PSI on a sprayer stands for pounds per square inch, the unit that measures the pressure of the liquid inside the pump, hose and nozzle. A figure the maker labels maximum is the ceiling of the machine, while other printed pressures belong to a nozzle and a setting, and the nozzle and the product label decide the pressure for a job.
I studied plant protection at the Academy of Applied Studies in Šabac, and that training left me with one habit: ask which nozzle a pressure number belongs to before I trust it. This guide covers what makers print, the ranges extension sources give, and how pressure changes droplets, flow and drift.
What Does PSI Mean on a Sprayer?
PSI measures how hard the liquid is pushed. NDSU Extension says spray pressures on farm sprayers range from near 0 to over 300 pounds per square inch (1). On a garden sprayer the same number shows up in three places, and each one means something different.
Three Numbers, Three Meanings
The maximum pressure is the most the pump may reach. The working pressure is the pressure of the liquid while you spray, shown on a gauge when the sprayer has one. The chart pressure is the figure a nozzle’s maker prints beside a flow rate. Only the working pressure and the chart pressure describe a job. I like to ask of every pressure figure which of these three it is.
A gauge helps only when it reads in a useful range. NDSU says a gauge should have a total range twice the maximum expected reading, and it asks you to check that the gauge is reliable (1). The EGO BSP3500 manual lists no gauge and gives no PSI for the positions of its speed dial, so its dial does not tell you the actual pressure. I recommend treating a reliable gauge as the reading of actual pressure and the nozzle chart as the maker’s stated condition for a flow. I go through the speed dial and the nozzles in my review of EGO’s backpack sprayer.
What Makers Print and What It Tells You
Maker figures for garden sprayer PSI come in different forms, so read each one for what it measures. The table shows three battery backpack models as their makers print the pressure.
| Model | Printed figure | What it describes |
|---|---|---|
| EGO Power+ BSP3500 | Max. Working Pressure 350 psi | The maker’s maximum, in the manual’s own words |
| Makita XSU01Z | Max. working pressure 0.5 MPa; up to 73 PSI on the maker’s page | The maker’s maximum; the manual also prints about 0.34 MPa with its vertical 2-head nozzle and about 0.12 MPa with its weedkiller nozzle |
| DEWALT DXSP190681 | 3 to 77 psi, by nozzle and dial position, on water or a similar liquid and may vary about 10% | A nozzle flow chart; the manual prints no single maximum |
DEWALT says a wrong nozzle and dial pairing can damage the pump, and its chart figures are for water or a similar liquid and may vary about 10%. My review of DEWALT’s backpack sprayer sets that chart in the context of the whole kit.
A Printed Maximum Is a Ceiling
These three figures come from three manuals and describe three different things, so they do not rank the sprayers. A maximum is the limit of the pump. The DEWALT chart shows how the working pressure follows the nozzle and the dial: according to DEWALT, positions 1 to 3 work off a low pressure cutoff and positions 4 to 10 work off a high pressure cutoff. I find the chart more useful than the maximum, because it tells me what the sprayer does with the nozzle in my hand.
Pressure and Nozzle
A sprayer’s maximum pressure is the limit of the machine, not a setting to aim for. The product label and the nozzle’s maker decide the pressure and the nozzle for a job. Higher pressure makes more fine droplets that drift, and the nozzle you choose changes the droplet size.
Pressure Ranges by Job From Extension Sources
Extension services publish pressure ranges for spraying, and their figures differ because they describe different nozzles and jobs. NDSU and K-State write for farm and boom sprayers, and LSU AgCenter covers drift on field equipment, so treat every figure below as background and never as the setting for a backpack wand (1) (2).
| Source | Figure | Applies to |
|---|---|---|
| NDSU Extension | 15 to 40 PSI may be sufficient for most herbicides or fertilizer; up to 400 PSI or more may be needed for insecticides or fungicides | General guidance for farm sprayers |
| NDSU Extension | Extended range flat fan nozzles operate over 15 to 60 PSI; flood fan nozzles reduce drift best at 10 to 25 PSI | By nozzle type |
| LSU AgCenter | Flat fan nozzles can operate at 30 to 50 PSI; low-drift nozzles at 20 PSI | Drift management guidance |
| K-State Extension | Refrain from pressures above 40 to 45 psi; 30 to 40 psi is a normal level for foliar herbicides | Field herbicide sprayers |
NDSU’s 15 to 40 PSI for most herbicides and fertilizer sits near K-State’s advice to stay under 40 to 45 psi, while LSU’s flat fan range of 30 to 50 PSI reaches higher. The product label wins over all of them, and so does the nozzle maker’s chart. I treat the label as the final word on pressure, ahead of every extension figure. I use these ranges to judge whether a chart looks reasonable, and the chart itself to choose the pressure. I explain the flat fan pattern in my guide to fan spray nozzles.
Why Higher PSI Means More Fine Droplets
Pressure changes droplet size, and droplet size decides how far spray travels on the air. K-State says droplets over about 150 microns resist evaporation far better than smaller ones, and that higher pressures make many more droplets under 100 microns (2). LSU AgCenter calls droplet size the overwhelming factor in drift and treats droplets under 150 micrometers as drift-prone.
What the Test Benches Found
A test rig measured 32 combinations of nozzle type, size and pressure and found that all three change droplet size and velocity (3). It used agricultural boom nozzles in a climate room, so it shows the pattern, and no yard wand took part in it. Droplet size and drift get their own page in my guide to spray nozzle types.
In a wind tunnel, drift-reducing nozzle designs gave larger droplets and far fewer droplets of 100 micrometers or less than standard flat fans (4). That test used five boom nozzles with water and a surfactant.
One bench test used a knapsack sprayer with six nozzle types at 15 and 25 psi. The hollow cone nozzle gave the highest coverage, and an air-induction flat fan gave the largest droplets (5). It was a single university experiment with a tracer on cards, so it describes those nozzles on that bench. I read droplet size first when I judge a spray pattern, because droplet size is what the wind acts on. I describe the hollow and full cone types in my guide to cone spray nozzles.
Wind and Drift
Wind and Drift
Drift is spray carried off target by the air, and wind speed is the factor extension sources stress most. Their figures differ and none fits every situation, and your product label may be stricter than all of them. K-State Extension suggests spraying when the wind is under 10.1 miles per hour and says there is no maximum wind speed that fits every situation. LSU AgCenter says to avoid applying when the wind is above about 10 miles per hour. NC State says under 5 miles per hour when you calibrate with the product in the tank. Cornell gives no number and says not to take a chance by spraying in the wind. Do not spray during a temperature inversion, when cool air near the ground holds small droplets in the air, and do not assume that calm air, early morning or evening is suitable: check the actual conditions and follow every weather restriction on the product label. High temperature and low humidity make spray evaporate faster. Do not spray just before rain. Droplets smaller than about 150 micrometers drift most easily, and higher pressure makes more of them.
PSI Does Not Set How Much You Spray
Pressure and flow are linked by a rule, and doubling a nozzle’s rate takes four times the pressure: NDSU says that to double the spray rate from a nozzle, the pressure must go up by a factor of four (1). NDSU adds that pressure above the nozzle maker’s recommendation raises the delivery rate, shrinks the droplets and can distort the spray pattern, which can cause excess drift and uneven coverage.
Reading a Nozzle Chart
A nozzle chart lists a flow in gallons per minute at a stated pressure. NDSU says to always follow the pressure recommendations of nozzle manufacturers, and that lower pressures produce larger droplets, which reduces drift potential (1). Higher pressures make small drops that NDSU says give maximum plant coverage but are more susceptible to drift.
The numbers on a tip therefore go with a flow at a stated pressure, and one maker’s codes differ from another’s. The nozzle maker’s own chart decides what a tip does at the pressure your sprayer delivers. The sprayer’s own output is a separate measurement that calibration with clean water gives you, and no PSI figure replaces that step. I keep the nozzle chart next to the manual, because the two documents answer different questions. I show the clean-water method step by step in my guide to calibrating a backpack sprayer.
Gauges, Regulators and Constant Pressure
A gauge shows the pressure, and a regulator holds it steady. The two parts do different jobs, and your exact model’s manual says which of them it carries.
NC State Extension says most backpack sprayers have pressure regulators that deliver the spray mix at a constant pressure, and that these devices must be kept in good order because a consistent application needs a constant pressure. The maker’s manual states whether a given battery sprayer has a regulator. According to DEWALT, its DXSP190681 backpack keeps flow rate constant regardless of battery depletion state. My comparison of battery and manual backpack sprayers shows what a powered pump changes in daily use.
Pump Sprayer PSI
A hand-pump sprayer has no motor to hold a pressure. NC State says few handheld sprayers contain pressure regulators, and that pump sprayer PSI stays fairly even only if the hand pump is operated at a constant number of strokes per minute. I weigh the motor against the hand pump in my comparison of battery and pump sprayers.
Cornell’s pesticide safety program estimates that 13% of sprayers have inaccurate pressure gauges, a figure that comes from field sprayers. I take that as a reason to check a gauge reading against the pressure the nozzle chart states.
Reading PSI Before You Spray
Reading PSI becomes hands-on work the moment you change a nozzle to match a chart or run the first water test, so the full shutdown comes first.
Full Shutdown Before Any Hands-On Step
Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Shutdown before you open the tank, fill or refill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, move, store or leave the sprayer. Never point the wand at yourself, another person or a pet. During normal spraying, move only as the equipment manuals and the product label permit; walking while spraying with a backpack unit, or driving a mounted boom at the spraying speed its manual describes, is operation, not transport. Never ride while operating a hand-held wand or lance. Battery sprayer (handheld or backpack): release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery and keep it away from the sprayer. Wear the protective equipment the product label requires while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual; never clear a nozzle with your mouth and never by blowing into it. Add every step your manual gives, in its order. Refit every part, close the lid and check for leaks with clean water before product goes back in.
Before you open or fill the tank, complete the full shutdown in the shutdown box. Then fill only to the level your manual allows and, for a carried sprayer, only to a weight you can handle with the straps and hip belt adjusted as the manual describes. Before you lift, put on or take off a backpack unit, or load, unload, transport or leave the sprayer, complete the full shutdown again. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Carrying a full tank is tiring work: rest when you are tired, and stop before you lose your footing.
Before the first water test, complete the full shutdown in the shutdown box, then fill the tank with clean water and close the lid as your manual directs. Connect the power (install the battery) only when you are ready to test. Run the sprayer and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts. Before you open the tank, correct a leak or add product, complete the full shutdown again. Before every use, check the tank, strainer, hose and nozzle, and fix any leak before product goes in. Follow your manual’s first-use steps.
My own rule on a new sprayer is to do the water test before any product goes near the tank. A leak found at that stage costs only clean water.
Pesticide Safety Basics
Many sprayers put pesticides on plants, and a pesticide label is a legal document. These points apply to any pressure setting. I keep the label open beside the sprayer’s manual whenever a product is involved. If pesticide work is your main use, my list of battery sprayers for pesticides sorts the models by tank and battery.
- The label: The product label is the law. It tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftover product and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. Your sprayer’s manual does not replace the label, and the label does not replace the manual: read the label before you open the container, and follow both.
- Protective equipment: Wear the protective clothing and equipment the product label requires, and put it on before you open the container. Wear the eye protection and gloves the label names every time you mix, load, spray, clean the tank or clear a nozzle. Cornell’s pesticide safety program also advises chemical-resistant gloves, goggles and a respirator when you handle moderately toxic products, even when the label does not call for them. Wear every respirator the label requires, of the type the label names, and follow the respirator maker’s instructions for fit, use and care. If you follow Cornell’s advice and wear one the label does not require, or if it is unclear which respirator or filter is right, get qualified guidance on the respirator and filter before you handle the product. Protective equipment lowers your exposure; it does not make spraying safe. A critical review of coveralls worn by agricultural pesticide handlers found that the real-world protection from protective equipment may be over-estimated (6).
- Amounts: The product label, not this page, gives the amount of product, the dilution and the mixing order, so read it before you mix. Do not combine products unless the mixture complies with every product’s label and its compatibility has been established through the manufacturers or a qualified pesticide specialist; nobody’s advice overrides a label prohibition.
- Mixing and loading: Before you load the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the product label and your manual require for the task. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill or overflow cannot reach a well, a drain or other water. Read the label before you open the container, stand upwind, and do not eat, drink or smoke while you handle pesticides. Never use your mouth to siphon a pesticide from its container. Keep the fill hose above the level of the liquid in the tank so the product cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Use measuring tools kept only for pesticides, never kitchen utensils or food containers. Mix only as much as the job needs so the tank ends empty; do not store leftover mix in the sprayer for later, because it can damage the sprayer’s parts.
- Children and pets: Keep children, pets and other people out of the area while you mix, load and spray, and keep them off the treated area for as long as the label says. Before you spray, remove toys and take away or cover pet food and water dishes.
- Empty containers: Follow the product label’s instructions for rinsing the empty container, handling the rinse water and disposing of the container, and rinse only a container the label directs you to rinse. Add rinse water to a spray mixture only when the label permits it and the mixture can take it without exceeding the permitted fill level or changing the label-directed mixture. Never reuse an empty pesticide container for any purpose. For leftover product, follow the label’s disposal steps, or call your state pesticide agency or a household hazardous waste program.
- Cleaning: Before you clean the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the label and your manual require. Clean the sprayer as soon as you can after use, because dried product is harder to remove than product still in solution. Empty the tank, rinse the tank, hose, wand and nozzle, and clean the strainers and screens, following the product label and your manual; extension guidance warns that water alone may not remove every product. Clean it away from desirable plants, wells and other water, and wash the outside. Do not pour leftover product or rinse water down a sink, a toilet or a storm drain, or onto bare ground.
- Dedicated sprayer: Illinois Extension advises a dedicated sprayer for the home orchard, one that has never been used for weed control products. Penn State and Iowa State warn that even small amounts of herbicide left in tanks, hoses, screens and fittings can harm crops, and that water alone is generally not enough to remove pesticide residue. Treat a sprayer that has held weed killer as a weed-killer sprayer, and keep a separate one for fruit trees, vegetables, ornamentals and liquid fertilizer.
- Battery and charger: Use only the battery and charger the maker supplies or lists for your exact sprayer, and charge, store and handle the battery only as your manual describes. To change or charge a battery, first complete the full shutdown in the shutdown box, including its emergency exception, which ends with removing the battery; begin the change or the charging only after that. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger, and follow the manual’s directions if a battery or charger gets wet. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using it without handling or removing it, keep people away and follow the battery manual’s emergency instructions; if it smokes or burns, move away and call 911 or the fire department.
- Storage: Before you store the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception. Store pesticides in their original containers, with the label on, locked up or under the control of a person who can keep others away, and out of the reach of children. Never put a pesticide in a container used for food, drink or household products. Keep pesticides away from food, animal feed and protective equipment, and store pesticides and fertilizers apart, because they can react with each other and start a fire. Store the sprayer drained, cleaned and dry, as your manual describes, with the battery stored as the battery manual describes.
If Someone Is Exposed
If someone is exposed to a pesticide, follow the first-aid section of the product label and call Poison Control (America’s Poison Centers) at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.
Putting the Number to Work
Three points carry this guide: PSI is pounds per square inch, a printed maximum is the limit of the machine, and the nozzle chart and the product label decide the pressure for a job. My tip: write the chart pressure for your nozzle on a strip of tape near the handle, so it is in front of you each time the nozzle changes. Next, I recommend reading your sprayer’s manual for its nozzle chart and dial positions, then the label of the product you plan to use. PSI on a sprayer is a number to read against those two documents and never a figure to push to its limit. My list of battery powered backpack sprayers compares seven models by fit and battery.
Frequently Asked Questions
What does PSI mean on a sprayer nozzle?
On a sprayer nozzle, PSI is the pressure, in pounds per square inch, of the liquid pushed through the nozzle opening. A nozzle’s maker prints a flow at a stated PSI, and NDSU says to always follow the nozzle maker’s pressure recommendations. Pressure above that recommendation raises the delivery rate and makes smaller droplets.
What is full form PSI?
The full form of PSI is pounds per square inch, a unit of pressure. On a sprayer it describes how hard the liquid is pushed through the pump, hose and nozzle. NDSU Extension lists the abbreviation beside GPM for gallons per minute.
What do the numbers on spray nozzles mean?
The numbers on a spray nozzle tip are a maker’s code that goes with a flow rate at a stated pressure. Codes differ between makers, so the nozzle’s own chart decides what a number means. NDSU says to always follow the nozzle maker’s pressure recommendations.
What is a pressure regulator on a sprayer?
A pressure regulator on a sprayer is a part that delivers the spray mix at a constant pressure, according to NC State Extension, which says most backpack sprayers have one. NC State adds that few handheld sprayers do and that a regulator must be kept in good order. The maker’s manual says whether your sprayer has one.
Does a higher PSI mean a sprayer puts out more liquid?
A higher PSI makes a nozzle put out more liquid, though slowly: NDSU says the pressure must go up by a factor of four to double a nozzle’s spray rate. Pressure above the nozzle maker’s recommendation also makes smaller droplets and can distort the pattern. The sprayer’s own output comes from calibration with clean water.
References
- Proulx R. Spray Equipment and Calibration. AE73. North Dakota State University Extension; revised October 2025.
- Wolf RE. Strategies to Reduce Spray Drift. MF-2444. Kansas State University Agricultural Experiment Station and Cooperative Extension Service; March 2000.
- Nuyttens D, Baetens K, De Schampheleire M, Sonck B. Effect of nozzle type, size and pressure on spray droplet characteristics. Biosyst Eng. 2007;97(3):333-345.
- McGinty J, Baumann P, Hoffmann W, Fritz B. Evaluation of the spray droplet size spectra of drift-reducing agricultural spray nozzle designs. Am J Exp Agric. 2016;11(3):1-5.
- Alheidary MHR. Influence of nozzle type, working pressure, and their interaction on droplets quality using knapsack sprayer. Iraqi J Agric Sci. 2019;50(3).
- Garrigou A, Laurent C, Berthet A, et al. Critical review of the role of PPE in the prevention of risks related to agricultural pesticide use. Saf Sci. 2020;123:104527.
Safety Note: Read your sprayer’s manual and the product label before you open any container. The label is the law: it tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftovers and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. This page never gives an amount of product, a dilution or a mixing order: the label does. Wear the protective clothing and equipment the label requires, put it on before you open the container, and wear the eye protection and gloves it names whenever you mix, load, spray, clean the tank or clear a nozzle. Protective equipment lowers your exposure; it does not make spraying safe. Wear every respirator the label requires, of the type it names, and follow the respirator maker’s fit, use and care instructions. Before you clean or store the sprayer, or wire a 12V pump, complete the shutdown below first. Before you mix or load, complete the shutdown below, including its emergency exception. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill cannot reach a well, a drain or other water. Stand upwind, never use your mouth to siphon a product, keep the fill hose above the liquid so it cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Mix only what the job needs, and do not store leftover mix in the sprayer. Never point the wand at yourself, another person or a pet, and never test a spray against your hand. Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Otherwise, before you open the tank, fill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, load, unload, transport, store or leave the sprayer, or lift, put on or take off a backpack unit, complete the shutdown. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Battery sprayer: release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery. 12V vehicle sprayer: first stop and secure the vehicle as its manual directs, then release the trigger, close the wand or boom valve and switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies, and reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the label’s protective equipment while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual, never with your mouth and never by blowing into it. Refit every part and check for leaks with clean water before product goes back in. For the first water test, complete the shutdown first, fill the tank with clean water and close it as your manual directs, connect the power only when you are ready, and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts; complete the shutdown again before you open the tank, fix a leak or add product. Wind, heat and fine droplets carry spray off target: the label may be stricter than any extension guideline, and extension sources give different wind figures, so no single number fits every situation. Do not spray during a temperature inversion, and do not assume that calm air, early morning or evening is suitable. Do not spray just before rain. Keep children, pets and other people out of the area while you spray and off the treated area for as long as the label says, and remove toys and cover pet food and water dishes first. The label’s pollinator wording decides when you may spray around flowering plants, and early morning or evening is not automatically suitable. A sprayer that has held weed killer should stay a weed-killer sprayer: extension services advise a dedicated sprayer, and rinsing may not remove every residue. Follow the product label’s instructions for rinsing empty containers, handling rinse water and disposing of them, and never reuse an empty pesticide container; for leftover product, call your state pesticide agency or a household hazardous waste program, and never pour it down a sink, a toilet or a storm drain. Store pesticides in their original containers, locked up and out of the reach of children, away from food and animal feed, and keep pesticides and fertilizers apart. If someone is exposed, follow the first-aid section of the label, call Poison Control at 1-800-222-1222 and keep the label with you; call 911 in an emergency. If product spills, keep people and animals away and follow the label’s emergency directions; try to contain a small spill only if the label says that is safe and you have the protective equipment it requires, and otherwise get help (the emergency number on the label, Poison Control if anyone is exposed, 911 for a fire, immediate danger or a large spill). Use only the battery and charger the maker supplies or lists for your exact sprayer, charge and store the battery as your manual describes, and do not use a damaged battery or charger: lithium-ion batteries can overheat and catch fire. Wire a 12V pump the way your manual says and use the fuse it lists. On an ATV or UTV, wear the helmet and protective gear the Consumer Product Safety Commission recommends, get hands-on training, sit only in the positions the manufacturer designed, never ride with more passengers than there are seats, and in a UTV fasten the seat belts and keep every part of your body inside the vehicle; stay within the rack and tow capacity in your vehicle’s owner’s manual, and remember that sloshing liquid shifts weight and changes how the vehicle handles; Montana State University Extension advises against riding and spraying if you have to hold a wand or lance. Stop at once, complete the full shutdown and inspect if the sprayer leaks, loses pressure or runs without spraying, and restart only as the manual allows. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, do not handle or remove it: keep people away, follow the battery manual’s emergency instructions, and if it smokes or burns, move away and call 911 or the fire department. Before you fill the tank, complete the shutdown, and fill it only to the level your manual allows. Carrying a full tank is tiring: rest when you are tired.

