In a 12V vs 18V battery sprayer comparison, the voltage is the maker’s own label for its battery, and it says nothing by itself about how well the sprayer works. The figures that decide your job are tank size, printed pressure, the condition behind a runtime claim and the charge time.
My plant protection training and years of large-scale crop production taught me to read a spec sheet for the condition behind each number. Below I compare one 12V sprayer with three 18V models on their printed figures, then explain what a 12V vehicle unit is and which safety steps apply to both.
The 12V vs 18V Battery Sprayer Label and What It Tells You
The voltage on a sprayer is a label that its maker puts on the battery. PetraTools prints 12V for the HD2000-S, while Field King and Makita print 18V for the three models compared here. The label names the battery and gives no tank size, no pressure and no runtime. My guide to the 18V and 20V battery sprayer labels runs the same printed-figure check on a different pair.
I never read more volts as more power or a longer run. Each maker prints its own figures for each model, so I compare those and nothing else. Four of them matter most:
- Tank size: how much liquid the sprayer carries between fills, which sets how often you stop and open the tank.
- Printed pressure: the maker’s number and what it describes, whether a pre-set point, a ceiling or a working pressure with a named nozzle.
- Runtime and its condition: the hours a maker claims and the nozzle, pressure or battery size it names beside them.
- Charger and charge time: whether a charger comes with the sprayer and how many hours the maker prints for it.
Short Answer
Compare a 12V and an 18V battery sprayer on tank size, printed pressure, the condition behind the runtime and the charge time. Each maker’s voltage label names only its own battery.
Full Shutdown Before Any Hands-On Step
Every section below that has you fill, charge, adjust, open or clear a sprayer relies on this one box. Complete the full shutdown for your sprayer type before any hands-on step, including its emergency exception.
Full Shutdown Box for Battery and 12V Vehicle Sprayers
Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Shutdown before you open the tank, fill or refill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, move, store or leave the sprayer. Never point the wand at yourself, another person or a pet. During normal spraying, move only as the equipment manuals and the product label permit; walking while spraying with a backpack unit, or driving a mounted boom at the spraying speed its manual describes, is operation, not transport. Never ride while operating a hand-held wand or lance. Battery sprayer (handheld or backpack): release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery and keep it away from the sprayer. 12V vehicle sprayer (ATV, UTV, cart or tow-behind): first stop and secure the vehicle as its manual directs. Then release the trigger, close the wand or boom valve and switch the pump off at its switch. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies. Reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the protective equipment the product label requires while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual; never clear a nozzle with your mouth and never by blowing into it. Add every step your manual gives, in its order. Refit every part, close the lid and check for leaks with clean water before product goes back in.
The PetraTools HD2000-S as a 12V Battery Sprayer
The PetraTools HD2000-S is a 2 gallon battery sling sprayer: a tank you carry on a shoulder strap, with a 4 foot hose and an extendable wand. According to PetraTools, it runs on a 12V rechargeable battery, and the parts list in its manual names the pack as 12V 1.3 Ah. I rank sprayers of this tank size in my 2 gallon battery powered sprayer picks.
Battery, Tank and Charger
Before you charge or store this sprayer or open its tank, complete the full shutdown in the shutdown box above, including its emergency exception. PetraTools’ manual prints no pressure-relief procedure and does not describe removing the battery, so get PetraTools’ guidance on relieving pressure and isolating the power before you open or service the sprayer.
The manual’s box list includes a charger, and it says charging may take up to 4 to 6 hours, with a light that shows red while charging and green when full. It tells you to use the original charger, to store the sprayer with a full charge and to recharge it every three to six months. My answer to “how to store a sprayer battery” compares what nine maker manuals say.
I keep battery packs on a shelf in the machinery shed. The storage line is the first thing I read in any battery manual.
Pressure and Runtime
PetraTools gives the HD2000-S runtime as up to 2 hours and names no nozzle, pressure or battery condition beside it. Neither the manual nor PetraTools’ product page for the HD2000-S lists a pressure figure. A runtime with no named setting is a claim I cannot use to plan a job. I cover the HD2000-S in my review of the PetraTools sprayer.
The manual also says nozzle and hose connections may leak over time and asks you to check and re-tighten them before each use. Before you touch a connection, complete the full shutdown in the shutdown box above, together with the PetraTools guidance on pressure and power.
The 18V Battery Sprayers From Field King and Makita
Three 18V sprayers carry the same label and print three different sets of figures. Their pages show why the voltage cannot be the comparison.
Field King 190515 and Its Fixed 40 PSI
The Field King 190515 is a 4 gallon backpack, the type many buyers mean by a battery powered backpack sprayer. According to Field King, it runs on an 18V lithium-ion 2.1 Ah pack and is pre-set to spray at 40 PSI, with no dial to change the flow. My Field King sprayer review of the 190515 covers the 4 gallon ProMax in full.
Field King’s listing says up to 4 hours of spray time on a single charge with an 8002 nozzle, and gives 3.5 hours to charge the pack. The maker’s manual says actual battery life varies with spraying technique, the liquid and the nozzle. It tells you to use only the maker’s own batteries in good condition, to complete the full shutdown in the shutdown box above before you fill the tank or change the battery, and to test the sprayer with plain water before any chemical.
My first fill on any sprayer is clean water, and I follow the steps in the box below.
First Water Test and Pre-Use Check
Before the first water test, complete the full shutdown in the shutdown box, then fill the tank with clean water and close the lid as your manual directs. Connect the power (install the battery or connect the 12V supply) only when you are ready to test. Run the sprayer and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts. Before you open the tank, correct a leak or add product, complete the full shutdown again. Before every use, check the tank, strainer, hose and nozzle, and fix any leak before product goes in. Follow your manual’s first-use steps.
Field King 190723W and Its Dial and Chart
The Field King 190723W is the variable flow model, with a dial of 10 positions and a flow chart printed in its manual. For water and the nozzles in the box, the chart runs from 0.14 to 0.58 gpm and from 3 to 67 psi, depending on the nozzle and the dial position, and the adjustable cone nozzle reaches 77 psi at dial 7. The manual warns that a wrong nozzle and dial pairing may damage the pump, and it says to turn the dial to 1 to 3 when you switch to a low flow nozzle. I set the fixed pressure 190515 against the variable flow model in my Field King 190515 and 190723W comparison.
Its manual gives approximate charge times for two pack sizes, 36 Wh and 72 Wh: 1.25 hours and 2 hours on the fast charger, and 3.5 hours and 7 hours on the slow one. Before you charge or change a pack, complete the full shutdown in the shutdown box above. I read a flow chart like this one before I touch a dial.
Makita XSU01Z and Its Printed Pressures
The Makita XSU01Z is a 2.6 gallon (10 L) backpack sold as a tool only: the battery and the charger are not included. Makita rates it D.C. 18 V and uses its 18V LXT battery cartridges. Its manual prints a maximum working pressure of 0.5 MPa, which Makita’s product page gives as up to 73 PSI. My backpack sprayer vs handheld sprayer comparison helps you choose a carry style for your yard.
For the vertical two-head nozzle the manual prints a working pressure of about 0.34 MPa and a flow of about 0.90 L/min (0.24 GPM). With the weedkiller nozzle the figures are about 0.12 MPa and 1.70 L/min (0.45 GPM). Makita’s product page says up to 6 hours of run time with a 4.0 Ah 18V LXT battery, sold separately, and names no nozzle with it.
When I price a tool-only sprayer, I add the battery and the charger to the sum before I decide. I compare powered and hand-pumped options for yard work in my battery sprayer vs pump sprayer guide.
The Printed Figures Side by Side
The table keeps each maker’s figure with the condition it names. Where a maker prints no figure, the cell says so.
| Row | PetraTools HD2000-S | Field King 190515 | Field King 190723W | Makita XSU01Z |
|---|---|---|---|---|
| Battery label, maker’s figure | 12V | 18V | 18V | 18V LXT, rated D.C. 18 V |
| Battery size, maker’s figure | 1.3 Ah | 2.1 Ah | 36 Wh or 72 Wh pack | Not included, tool only |
| Tank, maker’s figure | 2 gal | 4 gal | 4 gal | 2.6 gal (10 L) |
| Pressure, maker’s figure | Not listed in the manual or product page | Pre-set 40 PSI | Chart: 3 to 67 psi on the included nozzles by dial position, 77 psi with the cone nozzle | Max 0.5 MPa (up to 73 PSI on Makita’s page); about 0.34 MPa working with the two-head nozzle |
| Runtime, maker’s figure | Up to 2 hours, no condition named | Up to 4 hours, with an 8002 nozzle | Not published | Up to 6 hours, with a 4.0 Ah battery |
| Charge time, maker’s figure | Up to 4 to 6 hours | 3.5 hours | 1.25 hours fast or 3.5 hours slow (36 Wh) | Charger not included |
I read the pressure row first, because it carries the most conditions. PetraTools lists none in its manual or product page, Field King prints a pre-set point on one model and a chart on the other, and Makita prints a ceiling and two working pressures. Each of those numbers describes something different, and I do not rank one maker’s PSI against another’s. My comparison of 20V and 56V backpack sprayers puts DEWALT, Craftsman and EGO side by side.
The runtime row works the same way. One claim names no setting, one names a nozzle and one names a battery size, so no two of them can be set against each other. A 12V label in the top row ranks nothing in the rows below it.
Why 12V Also Names Vehicle-Powered Sprayers
A 12V label also sits on sprayers that have no battery at all. The Chapin 97200E EZ Mount is a 15 gallon spot sprayer that, according to its manual, runs on 12 volt DC from a vehicle battery through a wire harness with an in-line fuse. It has no battery and no charger in the box, so it is a vehicle unit and I keep it out of the table. My look at the Chapin 15 gallon sprayer next to its 25 gallon sibling covers Chapin’s 12V vehicle units.
The manual prints a 60 PSI maximum, set by a pressure switch on the pump, and says that pressure “can only be adjusted by adjusting the nozzle”. Any nozzle adjustment starts with the full shutdown in the shutdown box above. It warns that a pinched or damaged harness may overheat and cause a melt down or fire, and it says the sprayer is designed to be attached to stable surfaces. Stay within the rack and tow capacity in your vehicle’s owner’s manual.
I read the wiring and fuse page of a vehicle unit’s manual before anything else, because that page carries the hazard this type adds.
12V Wiring
Before any wiring work on the pump, complete the full shutdown in the shutdown box, including its emergency exception and securing the vehicle. Wire the pump the way your sprayer’s manual says, and use the fuse the manual lists. To disconnect the supply, follow the shutdown box through securing the vehicle, stopping the pump and relieving the pressure, then disconnect it as your manual directs; reconnect it only after the work is complete, every part is secured and the pump switch is off.
Hand Wand on a Vehicle
Montana State University Extension advises not to ride and spray if you have to hold a wand or lance.
Pressure and Flow Belong to the Nozzle and the Job, Not the Voltage
What leaves the wand depends on the pump, the nozzle and the pressure, and those are the things the table describes. A voltage label describes none of them. My answer to “what does psi mean on a sprayer” explains pressure ranges and limits.
NDSU Extension’s farm-scale guide says pressure needs depend on the product and the nozzle, from low pressures of 15 to 40 PSI for most herbicides or fertilizer up to 400 PSI or more for insecticides or fungicides (1). Those are figures for farm sprayers, and no sprayer in this comparison prints a number near the top of that range.
A bench test of 32 nozzle and pressure combinations on agricultural boom nozzles found that nozzle type, size and pressure all change droplet size and speed (2). Tests on a knapsack sprayer at 15 and 25 psi found the best coverage on cards with a hollow cone nozzle and the largest droplets with an air-induction flat fan nozzle (3). It was one small experiment and it ranks no brand. My answer to “what is a spray nozzle” covers types, droplet size and drift basics.
Kansas State’s drift publication adds that higher pressures make many more small droplets (4). It was written for field and boom sprayers, so read it as a reason to treat any maker’s PSI as a limit and never as a target.
At scale I checked sprayer nozzle output with calibration cylinders before each campaign, and my answer to “how to calibrate a backpack sprayer” shows how to measure your own. The habit taught me to look for the nozzle named beside every pressure and runtime figure.
Pressure and Nozzle
A sprayer’s maximum pressure is the limit of the machine, not a setting to aim for. The product label and the nozzle’s maker decide the pressure and the nozzle for a job. Higher pressure makes more fine droplets that drift, and the nozzle you choose changes the droplet size.
Charging, Battery Care and Safety for Each Type
Both power types add a hazard to the liquid in the tank. A battery unit adds a pack and a charger, and a vehicle unit adds wiring and a fuse. The steps below come before any hands-on work with either.
Battery Units
OSHA’s fact sheet says lithium-ion batteries can undergo thermal runaway, which can cause fire and explosion, and it lists following the manufacturer’s instructions for storage, use, charging and maintenance as a control (5). It is a workplace sheet and not a sprayer rule. A 2024 modelling review says thermal runaway concerns limit wider use of lithium-ion batteries (6), and it says nothing about garden tools.
The makers say it in their own words. Field King’s manuals say to use only the maker’s own charger and batteries, and the 190723W manual adds not to expose the charger to rain and to store it indoors. Makita’s manual says to recharge only with the specified charger, not to charge in a damp or wet location and not to store the battery outside or in vehicles. PetraTools says to use the original charger.
Battery and Charger
Use only the battery and charger the maker supplies or lists for your exact sprayer, and charge, store and handle the battery only as your manual describes. To change or charge a battery, first complete the full shutdown in the shutdown box, including its emergency exception, which ends with removing the battery; begin the change or the charging only after that. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger, and follow the manual’s directions if a battery or charger gets wet. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using it without handling or removing it, keep people away and follow the battery manual’s emergency instructions; if it smokes or burns, move away and call 911 or the fire department.
Before Product Goes in the Tank
A sprayer holds whatever liquid you put in it, and many of those liquids are pesticides with a label that governs their use. The label rules the product, and the manual rules the machine. My answer to “what is a powered garden sprayer” covers types, parts and safety basics.
The Label
The product label is the law. It tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftover product and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. Your sprayer’s manual does not replace the label, and the label does not replace the manual: read the label before you open the container, and follow both.
Amounts and Mixes
The product label, not this page, gives the amount of product, the dilution and the mixing order, so read it before you mix. Do not combine products unless the mixture complies with every product’s label and its compatibility has been established through the manufacturers or a qualified pesticide specialist; nobody’s advice overrides a label prohibition.
Protective Equipment
Wear the protective clothing and equipment the product label requires, and put it on before you open the container. Wear the eye protection and gloves the label names every time you mix, load, spray, clean the tank or clear a nozzle. Cornell’s pesticide safety program also advises chemical-resistant gloves, goggles and a respirator when you handle moderately toxic products, even when the label does not call for them. Wear every respirator the label requires, of the type the label names, and follow the respirator maker’s instructions for fit, use and care. If you follow Cornell’s advice and wear one the label does not require, or if it is unclear which respirator or filter is right, get qualified guidance on the respirator and filter before you handle the product. Protective equipment lowers your exposure; it does not make spraying safe.
The manuals set their own minimums. Field King’s say at least goggles, gloves and protective clothing. Chapin’s says goggles, gloves, a long sleeve shirt, long pants and full foot protection when spraying. Makita’s calls for eye protection with side shields or goggles marked to comply with ANSI Z87.1, a face or dust mask and gloves, and PetraTools’ says protective clothing, gloves, and eye and respiratory protection as the chemical maker instructs. Wear whichever is stricter, the label’s or the manual’s.
A critical review of agricultural pesticide users found that the real-world effectiveness of protective clothing may be over-estimated (7). It centers on coveralls and on farm workers, so I use it for one point: gear lowers exposure and never makes spraying safe.
Mixing and Loading
Before you load the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the product label and your manual require for the task. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill or overflow cannot reach a well, a drain or other water. Read the label before you open the container, stand upwind, and do not eat, drink or smoke while you handle pesticides. Never use your mouth to siphon a pesticide from its container. Keep the fill hose above the level of the liquid in the tank so the product cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Use measuring tools kept only for pesticides, never kitchen utensils or food containers. Mix only as much as the job needs so the tank ends empty; do not store leftover mix in the sprayer for later, because it can damage the sprayer’s parts.
Do the mixing and loading well away from the house, children and pets, and keep product in its original container in a locked place away from feed and food.
Children and Pets
Keep children, pets and other people out of the area while you mix, load and spray, and keep them off the treated area for as long as the label says. Before you spray, remove toys and take away or cover pet food and water dishes.
Container Rinsing and Disposal
Follow the product label’s instructions for rinsing the empty container, handling the rinse water and disposing of the container, and rinse only a container the label directs you to rinse. Add rinse water to a spray mixture only when the label permits it and the mixture can take it without exceeding the permitted fill level or changing the label-directed mixture. Never reuse an empty pesticide container for any purpose. For leftover product, follow the label’s disposal steps, or call your state pesticide agency or a household hazardous waste program.
Storage
Before you store the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception. Store pesticides in their original containers, with the label on, locked up or under the control of a person who can keep others away, and out of the reach of children. Never put a pesticide in a container used for food, drink or household products. Keep pesticides away from food, animal feed and protective equipment, and store pesticides and fertilizers apart, because they can react with each other and start a fire. Store the sprayer drained, cleaned and dry, as your manual describes, with the battery stored as the battery manual describes.
If Someone Is Exposed
If someone is exposed to a pesticide, follow the first-aid section of the product label and call Poison Control at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.
Which Printed Figures Fit Which Job
Match the figures to the jobs you have in the next two seasons. My guide to the tank size for battery sprayers helps you choose between 2 and 4 gallons.
- The smallest tank of the four: the PetraTools HD2000-S carries 2 gallons on a shoulder strap and lists no pressure.
- A fixed setting with no dial: the Field King 190515 is pre-set to 40 PSI and holds 4 gallons.
- A dial and a chart: the Field King 190723W prints flow and pressure for each nozzle and dial position, so you can read the chart before you set it.
- Makita batteries already on the shelf: the XSU01Z holds 2.6 gallons and needs a battery and a charger bought separately.
On my long orchard rows I want fewer fill-ups, so tank size is the first figure I check. Whatever you pick, the label of your product and the manual of your sprayer settle the rest.
What to Remember Before You Choose
Start with the shutdown box and the manual of the sprayer you own or plan to buy: they say how to stop it, charge it and which liquids it forbids. Then read any pressure number next to a nozzle, because a printed figure with no nozzle is a pre-set point or a ceiling and never a promise. My tip is to run the first water test from the box in the Field King section and to watch every joint before product goes in. Check what is in the box too, because a tool-only unit needs a battery and a charger bought separately. Judge any 12V vs 18V battery sprayer by its printed tank, pressure, runtime condition and charge time, and let the product label and your manual settle the rest. My picks for the best battery powered backpack sprayer compare seven models by fit and battery.
Frequently Asked Questions
What is a 12V battery sprayer?
A 12V battery sprayer is a sprayer whose maker labels its on-board battery 12V, such as the PetraTools HD2000-S with its 12V 1.3 Ah battery. The label is the maker’s own and does not rank the sprayer against an 18V one. Compare its tank, printed pressure and charge time with the figures of the sprayer you are weighing.
Is a 12V battery sprayer the same as a 12V ATV sprayer?
A 12V battery sprayer is a different machine from a 12V ATV sprayer. The first carries its own rechargeable battery, and the Chapin 97200E ATV unit runs from a vehicle’s 12V supply with no battery or charger in the box. The two share a number and little else, so read the manual of the exact unit.
Which is better for a yard, a 12V or an 18V battery sprayer?
The better sprayer for a yard is the one whose printed tank, pressure and charge figures fit your job. Voltage alone does not decide it, because each maker’s label names only its own battery. A 4 gallon backpack carries twice the liquid of a 2 gallon sling sprayer between fills, and your product label and manual settle the rest.
Does a 12V battery sprayer come with a charger?
A 12V battery sprayer comes with whatever its maker puts in the box, so check the box list. PetraTools lists a charger for the HD2000-S, and Makita sells its 18V XSU01Z as a tool only with no battery or charger. Use only the charger the maker lists for your exact sprayer.
Who makes a 12V battery sprayer?
PetraTools makes the HD2000-S, a 2 gallon sprayer with a 12V rechargeable battery. Chapin sells a 12V vehicle-supply sprayer, the 97200E, that has no battery. Other makers label their batteries differently, such as Field King and Makita at 18V, which is why this page compares printed figures.
References
- Proulx R. Spray Equipment and Calibration. AE73. North Dakota State University Extension; revised October 2025.
- Nuyttens D, Baetens K, De Schampheleire M, Sonck B. Effect of nozzle type, size and pressure on spray droplet characteristics. Biosyst Eng. 2007;97(3):333-345.
- Alheidary MHR. Influence of nozzle type, working pressure, and their interaction on droplets quality using knapsack sprayer. Iraqi J Agric Sci. 2019;50(3).
- Wolf RE. Strategies to Reduce Spray Drift. MF-2444. Kansas State University Agricultural Experiment Station and Cooperative Extension Service; March 2000.
- Occupational Safety and Health Administration. Lithium-ion Battery Safety. Fact Sheet DTSEM FS-4480. US Department of Labor; January 2025.
- Wang G, Ping P, Kong D, et al. Advances and challenges in thermal runaway modeling of lithium-ion batteries. Innovation (Camb). 2024;5(4):100624.
- Garrigou A, Laurent C, Berthet A, et al. Critical review of the role of PPE in the prevention of risks related to agricultural pesticide use. Saf Sci. 2020;123:104527.
Safety Note: Read your sprayer’s manual and the product label before you open any container. The label is the law: it tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftovers and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. This page never gives an amount of product, a dilution or a mixing order: the label does. Wear the protective clothing and equipment the label requires, put it on before you open the container, and wear the eye protection and gloves it names whenever you mix, load, spray, clean the tank or clear a nozzle. Protective equipment lowers your exposure; it does not make spraying safe. Wear every respirator the label requires, of the type it names, and follow the respirator maker’s fit, use and care instructions. Before you clean or store the sprayer, or wire a 12V pump, complete the shutdown below first. Before you mix or load, complete the shutdown below, including its emergency exception. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill cannot reach a well, a drain or other water. Stand upwind, never use your mouth to siphon a product, keep the fill hose above the liquid so it cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Mix only what the job needs, and do not store leftover mix in the sprayer. Never point the wand at yourself, another person or a pet, and never test a spray against your hand. Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Otherwise, before you open the tank, fill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, load, unload, transport, store or leave the sprayer, or lift, put on or take off a backpack unit, complete the shutdown. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Battery sprayer: release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery. 12V vehicle sprayer: first stop and secure the vehicle as its manual directs, then release the trigger, close the wand or boom valve and switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies, and reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the label’s protective equipment while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual, never with your mouth and never by blowing into it. Refit every part and check for leaks with clean water before product goes back in. For the first water test, complete the shutdown first, fill the tank with clean water and close it as your manual directs, connect the power only when you are ready, and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts; complete the shutdown again before you open the tank, fix a leak or add product. Wind, heat and fine droplets carry spray off target: the label may be stricter than any extension guideline, and extension sources give different wind figures, so no single number fits every situation. Do not spray during a temperature inversion, and do not assume that calm air, early morning or evening is suitable. Do not spray just before rain. Keep children, pets and other people out of the area while you spray and off the treated area for as long as the label says, and remove toys and cover pet food and water dishes first. The label’s pollinator wording decides when you may spray around flowering plants, and early morning or evening is not automatically suitable. A sprayer that has held weed killer should stay a weed-killer sprayer: extension services advise a dedicated sprayer, and rinsing may not remove every residue. Follow the product label’s instructions for rinsing empty containers, handling rinse water and disposing of them, and never reuse an empty pesticide container; for leftover product, call your state pesticide agency or a household hazardous waste program, and never pour it down a sink, a toilet or a storm drain. Store pesticides in their original containers, locked up and out of the reach of children, away from food and animal feed, and keep pesticides and fertilizers apart. If someone is exposed, follow the first-aid section of the label, call Poison Control at 1-800-222-1222 and keep the label with you; call 911 in an emergency. If product spills, keep people and animals away and follow the label’s emergency directions; try to contain a small spill only if the label says that is safe and you have the protective equipment it requires, and otherwise get help (the emergency number on the label, Poison Control if anyone is exposed, 911 for a fire, immediate danger or a large spill). Use only the battery and charger the maker supplies or lists for your exact sprayer, charge and store the battery as your manual describes, and do not use a damaged battery or charger: lithium-ion batteries can overheat and catch fire. Wire a 12V pump the way your manual says and use the fuse it lists. On an ATV or UTV, wear the helmet and protective gear the Consumer Product Safety Commission recommends, get hands-on training, sit only in the positions the manufacturer designed, never ride with more passengers than there are seats, and in a UTV fasten the seat belts and keep every part of your body inside the vehicle; stay within the rack and tow capacity in your vehicle’s owner’s manual, and remember that sloshing liquid shifts weight and changes how the vehicle handles; Montana State University Extension advises against riding and spraying if you have to hold a wand or lance. Stop at once, complete the full shutdown and inspect if the sprayer leaks, loses pressure or runs without spraying, and restart only as the manual allows. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, do not handle or remove it: keep people away, follow the battery manual’s emergency instructions, and if it smokes or burns, move away and call 911 or the fire department. Before you fill the tank, complete the shutdown, and fill it only to the level your manual allows. Carrying a full tank is tiring: rest when you are tired.

