Here is how to pressure wash a deck: read the manual, make the machine and the area safe, connect the water before the power, and follow the label of whatever you apply. The USDA Forest Service says power washing can remove wood from the surface, so the washer’s manual and the finish maker’s label come first. I read the label before I open any bottle on my own land, and I read a washer’s manual the same way. Below you get the steps, what the sources say about wood and older decks, and the safety checks for a corded washer.
How to Pressure Wash a Deck: The Order of Steps
This guide covers corded electric washers, the type described in the three manuals quoted here: the Greenworks GPW3002A and GPW2003 and the Westinghouse ePX3500. A gas or battery washer follows its own manual, which adds engine or battery steps this page does not give. Your own manual’s steps replace any line here that differs, and the manual and the label of whatever you apply give the pressure, nozzle and product. If you are weighing battery against corded, my page on corded and battery pressure washers sets out what each type’s manuals print.
Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. That pointer comes before every hands-on step below.
- Read the manual for your exact washer, and the care instructions for your deck’s wood and finish, before you connect anything.
- Find out how old the deck is and plan where the wash water will go, because both can change whether you wash at all.
- Complete the safe-state steps in the box below, then put on safety glasses or goggles and closed footwear.
- Connect the garden hose and turn the water on before the power, then purge the air at the trigger in the order your manual gives. Before you connect a hose, complete the safe-state steps first.
- Start the washer and keep the trigger lock on whenever you stop spraying, holding the gun with two hands as your manual says.
- Spray with the nozzle and any cleaner your manual names for the job, and keep the stream away from people, pets and your feet.
- Stop, release the trapped pressure and make the washer safe in your manual’s order before you disconnect a hose or put anything away.
- Follow the finish maker’s label for preparation and drying time before any stain or sealer goes on.
The Safe-State Box
Every hands-on step in this guide starts after the box below. It is the order for a corded electric washer, and later sections point back to it. For the general order that manuals give across makers, see my guide to using a pressure washer.
Safe-State Box for a Corded Electric Washer
Stop and make safe before you connect or disconnect a hose, change a nozzle, wand or accessory, clear a clogged nozzle, clean a filter, add detergent, refuel, check the oil, charge or change a battery, drain the washer, move it, store it or leave it. Release the trigger and engage the trigger lock on the spray gun. Corded electric washer: turn the washer off with its power switch and wait until all moving parts have stopped. Every washer, after the steps above for your type: follow your manual’s water-supply shutdown and pressure-relief procedure. Point the gun away from people, pets and electrical equipment at a discharge location your manual and the detergent label permit. Disengage the trigger lock, squeeze the trigger to relieve the trapped pressure as the manual directs, then engage the lock again. Then unplug a corded washer by the plug, not by the cord, with dry hands,. Do not disconnect hoses or change nozzles before the pressure is relieved. If the manual’s procedure does not release the pressure, stop and get service; do not loosen a fitting to release it. Only then disconnect hoses or change nozzles. Where your manual gives a different order for these steps, follow your manual’s order. Follow every applicable step in your manual, in the order it specifies, and check that every hose, fitting and nozzle is attached and undamaged before water or power goes back on.
The Short Version
Water goes on before power, and protection goes on before water. Your manual’s order outranks every general list, this one included.
I recommend keeping the manual’s start page open beside the machine for the first run and ticking its steps off in order, with my guide to starting an electric pressure washer as additional reading.
What Power Washing Can Do to Deck Wood
A deck is a surface of wood fibers sitting right where the stream lands. The USDA Forest Service’s Forest Products Laboratory says that aggressive scrubbing with a caustic cleaner or power washing can remove wood from the surface, particularly on softer wood such as western redcedar (1). Treat every setting as the manual’s to give. My answer to “what should you never pressure wash” lists what the manuals warn against.
Weathered Silver Wood Is Not Dirt
The same laboratory notes that when a deck has lost its natural color, the wood may look colored when wet but silver when dry after cleaning. The silver comes from empty wood fibers that should not be removed, because they absorb stain well (1). A gray deck is not automatically a deck to strip back, so I recommend comparing what you see with what the finish label asks for.
Deck Cleaners and Your Washer’s Pump
The Forest Products Laboratory names commercial deck cleaners, brighteners and restorers as products for weathered decks, and says they do not add color (1). That is a statement about the wood and the product. What may pass through a washer’s pump is a separate question, and only the washer’s manual answers it.
Greenworks says in its GPW3002A manual not to use household detergents, acids, alkalines, bleaches or solvents, which can damage the pump. Its GPW2003 manual says not to use bleach, chlorine or any cleaners containing acids, and Westinghouse says to use only detergent formulated for pressure washers. Where your manual forbids a product in the pump, that washer does not apply it, and you read the label of whatever you choose before you open it. My Greenworks GPW3002A pressure washer review covers that model in full.
Check the Age of the Deck First
Decks built before 2004 were often made of CCA-treated wood, which contains arsenic and chromium, according to the University of Florida. In its study, wet CCA-treated wood released more surface arsenic than dry wood, and cleaning with bleach left chromium on the surface and in the rinse water (2). The wood came from one 25-year-old deck cleaned with tap water, bleach and pressure washing, so the study does not say that pressure washing alone causes the release.
The university’s news release adds that rinse water held arsenic and chromate above regulatory limits. Its advice for a CCA-treated deck is to keep children and pets off the wet lumber and not to grow vegetables in the soil nearby. I recommend you find out when the deck was built before the washer leaves the shed.
Painted Decks and Older Paint
Check both your washer’s manual and the care instructions of the surface or finish maker before you wash, and follow their restrictions. If they prohibit pressure washing, do not use a different nozzle or setting as a workaround. My list of surfaces you can pressure wash goes through what the manuals allow, surface by surface.
Older paint can contain lead. EPA’s lead-based paint program says pressure washing is not a prohibited practice under its renovation rule, but it is subject to the same containment requirements as other work, and the wastewater must be disposed of properly, so check with your local water treatment authority. That rule covers contractors working in homes built before 1978, and I send you to EPA’s lead pages before you wash old paint on your own house.
Set Up Safely Before Water or Power Goes On
A pressure washer turns a garden hose into a stream that can cut skin, and the gun pushes back when you squeeze the trigger. Read the pressure washer’s manual before you connect water or power, and follow it. Its warnings, its operator rules and its steps for your exact model come before anything in this article.
Protective Equipment, the Spray and Footing
Wear safety glasses or goggles and closed footwear when you operate the washer, and put them on before you start; where your manual requires goggles, side shields or a face shield, that requirement replaces the minimum here. Follow the manual’s additional protective-equipment requirements, including hearing protection where the manual requires it, and the detergent label’s requirements when you handle detergent. Keep your hands and feet away from the spray. Protective equipment does not make contact with the stream safe.
Greenworks asks in its GPW2003 manual for eye protection with side shields marked ANSI Z87.1, and Westinghouse says never to run the ePX3500 in bare feet, sandals or open-toed shoes. Mississippi State Extension’s safety newsletter adds gloves, because the hand is the most common point of injection injuries.
Never point the spray at yourself, another person, a pet or any part of the body. Keep your hands and feet away from the nozzle and the stream. Get medical care without delay for a spray wound, even if it looks minor at first.
Tell the clinician that a pressure washer caused the injury. CDC describes spray wounds that might first appear minor (3). Case reports describe infection, compartment syndrome and in some cases amputation after a washer injected fluid under the skin (4), and a case series of three eye injuries ended with poor final vision (5).
Engage the trigger lock on the spray gun whenever you stop spraying, even for a moment, before you set the gun down, and before you walk away or change position. Disengage the lock only for controlled spraying or for the manual’s pressure-relief procedure, with the gun pointed in a safe direction.
Two Hands, Footing and Kickback
Westinghouse says to hold the spray gun and lance with two hands until you get used to the recoil, and to point the gun in a safe direction when you squeeze the trigger. The GPW2003 manual says to keep both hands on the trigger handle at all times, and the GPW3002A manual says to hold the spray gun securely with both hands when the product is on.
Hold and brace the spray gun as your manual instructs, keep firm footing on a surface that is not slippery, and follow your manual’s warning about the push of the gun when you squeeze the trigger. Start the stream away from your feet and from anyone else, and never swing the gun toward people or pets as you turn. Westinghouse adds that surfaces become slippery when wet and extra slippery with a detergent or cleaner. Mississippi State Extension also says to take precautions against slippery walking areas, and a wet deck is exactly that.
Keep children, pets and other people away from the work area while the machine runs, and never let a child use the machine. Store the washer and its battery or fuel where children cannot reach them.
Raised Decks, Ladders and Height
Do not use a pressure washer for a task at height, such as from a ladder, unless your manual expressly permits the equipment and the method. Mississippi State Extension’s safety newsletter warns that the kickback force can push you off a ladder. A deck that needs a ladder to reach is a deck for a different method, not for a longer reach.
Corded Electric Washers
All three manuals describe a corded washer with a GFCI plug, so the electrical rules come first. Read the sentences below, and read your manual’s version of them too.
Use the electrical supply and the GFCI protection your manual specifies, and test the GFCI before use according to its instructions. If the washer trips a GFCI or a circuit breaker while you use it, stop using it and have a qualified repair person examine it before you use it again; do not keep resetting it and carry on. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong.
Never cut or splice a power cord or an extension cord. Wear closed, rubber-soled footwear that gives some electrical insulation, plus any additional footwear the manual requires; footwear does not replace GFCI protection or the other electrical precautions. Use an extension cord only if your manual permits it, and then only the type and length it names.
Keep every plug and cord connection dry, out of standing water and away from runoff and the area you are washing, and keep the spray away from outlets, wiring and electrical equipment. Do not use a damaged cord or plug.
The Westinghouse, GPW3002A and GPW2003 manuals each say to keep connections dry and raised off the ground, and Westinghouse says to plug the ePX3500 into a grounded 120 volt outlet even though the washer is double insulated.
Connect the Hose, Purge and Start
Before you inspect parts or connect hoses, complete the applicable stop and make-safe steps in the safe-state box. Inspect the high-pressure hose, the spray gun and every fitting before each use, as your manual describes, and do not use a damaged part. Replace a damaged high-pressure hose; never repair or patch it. Connect the hoses and turn on the water before you start the machine, and purge and start it in the order your manual specifies.
Westinghouse says to turn the water supply on before the power and warns that running the pump dry of water damages the internal components. Greenworks tells you on the GPW3002A to let water flow through the garden hose for 30 seconds before you connect it and to pull the gun trigger to release air before you switch on. The GPW2003 manual has you run water with the motor off until a steady stream appears, and says to turn the washer off and bleed more air out if the stream pulses. I recommend flushing the hose and checking the inlet screen in daylight, before the first connection of the day.
Read the Manual Before You Pick a Nozzle or a Cleaner
The table shows which manual or label governs each decision on a deck job.
| Decision | Who sets it |
|---|---|
| The washer’s pressure and flow | The maker’s printed rating for your exact model |
| The nozzle for the job | Your manual, which names its own nozzles |
| A cleaner through the pump | Your manual’s list of what the pump allows, then the product label |
| Preparing the wood for a finish | The finish maker’s label |
| How much the wood can take | Your manual and the finish maker; the Forest Service warns that power washing can remove wood |
| Where the wash water goes | Your city or county stormwater office |
Nozzles
Use only the nozzles and accessories your manual permits, following its instructions for the job. Never direct any nozzle at skin, people or animals. Before you change a nozzle, complete the stop and make-safe steps in the safe-state box.
Greenworks and Westinghouse each print a nozzle list in the manual, and my explainer on nozzle colors on pressure washers shows how makers label them, though the list in the manual of your own washer is the one to read. I recommend reading that list before the first start, not at the first clogged nozzle.
Detergent and Cleaners
Before you add detergent or connect or adjust a detergent accessory, complete the applicable stop and make-safe steps in the safe-state box. Use only the detergents your manual allows, through the detergent system the manual describes, and read the detergent label before you open it. Wear the protective equipment the detergent label requires, and avoid contact of detergent with your eyes and skin. Do not run a detergent that your manual does not name through the pump.
I read the whole label before I open a container, first-aid section included. Greenworks says its GPW3002A applies detergent only with the black soap nozzle installed, and its GPW2003 manual says soap cannot be applied under high pressure on that machine. If someone is hit by the stream, get medical care without delay, even if the wound looks small.
If someone swallows a cleaning product or gets it in the eyes, follow the label’s first-aid section and call Poison Control at 1-800-222-1222. Call 911 for a fire or immediate danger.
Keep Wash Water Out of Storm Drains
I check which way the ground slopes before I unroll a hose, because the drain path decides everything else. Before you wash, plan how to keep wash water, detergent and debris out of streets, storm drains, ditches and streams, because a storm drain carries what enters it to local waters without treatment. Check with your city or county stormwater office about collecting and disposing of the wash water for the job.
Send wash water to landscaping only where local rules and the detergent label permit it and the soil can absorb it without runoff or contamination. Otherwise contain and collect it for an approved disposal route. Do not assume that water carrying oil, paint debris, pesticide residue or material from an old treated deck is suitable for a lawn.
EPA says a storm drain leads to local waterbodies, not to a treatment facility (6). Its sheet is written for vehicle washing and local rules differ, which is why the call to your stormwater office matters. On a CCA-treated deck the rinse water carries more than dirt, as the University of Florida study found.
Before You Stain or Seal the Deck
Preparation and drying time before a finish belong to the finish maker’s label, and the label of any cleaner you used adds its own instructions. The Forest Products Laboratory adds what it says about the finishes themselves.
The laboratory recommends penetrating finishes for decks, such as water-repellent preservatives and semitransparent stains, over film-forming finishes. A deck with a factory-applied water-repellent finish, or one recently treated with a water-repellent preservative, may need 2 to 3 months of weathering before a semitransparent stain absorbs properly (1). I keep wet CCA-treated wood off limits to children and pets, as the University of Florida advises.
Stop and Make Safe When You Finish
Pressure stays trapped in the hose and gun after the machine is off, so stopping is part of the job. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above.
Each manual gives its own stop order, and the orders differ, so I list them one by one. Westinghouse has you press the start/stop button and then point the gun in a safe direction and pull the trigger to release the pressure, and it says never to disconnect the high-pressure hose while the system is pressurized. The GPW3002A manual runs from the trigger and the power switch through the water supply, the pressure release and the lock-out to disconnecting the cord. The GPW2003 manual says to release the trigger and press the switch to off, and notes that the system may hold pressure even when you cannot hear the pump.
Never leave the washer running, connected to mains power or pressurised. Before you store the pressure washer, complete the stop and make-safe steps in the safe-state box. Drain and store it as your manual directs, in a place the manual allows and away from children. Store a battery as the battery manual describes, and fuel as the manual and the fuel container’s label describe.
What to Remember Before You Wash
Three things carry over to any deck job. Check the deck’s age before the washer comes out, follow your manual and the finish label for every setting, and complete the safe-state steps before each hands-on step. My own habit is small: I put the manual’s start page and the finish label side by side before any job that involves water and wood. Next, read the stormwater page of your own city, then reopen the box above. Follow that order and you know how to pressure wash a deck without guessing at settings the manuals already give. If you are still choosing a machine, my list of pressure washers for decks shows the corded electric models I recommend.
Frequently Asked Questions
Should you pressure wash a wooden deck?
You should pressure wash a wooden deck only after reading your washer’s manual and the deck’s finish instructions, because the Forest Products Laboratory says power washing can remove wood from the surface, particularly on softer wood such as western redcedar. The same laboratory names commercial deck cleaners and brighteners as products for weathered decks.
Should you pressure wash a deck before staining?
Washing a deck before staining is a choice that the stain label and your washer’s manual govern, and the label sets the preparation and the drying time. The Forest Products Laboratory recommends penetrating finishes for decks and says a deck with a factory-applied water-repellent finish may need 2 to 3 months of weathering before a semitransparent stain absorbs properly.
Can you pressure wash a painted deck?
Pressure washing a painted deck depends on two sets of instructions, your washer’s manual and the care instructions of the paint or finish maker, and if either prohibits pressure washing, no other nozzle or setting is a workaround. Older paint can contain lead, and EPA’s lead program says pressure washing is subject to the same containment requirements as other work under its renovation rule, so read EPA’s lead pages before washing old paint.
What protective gear do you need to pressure wash a deck?
Safety glasses or goggles and closed footwear are the minimum when you pressure wash a deck, put on before you start. Your washer’s manual can require more, such as side shields on the eye protection, and the label of any cleaner adds its own requirements.
Is it safe to stand on a wet deck while you pressure wash it?
Standing on a wet deck while you pressure wash it carries a slip risk, because Westinghouse says surfaces become slippery when wet and extra slippery with a detergent or cleaner. Keep firm footing, wear closed footwear, hold the gun as your manual instructs, and keep children and pets off wet CCA-treated wood.
References
- Knaebe M. Finishes for wood decks. FinishLine. USDA Forest Service, Forest Products Laboratory. Revised July 2013.
- Gress J, de Oliveira LM, da Silva EB, et al. Cleaning-induced arsenic mobilization and chromium oxidation from CCA-wood deck: potential risk to children. Environ Int. 2015;82:35-40. doi:10.1016/j.envint.2015.04.012
- Centers for Disease Control and Prevention. Pressure washer safety. Natural Disasters. Published May 15, 2024. Reviewed August 26, 2026. Accessed October 31, 2026.
- Funato N, Sugizaki Y, Ri Y, Ichibayashi R. High-pressure injection damage caused by a high-pressure washer. Cureus. 2024;16(1):e52498. doi:10.7759/cureus.52498
- Placide J, Yang MY, Gross AW, Crowell EL. Case series: traumatic ocular lacerations secondary to pressure washers. Am J Ophthalmol Case Rep. 2022;27:101612. doi:10.1016/j.ajoc.2022.101612
- US Environmental Protection Agency. Stormwater best management practice: vehicle maintenance and washing. EPA-832-F-21-032F. February 2023.
Safety Note: Read your pressure washer’s manual before you connect water or power, and follow it. Never point the spray at yourself, another person, a pet or any part of the body. Keep hands and feet away from the nozzle and stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. Wear safety glasses or goggles and closed footwear before operating the washer, plus any additional protection required by the manual and the detergent label. Follow the manual’s instructions for the trigger lock, grip, footing and recoil, and engage the trigger lock whenever you stop spraying. Use only the nozzles, accessories and detergents the manual permits, and never point any nozzle at skin, people or animals. Do not perform a task at height without instructions expressly permitting the equipment and method in the exact manual. Gas models: operate outdoors, never inside a building or a partly enclosed space. Keep the engine at least 20 feet from any window, door or vent, following CDC’s pressure washer guidance and any stricter manual requirement. Exhaust contains carbon monoxide, which cannot be seen or smelled and can kill. Opening doors or windows does not make indoor operation safe. Refuel only with the engine off and cool, following the manual. Corded models: use the manual’s specified electrical supply and GFCI protection, and test the GFCI before use according to its instructions. After an operating GFCI or breaker trip, do not reuse the washer until a qualified repair person has examined it. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Wear closed, rubber-soled footwear that provides some electrical insulation, plus any additional footwear required by the manual; footwear does not replace GFCI protection or the other electrical precautions. Never cut or splice cords. Use an extension cord only as the manual permits. Keep connections dry and away from runoff, standing water and the washing area, and keep spray away from electrical equipment. Battery models: use only the battery and charger the maker specifies for your exact model. Emergency first: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Otherwise, complete the applicable stop and make-safe procedure before hose, nozzle, wand or accessory work, clearing a blockage, cleaning, maintenance, refueling, checking oil, adding detergent, battery changes or charging, draining, moving, transporting, storing or leaving the washer. Follow your exact manual’s procedure and order. Release the trigger and engage its lock. Gas: switch the engine off and wait for it to stop; disconnect the spark plug wire before service as the manual directs, and let hot parts cool before refueling, storage or contact. Corded: switch off and unplug by the plug with dry hands. Battery: switch off, remove a removable battery as the manual directs and keep it away while working; for a built-in battery, follow the manual’s isolation procedure and do not open the battery compartment. Complete the manual’s water-supply shutdown and pressure-relief steps: point the gun in a safe direction at a permitted discharge location, disengage the trigger lock, squeeze the trigger as directed to relieve pressure, then reengage the lock. Do not disconnect hoses or change nozzles until pressure is relieved. If pressure cannot be relieved by the prescribed procedure, obtain service without loosening fittings. Refit and inspect parts before restoring water or power. Replace a damaged high-pressure hose; never repair or patch it. Before you wash, plan how to keep wash water, detergent and debris out of streets, storm drains, ditches and streams, and check with your city or county stormwater office about collection and disposal. Send wash water to landscaping only where local rules and the detergent label permit it and the soil can absorb it without runoff or contamination. Keep children and pets away, and never let a child use the machine. Drain and store the washer as its manual directs. For exposure to a cleaning product, follow the label’s first-aid instructions and call Poison Control at 1-800-222-1222. Call 911 for a fire or immediate danger.

