A woman spraying crops on foot with a backpack sprayer, an ATV with a mounted spot sprayer in background

Backpack Sprayer vs ATV Sprayer: What Changes When a Vehicle Carries the Tank

The backpack sprayer vs ATV sprayer choice comes down to who carries the tank: your back or a vehicle. A battery backpack sprayer holds a few gallons and goes anywhere you can walk, while a 12V ATV sprayer holds more liquid and needs a vehicle, a mounting spot and a power connection. I trained in plant protection, so I read the product label and the sprayer manual before I judge any machine. Below I compare the two, what a vehicle changes, and where the safety rules sit.

Backpack Sprayer vs ATV Sprayer: The Short Answer

A backpack sprayer is the right tool when the job is a walk: tree-row strips, fence corners, the edges of a gravel yard. An ATV sprayer is a bigger tank, a pump and a wand or boom bolted to a vehicle and run from its 12V supply, so it suits ground where the vehicle already goes and where refilling a small tank would become the main work. My guide to powered garden sprayers lists the types, parts and safety basics.

  • Backpack sprayer: you carry the tank, the pump is battery or hand powered (this comparison uses a battery model), and the limit is the size of the tank and your back.
  • ATV sprayer: the vehicle carries the tank, its 12V supply runs the pump, and the limit is the vehicle, the mount and the ground it can cross safely.
  • Both: the product label sets the rules for the liquid, and the sprayer manual sets the rules for the machine.

Key Takeaway

I tell readers to choose by the route and by the vehicle they already own. If the job is a walk, I carry the tank. If the job is wide, repeated and on ground the vehicle crosses safely, a mounted unit makes sense, and its extra risk comes from liquid moving on a vehicle.

What Each Sprayer Is and How It Is Powered

Both machines do the same basic job: a pump pushes liquid from a tank through a hose to a wand or nozzle. What differs is where the tank sits and where the power comes from. Backpack sprayers can be hand pumped or battery powered (my guide to battery and manual backpack sprayers covers that split), and this comparison uses a battery backpack and a 12V mounted sprayer.

The Battery Backpack Sprayer

The EGO BSP3500 is a 56V lithium-ion cordless backpack sprayer with a 4 gallon tank, and my review of the EGO sprayer goes through its tool-only kit. It is sold as a tool only, so the battery and charger are not included, and EGO says in its manual that the sprayer is for horticultural and agricultural use only. It rides on a harness with shoulder straps, a chest buckle and a waist buckle, and EGO’s manual says the pack should sit closer to your hips than to your shoulders. According to EGO, a speed dial sets the flow rate and a lock-on lever holds the trigger.

I like that the whole machine moves with me. In my orchard rows, which run toward the farm yard, a backpack walks one side of a row and then the other without a vehicle in the way. That freedom is the reason I recommend a backpack for strip and spot work. My guide to backpack versus handheld sprayers helps you pick the one that fits your yard.

The 12V ATV Spot Sprayer

The Chapin 97200E is a 12 volt, 15 gallon ATV sprayer that mounts on an ATV, a UTV or a lawn tractor. It has no battery of its own: according to Chapin’s manual it runs from a 12 volt vehicle supply through a wire harness with an in-line fuse. Its pump is a two chamber diaphragm pump, and NDSU Extension notes that diaphragm pumps are commonly used with ATV sprayers, in farm-size versions much larger than this one.

The spot unit is the form most people picture first. A wand on a hose does the spraying, and the tank stays on the rack. Other mounted units add a boom, and Montana State University Extension advises that an ATV be fitted only with a rear-mounted spray boom or other equipment that lowers the operator’s exposure, with the boom working as low to the ground as possible. An ATV boom sprayer is a different build from a spot unit, and I read its own manual for the boom width and nozzle count before I trust any figure on a sales page. I list five 12V models with their tank, pump and hose specs in my roundup of the best ATV spot sprayers.

Tank, Pump and Wand Compared

The table sets two named models side by side so the difference between a carried and a mounted sprayer is visible in printed figures. Each figure is the maker’s, for that model only, and neither column is a ranking.

EGO BSP3500 battery backpack sprayer and Chapin 97200E 12V ATV sprayer
Feature EGO BSP3500 Chapin 97200E
Type Battery backpack sprayer 12V ATV/UTV mounted spot sprayer
Power source 56V lithium-ion battery, battery and charger not included 12 volt DC from a vehicle battery, in-line fuse in the wire harness
Tank capacity, maker’s figure 4 gallons 15 gallons
How it is held Harness with shoulder straps, chest buckle and waist buckle Designed to be attached to stable surfaces, per the manual
Pump, maker’s description Pump type not published by the maker Two chamber diaphragm pump, self priming
Spray control Speed dial for flow rate, adjustable nozzle on the wand Pressure changes only by adjusting the nozzle, per the manual
Weight, dry without battery 16.8 lb Not published by the maker

According to the makers, the EGO holds 4 gallons and the Chapin 15 gallons, and a bigger tank is the reason the mounted unit exists. Chapin’s manual says the pump switch shuts the pump off at 60 PSI and that pressure can be changed only by adjusting the nozzle. EGO prints its pressure as a ceiling, up to 350 PSI as the maker prints it, and a ceiling is the limit of the machine and never a setting to aim for. My guide on what PSI means for sprayers shows how to read a pressure ceiling like that.

What Changes When the Tank Rides on a Vehicle

A vehicle adds three things a backpack never has: moving weight, a rider, and a wand that someone may be tempted to hold while the vehicle moves. Each one has its own rule. My comparison of 25 versus 40 gallon sprayers shows what the bigger tank adds and needs.

Moving Liquid Changes How the Vehicle Handles

Load, Surge and Slopes

Stay within the rack and tow capacity in your vehicle’s owner’s manual. Sloshing liquid shifts weight and changes how the vehicle handles: Montana State University Extension advises a spray tank with internal baffles and the lowest practical center of gravity, a boom that works as low to the ground as possible, and a rear-mounted boom or equipment that lowers the operator’s exposure. On an ATV, follow its manual and your hands-on training for body position and for the slopes it permits with a sprayer load; Montana State’s advice for ATVs on a hill is to lean your body uphill, and body position does not guarantee protection against a rollover. In a UTV, stay properly restrained inside the vehicle and follow its manual’s slope limits. Research on ATV injuries has linked uphill travel to backward rollovers (1).

In one regional trauma-center series, most ATV crashes involved a rollover. That sample is one hospital and a mix of work and recreation, so it is not a national rate and not about sprayer loads. I read it as a reason to respect slope and weight, and I do not read it as a number to plan around.

Chapin’s manual says the 97200E has been designed to be attached to stable surfaces. It prints no vehicle load figure, no baffle figure and no slope figure, so the vehicle’s own manual is the only place those limits live. A 15 gallon tank is also a bigger liquid load than most people picture when they lift a 4 gallon backpack tank. My guide to the ATV sprayer size you need sets tank size against rack load and surge.

Riding Rules Come From the Vehicle

ATV and UTV Riding

Wear the helmet and other protective gear the Consumer Product Safety Commission recommends, get hands-on training from a qualified instructor, and sit only in the positions the manufacturer designed for occupants. The CPSC says never to ride with more passengers than there are seats. In a UTV, fasten the seat belts and keep every part of your body inside the vehicle as its manual directs. The CPSC says riders younger than 16 should drive only age-appropriate youth model ATVs, never adult ATVs, and that off-road vehicles are designed for off-road terrain, not paved surfaces. Most ATVs seat one rider.

A Hand Wand and a Moving Vehicle Do Not Mix

Montana State University Extension advises not to ride and spray if you have to hold a wand or lance. A spot sprayer such as the Chapin comes with a hand wand, so the practical meaning is that the vehicle stops, is secured as its manual directs, and only then does the wand come out. I do not recommend spraying from a moving vehicle with a hand wand. Walking while spraying with a backpack unit is normal operation, and a vehicle does not change that rule for the walking sprayer.

The Label, Protective Equipment and Drift Apply to Both

Neither sprayer changes the rules for the liquid in the tank. A pesticide label is a legal document, and it decides the equipment, the weather and the timing for your site, whichever machine applies it.

The Label

The product label is the law. It tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftover product and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. Your sprayer’s manual does not replace the label, and the label does not replace the manual: read the label before you open the container, and follow both.

In my orchard the dormant oil spray at silver tip and the first fungicide at open flower are label and weather jobs before they are sprayer jobs. My flowering strips of phacelia, white clover and buckwheat are no-spray areas, and the label’s pollinator wording decides the rest. The same order of thinking applies whether the tank is on your back or on a rack. My roundup of the battery sprayers for fruit trees lists seven backpack models for home orchards.

Protective Equipment Comes First

Protective Equipment

Wear the protective clothing and equipment the product label requires, and put it on before you open the container. Wear the eye protection and gloves the label names every time you mix, load, spray, clean the tank or clear a nozzle. Cornell’s pesticide safety program also advises chemical-resistant gloves, goggles and a respirator when you handle moderately toxic products, even when the label does not call for them. Wear every respirator the label requires, of the type the label names, and follow the respirator maker’s instructions for fit, use and care. If you follow Cornell’s advice and wear one the label does not require, or if it is unclear which respirator or filter is right, get qualified guidance on the respirator and filter before you handle the product. Protective equipment lowers your exposure; it does not make spraying safe.

Your sprayer’s manual adds its own requirements. EGO’s manual for the BSP3500 says to wear eye protection with side shields or goggles marked to comply with ANSI Z87.1, breathing and skin protection, gloves, and heavy long pants and boots. Chapin’s manual for the 97200E says to always wear goggles, gloves, a long sleeve shirt, long pants and full foot protection when spraying. Wear the stricter of the label and the manual.

A critical review of coverall studies in OECD countries found that the real-world effectiveness of protective equipment may be over-estimated (2). A study of 32 backpack-sprayer applications by Nicaraguan farmers found that work practices and the spray equipment explained more of the skin exposure than clothing and hygiene did, and it noted leaking or poorly sealed tanks among the determinants (3). That sample was Nicaraguan farmers scored by eye, so it points to work practice and equipment as large parts of exposure without telling a US home gardener what to expect.

Wind, Droplets and Pressure

Wind and Drift

Drift is spray carried off target by the air, and wind speed is the factor extension sources stress most. Their figures differ and none fits every situation, and your product label may be stricter than all of them. K-State Extension suggests spraying when the wind is under 10.1 miles per hour and says there is no maximum wind speed that fits every situation. LSU AgCenter says to avoid applying when the wind is above about 10 miles per hour. NC State says under 5 miles per hour when you calibrate with the product in the tank. Cornell gives no number and says not to take a chance by spraying in the wind. Do not spray during a temperature inversion, when cool air near the ground holds small droplets in the air, and do not assume that calm air, early morning or evening is suitable: check the actual conditions and follow every weather restriction on the product label. High temperature and low humidity make spray evaporate faster. Do not spray just before rain. Droplets smaller than about 150 micrometers drift most easily, and higher pressure makes more of them.

K-State’s and LSU’s wind figures come from field and boom spraying, so I treat them as extension guidance and never as a rule for a backpack wand. NC State’s figure of under 5 miles per hour is guidance for calibration with the product in the tank, while my guide to calibrating a backpack sprayer explains how to measure your own output. Kansas State’s publication adds that droplets over 150 microns resist evaporation much more than smaller ones and that higher pressures make many more droplets under 100 microns (4).

Pressure and Nozzle

A sprayer’s maximum pressure is the limit of the machine, not a setting to aim for. The product label and the nozzle’s maker decide the pressure and the nozzle for a job. Higher pressure makes more fine droplets that drift, and the nozzle you choose changes the droplet size.

Keep children, pets and other people out of the area while you mix, load and spray, and keep them off the treated area for as long as the label says. Before you spray, remove toys and take away or cover pet food and water dishes.

Filling, First Water Test and Shutdown for Both Sprayers

Every hands-on job with a sprayer starts from the same safe state, and the safe state differs a little between a battery unit and a 12V vehicle unit. I put the full shutdown first because every mistake I worry about begins with a hand near the tank, the nozzle or the battery.

Full Shutdown Box

Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Shutdown before you open the tank, fill or refill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, move, store or leave the sprayer. Never point the wand at yourself, another person or a pet. During normal spraying, move only as the equipment manuals and the product label permit; walking while spraying with a backpack unit, or driving a mounted boom at the spraying speed its manual describes, is operation, not transport. Never ride while operating a hand-held wand or lance. Battery sprayer (handheld or backpack): release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery and keep it away from the sprayer. 12V vehicle sprayer (ATV, UTV, cart or tow-behind): first stop and secure the vehicle as its manual directs. Then release the trigger, close the wand or boom valve and switch the pump off at its switch. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies. Reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the protective equipment the product label requires while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual; never clear a nozzle with your mouth and never by blowing into it. Add every step your manual gives, in its order. Refit every part, close the lid and check for leaks with clean water before product goes back in.

Neither the EGO manual nor the Chapin manual prints a pressure-relief procedure for these models. Get the maker’s own pressure-relief procedure before you open or loosen anything on either one.

Mixing and Loading Outdoors

Before you load either sprayer, the shutdown box above comes first, and the label comes before the container opens.

Mixing and Loading

Before you load the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the product label and your manual require for the task. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill or overflow cannot reach a well, a drain or other water. Read the label before you open the container, stand upwind, and do not eat, drink or smoke while you handle pesticides. Never use your mouth to siphon a pesticide from its container. Keep the fill hose above the level of the liquid in the tank so the product cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Use measuring tools kept only for pesticides, never kitchen utensils or food containers. Mix only as much as the job needs so the tank ends empty; do not store leftover mix in the sprayer for later, because it can damage the sprayer’s parts.

The Amount Is on the Label

The product label, not this page, gives the amount of product, the dilution and the mixing order, so read it before you mix. Do not combine products unless the mixture complies with every product’s label and its compatibility has been established through the manufacturers or a qualified pesticide specialist; nobody’s advice overrides a label prohibition.

EGO’s manual for the BSP3500 says: do not combine chemicals. Any mixture must also comply with every product label and with the exact manual of the sprayer you use.

Filling and Carrying

Before you open or fill the tank, complete the full shutdown in the shutdown box. Then fill only to the level your manual allows and, for a carried sprayer, only to a weight you can handle with the straps and hip belt adjusted as the manual describes. Before you lift, put on or take off a backpack unit, or load, unload, transport or leave the sprayer, complete the full shutdown again. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Carrying a full tank is tiring work: rest when you are tired, and stop before you lose your footing.

I stop and rest when my arms tire, and I never carry on with a sore back.

First Water Test and Pre-Use Check

First Water Test

Before the first water test, complete the full shutdown in the shutdown box, then fill the tank with clean water and close the lid as your manual directs. Connect the power (install the battery or connect the 12V supply) only when you are ready to test. Run the sprayer and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts. Before you open the tank, correct a leak or add product, complete the full shutdown again. Before every use, check the tank, strainer, hose and nozzle, and fix any leak before product goes in. Follow your manual’s first-use steps.

I treat the clean water run as the first job with any sprayer, ahead of any product, and I open the manual’s troubleshooting page before the first fill. Chapin’s manual lists leaks at the pump head or switch in its troubleshooting table, and EGO’s manual says to inspect the whole product for damaged, missing or loose parts before each use.

Battery, Charger and 12V Wiring

Battery and Charger

Use only the battery and charger the maker supplies or lists for your exact sprayer, and charge, store and handle the battery only as your manual describes. To change or charge a battery, first complete the full shutdown in the shutdown box, including its emergency exception, which ends with removing the battery; begin the change or the charging only after that. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger, and follow the manual’s directions if a battery or charger gets wet. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using it without handling or removing it, keep people away and follow the battery manual’s emergency instructions; if it smokes or burns, move away and call 911 or the fire department.

A review of thermal runaway modelling says safety concerns from thermal runaway constrain wider use of lithium-ion batteries (5), and OSHA’s fact sheet for workplaces lists following the manufacturer’s instructions for storage, use, charging and maintenance as a control (6). Neither source is about garden tools, so the exact manual stays the authority for a backpack unit.

12V Wiring

Before any wiring work on the pump, complete the full shutdown in the shutdown box, including its emergency exception and securing the vehicle. Wire the pump the way your sprayer’s manual says, and use the fuse the manual lists. To disconnect the supply, follow the shutdown box through securing the vehicle, stopping the pump and relieving the pressure, then disconnect it as your manual directs; reconnect it only after the work is complete, every part is secured and the pump switch is off.

Chapin’s manual warns that the wiring harness must not become pinched or damaged, because a pinched harness may overheat, and its fuse is an in-line fuse in the harness. That is the part of a mounted unit that a backpack never asks of you, and I route the harness away from rack edges before the first test run. The manual prints the replacement fuse rating, and it is the manual’s figure that matters, never a general rule.

Cleaning and Storing Each Sprayer

Cleaning and storage follow the same two layers as everything else: the product label for the liquid and the sprayer manual for the machine. Both start with the shutdown box.

Dedicated Sprayer

Illinois Extension advises a dedicated sprayer for the home orchard, one that has never been used for weed control products. Penn State and Iowa State warn that even small amounts of herbicide left in tanks, hoses, screens and fittings can harm crops, and that water alone is generally not enough to remove pesticide residue. Treat a sprayer that has held weed killer as a weed-killer sprayer, and keep a separate one for fruit trees, vegetables, ornamentals and liquid fertilizer.

Cleaning

Before you clean the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception, and wear the protective equipment the label and your manual require. Clean the sprayer as soon as you can after use, because dried product is harder to remove than product still in solution. Empty the tank, rinse the tank, hose, wand and nozzle, and clean the strainers and screens, following the product label and your manual; extension guidance warns that water alone may not remove every product. Clean it away from desirable plants, wells and other water, and wash the outside. Do not pour leftover product or rinse water down a sink, a toilet or a storm drain, or onto bare ground.

EGO’s manual says not to leave residue or spray material in the tank after use, and Chapin’s manual says to flush the pump with water after use because some chemicals will damage the pump valves if they soak untreated for a long period. Chapin also says to store the tank upside down in a warm, dry location, while EGO says to store the sprayer indoors in a well-ventilated place with the tank empty. Both makers drain the liquid first. My guide to storing a sprayer battery shows what nine maker manuals print.

Storage

Before you store the sprayer, complete the applicable full shutdown in the shutdown box, including its emergency exception. Store pesticides in their original containers, with the label on, locked up or under the control of a person who can keep others away, and out of the reach of children. Never put a pesticide in a container used for food, drink or household products. Keep pesticides away from food, animal feed and protective equipment, and store pesticides and fertilizers apart, because they can react with each other and start a fire. Store the sprayer drained, cleaned and dry, as your manual describes, with the battery stored as the battery manual describes.

I recommend a locked room or cabinet for product, away from food and feed, with the sprayer drained and dry beside it.

Exposure

If someone is exposed to a pesticide, follow the first-aid section of the product label and call Poison Control (America’s Poison Centers) at 1-800-222-1222, and keep the product label with you. Call 911 in an emergency.

When a Backpack Stops Being Enough

A backpack stops being enough when refilling and carrying become the main work, and a vehicle unit takes over when the ground and the route suit a vehicle. The tank size, the number of refills and your own back decide where that line falls. My guide to the backpack sprayer size you need matches tank size to the yard and the job.

The printed tank figures show the size of the step. The EGO holds 4 gallons and the Chapin 15 gallons, and the carried unit asks you to lift and wear its liquid, which is why the filling rule above ends with resting when you are tired. A vehicle unit moves that load to the rack, and it brings the rollover, riding and wiring rules in exchange. Montana State’s advice that bigger and faster is not always better, and that a smaller machine is easier to move by hand, is worth keeping in mind here. My comparison of 15 versus 25 gallon sprayers covers tank size, weight and rack limits.

One boundary sits above all of this. Where the label forbids a use, such as the product on that site, in that weather or on that crop, no sprayer is the answer, and a bigger tank or a vehicle unit is never a workaround. The label wins every time, and the sprayer only does what the label allows.

Choosing by Job and Vehicle

Three things to remember: the label sets the rules for the liquid, the shutdown comes before any hand goes near the tank, and a vehicle adds weight, riders and a wand that must never be held while moving. My tip is to run clean water through whichever sprayer you buy before any product goes in. Pick the carried unit for walking jobs, pick the mounted unit only if your vehicle, its manual and your ground all agree, and keep the backpack sprayer vs ATV sprayer decision tied to the route you actually walk or drive. My list of the best battery powered backpack sprayers compares seven picks by fit and battery.

Frequently Asked Questions

What is the difference between a backpack sprayer and an ATV sprayer?

A backpack sprayer is carried on your back and its pump may be battery or hand powered, while an ATV sprayer is mounted on a vehicle and, in the 12V form compared here, run from its supply. The EGO BSP3500 battery backpack holds 4 gallons and the Chapin 97200E holds 15 gallons, according to the makers. The vehicle adds moving liquid, riding rules and wiring that a backpack never has.

What is an ATV sprayer?

An ATV sprayer is a tank, a pump and a wand or boom that mounts on an ATV, a UTV or a similar vehicle. According to Chapin’s manual, the 97200E runs from a 12 volt vehicle supply through a wire harness with an in-line fuse. It has no battery of its own.

What changes when the spray tank rides on an ATV instead of your back?

The tank’s liquid moves with the vehicle, so sloshing shifts weight and changes how the vehicle handles. Montana State University Extension advises a tank with internal baffles, the lowest practical center of gravity and a boom that works as low to the ground as possible. Stay within the rack capacity in the vehicle’s owner’s manual.

What safety rules apply when you spray from an ATV?

Wear the helmet and protective gear the Consumer Product Safety Commission recommends, get hands-on training, and never ride with more passengers than there are seats. Montana State University Extension advises not to ride and spray if you have to hold a wand or lance. Follow the product label and the vehicle’s manual for everything else.

When does a backpack sprayer stop being enough?

A backpack sprayer stops being enough when refilling and carrying the tank become the main work of the job. The tank size, the number of refills and your own back decide that point, and the vehicle must suit the ground. Where the label forbids a use, no sprayer is the answer.

References

  1. Brandenburg MA, Brown SJ, Archer P, Brandt EN. All-terrain vehicle crash factors and associated injuries in patients presenting to a regional trauma center. J Trauma. 2007;63(5):994-999.
  2. Garrigou A, Laurent C, Berthet A, et al. Critical review of the role of PPE in the prevention of risks related to agricultural pesticide use. Saf Sci. 2020;123:104527.
  3. Blanco LE, Aragon A, Lundberg I, Liden C, Wesseling C, Nise G. Determinants of dermal exposure among Nicaraguan subsistence farmers during pesticide applications with backpack sprayers. Ann Occup Hyg. 2005;49(1):17-24.
  4. Wolf RE. Strategies to Reduce Spray Drift. MF-2444. Kansas State University Agricultural Experiment Station and Cooperative Extension Service; March 2000.
  5. Wang G, Ping P, Kong D, et al. Advances and challenges in thermal runaway modeling of lithium-ion batteries. Innovation (Camb). 2024;5(4):100624.
  6. Occupational Safety and Health Administration. Lithium-ion Battery Safety. Fact Sheet DTSEM FS-4480. US Department of Labor; January 2025.

Safety Note: Read your sprayer’s manual and the product label before you open any container. The label is the law: it tells you what protective equipment to wear, how and where you may use the product, what weather it allows, how long to stay out of the treated area, how long to wait before you harvest, how to protect bees and other pollinators, and how to dispose of leftovers and the empty container. Using a registered pesticide in a way its label does not allow is against federal law. This page never gives an amount of product, a dilution or a mixing order: the label does. Wear the protective clothing and equipment the label requires, put it on before you open the container, and wear the eye protection and gloves it names whenever you mix, load, spray, clean the tank or clear a nozzle. Protective equipment lowers your exposure; it does not make spraying safe. Wear every respirator the label requires, of the type it names, and follow the respirator maker’s fit, use and care instructions. Before you clean or store the sprayer, or wire a 12V pump, complete the shutdown below first. Before you mix or load, complete the shutdown below, including its emergency exception. Mix and load outdoors, away from other people (including children), pets and livestock, and where a spill cannot reach a well, a drain or other water. Stand upwind, never use your mouth to siphon a product, keep the fill hose above the liquid so it cannot siphon back into your water supply, and never leave the sprayer unattended while you fill it. Mix only what the job needs, and do not store leftover mix in the sprayer. Never point the wand at yourself, another person or a pet, and never test a spray against your hand. Emergency first: if a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, stop using the sprayer without handling or removing the battery, keep people away and follow the battery manual’s emergency instructions; if it smokes, burns or presents immediate danger, move away and call 911 or the fire department without finishing the routine shutdown. Otherwise, before you open the tank, fill it, change or clean a nozzle, clear a clogged nozzle, clean or rinse the sprayer, adjust or repair anything, charge or change the battery, load, unload, transport, store or leave the sprayer, or lift, put on or take off a backpack unit, complete the shutdown. During normal spraying, move only as your manual and the product label permit, and never ride while operating a hand-held wand or lance. Battery sprayer: release the trigger or close the wand valve, then switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then remove the battery. 12V vehicle sprayer: first stop and secure the vehicle as its manual directs, then release the trigger, close the wand or boom valve and switch the pump off. Relieve all trapped pressure using only your exact manual’s procedure and a discharge destination consistent with the product label, without opening the tank or loosening any part beforehand unless that procedure expressly requires it, and never toward yourself, another person or an animal. Then disconnect the pump’s 12V supply at the connection your manual specifies, and reconnect it only after the work is complete, every part is secured and the pump switch is off. Wear the label’s protective equipment while you clean the tank, the strainer or a nozzle. Clear a clogged nozzle only with the method in your exact manual, never with your mouth and never by blowing into it. Refit every part and check for leaks with clean water before product goes back in. For the first water test, complete the shutdown first, fill the tank with clean water and close it as your manual directs, connect the power only when you are ready, and watch the wand, hose, fittings and tank seams for leaks without touching pressurized parts; complete the shutdown again before you open the tank, fix a leak or add product. Wind, heat and fine droplets carry spray off target: the label may be stricter than any extension guideline, and extension sources give different wind figures, so no single number fits every situation. Do not spray during a temperature inversion, and do not assume that calm air, early morning or evening is suitable. Do not spray just before rain. Keep children, pets and other people out of the area while you spray and off the treated area for as long as the label says, and remove toys and cover pet food and water dishes first. The label’s pollinator wording decides when you may spray around flowering plants, and early morning or evening is not automatically suitable. A sprayer that has held weed killer should stay a weed-killer sprayer: extension services advise a dedicated sprayer, and rinsing may not remove every residue. Follow the product label’s instructions for rinsing empty containers, handling rinse water and disposing of them, and never reuse an empty pesticide container; for leftover product, call your state pesticide agency or a household hazardous waste program, and never pour it down a sink, a toilet or a storm drain. Store pesticides in their original containers, locked up and out of the reach of children, away from food and animal feed, and keep pesticides and fertilizers apart. If someone is exposed, follow the first-aid section of the label, call Poison Control at 1-800-222-1222 and keep the label with you; call 911 in an emergency. If product spills, keep people and animals away and follow the label’s emergency directions; try to contain a small spill only if the label says that is safe and you have the protective equipment it requires, and otherwise get help (the emergency number on the label, Poison Control if anyone is exposed, 911 for a fire, immediate danger or a large spill). Use only the battery and charger the maker supplies or lists for your exact sprayer, charge and store the battery as your manual describes, and do not use a damaged battery or charger: lithium-ion batteries can overheat and catch fire. Wire a 12V pump the way your manual says and use the fuse it lists. On an ATV or UTV, wear the helmet and protective gear the Consumer Product Safety Commission recommends, get hands-on training, sit only in the positions the manufacturer designed, never ride with more passengers than there are seats, and in a UTV fasten the seat belts and keep every part of your body inside the vehicle; stay within the rack and tow capacity in your vehicle’s owner’s manual, and remember that sloshing liquid shifts weight and changes how the vehicle handles; Montana State University Extension advises against riding and spraying if you have to hold a wand or lance. Stop at once, complete the full shutdown and inspect if the sprayer leaks, loses pressure or runs without spraying, and restart only as the manual allows. If a battery becomes unusually hot, swells, hisses, gives off an unusual odor or smokes, do not handle or remove it: keep people away, follow the battery manual’s emergency instructions, and if it smokes or burns, move away and call 911 or the fire department. Before you fill the tank, complete the shutdown, and fill it only to the level your manual allows. Carrying a full tank is tiring: rest when you are tired.

Scroll to Top