sprayer for later, because it can damage the sprayer’s parts.

If someone is exposed to a pesticide, follow the first-aid section of the product label and call Poison Control (America’s Poison Centers) at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.

Before you store the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception. Store pesticides in their original containers, with the label on, locked up or under the control of a person who can keep others away, and out of the reach of children.

Never put a pesticide in a container used for food, drink or household products. Keep pesticides away from food, animal feed and protective equipment, and store pesticides and fertilizers apart, because they can react with each other and start a fire. Store the sprayer drained, cleaned and dry, as your manual describes, with the battery stored as the battery manual describes.

What a Voltage Label Does Not Tell You About a Sprayer

The label says nothing about the nozzle, the flow or the droplets, and those printed figures are what change how a sprayer behaves in a yard. In a test-rig study of agricultural boom nozzles, nozzle type, nozzle size and pressure each changed the droplet size and speed (4). A bench test of a knapsack sprayer at 15 and 25 psi, a hollow cone nozzle gave the highest coverage and a flat fan air-induction nozzle gave the largest droplets (5). Both are measured examples on their own equipment, not a ranking of nozzles for your sprayer. I explain what a spray nozzle is, including nozzle types, droplet size and drift.

A sprayer’s maximum pressure is the limit of the machine, not a setting to aim for. The product label and the nozzle’s maker decide the pressure and the nozzle for a job. Higher pressure makes more fine droplets that drift, and the nozzle you choose changes the droplet size. NDSU Extension and K-State Extension give pressure ranges written for farm and boom sprayers, and those ranges differ, so neither is a setting for these backpacks. My guide on what PSI means on sprayers shows how to read pressure, ranges and limits.

Before you change a nozzle, complete the full shutdown for your sprayer in the shutdown box above. DEWALT’s and Craftsman’s manuals both say to turn the dial or the switch to the low setting when you change to a low-flow nozzle, and both say that ignoring the nozzle chart may damage the pump and void the warranty. I read each chart before I choose a nozzle, because the chart tells me what a tank will last and the badge does not.

The chart also gives a tank-time check you can do yourself. At Makita’s printed 0.24 gpm, a 2.6 gallon tank empties in about 11 minutes of continuous spraying with the 2-head nozzle. At Craftsman’s printed 0.22 gpm on Low with the narrow fan nozzle, a 4 gallon tank lasts about 18 minutes. These sums use printed flows for water, and they move with the nozzle and the setting. I explain how to choose a tank size in my comparison of 2 and 4 gallon sprayers.

Which Label Fits Which Yard

Pick the sprayer from its printed figures and from the batteries you already own. Makita prints an empty weight of 12.3 to 13.0 lb, depending on the attachments and battery cartridge, and the other three print no empty weight to set beside it, while the XSU01Z comes without a battery or a charger. For a 4 gallon tank with a 10-position flow dial, Field King and DEWALT print one, and Craftsman uses a two-position switch instead. Skip any of them if you need a figure the maker does not print for that model, such as a runtime under stated conditions. Choose any 18V vs 20V battery sprayer by the printed tank, flow, charger and warranty figures that fit your yard. If you settle on a 4 gallon tank, my picks among 4-gallon battery backpack sprayers are ranked in one roundup.

Frequently Asked Questions

Does Craftsman make a battery-powered sprayer?

Craftsman makes a battery-powered sprayer in its CMXCAFG190682 4 gallon backpack model, which carries a V20 mark. Its manual lists four Craftsman batteries for it (CMCB202, CMCB204, CMCB206 and CMCB209) and a three-year limited warranty, two years for batteries.

Does DeWalt make a battery-powered backpack sprayer?

DEWALT makes a battery-powered backpack sprayer in its DXSP190681 4 gallon model, labeled 20V on the maker’s page. Its manual describes a 10-position flow dial and a nozzle chart, and gives a three-year limited warranty.

Does Makita make a battery sprayer?

Makita makes the XSU01Z, a 2.6 gallon battery backpack sprayer sold as a tool only, so the battery and the charger are extra. Its manual prints a rated voltage of D.C. 18 V and a maximum working pressure of 0.5 MPa.

What is the difference between 18V and 20V batteries?

The difference between 18V and 20V batteries, in Craftsman’s wording, is that a 20V MAX battery has a maximum initial voltage of 20 volts measured without a workload and a nominal voltage of 18. That footnote speaks for Craftsman’s own batteries, so read another maker’s own wording before you compare.

Which battery backpack sprayers are labeled 18V?

The Makita XSU01Z and the Field King 190723W are two battery backpack sprayers labeled 18V. Makita’s manual prints D.C. 18 V, and Field King labels its sprayer as an 18V lithium-ion model.

References

  1. Occupational Safety and Health Administration. Lithium-ion Battery Safety. Fact Sheet DTSEM FS-4480. US Department of Labor; January 2025.
  2. Wang G, Ping P, Kong D, et al. Advances and challenges in thermal runaway modeling of lithium-ion batteries. Innovation (Camb). 2024;5(4):100624.
  3. Garrigou A, Laurent C, Berthet A, et al. Critical review of the role of PPE in the prevention of risks related to agricultural pesticide use. Saf Sci. 2020;123:104527.
  4. Nuyttens D, Baetens K, De Schampheleire M, Sonck B. Effect of nozzle type, size and pressure on spray droplet characteristics. Biosyst Eng. 2007;97(3):333-345.
  5. Alheidary MHR. Influence of nozzle type, working pressure, and their interaction on droplets quality using knapsack sprayer. Iraqi J Agric Sci. 2019;50(3).

Safety Note: Read your sprayer’s manual and the product label before you open any container. The label is the law: it tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftovers and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. This page never gives an amount of product, a dilution or a mixing order: the label does. Wear the protective clothing and equipment the label requires, put it on before you open the container, and wear the eye protection and gloves it names whenever you mix, load, spray, clean the tank or clear a nozzle. Protective equipment lowers your exposure; it does not make spraying safe. Wear every respirator the label requires, of the type it names, and follow the respirator maker’s fit, use and care instructions. Before you clean or store the sprayer, or wire a 12V pump, complete the shutdown below first. Before you mix or load, complete the shutdown below, including its emergency exception. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill cannot reach a well, a drain or other water. Stand upwind, never use your mouth to siphon a product, keep the fill hose above the liquid so it cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Mix only what the job needs, and do not store leftover mix in the sprayer. Never point the wand at yourself, another person or a pet, and never test a spray against your hand. Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Otherwise, before you open the tank, fill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, load, unload, transport, store or leave the sprayer, or lift, put on or take off a backpack unit, complete the shutdown. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Battery sprayer: release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery. 12V vehicle sprayer: first stop and secure the vehicle as its manual directs, then release the trigger, close the wand or boom valve and switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies, and reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the label’s protective equipment while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual, never with your mouth and never by blowing into it. Refit every part and check for leaks with clean water before product goes back in. For the first water test, complete the shutdown first, fill the tank with clean water and close it as your manual directs, connect the power only when you are ready, and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts; complete the shutdown again before you open the tank, fix a leak or add product. Wind, heat and fine droplets carry spray off target: the label may be stricter than any extension guideline, and extension sources give different wind figures, so no single number fits every situation. Do not spray during a temperature inversion, and do not assume that calm air, early morning or evening is suitable. Do not spray just before rain. Keep children, pets and other people out of the area while you spray and off the treated area for as long as the label says, and remove toys and cover pet food and water dishes first. The label’s pollinator wording decides when you may spray around flowering plants, and early morning or evening is not automatically suitable. A sprayer that has held weed killer should stay a weed-killer sprayer: extension services advise a dedicated sprayer, and rinsing may not remove every residue. Follow the product label’s instructions for rinsing empty containers, handling rinse water and disposing of them, and never reuse an empty pesticide container; for leftover product, call your state pesticide agency or a household hazardous waste program, and never pour it down a sink, a toilet or a storm drain. Store pesticides in their original containers, locked up and out of the reach of children, away from food and animal feed, and keep pesticides and fertilizers apart. If someone is exposed, follow the first-aid section of the label, call Poison Control at 1-800-222-1222 and keep the label with you; call 911 in an emergency. If product spills, keep people and animals away and follow the label’s emergency directions; try to contain a small spill only if the label says that is safe and you have the protective equipment it requires, and otherwise get help (the emergency number on the label, Poison Control if anyone is exposed, 911 for a fire, immediate danger or a large spill). Use only the battery and charger the maker supplies or lists for your exact sprayer, charge and store the battery as your manual describes, and do not use a damaged battery or charger: lithium-ion batteries can overheat and catch fire. Wire a 12V pump the way your manual says and use the fuse it lists. On an ATV or UTV, wear the helmet and protective gear the Consumer Product Safety Commission recommends, get hands-on training, sit only in the positions the manufacturer designed, never ride with more passengers than there are seats, and in a UTV fasten the seat belts and keep every part of your body inside the vehicle; stay within the rack and tow capacity in your vehicle’s owner’s manual, and remember that sloshing liquid shifts weight and changes how the vehicle handles; Montana State University Extension advises against riding and spraying if you have to hold a wand or lance. Stop at once, complete the full shutdown and inspect if the sprayer leaks, loses pressure or runs without spraying, and restart only as the manual allows. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, do not handle or remove it: keep people away, follow the battery manual’s emergency instructions, and if it smokes or burns, move away and call 911 or the fire department. Before you fill the tank, complete the shutdown, and fill it only to the level your manual allows. Carrying a full tank is tiring: rest when you are tired.

Scroll to Top