A woman walking along a crop row, a flat fan nozzle emitting a wide horizontal spray pattern

What Is a Fan Spray Nozzle? Pattern, Angle and Droplet Size Explained

A fan spray nozzle sprays liquid as a flat, wide sheet. On the standard flat fan that sheet is lighter at its two edges than in its middle, while an even flat fan spreads the liquid uniformly across its width. North Dakota State University (NDSU) lists the flat fan as one of only three basic spray patterns, next to the hollow cone and the full cone. I trained in plant protection, and the tip is the first part I read on any sprayer, because it shapes every drop that leaves the wand.

Below you will see how the pattern forms, what spray angle and pressure do to it, which types exist and how fan tips fit hand-pump and battery sprayers.

What Is a Fan Spray Nozzle? The Flat, Tapered Spray Sheet

A fan spray nozzle shapes liquid into a wide, flat sheet instead of a cone. According to NDSU, standard flat-fan nozzles produce a tapered-edge pattern, so less liquid lands along the edges of the sheet than in the middle (1). That one feature explains most of what you need to know about them: how wide they spray, why passes must overlap and why the angle matters. NDSU’s even flat fan is the exception, built to spread liquid uniformly across the whole width of its pattern.

The Tapered Edge and Why Passes Overlap

NDSU says the patterns of neighboring flat-fan nozzles must overlap to give uniform coverage along a boom, and that for maximum uniformity the overlap should be about 30% to 50% of the nozzle spacing at the target level (1). Those figures are for a boom with several nozzles on it. A hand wand has one nozzle and no spacing, so the figure does not transfer to a wand.

What does transfer is the idea. A strip sprayed with a standard flat fan is thinner at its edges, so I plan my passes along a plum row as strips with soft edges and let the next strip cross the edge of the last one.

Fan, Cone and Other Basic Patterns

NDSU names three basic patterns: the flat fan, the hollow cone and the full cone (1). It describes the flat fan as widely used for broadcast spraying, meaning covering a whole area rather than a spot. My guide on what a spray nozzle is covers types, droplet size and drift basics.

Key Takeaway

A flat fan nozzle sprays a flat sheet. On a standard tip the edges taper, and on an even tip the liquid spreads uniformly across the width. Its spray angle, its pressure and its overlap with the next pass decide how even the coverage is.

How the Flat Fan Nozzle Spray Pattern Forms

The pattern comes from the nozzle’s shape and the pressure behind it. Two numbers belong to every fan tip: the spray angle of the sheet and the flow the tip passes at a given pressure.

Pattern and Liquid Distribution

Lechler, a German maker of industrial nozzles, says its flat fan nozzles are designed for a parabolic distribution of liquid across the sheet, with special designs for a rectangular or trapezoidal distribution. A parabolic distribution means more liquid in the middle of the sheet and less toward the edges, which matches the tapered edge NDSU describes. Lechler builds nozzles for industrial work such as cleaning, so its page speaks for how a sheet is built and not for a garden wand.

Spray Angle in Plain Words

Every flat-fan tip has a spray angle, and NDSU says most agricultural nozzles have one from 65 to 120 degrees. Narrow angles give a more penetrating spray, while wide-angle nozzles can be mounted closer to the target, spaced farther apart on a boom or used for overlapping coverage (1). In my own words: a narrow fan reaches in, and a wide fan covers more ground from a short distance.

Spray Angle and Nozzle Height on a Boom

Spray angle and height go together on a boom. NDSU prints minimum suggested heights from the nozzle to the target for four angles on two nozzle spacings (1). Read the table as a small flat fan spray nozzle chart that shows one thing: the wider the angle, the lower the nozzle can sit.

Minimum suggested boom heights for flat-fan nozzles, nozzle to target, as NDSU prints them for field sprayers
Spray angle 20 in spacing 30 in spacing
65 degrees 22 to 24 in 33 to 35 in
80 degrees 17 to 19 in 26 to 28 in
110 degrees 12 to 14 in 16 to 18 in
120 degrees 14 to 18 in, nozzle angled 35 to 45 degrees 14 in, nozzle angled

These are field-sprayer boom heights, not heights for a wand. A test-hall study of a mounted field-crop sprayer compared three nozzle types at boom heights of 0.30, 0.50 and 0.70 meters and found that both the nozzle type and the boom height changed the sprayer’s potential drift (2). I take two lessons from it for a wand: the nozzle matters, and so does how far it sits from the target.

Flat Fan Nozzle Droplet Size, Pressure and Drift

Every hydraulic nozzle makes a range of droplet sizes, and NDSU sums the range up with the volume median diameter, the size at which half the spray volume is in smaller droplets and half in larger ones (1).

What Pressure Does to the Droplets

NDSU says an extended range flat fan nozzle works over 15 to 60 PSI without a significant change in pattern width. Lower pressure gives larger droplets and less drift potential, while higher pressure gives fine drops with higher drift potential (1). Kansas State University Extension adds that droplets over 150 microns resist evaporation much more than smaller ones, and that higher pressures make many more droplets under 100 microns, so its author says to refrain from pressures above 40 to 45 psi (3). Both are guidance for farm and boom sprayers, so treat them as context and not as a setting for your wand. I give the full pressure explanation in my guide to reading PSI on a sprayer.

A laboratory test rig measured droplet size and speed for 32 combinations of nozzle and pressure and showed that the nozzle type, the nozzle size and the pressure each change the droplet spectrum. The same study warns that absolute numbers vary a lot with settings and equipment, so they are not directly comparable between tests (4). That is why I never quote a droplet number as a result for a given tip.

Pressure and Nozzle

A sprayer’s maximum pressure is the limit of the machine, not a setting to aim for. The product label and the nozzle’s maker decide the pressure and the nozzle for a job. Higher pressure makes more fine droplets that drift, and the nozzle you choose changes the droplet size.

Drift and the Weather

Drift is the other half of the droplet story, and the wind decides how far the fine droplets travel. The sources do not agree on one wind figure, so the safety note below names each one with its author.

Wind and Drift

Drift is spray carried off target by the air, and wind speed is the factor extension sources stress most. Their figures differ and none fits every situation, and your product label may be stricter than all of them. K-State Extension suggests spraying when the wind is under 10.1 miles per hour and says there is no maximum wind speed that fits every situation. LSU AgCenter says to avoid applying when the wind is above about 10 miles per hour. NC State says under 5 miles per hour when you calibrate with the product in the tank. Cornell gives no number and says not to take a chance by spraying in the wind. Do not spray during a temperature inversion, when cool air near the ground holds small droplets in the air, and do not assume that calm air, early morning or evening is suitable: check the actual conditions and follow every weather restriction on the product label. High temperature and low humidity make spray evaporate faster. Do not spray just before rain. Droplets smaller than about 150 micrometers drift most easily, and higher pressure makes more of them.

Flat Fan Nozzle Types and Uses

NDSU describes several nozzles that make a flat pattern, and each is built for a different job. The table keeps each one to what NDSU says about it (1).

Flat-pattern nozzle types as NDSU describes them for field sprayers
Type What NDSU says Pressure NDSU gives
Standard flat fan Widely used for broadcast spraying of herbicides and some insecticides; patterns must overlap Set by the nozzle’s own specifications
Extended range flat fan Keeps its pattern width over a range of pressures; works well with automatic spray controllers 15 to 60 PSI
Even flat fan Uniform coverage across the whole width; used for banding over the row, not for broadcast 30 to 40 PSI
Flood fan Wide-angle flat spray; pattern width changes more with pressure than a regular flat fan 10 to 25 PSI for least drift
Pre-orifice and air induction Two drift-reducing designs that make a flat-fan pattern Per the nozzle maker

Flat Fan Nozzle Uses

NDSU lists two uses: broadcast spraying with a standard or extended range tip and band spraying with an even tip (1). A flood tip is a wide-angle choice with a less uniform pattern. I read that as a reminder that every flat tip has a job, and the job comes from the label and the maker’s chart, not from the tip’s name.

Drift-Reducing Flat Fan Nozzle Design

NDSU explains two drift-reducing designs that still spray a flat fan. The pre-orifice nozzle has a chamber ahead of the final orifice that lowers the pressure at the outer orifice, which cuts the fine droplets. The air induction nozzle has two orifices and a venturi that draws air in, so the spray is large air-filled droplets with very few drift-prone ones (1).

A wind-tunnel test of five agricultural nozzles, including standard flat fans, pre-orifice and air induction designs, found median droplets up to 265% larger with the drift-reducing designs and up to 97.3% fewer droplets of 100 micrometers or less than with standard flat fans (5). Those were boom nozzles tested in one wind tunnel with water and a surfactant, so the result shows what the design can do on a test bench. It is not a promise for your wand.

Changing and Checking a Fan Nozzle Safely

A tip change puts your hands near the nozzle, the wand and the battery, so the safe state comes first. Complete the shutdown below before you swap a tip, open the tank, clean anything or check the pattern with water.

Full Shutdown Before You Touch the Tank or Nozzle

Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Shutdown before you open the tank, fill or refill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, lift, put on or take off a backpack unit, load, unload, move, transport, store or leave the sprayer. Never point the wand at yourself, another person or a pet. During normal spraying, move only as the equipment manuals and the product label permit; walking while spraying with a backpack unit, or driving a mounted boom at the spraying speed its manual describes, is operation, not transport. Never ride while operating a hand-held wand or lance. Battery sprayer (handheld or backpack): release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery and keep it away from the sprayer. Reconnect the power only after the work is complete, every part is secured and the pump switch is off. Some sprayers have no removable battery: the Smith Multi-Use 190671 and the Husqvarna 2-gallon handheld have a lithium-ion battery built into the pump, so their makers’ shutdown is to turn the pump off and operate the pressure release valve until no pressure remains in the tank, and you never open or take apart the sealed pump. A hand-pump sprayer has no battery: follow the same order through the pressure step with your manual’s procedure. If your manual prints no pressure-relief or power-isolation method, get the maker’s guidance before you open or loosen anything. Complete the shutdown before you walk away: never leave a sprayer pressurised, switched on or with its battery in. Wear the protective equipment the product label requires while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual; never clear a nozzle with your mouth and never by blowing into it. Add every step your manual gives, in its order. Refit every part, close the lid and check for leaks with clean water before product goes back in.

A Clean-Water Pattern Check

A water check shows you the sheet before any product goes in the tank. Do it with clean water only.

  1. Complete the full shutdown in the box above, including its emergency exception.
  2. Fit only a fan tip your sprayer’s manual lists for your exact model, in the way the manual describes.
  3. Before every use, check the tank, the strainer, the hose and the nozzle, and fix any leak before product goes in.
  4. Fill the tank with clean water and close the lid as your manual directs. Connect the power (install the battery, or switch on a pump with a built-in battery) only when you are ready to test, with every part secured and the pump switch off before you connect it.
  5. Aim the wand at bare paving or a bare wall, away from people, pets, windows and plants, and never test a spray against your hand. Run the sprayer and watch the sheet, the wand, the hose, the fittings and the tank seams for leaks without touching pressurized parts.
  6. Before you open the tank, correct a leak or add product, complete the full shutdown again. Follow your manual’s first-use steps.

On bare paving, I look first at the width of the sheet and second at its edges, which should read thinner than the middle on a standard flat fan. A sheet that is lopsided or has a streak in it tells me the tip needs the cleaning method in its manual before it goes anywhere near a plant.

Nozzle Swaps and the Maker’s Chart

The two manuals make the point strongly. For its V20 backpack sprayer, Craftsman says to always turn the switch to low when switching to a low-flow nozzle, and DEWALT’s manual for its DXSP190681 kit says to always turn the flow control knob to its low setting (1 to 3) when switching to a low-flow nozzle. Both manuals say that failing to follow the Nozzle Flow Chart may damage the pump and void the warranty. I keep the chart next to the tips, because the tip and the pump setting are one decision.

NC State Extension says to calibrate again whenever the application rate, the type of product or the nozzles change. Calibrate with clean water whenever you can, and my guide to calibrating a backpack sprayer shows how to measure your own output.

Cleaning, Strainers and Batteries

A plugged nozzle is one of the most frustrating problems with sprayers, NDSU says (1). Penn State and Iowa State advise cleaning strainers, screens and filters after every use. A tip change is a good moment to do both, once the full shutdown is complete.

Dedicated Sprayer

Illinois Extension advises a dedicated sprayer for the home orchard, one that has never been used for weed control products. Penn State and Iowa State warn that even small amounts of herbicide left in tanks, hoses, screens and fittings can harm crops, and that water alone is generally not enough to remove pesticide residue. Treat a sprayer that has held weed killer as a weed-killer sprayer, and keep a separate one for fruit trees, vegetables, ornamentals and liquid fertilizer.

Cleaning

Before you clean the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the label and your manual require. Clean the sprayer as soon as you can after use, because dried product is harder to remove than product still in solution. Empty the tank, rinse the tank, hose, wand and nozzle, and clean the strainers and screens, following the product label and your manual; extension guidance warns that water alone may not remove every product. Clean it away from desirable plants, wells and other water, and wash the outside. Do not pour leftover product or rinse water down a sink, a toilet or a storm drain, or onto bare ground.

Battery and Charger

Use only the battery and charger the maker supplies or lists for your exact sprayer, and charge, store and handle the battery only as your manual describes. To change or charge a removable battery, first complete the full shutdown in the shutdown box, including its emergency exception, which ends with removing the battery; begin the change or the charging only after that. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger, and follow the manual’s directions if a battery or charger gets wet. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using it without handling or removing it, keep people away and follow the battery manual’s emergency instructions; if it smokes or burns, move away and call 911 or the fire department.

The Label and Your Protective Equipment

Everything above holds for clean water. The moment a product goes into the tank, the product label rules the job, and the sprayer’s manual rules the machine. Read both.

The Label Is the Law

The product label is the law. It tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftover product and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. Your sprayer’s manual does not replace the label, and the label does not replace the manual: read the label before you open the container, and follow both.

Protective Equipment

Wear the protective clothing and equipment the product label requires, and put it on before you open the container. Wear the eye protection and gloves the label names every time you mix, load, spray, clean the tank or clear a nozzle. Cornell’s pesticide safety program also advises chemical-resistant gloves, goggles and a respirator when you handle moderately toxic products, even when the label does not call for them. Wear every respirator the label requires, of the type the label names, and follow the respirator maker’s instructions for fit, use and care. If you follow Cornell’s advice and wear one the label does not require, or if it is unclear which respirator or filter is right, get qualified guidance on the respirator and filter before you handle the product. Protective equipment lowers your exposure; it does not make spraying safe.

Mixing and Loading

Before you load the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the product label and your manual require for the task. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill or overflow cannot reach a well, a drain or other water. Read the label before you open the container, stand upwind, and do not eat, drink or smoke while you handle pesticides. Never use your mouth to siphon a pesticide from its container. Keep the fill hose above the level of the liquid in the tank so the product cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Use measuring tools kept only for pesticides, never kitchen utensils or food containers. Mix only as much as the job needs so the tank ends empty; do not store leftover mix in the sprayer for later, because it can damage the sprayer’s parts.

Amounts and Mixing

The product label, not this page, gives the amount of product, the dilution and the mixing order, so read it before you mix. Do not combine products unless the mixture complies with every product’s label and its compatibility has been established through the manufacturers or a qualified pesticide specialist; nobody’s advice overrides a label prohibition.

Children and Pets

Keep children, pets and other people out of the area while you mix, load and spray, and keep them off the treated area for as long as the label says. Before you spray, remove toys and take away or cover pet food and water dishes.

Storage

Before you store the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception. Store pesticides in their original containers, with the label on, locked up or under the control of a person who can keep others away, and out of the reach of children. Never put a pesticide in a container used for food, drink or household products. Keep pesticides away from food, animal feed and protective equipment, and store pesticides and fertilizers apart, because they can react with each other and start a fire. Store the sprayer drained, cleaned and dry, as your manual describes, with the battery stored as the battery manual describes.

Empty Containers and Leftover Product

Follow the product label’s instructions for rinsing the empty container, handling the rinse water and disposing of the container, and rinse only a container the label directs you to rinse. Add rinse water to a spray mixture only when the label permits it and the mixture can take it without exceeding the permitted fill level or changing the label-directed mixture. Never reuse an empty pesticide container for any purpose. For leftover product, follow the label’s disposal steps, or call your state pesticide agency or a household hazardous waste program.

Poison Help

If someone is exposed to a pesticide, follow the first-aid section of the product label and call Poison Control (America’s Poison Centers) at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.

A Fan Spray Nozzle for Pump Sprayer and Battery Sprayer Wands

Hand-pump and battery sprayers often ship with an adjustable cone nozzle and one or more fan tips. Alongside my comparison of battery sprayers and pump sprayers, Penn State Extension describes two nozzle uses with a backpack sprayer: sweeping an adjustable cone from side to side for broadcast application and using a conventional flat-fan nozzle for spot work. Before you fit or swap any tip, complete the full shutdown for your sprayer in the shutdown box above.

Fan Tips in the Box

The makers’ own manuals and pages differ on colors and names, so here is what each one lists. A red tip is not the same flow from one maker to the next, so read each maker’s own chart.

Fan tips that five battery sprayers list, as their makers name them
Sprayer Fan tips the maker lists Other tips listed
DEWALT DXSP190681 kit High-volume wide fan (brown), low-volume wide fan (red), low-volume narrow fan (yellow) Adjustable brass, foaming, jet stream
Craftsman V20 4-gallon Low-volume wide fan (red), low-volume narrow fan (yellow) Poly adjustable cone, foaming
Smith Multi-Use 190671 High-volume fan (red), low-volume fan (yellow) Adjustable cone, foaming
Husqvarna 2-gallon handheld High-volume fan (red), low-volume fan (yellow) Brass adjustable cone
PetraTools HD2000-S A fan tip named Fan Flat Nozzle Adjustable brass

Smith’s nozzle chart gives the red high-volume fan for large areas and the yellow low-volume fan for precision in confined areas. For the models in my comparison of DEWALT and Craftsman backpack sprayers, Craftsman prints a flow and pressure chart for its four nozzles, and DEWALT prints one for its six. Fit only the tips your maker lists for your model, never a tip from another maker’s kit.

A nozzle storage clip, which the DEWALT manual lists, keeps spare tips from rolling around the shed bench. On a sprayer without a clip, I keep spare tips in a labeled bag next to the sprayer.

One Bench Test of a Flat Fan Nozzle for Knapsack Sprayer Use

One bench experiment used a knapsack sprayer with six nozzle types: hollow cone, flat fan ceramic, flat fan ISO, CFA, AirMix and flat fan air induction. It ran them at 15 and 25 psi at a nozzle height of 50 centimeters and sampled the droplets on white cards. The hollow cone nozzle gave the best deposition and coverage, at 63% coverage, and the flat fan air induction nozzle gave the largest droplets, with a volume median diameter of about 378 micrometers (6). I explain the two cone types in my guide to hollow and full cone nozzles.

That is a single university experiment with a tracer on cards, and it is a measured example, not a ranking of brands. It shows that the pattern changes the result on a knapsack sprayer, which is the practical point for knapsack-sprayer work: the tip you fit changes what comes out.

Pressure Control on Hand-Pump and Battery Sprayers

NC State Extension says most backpack sprayers have pressure regulators that deliver the spray at a constant pressure, while few handheld sprayers do, and that a hand pump holds a fairly even pressure only when you work it at a constant number of strokes per minute. A regulator keeps a fan tip in its pressure range more easily, but the regulator is the maker’s design, not a finding. My comparison of backpack and handheld sprayers shows which one fits your yard.

I do not rank fan, cone or any other tip for a product or a plant. The label and the sprayer’s manual decide the nozzle, and no ranking changes that. If your label names a nozzle or droplet size, that line wins over anything on this page.

What to Remember About Fan Tips

Three points sum it up: a fan tip sprays a flat sheet with tapered edges, its angle and pressure shape the droplets, and the maker’s manual and the product label decide the tip and the pressure for your sprayer. My own tip is small and works: keep each tip with its chart, and run a clean-water pattern check on bare paving after every swap, once the full shutdown is complete. Next, read your sprayer’s nozzle chart and your label together. A fan tip is a flat, tapered-edge sheet of spray whose angle, pressure and overlap you set from the maker’s manual and the label.

Frequently Asked Questions

What is a flat spray nozzle?

A flat spray nozzle is a nozzle that sprays liquid as a flat sheet, usually called a flat fan nozzle. NDSU lists the flat fan as one of three basic spray patterns and says the standard flat fan has tapered edges, so neighboring patterns must overlap for even coverage.

What is the spray pattern of a flat fan nozzle?

The spray pattern of a flat fan nozzle is a flat, wide sheet, and on a standard tip it applies less liquid along the edges than in the middle. NDSU says most agricultural nozzles have angles from 65 to 120 degrees, and narrow angles give a more penetrating spray.

What is a flat fan nozzle used for?

A flat fan nozzle is used for broadcast spraying, which means covering a whole area. NDSU says standard flat-fan nozzles are widely used for broadcast spraying of herbicides and some insecticides, and even flat-fan nozzles are for banding over a row.

How does pressure change the droplet size of a flat fan nozzle?

Pressure changes droplet size because lower pressure makes larger droplets and higher pressure makes smaller ones. NDSU says higher pressure gives fine drops with higher drift potential, and Kansas State University Extension says droplets over 150 microns resist evaporation much more than smaller ones.

Can you use a flat fan nozzle on a pump sprayer?

You can use a flat fan nozzle on a pump sprayer when its manual lists or supplies a fan tip for that model. Penn State Extension describes a conventional flat-fan nozzle for spot work with a backpack sprayer, and several battery sprayers ship with fan tips. Fit only a tip your maker lists for your exact sprayer.

References

  1. Proulx R. Spray Equipment and Calibration. AE73. North Dakota State University Extension; revised October 2025.
  2. Balsari P, Gil E, Marucco P, van de Zande JC, Nuyttens D, Herbst A, Gallart M. Field-crop-sprayer potential drift measured using test bench: effects of boom height and nozzle type. Biosyst Eng. 2017;154:3-13.
  3. Wolf RE. Strategies to Reduce Spray Drift. MF-2444. Kansas State University Agricultural Experiment Station and Cooperative Extension Service; March 2000.
  4. Nuyttens D, Baetens K, De Schampheleire M, Sonck B. Effect of nozzle type, size and pressure on spray droplet characteristics. Biosyst Eng. 2007;97(3):333-345.
  5. McGinty J, Baumann P, Hoffmann W, Fritz B. Evaluation of the spray droplet size spectra of drift-reducing agricultural spray nozzle designs. Am J Exp Agric. 2016;11(3):1-5.
  6. Alheidary MHR. Influence of nozzle type, working pressure, and their interaction on droplets quality using knapsack sprayer. Iraqi J Agric Sci. 2019;50(3).

Safety Note: Read your sprayer’s manual and the product label before you open any container. The label is the law: it tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftovers and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. This page never gives an amount of product, a dilution or a mixing order: the label does. Wear the protective clothing and equipment the label requires, put it on before you open the container, and wear the eye protection and gloves it names whenever you mix, load, spray, clean the tank or clear a nozzle. Protective equipment lowers your exposure; it does not make spraying safe. Wear every respirator the label requires, of the type it names, and follow the respirator maker’s fit, use and care instructions. Before you clean or store the sprayer, or wire a 12V pump, complete the shutdown below first. Before you mix or load, complete the shutdown below, including its emergency exception. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill cannot reach a well, a drain or other water. Stand upwind, never use your mouth to siphon a product, keep the fill hose above the liquid so it cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Mix only what the job needs, and do not store leftover mix in the sprayer. Never point the wand at yourself, another person or a pet, and never test a spray against your hand. Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Otherwise, before you open the tank, fill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, load, unload, transport, store or leave the sprayer, or lift, put on or take off a backpack unit, complete the shutdown. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Battery sprayer: release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery. 12V vehicle sprayer: first stop and secure the vehicle as its manual directs, then release the trigger, close the wand or boom valve and switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies, and reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the label’s protective equipment while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual, never with your mouth and never by blowing into it. Refit every part and check for leaks with clean water before product goes back in. For the first water test, complete the shutdown first, fill the tank with clean water and close it as your manual directs, connect the power only when you are ready, and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts; complete the shutdown again before you open the tank, fix a leak or add product. Wind, heat and fine droplets carry spray off target: the label may be stricter than any extension guideline, and extension sources give different wind figures, so no single number fits every situation. Do not spray during a temperature inversion, and do not assume that calm air, early morning or evening is suitable. Do not spray just before rain. Keep children, pets and other people out of the area while you spray and off the treated area for as long as the label says, and remove toys and cover pet food and water dishes first. The label’s pollinator wording decides when you may spray around flowering plants, and early morning or evening is not automatically suitable. A sprayer that has held weed killer should stay a weed-killer sprayer: extension services advise a dedicated sprayer, and rinsing may not remove every residue. Follow the product label’s instructions for rinsing empty containers, handling rinse water and disposing of them, and never reuse an empty pesticide container; for leftover product, call your state pesticide agency or a household hazardous waste program, and never pour it down a sink, a toilet or a storm drain. Store pesticides in their original containers, locked up and out of the reach of children, away from food and animal feed, and keep pesticides and fertilizers apart. If someone is exposed, follow the first-aid section of the label, call Poison Control at 1-800-222-1222 and keep the label with you; call 911 in an emergency. If product spills, keep people and animals away and follow the label’s emergency directions; try to contain a small spill only if the label says that is safe and you have the protective equipment it requires, and otherwise get help (the emergency number on the label, Poison Control if anyone is exposed, 911 for a fire, immediate danger or a large spill). Use only the battery and charger the maker supplies or lists for your exact sprayer, charge and store the battery as your manual describes, and do not use a damaged battery or charger: lithium-ion batteries can overheat and catch fire. Wire a 12V pump the way your manual says and use the fuse it lists. On an ATV or UTV, wear the helmet and protective gear the Consumer Product Safety Commission recommends, get hands-on training, sit only in the positions the manufacturer designed, never ride with more passengers than there are seats, and in a UTV fasten the seat belts and keep every part of your body inside the vehicle; stay within the rack and tow capacity in your vehicle’s owner’s manual, and remember that sloshing liquid shifts weight and changes how the vehicle handles; Montana State University Extension advises against riding and spraying if you have to hold a wand or lance. Stop at once, complete the full shutdown and inspect if the sprayer leaks, loses pressure or runs without spraying, and restart only as the manual allows. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, do not handle or remove it: keep people away, follow the battery manual’s emergency instructions, and if it smokes or burns, move away and call 911 or the fire department. Before you fill the tank, complete the shutdown, and fill it only to the level your manual allows. Carrying a full tank is tiring: rest when you are tired.

Scroll to Top