A woman holding an electric pressure washer spray gun with a puzzled expression on a patio

Why Is My Pressure Washer Pulsing? What the Manuals Say to Check

A pressure washer pulses when its pump gets an uneven supply of water or an uneven path out, and the maker manuals name four outside causes: air in the pump and hoses, a weak water supply, a clogged inlet filter or screen and a blocked nozzle. Each one has a check you can make without opening the pump, and each check starts with a machine that is stopped and safe.

The drip irrigation I built runs through a 150-mesh disc filter at the pump head, so when any pump misbehaves I look at what feeds it before I blame the pump. Below you get the causes model by model, the checks in the manuals’ own order and the point where the job goes to the maker.

Why Is My Pressure Washer Pulsing? The Short Answer

The makers do not agree on the word. Simpson’s table says “Pump or nozzle pulsates,” CRAFTSMAN says the pump pressure will pulsate when a nozzle is partly clogged, Greenworks and Kärcher say the output pressure varies high and low, and WORX says the pressure is not consistent. They do agree on the causes, so the table below lists them side by side.

What each manual lists when the pressure rises and falls
Model The manual’s wording Causes it lists
Simpson PowerShot PS3228 (gas) Pump or nozzle pulsates Nozzle obstructed. Its low or no pressure row adds trapped air, a weak water source, a clogged nozzle and a clogged inlet screen
Greenworks GPW2003 (corded) Output pressure varies high and low Not enough inlet water, pump sucking air, clogged inlet filter, supply voltage below minimum
Greenworks GPW3002A (corded) The output pressure varies high and low Water supply not sufficient, pump drawing in air, clogged water intake filter, low supply voltage
CRAFTSMAN CMEPW2100 (corded) Output pressure varies high/low Not enough inlet water, pump sucking air, clogged inlet screen, obstructed nozzle
Kärcher K1700 Cube (corded) Output pressure varies high and low Not enough inlet water, pump sucking in air, clogged inlet filter, obstructed nozzle
WORX WG602 (corded) Machine pressure is not consistent Faulty pump (contact the service center), air in line, clogged or dirty water inlet adapter

Simpson prints one cause under its pulsing row, a blocked nozzle, and the same outside causes sit under its low or no pressure row. WORX lists a faulty pump under its inconsistent pressure row and tells you to contact the service center.

Stop at the First Pulse

Stop spraying as soon as the stream pulses, and finish the safe-state steps below before you touch a hose, a filter or a nozzle. Keep spraying to see whether it clears is never one of the manuals’ checks.

Make the Washer Safe Before You Check Anything

Every check on this page puts a hand near a hose, a filter, a nozzle or the gun, so each one starts from the box below. Once the pressure washer is pulsing, finish the box before you do anything else.

Stop and Make Safe

Emergency first, for a washer with a battery: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Stop and make safe before you connect or disconnect a hose, change a nozzle, wand or accessory, clear a clogged nozzle, clean a filter, add detergent, refuel, check the oil, charge or change a battery, drain the washer, move it, store it or leave it. Release the trigger and engage the trigger lock on the spray gun. Gas washer: turn the engine off with its switch as the manual says and wait until all moving parts have stopped. Let the engine and the muffler cool for the time your manual gives before you refuel, store the washer or touch hot parts, and disconnect the spark plug wire before maintenance where your manual directs it. Corded electric washer: turn the washer off with its power switch and wait until all moving parts have stopped. Battery washer: turn the washer off and wait until all moving parts have stopped. Every washer, after the steps above for your type: follow your manual’s water-supply shutdown and pressure-relief procedure. Point the gun away from people, pets and electrical equipment at a discharge location your manual and the detergent label permit. Disengage the trigger lock, squeeze the trigger to relieve the trapped pressure as the manual directs, then engage the lock again. Then unplug a corded washer by the plug, not by the cord, with dry hands, or remove the battery from a battery washer as your manual directs and keep it away from the washer while you work. Do not disconnect hoses or change nozzles before the pressure is relieved. If the manual’s procedure does not release the pressure, stop and get service; do not loosen a fitting to release it. Only then disconnect hoses or change nozzles. Where your manual gives a different order for these steps, follow your manual’s order. Follow every applicable step in your manual, in the order it specifies, and check that every hose, fitting and nozzle is attached and undamaged before water or power goes back on.

The manuals do differ on the order, and each maker’s order wins for its own machine. I keep these orders apart and never merge them.

  • Simpson PS3228: set the trigger lock, switch the engine off, turn off the water supply, squeeze the trigger to relieve the pressure in the hose and pump, then allow the engine to cool completely before handling and storage.
  • Westinghouse ePX3500: point the gun in a safe direction and pull the trigger to release the pressure. Its storage steps release the pressure and then unplug the washer.
  • EGO HPW3200 (twin of the HPW3204-2): lock the trigger, power off, close the faucet, squeeze the trigger to empty the hoses, disconnect the hoses and accessories, run the power briefly to drain the pump, power off, and only then remove the battery packs.
  • Greenworks: purge the air with the motor off before you connect power.

If the stream settles after you finish the box and make the checks, resume only on the conditions your manual gives. Then test the spray again with the short block below in mind.

The Stream Is the Hazard When You Test Again

Spray at People

Never point the spray at yourself, another person, a pet or any part of the body. Keep your hands and feet away from the nozzle and the stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury.

The reason is the injection injury. A case report on a pressure washer injury describes infection, compartment syndrome and in some cases amputation (1), and a finger injury at close range needed emergency surgery although the X-ray showed no fracture (2). A review of the literature on injection injuries to the upper extremity describes a real amputation risk and says early surgical care matters (3). US emergency department data single out pressure washers as the most common source of hand injection injuries (4).

Protective Equipment

Wear safety glasses or goggles and closed footwear when you operate the washer, and put them on before you start; where your manual requires goggles, side shields or a face shield, that requirement replaces the minimum here. Follow the manual’s additional protective-equipment requirements, including hearing protection where the manual requires it, and the detergent label’s requirements when you handle detergent. Keep your hands and feet away from the spray. Protective equipment does not make contact with the stream safe.

The manuals ask for more than the minimum. WORX and Kärcher say safety glasses do not provide full protection and ask for goggles or a face shield, and Kärcher also asks for ear protection. Greenworks asks for eye protection with side shields marked ANSI Z87.1. Simpson asks for ANSI Z87.1 safety glasses or goggles, ear plugs or muffs, long pants, a long-sleeved shirt and rubber-soled shoes that fully cover the feet.

  • Trigger lock: engage it whenever you stop spraying, even for a moment, before you set the gun down.
  • Two hands and footing: hold and brace the gun as your manual instructs, on firm footing, and follow its warning about the push of the gun.
  • Height: do not use a pressure washer for a task at height, such as from a ladder, unless your manual expressly permits the equipment and the method.
  • Runoff: keep wash water, detergent and debris out of streets and storm drains.

Gas and Battery Washers

Two of the models named on this page need a rule of their own. The Simpson PowerShot PS3228 is a gas washer, and the EGO HPW3204-2 is a battery washer.

Gas Washer Exhaust

Operate a gas pressure washer outdoors, never inside a building or a partly enclosed space. CDC says to keep it at least 20 feet from any window, door or vent, and your manual may set a stricter placement, which you follow. Engine exhaust contains carbon monoxide, which you cannot see or smell and which can kill. Opening a door or a window does not make it safe to run an engine inside. If anyone develops symptoms such as headache, dizziness, weakness, nausea or confusion, move to fresh air and get emergency medical care.

Battery Washer

Use only the battery and the charger the maker specifies for your exact pressure washer, and charge, store and handle them only as your manual describes. Before you change or charge the battery, follow the emergency exception and the applicable stop and make-safe steps in the safe-state box. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger. If you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a battery, stop using it and follow your battery manual’s emergency instructions.

Is It Really Pulsing? Normal Motor Runs on Auto-Start Models

Before you take anything apart, check that the machine is faulty at all. Westinghouse’s ePX3500 manual describes an auto-start feature: push the start button once and the unit runs for several seconds and shuts off, which the manual calls a normal function. It adds that it is normal to hear the motor run intermittently when the trigger is not being squeezed, because the pump is priming itself for the next squeeze. The full start routine for a corded washer is in my guide to starting an electric pressure washer.

That covers pressure washer pulsing when idle on that model. The troubleshooting table has a row for a washer that turns on for 2 seconds, shuts off and will not turn back on: the motor may run for 1 to 2 seconds to prime the pump, then it shuts off until the spray gun trigger is squeezed, and the manual says this is normal and does not indicate a problem.

The same manual says the unit could be pressurized even if you do not hear the motor and pump running, so a quiet machine still gets the box above. It also says that squeezing the trigger rapidly makes the auto-start feature miss an on and off cycle, which is the manual’s reason for slow, deliberate trigger pulls. My guide to a pressure washer shutting off lists the causes and the safe checks.

These lines belong to the ePX3500. Another washer follows its own manual, and I recommend reading the operating notes of your exact model before you call a short motor run a fault.

Air in the Pump and Hoses

Air is the cause the manuals name most often, and the purge is the fix they share. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Greenworks puts it in the starting steps of its GPW2003 manual: turn the water on, squeeze the trigger and run water through the hose with the motor off until a steady stream appears, which helps drain air from the tank and lines.

The GPW2003 manual also says what to do when the stream pulses. If the pressure washer pulsates and the water stream is intermittent, turn it off and continue to bleed air out of the system, and make sure the garden hose is fully turned on and not kinked.

What the Other Manuals Say About Air

Greenworks’ GPW3002A manual lists “the pump is drawing in air” under varying output pressure: make sure the hoses and fittings are airtight, turn the product off, then purge the pump by squeezing the trigger gun until a steady flow of water comes out the spray tip. CRAFTSMAN gives the same remedy for “pump is sucking air” on the CMEPW2100 and lists that cause under a pump that is excessively noisy too. Kärcher’s K1700 Cube table repeats it almost word for word, and Simpson’s PS3228 manual lists air trapped in the pump or hoses under low or no pressure and sends you to its section on purging the pump. I review the GPW3002A itself in my Greenworks pressure washer review.

CRAFTSMAN’s operating steps add a time: hold the trigger for 30 seconds to purge the system of air before you turn the washer on. That is one maker’s step, so check your own manual for its figure. WORX gives a different remedy for air in the line on its WG602 that has you work with the machine on, so follow the WORX manual and not the others for that machine, and finish the box first.

In the Greenworks, CRAFTSMAN and Kärcher remedies the purge happens with the machine switched off and the water on. Point the gun in a safe direction while you squeeze the trigger, as your manual directs, and keep your hand off the nozzle end.

After the box, I check every fitting for tightness before I purge, since the manuals tie air to hoses and fittings that are not airtight.

Water Supply, Hose and Kinks

A pump that cannot get enough water behaves like a pump with air in it, and every table lists the water supply. Greenworks and Kärcher tell you to turn the water on full force and to check the garden hose for kinks, leaks and blockage, and CRAFTSMAN says the same under not enough inlet water supply. My guide to how a pressure washer works shows where the water goes between the faucet and the pump.

Hose size matters in the manuals that mention it. Under its low pressure rows Greenworks asks for a 1 inch or 5/8 inch garden hose and Kärcher asks for 5/8 inch or larger. Simpson prints its own water-supply requirement in the manual, a source that can supply at least 5 GPM at 20 PSI, and says the high-pressure hose should be less than 100 feet long. Those are Simpson’s figures for its washers, not a rule for any other machine.

A farm yard often runs its hose from a well or an irrigation line. Westinghouse’s ePX3500 manual says to connect the washer to a water main and not to a lake, pool or pond, so read what your manual allows as a water source before you blame the machine.

Water Supply and Start-Up

Before you inspect parts or connect hoses, complete the applicable stop and make-safe steps in the safe-state box. Inspect the high-pressure hose, the spray gun and every fitting before each use, as your manual describes, and do not use a damaged part. Replace a damaged high-pressure hose; never repair or patch it. Connect the hoses and turn on the water before you start the machine, and purge and start it in the order your manual specifies.

The Inlet Filter or Screen

The filter or screen sits where the garden hose meets the washer, and every manual in the table above names it, Simpson under its low or no pressure row. Simpson says to check the inlet filter before each use and never to operate the washer without it properly installed, and Westinghouse’s ePX3500 manual says never to connect a garden hose without the screen in place. I cover the neighbouring problem in my guide to a pressure washer losing pressure.

Before You Clean the Filter

Before you clean the machine, check or clean the inlet filter, or do any other maintenance, complete the stop and make-safe steps in the safe-state box. Do the maintenance your manual describes, in the order it describes it, and do not use a part or an accessory the maker does not name.

How the Manuals Clean It

Greenworks says to remove the filter and rinse it in warm water, and Kärcher says to remove the garden hose adapter and rinse it out in warm water. CRAFTSMAN says to rinse the screen off with water, and WORX says to remove the adapter, rinse it with water and put it back. Simpson’s maintenance text has you remove the filter from the garden hose coupler, clean both sides with running garden hose water and insert it with the convex side facing out.

The 150-mesh disc filter at my irrigation pump head is the picture I keep in mind: it holds debris out of the pump, and a washer’s inlet screen does the same job at a smaller size. I recommend looking at the screen before you look at anything deeper in the machine.

A Clogged Nozzle

A blocked nozzle is the one cause Simpson prints under its own pulsing row, and another manual says it in plain words. Simpson’s PS3228 manual says that if a nozzle becomes clogged the pump may pulsate and the spray pattern could change, and that if the nozzle is not cleaned, excessive pressure may develop, possibly damaging the pump or other accessories. CRAFTSMAN says that a partly clogged or restricted nozzle makes the pump pressure pulsate, and to clean it immediately with the nozzle cleaner. Which tip is which differs by maker, and my page on pressure washer tip colors shows how.

Clearing a Clogged Nozzle

A nozzle that gives a weak, uneven or pulsing stream may be blocked. Complete the stop and make-safe steps in the safe-state box, then clear the nozzle only with the tool and the method your manual describes. Never look into the nozzle or point it at anyone to check it.

Simpson’s manual gives the order below for its PS3228, after the box and in the maker’s own sequence. Other makers differ, so your manual’s order wins. I trust a maker’s own step order over any order I could invent.

  1. Shut off the pressure washer.
  2. Turn off the water supply.
  3. Point the spray gun in a safe direction and squeeze the trigger to relieve the water pressure.
  4. Set the trigger lock.
  5. Remove the nozzle from the lance quick connector.
  6. Clear any obstructions from the nozzle with the nozzle cleaning tool provided.
  7. Rinse loose debris from the nozzle by directing a running garden hose into its output for at least 30 seconds.

CRAFTSMAN’s order for the CMEPW2100 is similar: shut off the unit, turn off the water, pull the trigger to relieve the pressure, pull the quick connect collar toward the spray wand to take the nozzle off and clear the debris with the spray tip cleaning tool. The tool differs by maker. Kärcher names a fine needle, WORX a declogging needle, and EGO’s HPW3200 manual, the twin of the HPW3204-2, a nozzle cleaning needle with the battery pack removed before servicing. Westinghouse’s ePX3500 table says only to clean the nozzle, so use the tool your manual names. The washer itself is covered in my review of the CRAFTSMAN CMEPW2100.

I recommend keeping the cleaning tool with the manual, so the maker’s own method is within reach when the stream goes uneven.

What the Manuals Leave to the Maker

Some causes on the lists are not an owner’s job. WORX lists a faulty pump under its inconsistent pressure row and the remedy is to contact the service center, and it adds that any other servicing should be done by an authorized service representative. Simpson sends worn piston packing and worn oil seals to customer service, and CRAFTSMAN sends a worn nozzle, damaged water seals and worn oil seals to its service line.

None of these manuals gives the owner a procedure for the pump’s valves or an unloader as a fix for pulsing, so this page gives none. I leave the pump alone and call the maker.

Supply Voltage on Corded Models

Greenworks adds a cause that only an electric washer has. Its GPW2003 and GPW3002A tables list low supply voltage under varying output pressure, and the remedy is to make sure only the pressure washer is running on that circuit. Both Greenworks tables and the Kärcher table also list a calcified gun, hose or nozzle and give a descaling step with a cleaning agent, which I leave to the manual. My comparison of gas and electric pressure washers sets out the fuel, cord and care each type asks for.

When to Stop and Call for Service

Call the maker when pulsing stays after the checks your manual lists, and stop at once for any sign in this list.

  • A leak at the pump or a fitting: Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Simpson lists loose connections to tighten and worn O-rings to check and replace, and sends worn packing and seals to customer service.
  • A damaged high-pressure hose: replace it, as the box and the manuals say. Never repair it.
  • Sparks, smoke, flames or heavy vibration: Westinghouse’s WPX3600 manual says not to use the washer if the unit sparks, smokes, emits flames or vibrates excessively.
  • A tripped GFCI or breaker on a corded washer: see the box below.
  • Pulsing that stays: if it survives the air, water, filter and nozzle checks of your own manual, stop and contact the maker.

Corded Washer Electricity

Use the electrical supply and the GFCI protection your manual specifies, and test the GFCI before use according to its instructions. If the washer trips a GFCI or a circuit breaker while you use it, stop using it and have a qualified repair person examine it before you use it again; do not keep resetting it and carry on. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Never cut or splice a power cord or an extension cord. Wear closed, rubber-soled footwear that gives some electrical insulation, plus any additional footwear the manual requires; footwear does not replace GFCI protection or the other electrical precautions. Use an extension cord only if your manual permits it, and then only the type and length it names. Keep every plug and cord connection dry, out of standing water and away from runoff and the area you are washing, and keep the spray away from outlets, wiring and electrical equipment. Do not use a damaged cord or plug.

CDC gives the same advice: test the GFCI first, and have an electrician check the unit after it trips a breaker. Greenworks’ GPW3002A table says to let a tripped breaker cool and start the product again. I recommend the stricter rule above, so a trip means stop and have the washer examined.

What to Remember Before the Next Start

Stop at the first pulse and finish the safe-state steps before any check. Work through air, water supply, inlet filter and nozzle in the order your own manual lists them. Leave the pump, the seals and the oil to the maker.

Treat any pressure washer pulsing problem as a stop-and-check job. My own tip is to read the troubleshooting table of the manual for your exact model once, on a calm day, so the right row is the first thing you look for. A pulsing pressure washer is a reason to stop, make it safe and use the checks the maker printed for that machine. My walkthrough of using a pressure washer follows the order the manuals give.

Frequently Asked Questions

Why does my pressure washer keep pulsing?

Your pressure washer keeps pulsing because its pump is getting uneven water or an uneven path out, and the manuals name air in the pump, a weak water supply, a clogged inlet filter and a blocked nozzle. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Then check each one in the order your manual lists.

Why is my pressure washer pulsing when idle?

A pressure washer pulsing when idle may be doing what its manual calls normal. Westinghouse’s ePX3500 auto-start motor runs for 1 to 2 seconds to prime the pump and then runs intermittently until the trigger is squeezed. Another model follows its own manual, and any machine can hold pressure when it is quiet.

Why is my pressure washer pulsing when spraying?

A washer that pulses while you spray may have an air, supply or nozzle problem, and Greenworks, CRAFTSMAN and Kärcher list all three under varying output pressure. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Then check the purge, the water and the nozzle in your manual’s order.

Why does my pressure washer surge when I pull the trigger?

A pressure washer that surges when you pull the trigger is reacting to the same four causes, and CRAFTSMAN’s manual says a partly clogged or restricted nozzle makes the pump pressure pulsate. On an auto-start model such as the Westinghouse ePX3500, rapid trigger pulls make the feature miss an on and off cycle, so the manual asks for slow, deliberate pulls. If neither explains it, stop and contact the maker.

Why is my electric pressure washer pulsing?

An electric pressure washer pulses for the same outside causes as any other, and Greenworks adds a low supply voltage and tells you to make sure only the washer runs on that circuit. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. A tripped GFCI or breaker means stop and have the washer examined, and the checks come after.

References

  1. Funato N, Sugizaki Y, Ri Y, Ichibayashi R. High-pressure injection damage caused by a high-pressure washer. Cureus. 2024;16(1):e52498. doi:10.7759/cureus.52498
  2. Choi JH, Choi SY, Hwang JH, Kim KS, Lee SY. Finger compartment syndrome due to a high-pressure washer injury: a case report. World J Clin Cases. 2023;11(13):3017-3021. doi:10.12998/wjcc.v11.i13.3017
  3. Hogan CJ, Ruland RT. High-pressure injection injuries to the upper extremity: a review of the literature. J Orthop Trauma. 2006;20(7):503-511. doi:10.1097/00005131-200608000-00010
  4. Johnson C, Newton W, LaRochelle L, Allen J, Daly C. High-pressure injection injuries of the hand in community and industrial settings: incidence and trends. Hand (N Y). 2025;20(6):917-922. doi:10.1177/15589447231218404

Safety Note: Read your pressure washer’s manual before you connect water or power, and follow it. Never point the spray at yourself, another person, a pet or any part of the body. Keep hands and feet away from the nozzle and stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. Wear safety glasses or goggles and closed footwear before operating the washer, plus any additional protection required by the manual and the detergent label. Follow the manual’s instructions for the trigger lock, grip, footing and recoil, and engage the trigger lock whenever you stop spraying. Use only the nozzles, accessories and detergents the manual permits, and never point any nozzle at skin, people or animals. Do not perform a task at height without instructions expressly permitting the equipment and method in the exact manual. Gas models: operate outdoors, never inside a building or a partly enclosed space. Keep the engine at least 20 feet from any window, door or vent, following CDC’s pressure washer guidance and any stricter manual requirement. Exhaust contains carbon monoxide, which cannot be seen or smelled and can kill. Opening doors or windows does not make indoor operation safe. Refuel only with the engine off and cool, following the manual. Corded models: use the manual’s specified electrical supply and GFCI protection, and test the GFCI before use according to its instructions. After an operating GFCI or breaker trip, do not reuse the washer until a qualified repair person has examined it. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Wear closed, rubber-soled footwear that provides some electrical insulation, plus any additional footwear required by the manual; footwear does not replace GFCI protection or the other electrical precautions. Never cut or splice cords. Use an extension cord only as the manual permits. Keep connections dry and away from runoff, standing water and the washing area, and keep spray away from electrical equipment. Battery models: use only the battery and charger the maker specifies for your exact model. Emergency first: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Otherwise, complete the applicable stop and make-safe procedure before hose, nozzle, wand or accessory work, clearing a blockage, cleaning, maintenance, refueling, checking oil, adding detergent, battery changes or charging, draining, moving, transporting, storing or leaving the washer. Follow your exact manual’s procedure and order. Release the trigger and engage its lock. Gas: switch the engine off and wait for it to stop; disconnect the spark plug wire before service as the manual directs, and let hot parts cool before refueling, storage or contact. Corded: switch off and unplug by the plug with dry hands. Battery: switch off, remove a removable battery as the manual directs and keep it away while working; for a built-in battery, follow the manual’s isolation procedure and do not open the battery compartment. Complete the manual’s water-supply shutdown and pressure-relief steps: point the gun in a safe direction at a permitted discharge location, disengage the trigger lock, squeeze the trigger as directed to relieve pressure, then reengage the lock. Do not disconnect hoses or change nozzles until pressure is relieved. If pressure cannot be relieved by the prescribed procedure, obtain service without loosening fittings. Refit and inspect parts before restoring water or power. Replace a damaged high-pressure hose; never repair or patch it. Before you wash, plan how to keep wash water, detergent and debris out of streets, storm drains, ditches and streams, and check with your city or county stormwater office about collection and disposal. Send wash water to landscaping only where local rules and the detergent label permit it and the soil can absorb it without runoff or contamination. Keep children and pets away, and never let a child use the machine. Drain and store the washer as its manual directs. For exposure to a cleaning product, follow the label’s first-aid instructions and call Poison Control at 1-800-222-1222. Call 911 for a fire or immediate danger.

Scroll to Top