A man crouching in a vegetable bed, holding a spray wand with a brass nozzle emitting a fine mist

What Is a Spray Nozzle? Types, Droplet Size and Drift Basics

A spray nozzle is the small part at the end of a sprayer wand that breaks the liquid into droplets and shapes the spray into a pattern. The tank, pump and hose only move liquid, so the nozzle decides how wide the spray fans out and how fine the droplets are, and fine droplets drift more easily.

I studied plant protection, so I read a sprayer from the nozzle backward. Below you will find the main spray patterns, how droplet size is set, where drift starts, how to look after a nozzle safely and what your manual and the product label decide.

What Is a Spray Nozzle and What Does It Do?

The part that sprays is the nozzle, and everything behind it exists to feed it. Purdue Extension lists four jobs a nozzle does in milliseconds: it meters the flow, it atomizes the liquid into droplets, it forms a pattern that covers the target and it keeps the droplets moving so they reach it. Without one, the liquid would leave the wand as a stream with no purpose in the application. My guide to powered garden sprayer basics shows the types and parts that sit behind the nozzle.

  • Meters the flow: the size of the opening limits how much liquid leaves the wand at a given pressure.
  • Makes droplets: liquid pushed through a small opening breaks into a cloud of droplets of many sizes.
  • Shapes the pattern: the nozzle fans the spray into a flat sheet, a ring or a solid cone.
  • Aims the droplets: the spray leaves with enough speed to reach the target instead of hanging in the air.

I tell people to treat the nozzle as the one part of a sprayer that changes the result with no motor, no battery and no software. A new tip costs little, and it changes what lands on the plant more than a bigger tank does. That is my opinion from calibrating sprayers, not a rule from a test.

Nozzle and Tip, Two Related Parts

People use the two words as if they were one. Purdue says the tip is the part inserted into a cap, made of stainless steel, plastic, ceramic or brass, and the nozzle is the whole assembly that holds the tip. Some nozzles are molded as one piece, and then the unit is simply called a nozzle. The tip is the part you order when it wears out, and the manual of your sprayer names the one that fits.

What a Spray Nozzle Looks Like

On a garden sprayer the nozzle is a small cap on the end of the wand, with a tiny opening in the middle called the orifice. The opening is so small that you read its size from the maker’s markings and not by eye. What you notice in use is the pattern: a flat sheet, a ring or a solid cone of spray. Nozzle materials differ, and the next sections explain why that matters. I read the size markings on a new tip before it goes on the wand, because the opening is too small to judge by eye.

Types of Spray Nozzles by Spray Pattern

NDSU Extension says that although there are many nozzles, there are only three basic spray patterns: the flat fan, the hollow cone and the full cone (1). Flood nozzles and adjustable cone nozzles are variations on those shapes. This is the overview of the different types of spray nozzles.

Flat Fan Nozzles

A flat fan spray nozzle throws a thin, wide sheet with tapered edges. NDSU says it is widely used for broadcast spraying on farm booms, where the sheets of neighboring nozzles must overlap to give an even coverage. Lower pressure gives larger droplets and higher pressure gives finer ones, which drift more easily. I learn the pattern name first, because the nozzle maker’s tables are sorted by it. My guide to the fan spray nozzle goes deeper on pattern, angle and droplet size.

Flood Nozzles

A flood nozzle makes a wide, flat pattern like a fan but with a less even distribution. NDSU says that on a boom the pressure changes the width of a flood pattern more than that of a regular flat fan, and that flood nozzles reduce drift best within a low pressure range. Both statements describe farm boom nozzles, not a backpack wand.

Hollow Cone and Full Cone Nozzles

A hollow cone nozzle sprays a ring with most of the liquid at the outer edge and fine droplets. NDSU says it is used where complete coverage of a leaf matters, that drift is higher with it than with other nozzles and that no cone pattern gives an even spread for broadcast work. A full cone nozzle fills the circle and makes larger droplets than a flat fan. My guide to the cone spray nozzle explains the hollow and full cone types.

Adjustable Cone Nozzles on a Backpack Wand

Changing, adjusting or cleaning a nozzle is hands-on work, and this page covers battery handheld and backpack sprayers. Complete the full shutdown in the box below before you touch any nozzle, and add every step your manual gives.

Full Shutdown Before Nozzle Work

Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Shutdown before you open the tank, fill or refill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, move, store or leave the sprayer. Never point the wand at yourself, another person or a pet. During normal spraying, move only as the equipment manuals and the product label permit; walking while spraying with a backpack unit, or driving a mounted boom at the spraying speed its manual describes, is operation, not transport. Never ride while operating a hand-held wand or lance. Battery sprayer (handheld or backpack): release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery and keep it away from the sprayer. Wear the protective equipment the product label requires while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual; never clear a nozzle with your mouth and never by blowing into it. Add every step your manual gives, in its order. Refit every part, close the lid and check for leaks with clean water before product goes back in.

Many backpack wands carry an adjustable cone nozzle, which can be set from a narrow spray to a wide cone. Penn State Extension describes a broadcast job with this type, in which the nozzle is swept from side to side, and its calibration steps use a mid-range setting that produces a somewhat solid cone. Whatever setting you use, keep it the same when you calibrate and when you spray.

Pro Tip

I keep the nozzle setting I calibrate with and write it on a tag on the wand, because a changed setting changes what comes out. That is a habit of mine, and the full calibration method belongs to its own topic.

Median droplet size by nozzle type at 40 PSI, from NDSU’s table of farm nozzles at 0.5 gallons per minute
Nozzle type Spray shape Median droplet size
Standard flat fan tip Flat sheet About 360 micrometers
Extended range flat fan tip Flat sheet About 370 micrometers
Flood tip Wide flat sheet About 450 micrometers
Hollow cone tip Ring About 260 micrometers
Full cone tip Solid circle About 680 micrometers

The table shows a trend, not a setting for your sprayer: a hollow cone tip makes the smallest droplets of the five, a full cone tip the largest. A backpack nozzle from a different maker, at a different flow, will give different figures.

How a Spray Nozzle Sets Droplet Size

Every nozzle makes a range of droplet sizes, not one size, and NDSU sums the range up with a single number called the volume median diameter: half the spray volume is in droplets larger than that number and half in smaller ones. Three things move the number: the size of the opening, the spray angle and the pressure.

  • Opening size: NDSU says small openings make small droplets and larger ones make larger droplets, and that going up one nozzle size is a good way to reduce the number of driftable fines. Wolf at Kansas State says the same about larger nozzle sizes.
  • Spray angle: with a flat fan at 40 PSI and 0.5 gallons per minute, NDSU’s table runs from about 810 micrometers for a 40 degree angle to about 310 for a 110 degree angle. Wider angles make a thinner sheet and smaller droplets, though they let the nozzle sit lower.
  • Pressure: NDSU says higher pressure than the nozzle’s design range raises the flow, shrinks the droplets and can distort the pattern, and that pressure recommendations of the nozzle maker should always be followed.

Here is a worked example with the numbers above. A droplet of 500 micrometers carries eight times the liquid of a droplet of 250 micrometers, because volume grows with the cube of the width, as LSU AgCenter explains. That is why a few large droplets can carry as much liquid as many small ones, and why the nozzle’s droplet range matters more than its average. I find the cube rule the quickest way to explain why fine droplets matter.

NDSU adds a point about pressure that surprises people: to double the flow from a nozzle, the pressure must go up by a factor of four (1). The sprayer’s maximum pressure is therefore not a dial to turn up, and the maker’s PSI figure is a ceiling for the machine. My guide to reading PSI on a sprayer explains pressure ranges and limits.

Pressure and Nozzle

A sprayer’s maximum pressure is the limit of the machine, not a setting to aim for. The product label and the nozzle’s maker decide the pressure and the nozzle for a job. Higher pressure makes more fine droplets that drift, and the nozzle you choose changes the droplet size.

Two bench studies show how much a nozzle matters. A test rig measured 32 combinations of nozzle type, size and pressure and found that each of the three changes the droplet size and speed, and that absolute figures vary with the equipment used (2). A bench test of a knapsack sprayer with six nozzle types at 15 and 25 psi found that the hollow cone nozzle gave the best deposit and coverage on test cards, while an air-induction flat fan gave the largest droplets (3). Both are bench tests, not a yard with plants and wind.

I read results like these as a warning against simple rules. If two nozzles at the same pressure can give very different droplets, a nozzle swap changes the job. That is why I do not move a nozzle from one sprayer to another without the manuals saying it fits.

Spray Nozzle Droplet Size and Drift

Drift starts with droplet size. LSU AgCenter calls droplet size the overwhelming factor influencing drift and says droplets smaller than 150 micrometers are drift-prone. Wolf at Kansas State writes that droplets over 150 microns resist evaporation much more than smaller ones, and that higher pressures create many more droplets under 100 microns (4). I keep 150 micrometers as the figure to remember, and I name LSU and Kansas State whenever I explain it.

Drift and Weather

Drift is spray carried off target by the air, and wind speed is the factor extension sources stress most. Their figures differ and none fits every situation, and your product label may be stricter than all of them. K-State Extension suggests spraying when the wind is under 10.1 miles per hour and says there is no maximum wind speed that fits every situation. LSU AgCenter says to avoid applying when the wind is above about 10 miles per hour. NC State says under 5 miles per hour when you calibrate with the product in the tank. Cornell gives no number and says not to take a chance by spraying in the wind. Do not spray during a temperature inversion, when cool air near the ground holds small droplets in the air, and do not assume that calm air, early morning or evening is suitable: check the actual conditions and follow every weather restriction on the product label. High temperature and low humidity make spray evaporate faster. Do not spray just before rain. Droplets smaller than about 150 micrometers drift most easily, and higher pressure makes more of them.

Coverage Against Drift

Small droplets cover and penetrate better, and LSU calls that a direct opposition to the use of large droplets. So a nozzle that cuts drift can also change how the spray lands on a leaf. The label decides where it states a droplet size, and Purdue notes that very few labels do.

Drift-Reducing Nozzle Designs

NDSU describes two flat fan designs made to cut fine droplets. A pre-orifice nozzle has a chamber ahead of the final opening that lowers the pressure at it, and an air-induction nozzle draws air into the body so that the spray becomes large, air-filled droplets.

In a wind tunnel test of five agricultural nozzles, drift-reducing designs gave median droplets up to 265 percent larger than a standard flat fan, and the share of droplets of 100 micrometers or less fell by up to 97.3 percent (5). A test hall study of a field-crop boom found that nozzle type and boom height both change potential drift (6). These tests used boom nozzles, so they say nothing about a battery backpack wand.

My view is plain: a low-drift nozzle is a tool, not a permission. Nozzle choice lowers one risk, and wind, height and the label still decide whether you spray. I never let a nozzle’s drift claim talk me into a windy day.

Nozzle Material, Wear and Plugging

Nozzles wear with use, and NDSU lists the common materials: brass, plastic, nylon, stainless steel, hardened stainless steel and ceramic. Brass is the cheapest but soft and wears fast, nylon resists corrosion although some chemicals make thermoplastic swell, and harder metals usually cost more and last longer. A worn nozzle changes the flow, which changes the spray, and NDSU calls a plugged nozzle one of the most frustrating problems that applicators have with sprayers.

The shutdown box in the adjustable cone section above comes before any hands-on nozzle work on a battery handheld or backpack sprayer: read it before you touch the nozzle, the strainer or the wand.

When the spray pattern looks uneven, streaky or thin, stop and complete the shutdown before you look at the nozzle. A partly blocked nozzle is the usual first suspect, and the strainer behind it is the second. NDSU’s boom guidance compares each nozzle’s output with the average of all the nozzles: one outside 5 percent of the average should be cleaned if it is plugged or replaced if it is worn, and one that exceeds the manufacturer’s specification by 10 percent or more is worn out and should be replaced. Those are boom checks, so for a single wand the maker’s table for your tip is the reference.

My rule for spare parts is simple: keep one spare tip of the exact type your manual lists, and never mix nozzle types on one wand or boom. NDSU gives the same advice for booms, to avoid mixing nozzles of different materials, types, angles or sizes.

Choosing and Checking a Spray Nozzle for Your Sprayer

Your manual and the product label decide the nozzle, for weed killer, liquid fertilizer and fruit trees alike. Choose a replacement nozzle listed in your sprayer’s manual. For weed control jobs, my roundup of battery sprayers for weed killer compares nine models for lawns, beds and paths.

Before the first fill with product, check the pattern with clean water. The sentences below cover the first water test.

First Water Test

Before the first water test, complete the full shutdown in the shutdown box, then fill the tank with clean water and close the lid as your manual directs. Connect the power (install the battery) only when you are ready to test. Run the sprayer and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts. Before you open the tank, correct a leak or add product, complete the full shutdown again. Before every use, check the tank, strainer, hose and nozzle, and fix any leak before product goes in. Follow your manual’s first-use steps.

I spray clean water onto a concrete pad away from people, pets and plants, and I look at the pattern before I trust a nozzle with anything else. A flat fan should look like an even sheet and a cone like an even ring or a solid circle, and a streak means stop. The picture on a pad says little about droplet size, which needs the maker’s data.

Calibration comes after the nozzle is chosen. Calibrate again whenever the nozzle, the pressure or the product changes, using the setting you will spray with. At scale I calibrated sprayers before every campaign, and the same idea works at home size. The label’s amount of product is never part of that figure. My guide on calibrating a backpack sprayer shows how to measure your own output.

Safety With Product in the Tank

Many sprayers carry pesticides, and a nozzle sends those products into the air as droplets. The label and the manual together set the rules. I read the label first and the manual second, before I think about any nozzle.

The Label Is the Law

The product label is the law. It tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftover product and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. Your sprayer’s manual does not replace the label, and the label does not replace the manual: read the label before you open the container, and follow both.

Protective Equipment

Wear the protective clothing and equipment the product label requires, and put it on before you open the container. Wear the eye protection and gloves the label names every time you mix, load, spray, clean the tank or clear a nozzle. Cornell’s pesticide safety program also advises chemical-resistant gloves, goggles and a respirator when you handle moderately toxic products, even when the label does not call for them. Wear every respirator the label requires, of the type the label names, and follow the respirator maker’s instructions for fit, use and care. If you follow Cornell’s advice and wear one the label does not require, or if it is unclear which respirator or filter is right, get qualified guidance on the respirator and filter before you handle the product. Protective equipment lowers your exposure; it does not make spraying safe.

Mixing and Loading

The product label, not this page, gives the amount of product, the dilution and the mixing order, so read it before you mix. Do not combine products unless the mixture complies with every product’s label and its compatibility has been established through the manufacturers or a qualified pesticide specialist; nobody’s advice overrides a label prohibition. Before you load the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the product label and your manual require for the task. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill or overflow cannot reach a well, a drain or other water. Read the label before you open the container, stand upwind, and do not eat, drink or smoke while you handle pesticides. Never use your mouth to siphon a pesticide from its container. Keep the fill hose above the level of the liquid in the tank so the product cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Use measuring tools kept only for pesticides, never kitchen utensils or food containers. Mix only as much as the job needs so the tank ends empty; do not store leftover mix in the sprayer for later, because it can damage the sprayer’s parts.

Cleaning, Storage and Children

Before you clean the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the label and your manual require. Clean the sprayer as soon as you can after use, because dried product is harder to remove than product still in solution. Empty the tank, rinse the tank, hose, wand and nozzle, and clean the strainers and screens, following the product label and your manual; extension guidance warns that water alone may not remove every product. Clean it away from desirable plants, wells and other water, and wash the outside. Do not pour leftover product or rinse water down a sink, a toilet or a storm drain, or onto bare ground. Before you store the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception. Store pesticides in their original containers, with the label on, locked up or under the control of a person who can keep others away, and out of the reach of children. Never put a pesticide in a container used for food, drink or household products. Keep pesticides away from food, animal feed and protective equipment, and store pesticides and fertilizers apart, because they can react with each other and start a fire. Store the sprayer drained, cleaned and dry, as your manual describes, with the battery stored as the battery manual describes. Follow the product label’s instructions for rinsing the empty container, handling the rinse water and disposing of the container, and rinse only a container the label directs you to rinse. Never reuse an empty pesticide container for any purpose. Keep children, pets and other people out of the area while you mix, load and spray, and keep them off the treated area for as long as the label says. Before you spray, remove toys and take away or cover pet food and water dishes.

If Someone Is Exposed

If someone is exposed to a pesticide, follow the first-aid section of the product label and call Poison Control at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.

Spray Nozzle Basics to Remember

Three points carry the page: the nozzle sets the pattern and the droplet size, pressure and nozzle size change both, and the label and the manual decide the rest. My tip is to spray clean water on a pad and read the pattern before every season. Next, find the nozzle on your own wand and look up its pattern and size markings in your manual. If you are choosing a whole sprayer next, my battery powered garden sprayers roundup compares nine handheld and backpack picks.

Frequently Asked Questions

What are the different types of spray nozzles?

The different types of spray nozzles come down to three basic patterns, the flat fan, the hollow cone and the full cone, according to NDSU Extension. Flood nozzles and adjustable cone nozzles are variations of those shapes.

What is the purpose of a spray nozzle?

The purpose of a spray nozzle is to meter the liquid, break it into droplets of a chosen size and shape the spray into a pattern that reaches the target. Purdue Extension describes these as the four jobs of a nozzle: meter, atomize, shape and keep droplet speed.

What does a nozzle look like?

A spray nozzle looks like a small cap on the end of the wand, holding a tip with a tiny opening called the orifice. Purdue says the tip can be stainless steel, plastic, ceramic or brass, and in use you see a flat sheet, a ring or a solid cone of spray.

How does a spray nozzle work?

A spray nozzle works by forcing liquid from the pump through a small opening, which breaks the stream into droplets released into the air. The size of the opening, the spray angle and the pressure set the droplet size and the pattern, according to NDSU Extension.

How does a spray nozzle affect spray drift?

A spray nozzle affects spray drift through the droplet size it makes, because LSU AgCenter calls droplet size the overwhelming factor in drift. Larger openings and lower pressure give larger droplets, and the product label and the weather still decide whether you spray.

References

  1. Proulx R. Spray Equipment and Calibration. AE73. North Dakota State University Extension; revised October 2025.
  2. Nuyttens D, Baetens K, De Schampheleire M, Sonck B. Effect of nozzle type, size and pressure on spray droplet characteristics. Biosyst Eng. 2007;97(3):333-345.
  3. Alheidary MHR. Influence of nozzle type, working pressure, and their interaction on droplets quality using knapsack sprayer. Iraqi J Agric Sci. 2019;50(3).
  4. Wolf RE. Strategies to Reduce Spray Drift. MF-2444. Kansas State University Agricultural Experiment Station and Cooperative Extension Service; March 2000.
  5. McGinty J, Baumann P, Hoffmann W, Fritz B. Evaluation of the spray droplet size spectra of drift-reducing agricultural spray nozzle designs. Am J Exp Agric. 2016;11(3):1-5.
  6. Balsari P, Gil E, Marucco P, van de Zande JC, Nuyttens D, Herbst A, Gallart M. Field-crop-sprayer potential drift measured using test bench: effects of boom height and nozzle type. Biosyst Eng. 2017;154:3-13.

Safety Note: Read your sprayer’s manual and the product label before you open any container. The label is the law: it tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftovers and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. This page never gives an amount of product, a dilution or a mixing order: the label does. Wear the protective clothing and equipment the label requires, put it on before you open the container, and wear the eye protection and gloves it names whenever you mix, load, spray, clean the tank or clear a nozzle. Protective equipment lowers your exposure; it does not make spraying safe. Wear every respirator the label requires, of the type it names, and follow the respirator maker’s fit, use and care instructions. Before you clean or store the sprayer, or wire a 12V pump, complete the shutdown below first. Before you mix or load, complete the shutdown below, including its emergency exception. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill cannot reach a well, a drain or other water. Stand upwind, never use your mouth to siphon a product, keep the fill hose above the liquid so it cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Mix only what the job needs, and do not store leftover mix in the sprayer. Never point the wand at yourself, another person or a pet, and never test a spray against your hand. Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Otherwise, before you open the tank, fill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, load, unload, transport, store or leave the sprayer, or lift, put on or take off a backpack unit, complete the shutdown. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Battery sprayer: release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery. 12V vehicle sprayer: first stop and secure the vehicle as its manual directs, then release the trigger, close the wand or boom valve and switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies, and reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the label’s protective equipment while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual, never with your mouth and never by blowing into it. Refit every part and check for leaks with clean water before product goes back in. For the first water test, complete the shutdown first, fill the tank with clean water and close it as your manual directs, connect the power only when you are ready, and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts; complete the shutdown again before you open the tank, fix a leak or add product. Wind, heat and fine droplets carry spray off target: the label may be stricter than any extension guideline, and extension sources give different wind figures, so no single number fits every situation. Do not spray during a temperature inversion, and do not assume that calm air, early morning or evening is suitable. Do not spray just before rain. Keep children, pets and other people out of the area while you spray and off the treated area for as long as the label says, and remove toys and cover pet food and water dishes first. The label’s pollinator wording decides when you may spray around flowering plants, and early morning or evening is not automatically suitable. A sprayer that has held weed killer should stay a weed-killer sprayer: extension services advise a dedicated sprayer, and rinsing may not remove every residue. Follow the product label’s instructions for rinsing empty containers, handling rinse water and disposing of them, and never reuse an empty pesticide container; for leftover product, call your state pesticide agency or a household hazardous waste program, and never pour it down a sink, a toilet or a storm drain. Store pesticides in their original containers, locked up and out of the reach of children, away from food and animal feed, and keep pesticides and fertilizers apart. If someone is exposed, follow the first-aid section of the label, call Poison Control at 1-800-222-1222 and keep the label with you; call 911 in an emergency. If product spills, keep people and animals away and follow the label’s emergency directions; try to contain a small spill only if the label says that is safe and you have the protective equipment it requires, and otherwise get help (the emergency number on the label, Poison Control if anyone is exposed, 911 for a fire, immediate danger or a large spill). Use only the battery and charger the maker supplies or lists for your exact sprayer, charge and store the battery as your manual describes, and do not use a damaged battery or charger: lithium-ion batteries can overheat and catch fire. Wire a 12V pump the way your manual says and use the fuse it lists. On an ATV or UTV, wear the helmet and protective gear the Consumer Product Safety Commission recommends, get hands-on training, sit only in the positions the manufacturer designed, never ride with more passengers than there are seats, and in a UTV fasten the seat belts and keep every part of your body inside the vehicle; stay within the rack and tow capacity in your vehicle’s owner’s manual, and remember that sloshing liquid shifts weight and changes how the vehicle handles; Montana State University Extension advises against riding and spraying if you have to hold a wand or lance. Stop at once, complete the full shutdown and inspect if the sprayer leaks, loses pressure or runs without spraying, and restart only as the manual allows. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, do not handle or remove it: keep people away, follow the battery manual’s emergency instructions, and if it smokes or burns, move away and call 911 or the fire department. Before you fill the tank, complete the shutdown, and fill it only to the level your manual allows. Carrying a full tank is tiring: rest when you are tired.

Scroll to Top