A man pressure washing a concrete driveway with an upright electric pressure washer

How to Use a Pressure Washer: The Order the Manuals Give, Step by Step

How to use a pressure washer comes down to one order: read the manual, turn the water on, purge and start the machine in the order the manual prints, spray with the trigger lock on whenever you stop, then stop, release the trapped pressure and drain it. The manuals for gas, corded and battery washers share that frame and differ in the details, so I follow the manual of the exact machine in front of me.

My plant protection training taught me to read the label and the manual before I open anything, and that habit is the whole method here. Below you get the order, the safety rules that come first and the points where the makers disagree.

How to Use a Pressure Washer: The Order the Manuals Follow

Westinghouse, Greenworks and EGO all open their instructions with the same demand: read the manual before you use the machine. After that the order is water first, because each of them says not to run the pump without the water supply connected and turned on; the purge and the start then follow each maker’s own order. The box below is the safety floor for every step where a hand goes near a hose, a nozzle, the gun or the machine.

Stop and Make Safe

Emergency first, for a washer with a battery: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Stop and make safe before you connect or disconnect a hose, change a nozzle, wand or accessory, clear a clogged nozzle, clean a filter, add detergent, refuel, check the oil, charge or change a battery, drain the washer, move it, store it or leave it. Release the trigger and engage the trigger lock on the spray gun. Gas washer: turn the engine off with its switch as the manual says and wait until all moving parts have stopped. Let the engine and the muffler cool for the time your manual gives before you refuel, store the washer or touch hot parts, and disconnect the spark plug wire before maintenance where your manual directs it. Corded electric washer: turn the washer off with its power switch and wait until all moving parts have stopped. Battery washer: turn the washer off and wait until all moving parts have stopped. Every washer, after the steps above for your type: follow your manual’s water-supply shutdown and pressure-relief procedure. Point the gun away from people, pets and electrical equipment at a discharge location your manual and the detergent label permit. Disengage the trigger lock, squeeze the trigger to relieve the trapped pressure as the manual directs, then engage the lock again. Then unplug a corded washer by the plug, not by the cord, with dry hands, or remove the battery from a battery washer as your manual directs and keep it away from the washer while you work. Do not disconnect hoses or change nozzles before the pressure is relieved. If the manual’s procedure does not release the pressure, stop and get service; do not loosen a fitting to release it. Only then disconnect hoses or change nozzles. Where your manual gives a different order for these steps, follow your manual’s order. Follow every applicable step in your manual, in the order it specifies, and check that every hose, fitting and nozzle is attached and undamaged before water or power goes back on.

The steps below all put a hand near the machine at some point, so each one starts from that box.

  1. Read the manual for your exact model and follow its warnings before anything in this article.
  2. Connect the garden hose with the faucet off, after you flush it and look at the inlet screen.
  3. Connect the high-pressure hose and the gun, and fit the nozzle your manual names.
  4. Turn the water on, then purge the air and start the machine in the order your manual prints. Squeeze the trigger with the gun pointed in a safe direction until the stream is steady, which is how the manuals purge the pump and the hose.
  5. Spray with both hands on the gun, firm footing and the trigger lock engaged whenever you stop.
  6. Stop in the manual’s order and relieve the trapped pressure before you disconnect anything.
  7. Drain the machine, clean up and store it as the manual directs.

The manuals differ on the details of steps 2 to 7, and where a manual gives its own order I follow the manual’s order.

How to Use a Pressure Washer Safely: Rules Before the First Start

Read the pressure washer’s manual before you connect water or power, and follow it. Its warnings, its operator rules and its steps for your exact model come before anything in this article. Greenworks and Westinghouse both rule out use when you are tired or under the influence of alcohol or drugs.

The Stream Is the Main Hazard

Spray at People

Never point the spray at yourself, another person, a pet or any part of the body. Keep your hands and feet away from the nozzle and the stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury.

The reason is the injection injury: a jet can drive water or detergent through the skin of a hand, and a case report on a pressure washer injury describes infection, compartment syndrome and in some cases amputation (1). In US emergency department data, pressure washers account for most hand injection injuries, with cases clustered in late spring and summer (2). One finger injury at close range needed emergency surgery although the X-ray showed no fracture (3). I treat the nozzle end of a washer as a place my hand never goes, even when the machine seems idle.

Eyes, Feet and Ears

Wear safety glasses or goggles and closed footwear when you operate the washer, and put them on before you start; where your manual requires goggles, side shields or a face shield, that requirement replaces the minimum here. Follow the manual’s additional protective-equipment requirements, including hearing protection where the manual requires it, and the detergent label’s requirements when you handle detergent. Keep your hands and feet away from the spray. Protective equipment does not make contact with the stream safe.

The Westinghouse gas manual asks for safety goggles or glasses with side shields, a full face shield as necessary and full ear protection, Greenworks asks for goggles or glasses with side shields and a full face shield as necessary, and the ePX3500 manual rules out bare feet, sandals and open-toed shoes. A three-patient case series reports open and blunt eye injuries after pressure washer use, all treated surgically, with poor final vision in all three (4). Separately, NIOSH measurements on landscaping crews found significantly more noise from fuel-powered outdoor tools than from battery versions (5). I put the goggles on before I touch a starter or a power button, and with a gas machine I add ear protection from the first pull.

Trigger Lock, Two Hands and Footing

Engage the trigger lock on the spray gun whenever you stop spraying, even for a moment, before you set the gun down, and before you walk away or change position. Disengage the lock only for controlled spraying or for the manual’s pressure-relief procedure, with the gun pointed in a safe direction. Westinghouse’s gas manual says never to use a gun with a damaged or altered trigger lock or to secure the trigger in the spray position.

Hold and brace the spray gun as your manual instructs, keep firm footing on a surface that is not slippery, and follow your manual’s warning about the push of the gun when you squeeze the trigger. Start the stream away from your feet and from anyone else, and never swing the gun toward people or pets as you turn. The ePX3500 label reads “The spray gun kicks back- Hold firmly with two hands,” and Greenworks and EGO also say both hands.

Do not use a pressure washer for a task at height, such as from a ladder, unless your manual expressly permits the equipment and the method. Westinghouse’s gas manual adds that a kickback at height could cause a serious fall. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Then I engage the lock and squeeze the trigger once to confirm it holds, the check the ePX3500 manual prints, before I do anything else with the gun.

Keep children, pets and other people away from the work area while the machine runs, and never let a child use the machine. Store the washer and its battery or fuel where children cannot reach them.

Setting Up for the First Time

If you are learning how to use a pressure washer for the first time, setup is where most of the manuals’ warnings sit, because assembly, the power supply and the water supply all come before the first squeeze of the trigger. Greenworks puts it plainly: do not power on before the product is assembled completely. If you are still choosing a machine, my roundup of pressure washers for home use covers corded and battery models.

Where the Machine Goes

Gas Washer Exhaust

Operate a gas pressure washer outdoors, never inside a building or a partly enclosed space. CDC says to keep it at least 20 feet from any window, door or vent, and your manual may set a stricter placement, which you follow. Engine exhaust contains carbon monoxide, which you cannot see or smell and which can kill. Opening a door or a window does not make it safe to run an engine inside. If anyone develops symptoms such as headache, dizziness, weakness, nausea or confusion, move to fresh air and get emergency medical care.

Modeling of a small gasoline engine found that carbon monoxide can climb to dangerous levels within minutes in an enclosed room, and the authors concluded that small gasoline engines should not run inside buildings or in semi-enclosed spaces (6). Westinghouse’s gas manual names garages, basements, crawlspaces and sheds as places never to run it. Picture a machinery shed with a concrete floor: a gas washer stays outside, however handy the shelter looks.

Corded Washer Electricity

Use the electrical supply and the GFCI protection your manual specifies, and test the GFCI before use according to its instructions. If the washer trips a GFCI or a circuit breaker while you use it, stop using it and have a qualified repair person examine it before you use it again; do not keep resetting it and carry on. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Never cut or splice a power cord or an extension cord. Wear closed, rubber-soled footwear that gives some electrical insulation, plus any additional footwear the manual requires; footwear does not replace GFCI protection or the other electrical precautions. Use an extension cord only if your manual permits it, and then only the type and length it names. Keep every plug and cord connection dry, out of standing water and away from runoff and the area you are washing, and keep the spray away from outlets, wiring and electrical equipment. Do not use a damaged cord or plug.

The corded manuals do not agree on cords. Westinghouse’s ePX3500 manual says never to use an extension power cord, while Greenworks allows only extension cords intended for outdoor use and rated at least as high as the washer. I set the corded manuals beside the battery ones in my comparison of battery versus corded washers.

Battery Washer

Use only the battery and the charger the maker specifies for your exact pressure washer, and charge, store and handle them only as your manual describes. Before you change or charge the battery, follow the emergency exception and the applicable stop and make-safe steps in the safe-state box. Lithium-ion batteries can overheat and catch fire (thermal runaway), so do not use a damaged battery or charger. If you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a battery, stop using it and follow your battery manual’s emergency instructions.

EGO’s HPW3200 manual, the twin of the HPW3204-2 kit, asks you to make sure the pack latch snaps into place before you start, and I listen for that click before I press the power button.

Connecting the Water

Before you inspect parts or connect hoses, complete the applicable stop and make-safe steps in the safe-state box. Inspect the high-pressure hose, the spray gun and every fitting before each use, as your manual describes, and do not use a damaged part. Replace a damaged high-pressure hose; never repair or patch it. Connect the hoses and turn on the water before you start the machine, and purge and start it in the order your manual specifies.

Water supply, as each maker prints it
Item Westinghouse gas (WPX2700, WPX3200, WPX3400) Westinghouse ePX3500 Greenworks GPW3002A EGO HPW3200
Flush the garden hose first Run water through it for 30 seconds Flush for several seconds Let it flow for 30 seconds Run it for 30 seconds
Free hose before the faucet At least 10 feet Not listed At least 10 feet Not listed
Inlet screen Inspect screen and gasket; do not use if damaged Never connect the hose without the screen in place Inspect the filter; do not use if damaged Check the metal mesh in the inlet port
Water source A pressurized water spigot; no pool or lake water A water main; no lake, pool or pond The water main; no pond or lake water A garden hose, or a bucket through the siphon hose and filter
Drinking-water mains and backflow Not listed Some places may bar a direct connection; a backflow preventer or receiver tank is generally permitted Not suitable for the drinking-water mains without a backflow preventer; follow local regulations Not intended for the potable water mains; no hose coupling with Aquastop or any backflow preventer on the washer’s water connection

Every one of these manuals also says cold water only, and you follow the drinking-water and backflow line of your own manual before you connect. I built the drip irrigation on the farm with a 150-mesh disc filter at the pump head, so the washer’s inlet screen is the part I read about first. I also uncoil the garden hose in a straight line before I attach it, so a kink shows before the washer is involved. If you have seen the machine sold under the other name, my pressure washer and power washer guide explains what the two names really mean.

The Westinghouse gas manual, the ePX3500 manual and Greenworks all say a damaged high-pressure hose is replaced, never repaired. EGO warns that a loose connection at either end of that hose may cause a burst under high pressure and injury, so tighten both before each use.

Purging Air and Starting a Gas, Corded or Battery Washer

Water goes on before power on every washer, and each maker prints its own purge. The Westinghouse gas manual says not to start the engine until a steady stream flows from the nozzle, Greenworks says to pull the trigger to release air pressure before it connects power, and EGO installs the battery and presses the power button before it has you squeeze the trigger for a steady stream. Keep the gun pointed in a safe direction while you do it.

Gas: Engine Switch, Fuel Valve, Choke and Recoil

A gas washer adds the engine controls to the same water-first order, and I lay out that order from two maker manuals in my steps to start a gas pressure washer. Westinghouse’s gas manual purges before the engine starts and sets the order as engine switch on, fuel valve on, choke to the choke position for a cold engine, a slow pull on the recoil starter until resistance and then a fast pull, and the choke back to run once the engine starts. It also asks you to confirm that the washer stands on a dry, flat, level surface and that the engine has oil.

Before you refuel, complete the applicable stop and make-safe steps in the safe-state box, including letting the engine cool as the manual directs. Add only the fuel and oil the manual names, keep fuel away from flame and sparks, and wipe up spilled fuel before you start the engine. The engine and the muffler stay hot after the engine stops, so keep your hands, skin and clothing away from them. Westinghouse also says to refuel outdoors in a well-ventilated area, to leave the engine off for at least two minutes first, never to overfill, to let spilled fuel evaporate before operating and to inspect for fuel leaks after refueling.

Running the unit for more than one minute without spraying water lets heat build up in the pump, according to Westinghouse, and a thermal relief valve then opens and releases hot water. If the engine starts briefly and shuts off, squeeze the trigger to relieve the pressure before you try again.

Corded Electric: Plug, Switch and Auto-Start

A corded washer adds the plug and the power switch, and the manual steps for it are in my write-up on how to start an electric pressure washer. The ePX3500 manual says to purge first, then to plug into a grounded outlet and push the start and stop button once, and Greenworks says to connect to power, turn the switch on and pull the trigger. That model has an auto-start pump that runs for several seconds and shuts off, which its manual calls normal, and the manual warns that the unit could be pressurized even if you do not hear the motor and pump running.

That manual also says rapid trigger pulls make the auto-start miss a cycle and asks for slow, deliberate pulls. I squeeze slowly on a machine like that, and I read a silent washer as a pressurized one.

Battery: Pack, Power Button and Standby

EGO’s order connects the hoses, gun and nozzle, opens the water, then installs the battery packs and presses the power button. EGO says the washer always runs at high speed after each start, shuts itself off after 5 minutes of standby and, with only one battery pack, cannot reach its turbo speed. Then you press the unlock side of the lock-off button and squeeze the trigger until a steady stream comes out, holding the gun with both hands.

Spraying: Trigger, Grip and Nozzle Changes

Once the stream is steady, the job is control: a firm grip, safe footing and a gun that points where you intend. Handling the gun well is mostly what the manual says about the trigger, the lock and the nozzle, and the manual names the nozzle for the job.

Moving the Gun and Reading the Surface

The ePX3500 manual says surfaces become slippery when wet and extra slippery with a detergent, and the Westinghouse gas manual warns that high pressure can splash back at the operator or throw objects. That gas manual also says water under high pressure can damage fragile surfaces and asks you to practice on an inconspicuous test area, and I collect the manual warnings about what you should never pressure wash in a separate article. Check both your washer’s manual and the care instructions of the surface or finish maker before you wash, and follow their restrictions. If they prohibit pressure washing, do not use a different nozzle or setting as a workaround.

Changing a Nozzle

Before you change a nozzle, complete the stop and make-safe steps in the safe-state box. Use only the nozzles and accessories your manual permits, following its instructions for the job. Never direct any nozzle at skin, people or animals.

The Westinghouse gas manual says to engage the trigger lock before changing a nozzle, to pull on the nozzle afterwards to be sure it is secured and to use only the nozzles supplied with the washer. EGO says to hold the gun with one hand and the nozzle with the other when you disconnect it, because personal injury may result if the nozzle jumps out. I read the manual’s nozzle table before a nozzle goes on, and I never carry a setting over from another maker’s manual.

How to Use Soap in a Pressure Washer

Detergent

Before you add detergent or connect or adjust a detergent accessory, complete the applicable stop and make-safe steps in the safe-state box. Use only the detergents your manual allows, through the detergent system the manual describes, and read the detergent label before you open it. Wear the protective equipment the detergent label requires, and avoid contact of detergent with your eyes and skin. Do not run a detergent that your manual does not name through the pump.

The makers print the same boundary in different words. The Westinghouse gas manual warns that thicker products such as dish soap clog the injection system and says detergent is drawn through the pump only when the black soap nozzle is on the lance. Its ePX3500 manual names gel-like detergents, dish soap and laundry soap, and Greenworks says soap cannot be applied under high pressure with that machine. I read the detergent label before I open the container, the way I read a plant protection product label. The black soap nozzle is one color among several, and my article explains the nozzle colors each maker prints.

If someone swallows a cleaning product or gets it in the eyes, follow the label’s first-aid section and call Poison Control (America’s Poison Centers) at 1-800-222-1222. Call 911 for a fire or immediate danger.

Stopping and Releasing Trapped Pressure

Pressure stays in the hose and gun after the machine stops, so stopping has two parts: stop the machine, then release the pressure the way the manual says. The makers print different orders for it, and the table shows each one as written.

Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Each maker then prints its own stop order for its own machine, and these are the orders as written.

  • Westinghouse WPX2700, WPX3200 and WPX3400 (gas): engage the trigger lock, turn the engine switch off, close the fuel valve, turn the water supply off, then disengage the lock and depress the trigger for 15 seconds to depressurize the system. After each use, the manual lets the pressure washer cool down before it has you disconnect the high-pressure hose and the water inlet hose, drain the hoses, gun and nozzle extension, and lock the trigger. It also says never to disconnect the high-pressure hose while the system is pressurized.
  • Westinghouse ePX3500 (corded): push the start and stop button to stop the washer, then point the gun in a safe direction and pull the trigger to release the pressure. The manual says pressure may remain in the system after you stop, and never to let the pump run for more than one minute after the water supply is off.
  • Greenworks GPW3002A (corded): release the trigger, turn the power switch off, turn the water supply off, pull the trigger to release the remaining pressure, engage the lock-out, then disconnect the power cord.
  • EGO HPW3200 (battery): release the trigger and press the lock-off button to the lock position, power the washer down, close the faucet or lift the siphon hose out of the bucket, unlock the gun and squeeze the trigger to empty the water from the hoses, then disconnect the gun, hoses, wands and nozzles. EGO then has you power the washer on briefly to drain the pump, power it down and remove the battery packs. EGO says not to disconnect the gun, hoses, wands, nozzles or foam cannon while water remains in the hoses.

Only the Westinghouse gas manual prints a time for the squeeze. Never leave the machine running, plugged in or pressurized, and finish with the manual’s last step. A washer with auto-start can sit silent and still hold pressure, so I judge a stop by the manual’s last step and never by the sound.

When the Stream Weakens or Pulses

A stream that weakens, pulses or sputters is a reason to stop, never a reason to keep going. Before you inspect anything, complete the stop and make-safe steps in the safe-state box above, and resume only when you have found the cause, repaired any damage and met the manual’s restart conditions. A battery with an odor, a color change, too much heat, a change in shape, leaking or odd noises is the emergency exception in that box instead.

  • Inlet screen or filter: Greenworks lists a clogged filter, and Westinghouse asks for a look at the screen and gasket before each use.
  • Hose: Greenworks names a kinked hose and the garden hose diameter as causes of low or varying pressure.
  • Air in the pump: Greenworks says the pump may be drawing in air and to purge it by squeezing the trigger. I cover the manual checks for a pulsing pressure washer in a separate guide.
  • A blocked nozzle: the nozzle is the next place to look, and the clearing method belongs to your manual.

A nozzle that gives a weak, uneven or pulsing stream may be blocked. Complete the stop and make-safe steps in the safe-state box, then clear the nozzle only with the tool and the method your manual describes. Never look into the nozzle or point it at anyone to check it. Westinghouse names the cleaning tool in the box, EGO a cleaning needle and Greenworks a straight paper clip or cleaning tool.

Westinghouse’s gas manual adds that you should not use the washer if it sparks, smokes, emits flames or vibrates excessively. I check the cheapest causes first, the screen, the hose and the nozzle, because those are the parts I can see once the machine is isolated. My guide on a pressure washer losing pressure goes through the causes from the manuals.

Draining, Cleaning Up and Storing

Before you store the pressure washer, complete the stop and make-safe steps in the safe-state box. Drain and store it as your manual directs, in a place the manual allows and away from children. Store a battery as the battery manual describes, and fuel as the manual and the fuel container’s label describe.

After Each Use

The Westinghouse gas manual lets the washer cool, disconnects both hoses, drains the hoses, gun and nozzle extension, wipes off the water and pulls the recoil handle five or six times with the engine off to clear liquid from the pump. The ePX3500 manual releases the pressure, unplugs, wraps the cord and hose on their retainers and tilts the unit to drain the inlet. Greenworks asks for the power cord and water hose to come off and the gun, hose and washer to be dry. My guide to gas versus electric pressure washers compares fuel, cord and care side by side.

EGO’s flush steps start with the battery pack removed and the hose and accessories off the outlet port, then run water through the washer for at least 120 seconds before storage. EGO asks for a dry, well-ventilated place, locked up or up high, out of the reach of children.

Before you clean the machine, check or clean the inlet filter, or do any other maintenance, complete the stop and make-safe steps in the safe-state box. Do the maintenance your manual describes, in the order it describes it, and do not use a part or an accessory the maker does not name.

Winter and Freezing

Water left in a pump can freeze, and the makers treat it as a storage rule. The ePX3500 manual says freezing water will crack the pump and its label says not to store the washer where the temperature could drop below 40 F. The Westinghouse gas manual asks for RV antifreeze or a similar pump protection made for pressure washers before winter, Greenworks asks for a frost-free area, and EGO’s winterizing steps use a pump protector sold separately. In an unheated shed, water left in a pump can freeze in a cold snap, so draining the pump is a fixed step, not an extra. I explain the pump, hose, gun and nozzle in my article on how a pressure washer works.

Wash Water and Storm Drains

Before you wash, plan how to keep wash water, detergent and debris out of streets, storm drains, ditches and streams, because a storm drain carries what enters it to local waters without treatment. Check with your city or county stormwater office about collecting and disposing of the wash water for the job. Send wash water to landscaping only where local rules and the detergent label permit it and the soil can absorb it without runoff or contamination. Otherwise contain and collect it for an approved disposal route.

Do not assume that water carrying oil, paint debris, pesticide residue or material from an old treated deck is suitable for a lawn. The wood risks and the safety checks of that job are in my article on how to pressure wash a deck.

My Routine Before and After Every Job

Three things carry the whole method: the manual of the exact machine comes first, water goes on before the machine starts, and the pressure is released before a hand goes near a hose or a nozzle. My own tip is to keep the manual next to the machine and mark the stop section. Next, read your washer’s stop section line by line and compare it with the box above. That order is how to use a pressure washer in practice: water first, the lock on, and the pressure released before anything comes apart. Once the machine is set up, I take the whole job in order, from plan to cleanup, in my walk-through on how to pressure wash a house.

Frequently Asked Questions

How do you use a pressure washer for the first time?

You use a pressure washer for the first time by reading its manual, finishing the assembly and then turning the water on first and following the manual’s purge and start order, with the trigger lock on whenever you stop. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Greenworks says not to power the machine on before it is assembled completely.

How do you use soap in a pressure washer?

You use soap in a pressure washer only through the detergent system and the nozzle your manual describes, with a detergent made for pressure washers. Before you add detergent, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Westinghouse and Greenworks say the soap nozzle must be fitted for detergent to flow, and Greenworks says soap cannot be applied under high pressure with that machine.

How do you use a pressure washer safely?

You use a pressure washer safely by following your manual first, completing the stop and make-safe steps in the safe-state box above before every hands-on step, and keeping the spray away from people, pets and your own hands and feet. Wear safety glasses or goggles and closed footwear, and engage the trigger lock whenever you stop spraying. Gas models run outdoors only, and corded models need the GFCI protection the manual specifies.

How do you use a pressure washer without an outside tap?

You use a pressure washer without an outside tap only on a water supply your manual allows. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. The Westinghouse and Greenworks manuals call for a water main or pressurized spigot, and EGO’s HPW3200 manual also describes a bucket fed through its siphon hose and filter.

Do you run water before starting a pressure washer?

You run water through a pressure washer before you start it, because the pump needs a steady flow first. Before you do this, complete the stop and make-safe steps for your pressure washer in the safe-state box above. Westinghouse, Greenworks and EGO all say to connect the water and turn it on before the machine runs, and Westinghouse and EGO warn that running it dry can damage the high-pressure seals.

References

  1. Funato N, Sugizaki Y, Ri Y, Ichibayashi R. High-pressure injection damage caused by a high-pressure washer. Cureus. 2024;16(1):e52498. doi:10.7759/cureus.52498
  2. Johnson C, Newton W, LaRochelle L, Allen J, Daly C. High-pressure injection injuries of the hand in community and industrial settings: incidence and trends. Hand (N Y). 2025;20(6):917-922. doi:10.1177/15589447231218404
  3. Choi JH, Choi SY, Hwang JH, Kim KS, Lee SY. Finger compartment syndrome due to a high-pressure washer injury: a case report. World J Clin Cases. 2023;11(13):3017-3021. doi:10.12998/wjcc.v11.i13.3017
  4. Placide J, Yang MY, Gross AW, Crowell EL. Case series: traumatic ocular lacerations secondary to pressure washers. Am J Ophthalmol Case Rep. 2022;27:101612. doi:10.1016/j.ajoc.2022.101612
  5. Alexander BM, Graydon PS, Pena M, Feng HA, Beamer BR. Hazardous exposures and engineering controls in the landscaping services industry. J Occup Environ Hyg. 2025;22(3):189-202. doi:10.1080/15459624.2024.2439810
  6. Earnest GS, Mickelsen RL, McCammon JB, O’Brien DM. Carbon monoxide poisonings from small, gasoline-powered, internal combustion engines: just what is a “well-ventilated area”? Am Ind Hyg Assoc J. 1997;58(11):787-791. doi:10.1080/15428119791012289

Safety Note: Read your pressure washer’s manual before you connect water or power, and follow it. Never point the spray at yourself, another person, a pet or any part of the body. Keep hands and feet away from the nozzle and stream. Get medical care without delay for a spray wound, even if it looks minor at first. Tell the clinician that a pressure washer caused the injury. Wear safety glasses or goggles and closed footwear before operating the washer, plus any additional protection required by the manual and the detergent label. Follow the manual’s instructions for the trigger lock, grip, footing and recoil, and engage the trigger lock whenever you stop spraying. Use only the nozzles, accessories and detergents the manual permits, and never point any nozzle at skin, people or animals. Do not perform a task at height without instructions expressly permitting the equipment and method in the exact manual. Gas models: operate outdoors, never inside a building or a partly enclosed space. Keep the engine at least 20 feet from any window, door or vent, following CDC’s pressure washer guidance and any stricter manual requirement. Exhaust contains carbon monoxide, which cannot be seen or smelled and can kill. Opening doors or windows does not make indoor operation safe. Refuel only with the engine off and cool, following the manual. Corded models: use the manual’s specified electrical supply and GFCI protection, and test the GFCI before use according to its instructions. After an operating GFCI or breaker trip, do not reuse the washer until a qualified repair person has examined it. Where the washer has a grounding prong, connect it to a properly grounded receptacle and never remove the prong. Wear closed, rubber-soled footwear that provides some electrical insulation, plus any additional footwear required by the manual; footwear does not replace GFCI protection or the other electrical precautions. Never cut or splice cords. Use an extension cord only as the manual permits. Keep connections dry and away from runoff, standing water and the washing area, and keep spray away from electrical equipment. Battery models: use only the battery and charger the maker specifies for your exact model. Emergency first: if you notice an unusual odor, a change in color, too much heat, a change in shape, leaking or odd noises from a lithium-ion battery, stop using the washer and follow your battery manual’s emergency instructions. Otherwise, complete the applicable stop and make-safe procedure before hose, nozzle, wand or accessory work, clearing a blockage, cleaning, maintenance, refueling, checking oil, adding detergent, battery changes or charging, draining, moving, transporting, storing or leaving the washer. Follow your exact manual’s procedure and order. Release the trigger and engage its lock. Gas: switch the engine off and wait for it to stop; disconnect the spark plug wire before service as the manual directs, and let hot parts cool before refueling, storage or contact. Corded: switch off and unplug by the plug with dry hands. Battery: switch off, remove a removable battery as the manual directs and keep it away while working; for a built-in battery, follow the manual’s isolation procedure and do not open the battery compartment. Complete the manual’s water-supply shutdown and pressure-relief steps: point the gun in a safe direction at a permitted discharge location, disengage the trigger lock, squeeze the trigger as directed to relieve pressure, then reengage the lock. Do not disconnect hoses or change nozzles until pressure is relieved. If pressure cannot be relieved by the prescribed procedure, obtain service without loosening fittings. Refit and inspect parts before restoring water or power. Replace a damaged high-pressure hose; never repair or patch it. Before you wash, plan how to keep wash water, detergent and debris out of streets, storm drains, ditches and streams, and check with your city or county stormwater office about collection and disposal. Send wash water to landscaping only where local rules and the detergent label permit it and the soil can absorb it without runoff or contamination. Keep children and pets away, and never let a child use the machine. Drain and store the washer as its manual directs. For exposure to a cleaning product, follow the label’s first-aid instructions and call Poison Control at 1-800-222-1222. Call 911 for a fire or immediate danger.

Scroll to Top