A woman driving an ATV with a 25-gallon spot sprayer, a larger 40-gallon unit parked near a barn

25 Gallon vs 40 Gallon ATV Sprayer: What the Bigger Tank Adds and Needs

The 25 gallon vs 40 gallon ATV sprayer choice comes down to what your vehicle’s owner’s manual lets the rack carry. A full 25 gallon tank holds about 209 pounds of plain water and a full 40 gallon tank about 334 pounds, before the sprayer itself is counted. I studied plant protection, so I read a tank size the way I read a nozzle chart: as a figure that has to match the job and the machine under it. Below you get the weight sum, the printed figures of two real Master Mfg units, the sloshing and slope rules, and the wiring and safety steps for both.

25 Gallon vs 40 Gallon ATV Sprayer at a Glance

Choose a tank only after your vehicle’s owner’s manual confirms the whole installed load, sprayer and mounting included; if that cannot be confirmed, neither unit is the right choice. The 40 gallon unit adds about 125 pounds of liquid and, on the maker’s printed figures, keeps the same pump, gun, hose and reach. That makes the larger tank a trade of fewer refill stops against more weight on the vehicle. Where the manual allows both, my recommendation for most property owners is the smaller tank. My guide to the ATV sprayer size you need works through tank size, rack load and surge.

Master Mfg Deluxe spot sprayers side by side
Row 25 gallon unit 40 gallon unit
Maker’s model number SSO-01-025D-MM SSO-01-040D-MM
Tank capacity, maker’s figure 25 gallons, polyethylene 40 gallons, polyethylene
Tank dimensions, maker’s figure 35.5 x 17.58 x 16.25 in 36 x 24 x 18.5 in
Pump, maker’s figure Everflo 12-volt on-demand diaphragm pump, 2.2 GPM Everflo 12-volt on-demand diaphragm pump, 2.2 GPM
Maximum pressure, maker’s ceiling Up to 70 PSI Up to 70 PSI
Spot spray reach, maker’s figure 25 ft vertical, 30 ft horizontal 25 ft vertical, 30 ft horizontal
Power, maker’s figure 12 volt vehicle supply, 10 ft harness with alligator clamps 12 volt vehicle supply, 10 ft harness with alligator clamps
Warranty, manual Two years, replacement parts only Two years, replacement parts only
Sprayer weight, empty Not listed Not listed
Plain water in a full tank, from USGS density About 209 lb About 334 lb

Everything above the last row is the maker’s printed figure for that model. The last row comes from the density of water that USGS publishes, worked out in the next section.

What a Full Tank Weighs

A full tank weighs what its water weighs, plus the sprayer. USGS gives the weight of water as 62.4 pounds per cubic foot, and a cubic foot holds about 7.5 US gallons, so a gallon of plain water weighs about 8.3 pounds. A mix of product and water is not plain water, and the label gives the mixing, so this page counts plain water only.

The Step From 25 to 40 Gallons

Twenty-five gallons of plain water come to about 209 pounds, and 40 gallons come to about 334 pounds. The extra 15 gallons therefore add about 125 pounds of liquid to the same vehicle. By the maker’s dimensions the 40 gallon tank is also larger in two directions, 24 by 18.5 inches against 17.58 by 16.25, so it asks for more rack space as well as more load capacity. My guide to 15 and 25 gallon sprayers covers tank size, weight and rack limits for the smaller pair.

I do the weight sum before I look at anything else on a spec table, because the sprayer’s own weight is not printed for either unit and the liquid is the part I can calculate. On a property like mine, with long orchard rows, the extra 15 gallons would save refill stops, and that is the only thing the bigger tank buys.

What One Vehicle Manual Prints

The vehicle’s owner’s manual, not the sprayer’s tank label, sets the load. As one example, Polaris prints a rear rack capacity of 180 pounds in the owner’s manual for its Sportsman 450 H.O., and says the rear rack capacity and the tongue weight must not exceed 180 pounds together. A full 25 gallon tank holds about 209 pounds of plain water, so on that one vehicle the water alone is above the printed rear rack figure before the sprayer is counted. Other ATVs and UTVs print other figures, and this example is no advice to load either tank on any vehicle.

Load Limit

Stay within the rack and tow capacity in your vehicle’s owner’s manual. Sloshing liquid shifts weight and changes how the vehicle handles: Montana State University Extension advises a spray tank with internal baffles and the lowest practical center of gravity, a boom that works as low to the ground as possible, and a rear-mounted boom or equipment that lowers the operator’s exposure.

What the Printed Figures Say About Each Tank

Two Master Mfg units are named here. Both run on 12 volts from the vehicle battery, so each is a vehicle-powered ATV tank sprayer and neither is a cordless battery sprayer.

The 25 Gallon ATV Sprayer

According to Master Mfg, the 25 gallon Deluxe spot sprayer (model SSO-01-025D-MM) has a polyethylene tank, a 15 foot hose and a deluxe spray gun with a trigger lock, and reaches 25 feet up and 30 feet out. The maker’s pump figure is the Everflo 12-volt on-demand diaphragm pump at 2.2 GPM and up to 70 PSI. For a buyer who wants a 25 gallon sprayer for ATV use, the open questions are the mounting kit, which Master Mfg sells separately, and the rack, which the vehicle’s manual decides.

I look at the tank dimensions first, because a tank has to fit the rack before its capacity matters.

The 40 Gallon ATV Sprayer

According to Master Mfg, the 40 gallon Deluxe spot sprayer (model SSO-01-040D-MM) carries the same pump, gun, hose and reach figures on a larger tank, and fits most UTVs and similar vehicles with light modifications. The manual covering this unit prints no mounting steps, so the 36 by 24 by 18.5 inch tank, the straps and the rack are the buyer’s job to match to the vehicle manual. The two-year warranty in the manual covers replacement parts only, and it is void if a corrosive or flammable chemical goes through the sprayer.

Sloshing, Baffles and Slopes

Liquid in a tank moves when the vehicle moves, and the bigger the tank, the more liquid moves. Montana State University Extension says that sloshing liquid in enough quantity can change ATV handling, and it advises choosing a spray system with the lowest practical center of gravity. I check the ground before I check the tank, since the tank size only matters once the slope is known.

What Baffles Do

Montana State University Extension advises a spray tank with internal baffles, which it says reduce liquid surges and improve stability when turning on slopes or hills. Before you buy any tank, ask the seller or the maker whether it has internal baffles. Confirm each model’s baffles and its suitability for your vehicle before you rely on either. My comparison of backpack and ATV sprayers shows what changes when a vehicle carries the tank.

On an ATV, follow its manual and your hands-on training for body position and for the slopes it permits with a sprayer load; Montana State’s advice for ATVs on a hill is to lean your body uphill, and body position does not guarantee protection against a rollover. In a UTV, stay properly restrained inside the vehicle and follow its manual’s slope limits. Research on ATV injuries has linked uphill travel to backward rollovers (1).

Spot Gun, Boom and Pump

Both Master Mfg units are spot sprayers: you pull the gun’s trigger and aim the nozzle at the plants, and the nozzle twists from a straight stream to a wide mist. Montana State University Extension advises not to ride and spray if you have to hold a wand or lance. I never hold the gun while the vehicle moves. Before you leave either unit unattended, complete the full shutdown for a 12V vehicle sprayer in the shutdown box below, including its emergency exception.

Adding a Boom to a 25 Gallon Unit

A 25 gallon ATV boom sprayer sends the liquid through a boom, an arm that carries nozzles, instead of one gun. Master Mfg sells boom and boomless kits for its spot sprayers separately, and its manual says to follow the separate boom kit manual for uniform coverage. The manual also says a pressure regulator, a pressure gauge and a shut-off valve come with select broadcast sprayers only, so a plain spot unit should not be assumed to have them. My guide to spot and boom sprayers compares which one fits your land and your label.

Montana State University Extension advises booms that can be operated as low to the ground as possible and rear-mounted booms on ATVs. A test-hall study of a mounted field-crop sprayer found that boom height and nozzle type both changed potential drift (2). That was a field-crop sprayer on a test bench, not an ATV unit, so read it as a reason to take boom height seriously and nothing more. A boomless ATV sprayer is a different kit on the same idea, and the maker’s own kit instructions describe it.

The pump is the same on both tanks. The North Dakota State University Extension publication on spray equipment says diaphragm pumps are commonly used with ATV sprayers (3). Its pump figures are for farm-scale sprayers and do not describe the small 12 volt pumps in these two units, which carry only the maker’s own 2.2 GPM and 70 PSI figures.

Wiring, Filling and the First Water Test

Before you wire, fill, rinse, move or service either unit, read the shutdown box once and follow it each time. It is written for a 12 volt vehicle sprayer, so it starts with the vehicle.

Full Shutdown Box

Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Shutdown before you open the tank, fill or refill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, move, store or leave the sprayer. Never point the wand at yourself, another person or a pet. During normal spraying, move only as the equipment manuals and the product label permit; walking while spraying with a backpack unit, or driving a mounted boom at the spraying speed its manual describes, is operation, not transport. Never ride while operating a hand-held wand or lance. 12V vehicle sprayer: first stop and secure the vehicle as its manual directs. Then release the trigger, close the wand or boom valve and switch the pump off at its switch. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies. Reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the protective equipment the product label requires while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual; never clear a nozzle with your mouth and never by blowing into it. Add every step your manual gives, in its order. Refit every part, close the lid and check for leaks with clean water before product goes back in.

Wiring the Pump

Before any wiring work on the pump, complete the full shutdown in the shutdown box, including its emergency exception and securing the vehicle. Wire the pump the way your sprayer’s manual says, and use the fuse the manual lists. To disconnect the supply, follow the shutdown box through securing the vehicle, stopping the pump and relieving the pressure, then disconnect it as your manual directs; reconnect it only after the work is complete, every part is secured and the pump switch is off.

The manual says to connect the red clamp to the battery’s positive post and the black clamp to the negative post, and warns that connecting the clamps to opposite posts makes the pump run backwards. I read that warning first on any 12 volt unit. The manual also says not to turn power on to the sprayer until you are ready to spray.

Filling and the First Water Test

Before the first water test, complete the full shutdown in the shutdown box, then fill the tank with clean water and close the lid as your manual directs. Connect the power (install the battery or connect the 12V supply) only when you are ready to test. Run the sprayer and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts. Before you open the tank, correct a leak or add product, complete the full shutdown again. Before every use, check the tank, strainer, hose and nozzle, and fix any leak before product goes in. Follow your manual’s first-use steps.

The same manual asks you to test with fresh water before adding chemicals, to check that the drain cap at the bottom of the tank is tight before filling, and to clean the suction strainer with fresh water while wearing rubber gloves. Before you fill either tank, confirm that your vehicle’s owner’s manual allows the whole installed load and that the sprayer is mounted as the manufacturers direct. If the tank shifts, complete the full shutdown in the shutdown box, including its emergency exception, before you inspect or adjust the mounting.

The Label, Protective Equipment and Mixing

The sprayer’s manual covers the machine, and the product label covers what goes in it.

The Label

The product label is the law. It tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftover product and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. Your sprayer’s manual does not replace the label, and the label does not replace the manual: read the label before you open the container, and follow both.

Protective Equipment

Wear the protective clothing and equipment the product label requires, and put it on before you open the container. Wear the eye protection and gloves the label names every time you mix, load, spray, clean the tank or clear a nozzle. Cornell’s pesticide safety program also advises chemical-resistant gloves, goggles and a respirator when you handle moderately toxic products, even when the label does not call for them. Wear every respirator the label requires, of the type the label names, and follow the respirator maker’s instructions for fit, use and care. If you follow Cornell’s advice and wear one the label does not require, or if it is unclear which respirator or filter is right, get qualified guidance on the respirator and filter before you handle the product. Protective equipment lowers your exposure; it does not make spraying safe.

A critical review of the research on protective clothing for agricultural pesticide users found that its real protection in working conditions may be over-estimated (4). A systematic review of 121 articles on handlers found goggles and gloves worn by fewer handlers than shirts and trousers (5). Those studies cover agricultural handlers, not home gardeners, and I read them as a reason to put the eye protection and gloves on every single time.

The product label, not this page, gives the amount of product, the dilution and the mixing order, so read it before you mix. Do not combine products unless the mixture complies with every product’s label and its compatibility has been established through the manufacturers or a qualified pesticide specialist; nobody’s advice overrides a label prohibition.

Mixing and Loading

Before you load the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the product label and your manual require for the task. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill or overflow cannot reach a well, a drain or other water. Read the label before you open the container, stand upwind, and do not eat, drink or smoke while you handle pesticides. Never use your mouth to siphon a pesticide from its container. Keep the fill hose above the level of the liquid in the tank so the product cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Use measuring tools kept only for pesticides, never kitchen utensils or food containers. Mix only as much as the job needs so the tank ends empty; do not store leftover mix in the sprayer for later, because it can damage the sprayer’s parts.

The maker’s manual adds its own limits: operators must be 16 years of age or older, and no flammable chemical such as diesel fuel and no corrosive chemical such as bleach may go in the sprayer. Its warranty is void if one does. Because a 40 gallon tank holds a larger volume of mix than a 25 gallon tank, mixing only as much as the job needs matters more with the bigger one.

Wind, Pressure and Riding on Spray Day

Spray day has three limits you control: the air, the pressure and the vehicle. Start with the air.

Wind and Drift

Wind and Drift

Drift is spray carried off target by the air, and wind speed is the factor extension sources stress most. Their figures differ and none fits every situation, and your product label may be stricter than all of them. K-State Extension suggests spraying when the wind is under 10.1 miles per hour and says there is no maximum wind speed that fits every situation. LSU AgCenter says to avoid applying when the wind is above about 10 miles per hour. NC State says under 5 miles per hour when you calibrate with the product in the tank. Cornell gives no number and says not to take a chance by spraying in the wind. Do not spray during a temperature inversion, when cool air near the ground holds small droplets in the air, and do not assume that calm air, early morning or evening is suitable: check the actual conditions and follow every weather restriction on the product label. High temperature and low humidity make spray evaporate faster. Do not spray just before rain. Droplets smaller than about 150 micrometers drift most easily, and higher pressure makes more of them.

On wind, the Master Mfg manual is stricter than the extension figures: it says never to spray when wind exceeds 4 MPH. The K-State publication also reports that higher pressure makes many more droplets under 100 microns (6), and those figures come from field and boom sprayers, so they are extension guidance and do not set an operating rule for an ATV spot gun. Wind is the check I make twice before the pump goes on.

Pressure and Riding

A sprayer’s maximum pressure is the limit of the machine, not a setting to aim for. The product label and the nozzle’s maker decide the pressure and the nozzle for a job. Higher pressure makes more fine droplets that drift, and the nozzle you choose changes the droplet size. Master Mfg’s up to 70 PSI is a ceiling, and it is the same for both tanks. My guide to reading PSI on a sprayer covers pressure, ranges and limits one by one.

ATV and UTV Riding

Wear the helmet and other protective gear the Consumer Product Safety Commission recommends, get hands-on training from a qualified instructor, and sit only in the positions the manufacturer designed for occupants. The CPSC says never to ride with more passengers than there are seats. In a UTV, fasten the seat belts and keep every part of your body inside the vehicle as its manual directs. The CPSC says riders younger than 16 should drive only age-appropriate youth model ATVs, never adult ATVs, and that off-road vehicles are designed for off-road terrain, not paved surfaces. Most ATVs seat one rider.

Keep children, pets and other people out of the area while you mix, load and spray, and keep them off the treated area for as long as the label says. Before you spray, remove toys and take away or cover pet food and water dishes.

Cleaning, Storage and Spills

A big tank makes cleaning a bigger job, so plan it before the first fill.

Dedicated Sprayer

Illinois Extension advises a dedicated sprayer for the home orchard, one that has never been used for weed control products. Penn State and Iowa State warn that even small amounts of herbicide left in tanks, hoses, screens and fittings can harm crops, and that water alone is generally not enough to remove pesticide residue. Treat a sprayer that has held weed killer as a weed-killer sprayer, and keep a separate one for fruit trees, vegetables, ornamentals and liquid fertilizer.

Cleaning

Before you clean the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the label and your manual require. Clean the sprayer as soon as you can after use, because dried product is harder to remove than product still in solution. Empty the tank, rinse the tank, hose, wand and nozzle, and clean the strainers and screens, following the product label and your manual; extension guidance warns that water alone may not remove every product. Clean it away from desirable plants, wells and other water, and wash the outside. Do not pour leftover product or rinse water down a sink, a toilet or a storm drain, or onto bare ground.

The manual says to drain excess product into a suitable container while wearing rubber gloves and eye protection, to flush the sprayer as the chemical manufacturer recommends, and never to store the sprayer with chemicals in the tank. For end-of-season storage it says to run RV anti-freeze through the system, and it says that letting the sprayer freeze without winterization voids the warranty.

Follow the product label’s instructions for rinsing the empty container, handling the rinse water and disposing of the container, and rinse only a container the label directs you to rinse. Add rinse water to a spray mixture only when the label permits it and the mixture can take it without exceeding the permitted fill level or changing the label-directed mixture. Never reuse an empty pesticide container for any purpose. For leftover product, follow the label’s disposal steps, or call your state pesticide agency or a household hazardous waste program.

Storage

Before you store the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception. Store pesticides in their original containers, with the label on, locked up or under the control of a person who can keep others away, and out of the reach of children. Never put a pesticide in a container used for food, drink or household products. Keep pesticides away from food, animal feed and protective equipment, and store pesticides and fertilizers apart, because they can react with each other and start a fire. Store the sprayer drained, cleaned and dry, as your manual describes.

If someone is exposed to a pesticide, follow the first-aid section of the product label and call Poison Control at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.

Spills

If product spills, keep people and animals away and follow the emergency directions on the product label and its safety data sheet. Try to contain a small spill only if the label says that is safe and you have the protective equipment it requires; when it is safe to do so, complete the shutdown before hands-on work on the sprayer. For a spill you can safely manage, use only absorbents and waste containers that are compatible with the spilled product, as its label, its safety data sheet or qualified emergency guidance specifies, and dispose of the collected waste as directed. If the spill is more than you can manage safely, call the emergency number on the label; call Poison Control at 1-800-222-1222 if anyone is exposed, and call 911 for a fire, immediate danger or a large spill.

Choose the 25 Gallon Unit or the 40 Gallon Unit

The choice follows the vehicle first and the job second, and if the manual cannot confirm the whole installed load for either tank, neither is the right pick. Both Master Mfg units print the same pump, pressure, reach and warranty figures, so the tank is the only real decision. My roundup of 12V ATV spot sprayers compares five units on tank, pump and hose specs.

Choose the 25 gallon unit if these fit you:

  • Your vehicle’s owner’s manual allows the whole installed load, with the sprayer’s own weight, the mounting and a full 25 gallon tank counted together.
  • You spray small jobs such as a fence line, a gravel yard or the strip under a drip line, where a refill is a short trip to the shed.
  • You want the smaller tank, which by the maker’s dimensions is the smaller of the two on the rack.

Choose the 40 gallon unit if these fit you:

  • Your vehicle’s owner’s manual allows the whole installed load, with the sprayer’s own weight and the mounting counted on top of about 334 pounds of plain water.
  • Your job is long and far from the water supply, so fewer refill stops matter more than the lighter load.
  • You have checked that the tank has internal baffles and that it fits the rack with its straps.

I pick the 25 gallon unit for most readers, and I keep the 40 gallon unit for the reader whose manual and job both point to it. My comparison of the 25 gallon Master Manufacturing sprayer and the Chapin 97254 sets the two side by side.

Pick the Tank Your Rack Can Carry

Three things matter more than the label on the tank. The vehicle’s owner’s manual sets the load, a full 25 gallon tank holds about 209 pounds of plain water and a full 40 gallon tank about 334 pounds, and the shutdown box comes before every hands-on step. My tip is to write the rack figure from your vehicle’s manual on a piece of tape on the tank before you shop, so the number is in front of you when the bigger tank looks tempting. The 25 gallon vs 40 gallon ATV sprayer decision is settled by that figure, and the sprayer’s pump, pressure and reach do not change it.

Frequently Asked Questions

What is the difference between a 25 gallon and a 40 gallon ATV sprayer?

The difference between a 25 gallon and a 40 gallon ATV sprayer is the tank: 15 more gallons, a larger tank body and about 125 more pounds of plain water when full. On Master Mfg’s two Deluxe spot sprayers the maker prints the same Everflo 2.2 GPM pump and up to 70 PSI for both. Your vehicle’s owner’s manual decides how much load the rack may carry.

Who makes a 40 gallon ATV sprayer?

Master Mfg makes a 40 gallon ATV sprayer in its Deluxe spot sprayer line, which the maker lists as model SSO-01-040D-MM with a 12-volt on-demand diaphragm pump. The maker says it fits most UTVs and similar vehicles with light modifications. Check the tank’s size and your vehicle’s owner’s manual before you buy.

What are baffles in an ATV sprayer tank?

Baffles in an ATV sprayer tank are the internal parts that Montana State University Extension says reduce liquid surges and improve stability when you turn on slopes or hills. The extension advises choosing a spray tank that has them. Ask the maker whether the tank you plan to buy has baffles.

Is a 40 gallon ATV sprayer worth it over a 25 gallon one?

A 40 gallon ATV sprayer is worth it over a 25 gallon one only when your vehicle’s owner’s manual allows the whole installed load, including the sprayer’s own weight and the mounting, and the extra 15 gallons saves refill stops on your job. The step adds about 125 pounds of plain water, and the maker’s printed pump and pressure figures stay the same. If the manual cannot confirm the load for the larger tank, it is not the right choice.

What is a 25 gallon ATV boom sprayer?

A 25 gallon ATV boom sprayer is a 25 gallon tank unit that sprays through a boom, an arm that carries nozzles, instead of a single spot gun. Master Mfg sells boom kits separately for its 25 gallon Deluxe spot sprayer and says to follow the separate boom kit manual for uniform coverage. Montana State University Extension advises rear-mounted booms on ATVs and booms that work as low to the ground as possible.

References

  1. Brandenburg MA, Brown SJ, Archer P, Brandt EN. All-terrain vehicle crash factors and associated injuries in patients presenting to a regional trauma center. J Trauma. 2007;63(5):994-999.
  2. Balsari P, Gil E, Marucco P, van de Zande JC, Nuyttens D, Herbst A, Gallart M. Field-crop-sprayer potential drift measured using test bench: effects of boom height and nozzle type. Biosyst Eng. 2017;154:3-13.
  3. Proulx R. Spray Equipment and Calibration. AE73. North Dakota State University Extension; revised October 2025.
  4. Garrigou A, Laurent C, Berthet A, et al. Critical review of the role of PPE in the prevention of risks related to agricultural pesticide use. Saf Sci. 2020;123:104527.
  5. Sapbamrer R, Thammachai A. Factors affecting use of personal protective equipment and pesticide safety practices: a systematic review. Environ Res. 2020;185:109444.
  6. Wolf RE. Strategies to Reduce Spray Drift. MF-2444. Kansas State University Agricultural Experiment Station and Cooperative Extension Service; March 2000.

Safety Note: Read your sprayer’s manual and the product label before you open any container. The label is the law: it tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftovers and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. This page never gives an amount of product, a dilution or a mixing order: the label does. Wear the protective clothing and equipment the label requires, put it on before you open the container, and wear the eye protection and gloves it names whenever you mix, load, spray, clean the tank or clear a nozzle. Protective equipment lowers your exposure; it does not make spraying safe. Wear every respirator the label requires, of the type it names, and follow the respirator maker’s fit, use and care instructions. Before you clean or store the sprayer, or wire a 12V pump, complete the shutdown below first. Before you mix or load, complete the shutdown below, including its emergency exception. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill cannot reach a well, a drain or other water. Stand upwind, never use your mouth to siphon a product, keep the fill hose above the liquid so it cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Mix only what the job needs, and do not store leftover mix in the sprayer. Never point the wand at yourself, another person or a pet, and never test a spray against your hand. Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Otherwise, before you open the tank, fill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, load, unload, transport, store or leave the sprayer, or lift, put on or take off a backpack unit, complete the shutdown. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Battery sprayer: release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery. 12V vehicle sprayer: first stop and secure the vehicle as its manual directs, then release the trigger, close the wand or boom valve and switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies, and reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the label’s protective equipment while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual, never with your mouth and never by blowing into it. Refit every part and check for leaks with clean water before product goes back in. For the first water test, complete the shutdown first, fill the tank with clean water and close it as your manual directs, connect the power only when you are ready, and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts; complete the shutdown again before you open the tank, fix a leak or add product. Wind, heat and fine droplets carry spray off target: the label may be stricter than any extension guideline, and extension sources give different wind figures, so no single number fits every situation. Do not spray during a temperature inversion, and do not assume that calm air, early morning or evening is suitable. Do not spray just before rain. Keep children, pets and other people out of the area while you spray and off the treated area for as long as the label says, and remove toys and cover pet food and water dishes first. The label’s pollinator wording decides when you may spray around flowering plants, and early morning or evening is not automatically suitable. A sprayer that has held weed killer should stay a weed-killer sprayer: extension services advise a dedicated sprayer, and rinsing may not remove every residue. Follow the product label’s instructions for rinsing empty containers, handling rinse water and disposing of them, and never reuse an empty pesticide container; for leftover product, call your state pesticide agency or a household hazardous waste program, and never pour it down a sink, a toilet or a storm drain. Store pesticides in their original containers, locked up and out of the reach of children, away from food and animal feed, and keep pesticides and fertilizers apart. If someone is exposed, follow the first-aid section of the label, call Poison Control at 1-800-222-1222 and keep the label with you; call 911 in an emergency. If product spills, keep people and animals away and follow the label’s emergency directions; try to contain a small spill only if the label says that is safe and you have the protective equipment it requires, and otherwise get help (the emergency number on the label, Poison Control if anyone is exposed, 911 for a fire, immediate danger or a large spill). Use only the battery and charger the maker supplies or lists for your exact sprayer, charge and store the battery as your manual describes, and do not use a damaged battery or charger: lithium-ion batteries can overheat and catch fire. Wire a 12V pump the way your manual says and use the fuse it lists. On an ATV or UTV, wear the helmet and protective gear the Consumer Product Safety Commission recommends, get hands-on training, sit only in the positions the manufacturer designed, never ride with more passengers than there are seats, and in a UTV fasten the seat belts and keep every part of your body inside the vehicle; stay within the rack and tow capacity in your vehicle’s owner’s manual, and remember that sloshing liquid shifts weight and changes how the vehicle handles; Montana State University Extension advises against riding and spraying if you have to hold a wand or lance. Stop at once, complete the full shutdown and inspect if the sprayer leaks, loses pressure or runs without spraying, and restart only as the manual allows. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, do not handle or remove it: keep people away, follow the battery manual’s emergency instructions, and if it smokes or burns, move away and call 911 or the fire department. Before you fill the tank, complete the shutdown, and fill it only to the level your manual allows. Carrying a full tank is tiring: rest when you are tired.

Scroll to Top