A man adjusting the deflector shield on a broadcast spreader before use

What Is a Spreader Deflector? Edge Guards and Side Controls Explained

A spreader deflector is a shield or lever on a broadcast spreader that blocks or narrows part of the side throw of the spinning plate, and makers sell versions of it under different names, such as EdgeGuard, Side Spread Control and deflector shield. In large-scale production I verified seed drill calibration on weighing trays, so I read what a maker prints about a control before I trust it. This guide covers what the part is, how Scotts, EarthWay, Brinly and SOLO describe theirs, what each maker prints as its purpose, and how to handle one safely at a lawn edge.

What Is a Spreader Deflector?

A broadcast spreader, also called a rotary spreader, drops granules onto a spinning plate that throws them out to the sides. A deflector sits at the edge of that throw. Depending on the maker it is a flip-up shield, a lever on the hopper or a shield that sets the width of the throw. The makers describe it as a way to close or narrow one side of the fan, and the details differ from one spreader to the next. I cover its parts, forms and safe use in what a broadcast spreader is.

Scotts calls its version EdgeGuard. EarthWay calls its version Side Spread Control, a lever that shuts off one side. Brinly sells a flip-up side deflector, and SOLO fits a deflector shield on its chest-mount hand-crank spreader. Each maker prints a purpose for the part, whether it is a spreader edge guard or a plain shield, and none of them prints a measured result.

Key Point

A deflector is the maker’s control for one side of the throw. What it is for is the maker’s statement, and the product label and your spreader’s manual are the rules for using it.

You meet a deflector in two places: at the edge of the lawn, where the throw reaches a path, a bed or a drive, and in the spec list of the spreader you are about to buy.

Why a Broadcast Spreader Throws Past the Edge

A rotary plate throws granules in a fan, so the pattern is wider than the spreader itself. Clemson’s extension service says rotary spreaders “throw material in a swath much wider than the spreader”, which suits large areas, and Kentucky says they are less precise than drop spreaders.

The throw is also uneven across its width. NC State and Kentucky both describe a pattern that is heavier in the middle and lighter at the sides, which is why the passes have to overlap. Along a border, the lighter side of that fan is the part that reaches the path, the bed or the drive. A broadcast spreader with a deflector is the maker’s answer to that side. I explain what skews the pattern of a broadcast spreader in a separate guide.

My concrete work pad is 40 by 30 feet, the path to the house door is 4 feet wide and the gravel yard sits beside the lawn, so those are the edges I think about when I read about a side control.

Extension sources point to a different tool for a short, hard edge. UC IPM says to use drop spreaders rather than rotary spreaders to avoid off-target fertilizer application, Kentucky says drop spreaders reduce off-target application in beds, on sidewalks and in driveways, and NC State describes drop spreaders as having lower drift potential and more precise control of pattern edges. Those sources compare the two types, and none of them tests a deflector. The full comparison of broadcast and drop spreaders is its own topic.

Edge Guard, Side Spread Control and Deflector Shield: Three Names, One Idea

The same job carries a different name at each maker, so read the name and the side before you read anything else. Before you adjust, fit, flip or slide any of these parts by hand, or work a gate lever beside them, complete the stop and make-safe steps in the box below.

Safe-State Box: Stop and Make Safe First

Stop and make safe before you fill or unload the hopper, reach into the hopper, clear a clog, clean or rinse the spreader, lubricate it, adjust the gate or the pattern, change a part, move it, store it or leave it. Keep your hands, feet, hair and loose clothing away from the impeller, the plate, the agitator, the gears and the wheels while anything can turn. During normal spreading, walk only as your manual and the product label permit; walking behind a push spreader is operation, not transport.

Safe-State Order for Walk-Behind and Hand-Crank Spreaders

Walk-behind or hand-crank spreader: close the gate, then stop walking or cranking, and wait until the impeller, plate, agitator and wheels have stopped turning. Keep the gate closed while you fill. Wear all the protective equipment the product label and your manual require while you fill, clean or clear a jam. Clear a clog only with the method in your exact manual. Follow every applicable safety step in your manual, in the order it specifies. Refit every guard and cover, and check that the gate opens and closes before product goes back in.

Side controls as four makers print them on five models
Model Maker’s name Side covered How it is set Maker’s stated purpose
Scotts Turf Builder EdgeGuard DLX EdgeGuard Right Lever slid to “On” “to prevent product from spreading onto non-lawn areas”
EarthWay 2150 Commercial Side Spread Control Left Lever below the hopper slid to the back “to prevent fertilizer from being spread to the left side”
EarthWay 2600A-Plus SideSpread-Control Left Lever under the right side of the hopper slid front to back “shuts off left-side spreading”
Brinly P20-500BHDF-A Side deflector Left Knob loosened, flip-up shield rotated up or down “will keep material from moving towards left side of hopper”
SOLO 421 chest-mount crank Deflector shield and directional lever Lever: center, left or right Shield and lever set before moving Shield changes the width of spread

Scotts EdgeGuard on the DLX

The Scotts Turf Builder EdgeGuard DLX is a push broadcast spreader, and its guide labels the part on the parts diagram as the On/Off EdgeGuard Control. According to Scotts, a lever set to “On” “blocks off the right side of the spreader pattern to prevent product from spreading onto non-lawn areas.” To switch it on, the guide says to “slide lever to ‘On’ position.” I go through the lever, the trigger and the fit in my EdgeGuard DLX review.

A Scotts edge guard spreader is a one-sided design: the right side of the pattern is the side that closes, and the left stays open. The Scotts sheet describes the lever as a way to keep product off areas where it is not wanted, which is the maker’s purpose and not a measured result. I look at the parts diagram first, because the EdgeGuard lever sits on it next to the rate dial and the trigger.

EarthWay Side Spread Control

EarthWay uses its own term, Side Spread Control, and it works through a lever. On the 2600A-Plus the lever sits under the right side of the hopper and, according to EarthWay, it “shuts off left-side spreading”. The 2150 manual puts the lever “below the hopper” and has you slide it to the back “to prevent fertilizer from being spread to the left side.” Before you move a lever or fit a kit by hand, complete the stop and make-safe steps in the safe-state box above. Both manuals tell you to place the left wheel at a set distance from the border; that distance is the manual’s to give, so read it in your edition. I describe the whole spreader in my EarthWay 2600A-Plus spreader review.

When the pass is done, the manual says to close the gate lever and then slide the side control forward again “for a FULL, 180 degree spread pattern.” EarthWay says its control “eliminates” side deflectors on the 2150, and it still lists a separate Three Side Deflector Kit for that model.

The older 2016 edition of the 2150 manual does not describe a side control and shows a standard deflector option instead. The detail I check first on an EarthWay is the edition of the manual, because the 2016 text and the current text describe different parts. My EarthWay 2150 spreader review covers the 50 lb commercial push spreader.

The Brinly Side Deflector on a Push Spreader

The Brinly P20-500BHDF-A comes with a separate deflector kit. Complete the stop and make-safe steps in the safe-state box above before you tip, fit or turn any part of it. According to the manual, edition 1008066-F from 2022, the kit holds a shield, a mounting plate, fasteners and a knob, and the shield mounts on the left side of the hopper. The manual says the deflector “will keep material from moving towards left side of hopper,” and you engage or disengage it by loosening the knob and rotating the shield up or down.

That Brinly spreader deflector goes on during assembly: step 9 has you tip the spreader onto its right side and take two screws out of the left side of the hopper frame before the mounting plate goes on. What stands out to me in assembly step 9 is how much hardware the shield needs: two screws out of the frame, a mounting plate, a carriage bolt and a knob. Loosening the knob and turning the shield later is an adjustment, so complete the stop and make-safe steps in the safe-state box above first.

Brinly prints the spread width as up to 12 ft and adds that the width also depends on the volume, density and particle size of the material. The manual makes no statement that the shield keeps product off a path or a bed. The full P20 with its side deflector is in my Brinly spreader review.

The SOLO Deflector Shield on a Chest-Mount Crank

The SOLO 421 is a chest-mount hand-crank broadcast spreader, so you carry it and turn it by hand. Its manual names two controls for direction: a directional lever with center, left and right positions, and a deflector shield that changes the width of spread. The manual prints “180 degrees adjustable” for the direction range, and its set-up line reads “Set deflector to desired position. Adjust spreading direction lever to the desired position.” It adds that you can also change direction “simply by walking in the desired direction.” I look at the strap, the hopper and who should skip it in my SOLO 421 chest spreader review.

On a chest crank I give the carry as much attention as the shield, since a 1979 study of a hand-operated spinning spreader found that the carrying position changed how evenly it spread (1). That study covered one design, so it supports the principle and nothing more specific.

Not every spreader carries a side control. The Agri-Fab 45-0462 push spreader names no side deflector or edge control, and its manual tells the reader, when broadcasting weed control products, to make sure the broadcast pattern does not hit evergreen trees, flowers or shrubs. A spreader deflector kit is also a loose part: EarthWay’s Three Side Deflector Kit is sold apart for the 2150, so fit a kit only where your manual or the kit’s own instructions name your model. I give my verdict on the 130 lb model in my Agri-Fab 45-0462 spreader review.

How to Read a Listing That Mentions a Deflector

A listing or a spec sheet rarely tells you enough, so five checks decide what you are actually buying. The Brinly P20-500BHDF-A makes a good worked example, because its title, box and manual all mention the part. I set that Brinly against the Scotts model in my Scotts and Brinly spreaders comparison.

  1. Find the name. Brinly’s title says side deflector kit, Scotts says EdgeGuard and EarthWay says Side Spread Control.
  2. Find the side. The EarthWay manual places the left wheel near the border, so the covered side is the border side. Scotts closes the right, Brinly and EarthWay close the left. I compare the EdgeGuard DLX with the 2600A-Plus in my Scotts and EarthWay spreaders comparison.
  3. Find out whether it is built in, in the box or sold apart. The Scotts lever is on the parts diagram, the Brinly kit is in the box and the EarthWay 2150 kit is sold apart.
  4. Find the manual edition. Brinly’s manual is edition 1008066-F from 2022, and the EarthWay 2150 manual changed between 2016 and the current text.
  5. Read what the maker says it does, and stop there. For Brinly that is one sentence about material moving toward the left side of the hopper.

Applied to the Brinly, the five answers are: a side deflector kit by name, the left side, in the box, edition 1008066-F, and a purpose that covers one side of the hopper. That is five answers with no guesswork and nothing about a bed or a path. I run these five checks before I recommend any spreader with a side control. I skip any listing that says deflector without saying which side.

What a Deflector Does Not Fix

A deflector changes where the throw ends on one side. Other things change the pattern too, and the deflector does not touch them. Level, cleaning and calibration stay your job.

Level, Humidity and Residue

A test of tractor-mounted rotary fertilizer spreaders tilted from side to side found that the angle changed the pattern significantly (2). Brinly’s manual says the same thing in plain words: “Keep the impeller level when spreading.”

Humid air and residue on the impeller also shift a rotary spreader’s pattern, according to a laboratory study of turf spreaders (3). Brinly’s manual warns that “Excess material build-up can cause an uneven spread pattern” and says not to use the spreader on windy days, with no wind figure given. NC State adds that wind, slope, temperature and relative humidity all affect distribution, and that it is wise to delay application when conditions interfere. Spreaders also differ from one to the next: a field study of farm spreaders found a wide gap in how evenly different machines spread (4). I explain how the plate gets its throw in what a spreader impeller is.

I recommend you read each maker’s line as a purpose, and then check where the granules land on your own edge before you trust it.

Pace, Turns and the Gate

NC State says that generally only one wheel drives the impeller, so spreading through a turn changes the impeller’s speed and the pattern. Its advice is to start walking before you open the gate and to close it before you slow down, turn or stop. A laboratory test of a turf rotary spreader found that changing the travel speed changed the application rate significantly, and the author cautions that it covered one material and one spreader (5). I follow the granules from hopper to throw in how a broadcast spreader works.

Brinly’s manual says the same in capitals: “REMEMBER TO START AND STOP THE SPREAD WHILE MOVING.” It adds that opening the lever while stopped lets material run onto the ground without being spread. Close the gate before you stop, before you slow down to turn, and whenever you pause, and open it again only after you are walking or driving at the steady pace your manual describes. Do not spread while you turn.

Using a Deflector Safely Along a Lawn Edge

An edge asks more of you than open lawn, because the border is where people, pets, beds, drives and water sit. The steps below come from the product label, the spreader’s manual and the extension sources, and they apply to any spreader with a side control. Before you adjust, fill, clear or clean, complete the stop and make-safe steps in the safe-state box above.

Read the product label before you open the bag. Follow its directions for the permitted use, the application amount, protective equipment, weather, watering in, access by people and pets, storage and disposal. Using a registered pesticide in a way its label does not allow is against federal law. Follow the spreader’s manual too. If the product’s instructions and the spreader’s instructions cannot both be followed, do not use that combination; ask the manufacturers for guidance.

The manuals add their own rules. Brinly’s manual says to always wear eye protection, to wear substantial footwear and long trousers, never to operate the spreader barefoot or in open sandals, and not to let children or an untrained person operate it.

SOLO’s manual says to wear safety glasses or eye shields, closed toed shoes with good traction, snug long-sleeved clothes, tightly cuffed or cuffless pants and non-slip gloves, to wear a respirator if appropriate for the type of material being spread, and to tie long hair back; for chemicals it separately calls for protective clothing, a respirator and eye protection. SOLO also says not to let children use the spreader, not to load the hopper while carrying it and not to use accessory attachments the maker does not recommend, and Brinly says not to modify the machine or its safety devices.

Wear all the protective equipment the product label and your spreader’s manual require, and put it on before you open the bag. Wear it every time you fill the hopper, clean the spreader or clear a clog. Protective equipment lowers your exposure; it does not make handling a lawn product safe. Wash your hands before eating, drinking, smoking or using the restroom when you work with pesticides. Change your clothes and wash your hands immediately after you apply a product that contains a pesticide, and follow the label’s additional washing and clothing instructions.

No Rates Here

The product label gives the application directions, so read it before you set the gate. A setting listed for your exact spreader and product is a starting point, not proof of the amount delivered: follow the spreader’s manual and calibrate for the product, the spreader and the person using it before you apply. Never exceed the label’s application rate.

I recommend you put the stop and make-safe steps first every time, even for a quick tweak of a shield or a lever.

Filling and Spills

Before you fill or unload the hopper, complete the stop and make-safe steps for your spreader in the safe-state box, and keep the gate closed. For fertilizer, fill on a hard surface where spilled granules can be swept up, away from drains and water. Follow the product label’s handling and ventilation directions, and wear all the protective equipment the label and your manual require. Fill only to the level your manual allows, and secure the hopper cover or lid if your spreader has one. Keep children and pets away, and never leave a filled spreader where they can reach them.

Keep people and pets away from a spill. Follow the product label and its safety data sheet for collecting, reusing and disposing of spilled product, and wear the protective equipment they require. Never hose or wash granules into a street, a gutter, a drain, a ditch or water, and do not pile spilled product onto the lawn or return contaminated material to the bag. If you cannot manage the spill safely, stay away and call the emergency number on the label. Call Poison Control (America’s Poison Centers) at 1-800-222-1222 if anyone is exposed, and call 911 for a fire or immediate danger.

Runoff at Paths, Drives and Water

Keep fertilizer off pavement and out of drains and surface water. If scattered plain fertilizer lands on a sidewalk, a driveway or a patio, sweep it back onto the lawn before you water, without going over the label rate; collect a concentrated spill instead. For pesticide granules, follow the label’s cleanup instructions. Follow any buffer requirement that applies and keep fertilizer out of those areas. EPA advises against fertilizing before windy or rainy days, and Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Follow the product’s weather and watering directions too.

In a rainfall test on bermudagrass plots built to mimic golf fairways, phosphorus concentration and mass in the runoff were highest in the first simulated rainfall after a granular fertilizer and fell afterward (6). Those were fairway plots, so read the finding as direction. Drainage ditches border my property, so I tell readers to find the label’s buffer wording before they pick a spreader for an edge.

Keep children, pets and other people away from the area while you fill and spread, and keep them off the treated area for as long as the label says. Store the bag and the filled spreader where they cannot reach them. If someone swallows or is exposed to a lawn product, follow the first-aid section of the product label and call Poison Control at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.

Cleaning, Clogs and Storage for a Spreader With a Side Control

A side control adds a lever, a knob or a shield to the parts you have to keep clean and tight. Before you clean the spreader, complete the stop and make-safe steps in the safe-state box, and wear the protective equipment the product label and your manual require.

Handle leftover product, cleaning water and residues as the product label directs. Clean the spreader only by a method both the label and the manual permit, and rinse it only where they permit it, keeping product and contaminated wash water out of drains and water supplies. Dry the spreader completely, and lubricate it as its manual directs. If you change products, follow both products’ cleaning requirements: a rinse alone does not show that all residue is gone.

Fasteners Count

Brinly’s manual says to lubricate bearing surfaces periodically, to check all fasteners for tightness periodically and never to let material sit in the hopper for extended periods. The knob and the carriage bolt of the shield are fasteners too, so they belong on that check.

Never push, kick or dig product out of the gate or off the plate while anything can turn. If product clumps or bridges in the hopper or the gate clogs, stop and complete the stop and make-safe steps in the safe-state box first, then clear it only with the method in your manual.

Before you store the spreader, complete the stop and make-safe steps in the safe-state box. Store it empty, clean and dry, as your manual describes, with the gate closed. Keep products in their original labeled containers, securely closed, under the storage conditions their labels give, and away from children and pets. Lock pesticides away, apart from fertilizer, food and animal feed, and never put any product into a food or drink container. I recommend you keep the manual with the spreader, so the edition and the side of the control are on hand when you need them.

Choosing a Spreader With a Deflector

Remember three things. The Scotts, EarthWay and Brinly controls each close a stated side, the SOLO shield changes the width of spread, and the manual tells you which. Every claim about what the part achieves belongs to the maker, so level, clean and calibrate the spreader yourself, and the label and the manual set the rules at any edge. My tip: before the first fill, practice walking with the empty spreader and work the gate and the side control until the order is automatic, which is what Brinly’s manual asks for. A spreader deflector comes in several forms, so choose the spreader for the border you actually work along. If edge control decides your pick, my ranking of the push spreaders for fertilizer sorts models by edge control and kit.

Frequently Asked Questions

What is a deflector on a broadcast spreader?

A deflector on a broadcast spreader is a part that blocks or narrows part of the side throw of the spinning plate, according to the makers that sell one. Brinly’s flip-up side deflector on the P20-500BHDF-A mounts on the left side of the hopper and, per its manual, keeps material from moving toward that side. The label and the manual decide how and where you use it.

What is an edge guard on a spreader?

An edge guard on a spreader is a maker’s name for a side control that closes one side of the throw. On the Scotts Turf Builder EdgeGuard DLX, a lever set to On blocks off the right side of the pattern, according to Scotts. EarthWay’s version is called Side Spread Control and closes the left side.

What is a spreader deflector kit?

A spreader deflector kit is a loose set of parts that fits a named spreader. Brinly’s kit holds a shield, a mounting plate, fasteners and a knob, and EarthWay sells a separate Three Side Deflector Kit for the 2150. Fit one only as your manual or the kit’s instructions describe for your model.

How does a spreader deflector work?

A spreader deflector works by blocking or narrowing part of the side throw of the spinning plate, as the makers describe it. Brinly’s manual says its deflector “will keep material from moving towards left side of hopper”, and SOLO’s manual says its shield changes the width of spread. No maker prints a test result, so level, clean and calibrate your spreader as the manual says.

Does a broadcast spreader need a deflector?

A broadcast spreader does not have to carry a deflector, and your manual says whether yours has one built in, as an option or none. The Agri-Fab 45-0462 manual names none, while the Scotts DLX, the EarthWay 2150 and 2600A-Plus and the Brinly P20-500BHDF-A each carry one. Choose by the border you work along, and let the label’s buffer wording decide where any spreader may go.

References

  1. Wolf DD, Smith ES. Uniformity of seed and fertilizer distribution with a hand-operated spinning spreader. Trans ASAE. 1979;22(4):761-762.
  2. Yildirim Y. Effect of side to side spreader angle on pattern uniformity in single- and twin-disc rotary fertilizer spreaders. Appl Eng Agric. 2008;24(2):173-179.
  3. Parish RL. The effect of relative humidity on rotary turf spreader patterns. Appl Eng Agric. 1991;7(5):541-544.
  4. Crozier CR, Roberson GT. Granular fertilizer spreader swath uniformity achieved at varying target application rates. Crop Manag. 2014;13(1):1-6.
  5. Parish RL. The effect of speed on performance of a rotary spreader for turf. Appl Eng Agric. 1987;3(1):17-19.
  6. Shuman LM. Phosphorus and nitrate nitrogen in runoff following fertilizer application to turfgrass. J Environ Qual. 2002;31(5):1710-1715.

Safety Note: Read the product label and your spreader’s manual before handling product. Follow both; if their instructions cannot both be met, do not use that combination. Registered pesticide use must comply with its labeling. A listed spreader setting is a starting point; calibrate as the manual directs and never exceed the label rate. Wear all protective equipment required by the label and manual before opening the container and during filling, cleanup and jam clearing. Wash your hands before eating, drinking, smoking or using the restroom when working with pesticides. After application, change your clothes and wash your hands immediately, and follow the label’s additional washing and clothing instructions. Keep children, pets and other people away during handling and application and off treated areas for as long as the label requires. Emergency first: if a battery becomes unusually hot, swells, hisses, smells unusual or smokes, stop using the spreader without handling or removing the battery. Keep people away and follow the battery manual’s emergency instructions. If it smokes, burns or presents immediate danger, move away and call 911 or the fire department. Otherwise, complete the applicable stop and make-safe sequence before filling, unloading, reaching into the hopper, clearing a jam, cleaning, lubricating, adjusting, changing parts or batteries, hitching, unhitching, transporting, storing or leaving the spreader. Walk-behind or hand-crank: close the gate, stop walking or cranking, and wait for all moving parts to stop. Tow-behind: close the gate, stop the vehicle, set the parking brake, switch off the engine and remove the key as the vehicle manual directs, and wait for the wheels, impeller and agitator to stop before reaching into the hopper or touching the impeller. Battery spreader: release the trigger or close the gate, switch off, wait for moving parts to stop, then remove the battery as the manual directs and keep it away while working. Follow any additional isolation steps in the exact manual. Keep hands, feet, hair and loose clothing away from moving parts. Clear jams only by the manual’s method. Refit guards and covers and check the gate before refilling. With the spreader made safe and the gate closed, fill fertilizer on a hard surface where spills can be collected, away from drains and water. Follow the label’s handling and ventilation directions and the manual’s fill limit. Keep people and pets away from spills. Follow the label and safety data sheet for collection, reuse and disposal; do not spread concentrated spills onto the lawn or return contaminated product to its bag. Sweep scattered plain fertilizer from pavement onto the intended lawn before watering only without exceeding the label rate. Follow the label’s cleanup instructions for pesticide granules. Never wash product into streets, gutters, drains, ditches or water. Observe applicable buffers. EPA advises against fertilizing before windy or rainy days; Purdue advises against fertilizing drought-stressed, dormant or frozen turf. Close the gate before stopping or turning, as the manual directs. Follow both towing manuals for hitching, turning, slopes, speed and load limits; never ride on the spreader or carry passengers on it. Use only batteries specified for the model. Recharge rechargeable batteries only with a charger approved for them, as the manual directs; never recharge disposable cells. After completing the applicable shutdown, handle leftover product, cleaning water and residues according to the product label. Clean only by methods permitted by both label and manual, keeping contaminated water out of drains and water supplies. Rinse only if permitted, then dry and lubricate as directed. A rinse does not establish that all pesticide residue is gone. Use salt or ice melt only when the product directions and spreader manual permit it. Salt-based deicers can damage metal; follow the model’s cleaning instructions. Do not use lawn fertilizer to melt ice. Store the spreader empty, clean and dry as its manual directs. Keep products securely closed in their original labeled containers under their labels’ storage conditions, away from children and pets. Lock pesticides away, separate from fertilizer, food and feed; never use food or drink containers. For human exposure, follow the label’s first-aid instructions, call Poison Control at 1-800-222-1222 and keep the label available. Call 911 for immediate danger.

Scroll to Top