A man inspecting the impeller mechanism under a broadcast spreader on a garage floor

What Is a Spreader Impeller? Parts, Types and How It Throws Granules

A spreader impeller is the spinning plate under a broadcast spreader’s hopper that flings granules out in a wide fan. Every broadcast spreader has one, and its condition and angle change where the product lands. In my large-scale production work I verified seed drill calibration on weighing trays, so I pay close attention to the one part that sends product off the machine. Below I cover what the impeller is, how it gets its spin, the types makers describe, what changes its throw and how to handle it safely.

What Is a Spreader Impeller?

The impeller is the spinning disc or plate directly below the hopper’s gate. Product drops from the open gate onto it, and the fins or vanes on its surface fling the granules outward. Kentucky Extension describes rotary spreaders the same way: they “distribute material through centrifugal force”. EarthWay’s patent filing words it as “an impeller directly below the shut-off plate that spins and thus distributes granules falling on the impeller”, and adds that each impeller has “upstanding fins” that fling the granules. I cover the hopper, the gate and the throw of the whole machine in what a broadcast spreader is.

Same Part, Different Names

Makers do not agree on the word. EarthWay, Brinly, Chapin, Agri-Fab and SOLO all print “impeller” in their manuals, Brinly’s tips also call it a “spinner blade”, and the Scotts EdgeGuard DLX guide labels the same part a “Rotary Disk”. NC State Extension and the hand-crank study by Wolf and Smith say “spinner” for the small units. I use impeller in this guide because EarthWay, Brinly, Chapin, Agri-Fab and SOLO print it, and I treat every one of those names as the same job: the part that turns and throws.

Which Spreaders Have One

Walk-behind rotary spreaders, tow-behind rotary spreaders and hand-crank or battery handheld spreaders all carry a spinning plate. A drop spreader does not. NC State Extension says its gate lets product fall straight down through ports between the wheels, so there is nothing to throw it sideways. If you are choosing between the two delivery styles, the impeller is the dividing line, and I recommend deciding on the job you have, not on the part count. I set the two delivery styles side by side in broadcast and drop spreaders.

How the Impeller Fits in the Spreader

The impeller on a spreader sits low in the machine, between the gate above it and the ground below. The hopper holds the product, the gate or shut-off plate meters it onto the plate, and the drive underneath keeps the plate turning. The table lists what sits around it and what makers call each part. I describe the hopper on its own, with its materials and care, in what a spreader hopper is.

Parts around the impeller, as manuals and guides name them
Part Where it sits What makers print
Hopper Above the gate Poly hopper, hopper screen, cover on some models
Gate Between hopper and plate Shut-off plate (EarthWay, Brinly), trigger (Scotts), rotary gate (Chapin)
Impeller Directly below the gate Impeller, spinner blade, Rotary Disk
Gearbox and shaft Below the plate, on the axle Gearbox and axle assembly (Brinly), enclosed gearbox (EarthWay, Chapin)
Deflector or edge control Beside the plate EdgeGuard (Scotts), deflector shield (Brinly, SOLO)

The Parts Beside the Plate

Some models add a part that blocks one side of the throw. I explain how those edge guards and side controls work in what a spreader deflector is.

According to Scotts, the EdgeGuard lever “blocks off the right side of the spreader pattern”. Brinly says its deflector “will keep material from moving towards left side of hopper”, and SOLO says its deflector shield changes the width of spread. Those are the makers’ printed purposes. What the part does on your lawn is your result, so I check the area beside the plate before I trust any deflector. My Scotts EdgeGuard DLX spreader review covers that lever in detail.

What the Gate Does

The gate does not throw anything. It opens and closes the flow onto the plate, and the lever or trigger that works it is the control you reach for first. I keep that distinction clear because a stuck gate and a worn plate are two different problems with two different fixes. I follow the product from the hopper through the gate to the ground in “how a broadcast spreader works”.

How an Impeller Gets Its Spin

There are three ways to turn the plate: a wheel on the ground, a hand crank or a small motor. The drive matters because it ties the plate’s speed to something you control.

Ground-Driven Push and Tow-Behind Units

On a push spreader or a tow-behind spreader, the wheels turn a gearbox on the axle, and the gearbox turns the impeller. My “push against tow behind spreader” comparison covers the hopper, hitch and safety differences.

EarthWay’s manual says a gearbox on the axle drives the impeller and that it “must turn clockwise when pushing forward”. Chapin’s manual says its gearbox “runs counterclockwise when viewed from above”. Agri-Fab’s tow-behind manual says the drive wheel and large gear positions “determine which direction the impeller will spin”. The direction is the maker’s design, so read the line in your own manual. I trace the wheel, the gears and the hitch on a tow-behind model in “how a tow-behind spreader works”.

NC State Extension adds a practical point: generally only one wheel drives the impeller, and continuing to spread while turning changes the impeller’s speed and the distribution pattern. That is why the gate closes before every stop and turn.

Gate at Stops and Turns

Close the gate before you stop, before you slow down to turn, and whenever you pause, and open it again only after you are walking or driving at the steady pace your manual describes. Do not spread while you turn.

Hand-Crank Units

A hand-crank spreader steps up your arm’s motion through gears. SOLO’s manual says each complete revolution of the crank handle turns the impeller 7 1/2 times, which is a gear ratio and says nothing about how much product leaves. SOLO also prints a caution to keep hands away from the rotating impeller.

Battery Handhelds

A battery handheld replaces the crank with a small motor. How the battery and charger work is each model’s own manual, and the safety section below carries the battery lines. I compare the battery model with a crank handheld in battery powered and handheld spreaders.

How named models turn the impeller, in the makers’ words
Spreader Drive Manual line
EarthWay 2600A-Plus Axle gearbox Impeller must turn clockwise when pushing forward
Brinly P20-500BHDF-A Gearbox and axle assembly Fan speed follows the speed at which you operate it
Chapin 8400C SureSpread Axle gearbox Gearbox runs counterclockwise when viewed from above
Agri-Fab 45-0463 tow-behind Axle and gear assembly Wheel and gear positions set the impeller’s direction
SOLO 421 chest-mount Hand crank 7 1/2 impeller turns per crank revolution

Types of Impellers as Makers Describe Them

Makers describe a few shapes, and none ranks one above another. I recommend reading them as design choices that belong to a model, not as a grade.

Single Disc With Fins

SOLO’s chest-mount spreader has a fan-finned impeller disc in a ribbed housing. EarthWay’s earlier manual edition refers to the “impeller blades”, and Brinly’s tips refer to the “spinner blade”. Each of these is one turning part with raised surfaces that engage the granules. My SOLO 421 chest-mount spreader review covers that chest-mount model in full.

Single Plate on a Shaft

The Scotts EdgeGuard DLX has a Rotary Disk, and the Chapin 8400C shows an impeller plate under the hopper with an enclosed gearbox on the axle. Chapin’s manual lists the impeller as fitted to the gearbox and then to the gearbox shaft, with a marking for the direction.

Dual and Twin Impellers

EarthWay’s patent filing describes a spreader with a pair of impellers that spin in opposite directions, and says the single impeller “limits the amount of granules that may be distributed”. Those are the maker’s statements about its own design. A study of single and twin-disc tractor-mounted fertilizer spreaders found that side-to-side tilt changed the pattern for both designs (1).

What Changes How an Impeller Throws

No impeller guarantees an even pattern. A field study of commercial spinner and pneumatic spreaders found that spreaders differ widely in how evenly they spread, and that spreader type did not appear to decide it (2). A few things are known to move the throw. My separate guide covers what skews a broadcast pattern on a rotary model.

A Level Impeller

A rotary spreader that is tilted throws a different pattern. The twin-disc study above, which tested tractor-mounted farm spreaders, compared angles against a level position and found the angle had a significant effect (1). NC State Extension says to hold the handle at the same height used in calibration because the impeller should be level, and Brinly’s tips say to keep the impeller level when spreading. I treat level as the first thing to look at when a pattern looks lopsided.

Build-Up and Humid Air

A laboratory test of rotary turf spreaders found that when humidity rises above a fertilizer’s critical level, the material’s friction on the impeller changes and the pattern skews, and that materials with insoluble parts build up on the impeller and gradually shift the pattern (3). Brinly’s tips say excess material build-up can cause an uneven spread pattern, and EarthWay’s manual says wet fertilizer changes the spread pattern and the flow. I recommend reading the cleaning section below before you wash the plate, because that step needs the safe-state steps first.

Pace and Turns

Because a ground-driven impeller follows the wheels, your pace changes its speed. A laboratory test of one rotary turf spreader with a ground-driven impeller found that the application rate changed significantly with a modest drop in speed or a small rise, and the author cautions that it tested one material and one spreader (4). Brinly’s manual says fan speed follows the speed at which you operate it. Keep the pace your manual describes.

How a Hand-Crank Unit Is Carried

On a hand-crank spreader the plate is in front of you, so how you carry it matters. A study of a hand-operated spinning spreader found that the widest swath and the most uniform distribution came when the spinner was carried directly in front of the operator and the crank slightly to the right, and that a non-uniform pattern came with the spinner to the left (5). It is one small study of one design, so I use it for the idea that carrying position changes the pattern and nothing more. In my guide to what a handheld spreader is, I explain how it works and which kind to pick.

Impeller Safety and Handling

A turning plate can injure a hand, a finger or loose clothing, and it throws product that can be a lawn chemical. SOLO’s manual prints the line plainly: keep hands away from the rotating impeller.

Safe-State Box: Stop and Make Safe

Emergency first, for a spreader with a battery: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the spreader without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine steps. Stop and make safe before you fill or unload the hopper, reach into the hopper, clear a clog, clean or rinse the spreader, lubricate it, adjust the gate or the pattern, change a part, hitch or unhitch it, charge or change a battery, move it, store it or leave it. Keep your hands, feet, hair and loose clothing away from the impeller, the plate, the agitator, the gears and the wheels while anything can turn. During normal spreading, walk or drive only as your manual and the product label permit; walking behind a push spreader, or pulling a tow-behind unit at the speed its manual describes, is operation, not transport. Walk-behind or hand-crank spreader: close the gate, then stop walking or cranking, and wait until the impeller, plate, agitator and wheels have stopped turning. Tow-behind spreader: close the gate, stop the vehicle, set the parking brake, switch the engine off and remove the key as the vehicle’s manual says, and wait until the wheels, impeller and agitator have stopped turning, before you reach into the hopper or touch the impeller. Battery spreader: release the trigger or close the gate as your manual directs, switch the spreader off, wait until all moving parts have stopped, then remove the battery as the manual directs (on a model with a built-in battery that cannot be removed, such as the WORKPRO X, follow that manual’s own off and storage steps instead, and never open the battery compartment) and keep a removed battery away from the spreader while you work. Follow any additional isolation steps in the exact manual. Keep the gate closed while you fill. Wear all the protective equipment the product label and your manual require while you fill, clean or clear a jam. Clear a clog only with the method in your exact manual. Follow every applicable safety step in your manual, in the order it specifies. Refit every guard and cover, and check that the gate opens and closes before product goes back in.

Never push, kick or dig product out of the gate or off the plate while anything can turn. If product clumps or bridges in the hopper or the gate clogs, stop and complete the stop and make-safe steps in the safe-state box first, then clear it only with the method in your manual. If the plate wobbles or stops, a gear grinds or a wheel locks, stop and complete the same steps, inspect, and go on only on the conditions your manual gives.

Tow-Behind Units

Follow your towing vehicle’s owner’s manual and the spreader’s own manual for hitching, turning, slopes, speed and load limits, and stay within the tow capacity in the vehicle’s owner’s manual. Never ride on a spreader or carry a passenger on it. Turn only as the two manuals direct, and keep children and pets well clear of the vehicle and the spreader while you load, hitch and spread. Before you fill, hitch, unhitch, reach into the hopper or touch the impeller, complete the tow-behind steps in the safe-state box.

Agri-Fab’s tow-behind manual says not to allow anyone to ride or sit on the spreader attachment frame, and Brinly’s push spreader manual says not to let anyone sit or ride on the equipment during operation.

Battery Models

Use only the batteries the maker specifies for your exact spreader, and charge, store and handle them only as your manual describes. Recharge rechargeable batteries only with a charger the manual approves, and never recharge disposable cells. Before you fill the hopper, clear a jam, clean the spreader or change the battery, follow the emergency exception and the applicable stop and make-safe steps in the safe-state box. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using it without handling or removing it, keep people away and follow the battery manual’s emergency instructions; if it smokes or burns, move away and call 911 or the fire department.

The Product in the Hopper

The impeller throws whatever the hopper holds, and rotary spreaders throw past the edge of the lawn. UC IPM advises drop spreaders rather than rotary spreaders to avoid off-target fertilizer application, and Kentucky Extension says drop spreaders reduce off-target application on beds, sidewalks and driveways. These are the reader tips I give for the product:

  • Label first: Read the product label before you open the bag. Follow its directions for the permitted use, the application amount, protective equipment, weather, watering in, access by people and pets, storage and disposal. Using a registered pesticide in a way its label does not allow is against federal law. Follow the spreader’s manual too. If the product’s instructions and the spreader’s instructions cannot both be followed, do not use that combination; ask the manufacturers for guidance.
  • Protective equipment: Wear all the protective equipment the product label and your spreader’s manual require, and put it on before you open the bag. Wear it every time you fill the hopper, clean the spreader or clear a clog. Protective equipment lowers your exposure; it does not make handling a lawn product safe.
  • Model requirements: SOLO’s manual says to wear safety glasses or eye shields, closed-toed shoes with good traction, snug long-sleeved clothes, tightly cuffed or cuffless pants and non-slip gloves, to tie long hair back, and, when spreading chemicals, to wear protective clothing, a respirator and eye protection. Brinly’s manual says to wear eye protection, substantial footwear and long trousers, and to avoid loose clothing. Agri-Fab’s tow-behind manual says to wear eye and hand protection when handling and applying lawn or garden chemicals, and substantial footwear when you operate the tractor and spreader. Those lines belong to those models, so read your own manual.
  • Hygiene for pesticide-containing products: Wash your hands before eating, drinking, smoking or using the restroom when you work with pesticides. Change your clothes and wash your hands immediately after you apply a product that contains a pesticide, and follow the label’s additional washing and clothing instructions.
  • Filling: Before you fill or unload the hopper, complete the stop and make-safe steps for your spreader in the safe-state box, and keep the gate closed. For fertilizer, fill on a hard surface where spilled granules can be swept up, away from drains and water. Follow the product label’s handling and ventilation directions, and wear all the protective equipment the label and your manual require. Fill only to the level your manual allows, and secure the hopper cover or lid if your spreader has one. Keep children and pets away, and never leave a filled spreader where they can reach it.
  • Spills: Keep people and pets away from a spill. Follow the product label and its safety data sheet for collecting, reusing and disposing of spilled product, and wear the protective equipment they require. Never hose or wash granules into a street, a gutter, a drain, a ditch or water, and do not pile spilled product onto the lawn or return contaminated material to the bag. If you cannot manage the spill safely, stay away and call the emergency number on the label.
  • Runoff: Keep fertilizer off pavement and out of drains and surface water. If scattered plain fertilizer lands on a sidewalk, a driveway or a patio, sweep it back onto the lawn before you water, without going over the label rate; collect a concentrated spill instead. For pesticide granules, follow the label’s cleanup instructions. Follow any buffer requirement that applies and keep fertilizer out of those areas. EPA advises against fertilizing before windy or rainy days, and Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Follow the product’s weather and watering directions too.
  • Children and pets: Keep children, pets and other people away from the area while you fill and spread, and keep them off the treated area for as long as the label says. Store the bag and the filled spreader where they cannot reach them.
  • Storage: Before you store the spreader, complete the stop and make-safe steps in the safe-state box. Store it empty, clean and dry, as your manual describes, with the gate closed. Keep products in their original labeled containers, securely closed, under the storage conditions their labels give, and away from children and pets. Lock pesticides away, apart from fertilizer, food and animal feed, and never put any product into a food or drink container. Store a battery as the battery manual describes.
  • Exposure: If someone swallows or is exposed to a lawn product, follow the first-aid section of the product label and call Poison Control (America’s Poison Centers) at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.

Settings Belong to the Label

The product label gives the application directions, so read it before you set the gate. A setting listed for your exact spreader and product is a starting point, not proof of the amount delivered: follow the spreader’s manual and calibrate for the product, the spreader and the person using it before you apply. Never exceed the label’s application rate.

Cleaning, Wear and Replacement Parts

Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above. NC State Extension says to wash the spreader after each day’s use to avoid buildup around the ports and on the impeller, to dry it completely to prevent rusting, and to lubricate it as the owner’s manual specifies.

Washing and Drying

Before you clean the spreader, complete the stop and make-safe steps in the safe-state box, and wear the protective equipment the product label and your manual require. Handle leftover product, cleaning water and residues as the product label directs. Clean the spreader only by a method both the label and the manual permit, and rinse it only where they permit it, keeping product and contaminated wash water out of drains and water supplies. Dry the spreader completely, and lubricate it as its manual directs.

If you change products, follow both products’ cleaning requirements: a rinse alone does not show that all residue is gone.

Replacement Parts

Manuals treat the impeller as a part that can be replaced. Chapin’s parts list names the impeller, gearbox, drive shaft and gate control as separate items, and Agri-Fab’s manuals list a spreader impeller among the parts. I recommend using the maker’s part for your exact model and fitting it as your manual shows, with the same stop and make-safe steps first, because the plate has to turn the direction the gearbox expects.

Impeller, Agitator and Gate Compared

Three parts get mixed up. The gate opens and closes the flow, the agitator turns inside the hopper above the gate, and the impeller sits below the gate and throws the product. The Scotts guide labels its agitator “inside hopper” and its Rotary Disk separately, and Chapin’s manual calls its hopper part an auger. My guide to what a spreader agitator is explains the part and the different names manufacturers use for it.

What to Remember About the Impeller

Three things matter most. The impeller is the plate under the gate that throws the product, your manual names its direction and its replacement part, and a turning plate needs the full stop and make-safe steps before any hand goes near it. Models with an impeller are compared in my roundup of the best broadcast spreaders.

My tip: read the drive and parts pages of your manual before the first fill, because the direction of spin and the part names are listed there. The spinning plate under the hopper is the part that sends the product off a spreader, and it deserves that care.

Frequently Asked Questions

What is an impeller?

An impeller is a spinning part with fins or blades that moves material outward as it turns. On a broadcast spreader it is the plate under the hopper’s gate that flings granules into a fan.

What is the difference between an agitator and an impeller?

The difference between an agitator and an impeller is where each sits and what it does: the agitator turns inside the hopper, and the impeller sits below the gate and throws the product. The Scotts guide labels the agitator inside the hopper and the Rotary Disk separately.

What does an impeller do on a spreader?

An impeller on a spreader throws the product that drops from the gate. It spins under the hopper, and its fins or vanes fling the granules outward in a fan, as EarthWay’s patent filing describes.

Where is the impeller on a broadcast spreader?

The impeller on a broadcast spreader sits directly below the hopper’s gate, which EarthWay’s patent calls the shut-off plate. Product falls from the open gate onto it, and the Scotts guide labels the same part a Rotary Disk.

Is it safe to touch the impeller on a running spreader?

Touching the impeller on a running spreader is not safe, so keep your hands, feet, hair and loose clothing away while anything can turn. Before you do this, complete the stop and make-safe steps for your spreader in the safe-state box above.

References

  1. Yildirim Y. Effect of side to side spreader angle on pattern uniformity in single- and twin-disc rotary fertilizer spreaders. Appl Eng Agric. 2008;24(2):173-179.
  2. Crozier CR, Roberson GT. Granular fertilizer spreader swath uniformity achieved at varying target application rates. Crop Manag. 2014;13(1):1-6.
  3. Parish RL. The effect of relative humidity on rotary turf spreader patterns. Appl Eng Agric. 1991;7(5):541-544.
  4. Parish RL. The effect of speed on performance of a rotary spreader for turf. Appl Eng Agric. 1987;3(1):17-19.
  5. Wolf DD, Smith ES. Uniformity of seed and fertilizer distribution with a hand-operated spinning spreader. Trans ASAE. 1979;22(4):761-762.

Safety Note: Read the product label and your spreader’s manual before handling product. Follow both; if their instructions cannot both be met, do not use that combination. Registered pesticide use must comply with its labeling. A listed spreader setting is a starting point; calibrate as the manual directs and never exceed the label rate. Wear all protective equipment required by the label and manual before opening the container and during filling, cleanup and jam clearing. Wash your hands before eating, drinking, smoking or using the restroom when working with pesticides. After application, change your clothes and wash your hands immediately, and follow the label’s additional washing and clothing instructions. Keep children, pets and other people away during handling and application and off treated areas for as long as the label requires. Emergency first: if a battery becomes unusually hot, swells, hisses, smells unusual or smokes, stop using the spreader without handling or removing the battery. Keep people away and follow the battery manual’s emergency instructions. If it smokes, burns or presents immediate danger, move away and call 911 or the fire department. Otherwise, complete the applicable stop and make-safe sequence before filling, unloading, reaching into the hopper, clearing a jam, cleaning, lubricating, adjusting, changing parts or batteries, hitching, unhitching, transporting, storing or leaving the spreader. Walk-behind or hand-crank: close the gate, stop walking or cranking, and wait for all moving parts to stop. Tow-behind: close the gate, stop the vehicle, set the parking brake, switch off the engine and remove the key as the vehicle manual directs, and wait for the wheels, impeller and agitator to stop before reaching into the hopper or touching the impeller. Battery spreader: release the trigger or close the gate, switch off, wait for moving parts to stop, then remove the battery as the manual directs and keep it away while working. Follow any additional isolation steps in the exact manual. Keep hands, feet, hair and loose clothing away from moving parts. Clear jams only by the manual’s method. Refit guards and covers and check the gate before refilling. With the spreader made safe and the gate closed, fill fertilizer on a hard surface where spills can be collected, away from drains and water. Follow the label’s handling and ventilation directions and the manual’s fill limit. Keep people and pets away from spills. Follow the label and safety data sheet for collection, reuse and disposal; do not spread concentrated spills onto the lawn or return contaminated product to its bag. Sweep scattered plain fertilizer from pavement onto the intended lawn before watering only without exceeding the label rate. Follow the label’s cleanup instructions for pesticide granules. Never wash product into streets, gutters, drains, ditches or water. Observe applicable buffers. EPA advises against fertilizing before windy or rainy days; Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Close the gate before stopping or turning, as the manual directs. Follow both towing manuals for hitching, turning, slopes, speed and load limits; never ride on the spreader or carry passengers on it. Use only batteries specified for the model. Recharge rechargeable batteries only with a charger approved for them, as the manual directs; never recharge disposable cells. After completing the applicable shutdown, handle leftover product, cleaning water and residues according to the product label. Clean only by methods permitted by both label and manual, keeping contaminated water out of drains and water supplies. Rinse only if permitted, then dry and lubricate as directed. A rinse does not establish that all pesticide residue is gone. Use salt or ice melt only when the product directions and spreader manual permit it. Salt-based deicers can damage metal; follow the model’s cleaning instructions. Do not use lawn fertilizer to melt ice. Store the spreader empty, clean and dry as its manual directs. Keep products securely closed in their original labeled containers under their labels’ storage conditions, away from children and pets. Lock pesticides away, separate from fertilizer, food and feed; never use food or drink containers. For human exposure, follow the label’s first-aid instructions, call Poison Control at 1-800-222-1222 and keep the label available. Call 911 for immediate danger.

Scroll to Top